Atomic structure and formation mechanism of identically sized Au clusters grown on Si(111)-(7×7) surface

Identically sized Au clusters are grown on the Si(111)-(7×7) surface by room temperature deposition of Au atoms and subsequent annealing at low-temperature. The topographical images investigated by in situ scanning tunneling microscopy show a bias-dependent feature. The current-voltage properties measured by scanning tunneling spectroscopy indicate some semiconducting characteristics of the Au adsorbed surface, which is attributable to the saturation of Si dangling bonds. These experimental results, combined with the simulated scanning tunneling microscopy images and the first-principles adsorption energy calculations, show that the Au cluster is most likely to have a Au(6)Si(3) structure. In the Au(6)Si(3) cluster, three adsorbed Au atoms replace the three Si center adatoms, forming a hollow triangle, while the replaced Si atoms and other three Au atoms connect into a hexagon locating within the triangle. The formation mechanism of this atomic configuration is intimately associated with the complicated chemical valences of Au and the specific annealing conditions.     

Formation of trioctylamine from octylamine on Au(111)

The adsorption of octylamine on Au(111) under ultrahigh vacuum conditions is investigated. The molecules surprisingly undergo a thermally activated chemical reaction, resulting in formation of trioctylamine as confirmed both by X-ray photoelectron spectroscopy (XPS) and by comparison to the scanning tunneling microscopy (STM) signature of trioctylamine deposited directly onto the surface.     

Single-molecule magnets: a new approach to investigate the electronic structure of Mn12 molecules by scanning tunneling spectroscopy

A new approach to the deposition of Mn12 single-molecule magnet monolayers on the functionalized Au(111) surface optimized for the investigation by means of scanning tunneling spectroscopy was developed. To demonstrate this method, the new Mn12 complex [Mn12O12(O2CC6H4F)16(EtOH)4].4.4CHCl3 was synthesized and characterized. In MALDI-TOF mass spectra the isotopic distribution of the molecular ion peak of the latter complex was revealed. The complex was grafted to Au(111) surfaces via two different short conducting linker molecules. The Mn12 molecules deposited on the functionalized surface were characterized by means of scanning tunneling microscopy showing homogeneous monolayers of highest quality. Scanning tunneling spectroscopy measurements over a wider energy range compared with previous results could be performed because of the optimized Au(111) surface functionalization. Furthermore, the results substantiate the general suitability of short acidic linker molecules for the preparation of Mn12 monolayers via ligand exchange and represent a crucial step toward addressing the magnetic properties of individual Mn12 single-molecule magnets.     

Thiol with an unusual adsorption-desorption behavior: 6-mercaptopurine on Au(111)

A multitechnique study of 6-mercaptopurine (6MP) adsorption on Au(111) is presented. The molecule adsorbs on Au(111), originating short-range ordered domains and irregular nanosized aggregates with a total surface coverage by chemisorbed species smaller than those found for alkanethiol SAMs, as derived from scanning tunneling microscopy (STM) and electrochemical results. X-ray photoelectron spectroscopy (XPS) results show the presence of a thiolate bond, whereas density functional theory (DFT) data indicate strong chemisorption via a S-Au bond and additional binding to the surface via a N-Au bond. From DFT data, the positive charge on the Au topmost surface atoms is markedly smaller than that found for Au atoms in alkanethiolate SAMs. The adsorption of 6MP originates Au atom removal from step edges but no vacancy island formation at (111) terraces. The small coverage of Au islands after 6MP desorption strongly suggests the presence of only a small population of Au adatom-thiolate complexes. We propose that the absence of the Au-S interface reconstruction results from the lack of significant repulsive forces acting at the Au surface atoms.     

Using image resonances to probe molecular conduction at the n-heptane/Au(111) interface

The binding energies and lifetimes of the n=1 image resonance on Au(111) are measured as a function of n-heptane layer thickness by femtosecond time-resolved two-photon photoemission (TR-2PPE) spectroscopy. The lifetime of the image resonance dramatically increases from approximately 4 fs on clean Au(111) to 1.6 ps with three layers of n-heptane. Because the image resonance is above the L1 band edge of Au, this increase in lifetime is attributed to the tunneling barrier presented by the sigma-sigma* band gap of the n-heptane film. We use the one-dimensional dielectric continuum model (DCM) to approximate the surface potential and to determine the binding energies and the lifetimes of the image resonances. The exact solution of the DCM potential is determined in two ways: the first by wave-packet propagation and the second by using a tight-binding Green's function approach. The first approach allows band-edge effects to be treated. The latter approach is particularly useful in illustrating the similarity between TR-2PPE and conductance measurements.     

Interaction of carbon monoxide with Au(111) modified by ion bombardment: a surface spectroscopy study under elevated pressure

Gold based model systems exhibiting the structural versatility of nanoparticle ensembles and being accessible for surface spectroscopic investigations are expected to provide new information about the adsorption of carbon monoxide, a key process influencing the CO oxidation activity of this noble metal in nanoparticulate form. Accordingly, in the present work the interaction of CO is studied with an ion bombardment modified Au(111) surface by means of a combination of photoelectron spectroscopy (XPS and UPS), sum frequency generation vibrational spectroscopy (SFG), and scanning tunneling microscopy (STM). While no adsorption was found on intact Au(111), data collected on the ion bombarded surface at cryogenic temperatures indicated the presence of stable CO adsorbates below 190 K. A quantitative evaluation of the C 1s XPS spectra and the surface morphology explored by STM revealed that the step edge sites created by ion bombardment are responsible for CO adsorption. The identification of the CO binding sites was confirmed by density functional theory (DFT) calculations. Annealing experiments up to room temperature showed that at temperatures above 190 K unstable adsorbates are formed on the surface under dynamic exposure conditions that disappeared immediately when gaseous CO was removed from the system. Spectroscopic data as well as STM records revealed that prolonged CO exposure at higher pressures of up to 1 mbar around room temperature facilitates massive atomic movements on the roughened surface, leading to its strong reordering toward the structure of the intact Au(111) surface, accompanied by the loss of the CO binding capacity.     

Scanning tunneling microscopy of self-assembled phenylene ethynylene oligomers on Au(111) substrates

In this paper, we report the self-assembly, electrical characterization, and surface modification of dithiolated phenylene-ethynylene oligomer monolayers on a Au(111) surface. The self-assembly was accomplished by thiol bonding the molecules from solution to a Au(111) surface. We have confirmed the formation of self-assembled monolayers by scanning tunneling microscopy (STM) and optical ellipsometry, and have studied the kinetics of film growth. We suggest that self-assembled phenylene ethynylene oligomers on Au(111) surfaces grow as thiols rather than as thiolates. Using low-temperature STM, we collected local current-voltage spectra showing negative differential resistance at 6 K.     

HREELS, STM, and STS study of CH(3)-terminated Si(111)-(1x1) surface

An ideally (1x1)-CH(3)(methyl)-terminated Si(111) surface was composed by Grignard reaction of photochlorinated Si(111) and the surface structure was for the first time confirmed by Auger electron spectroscopy, low energy electron diffraction, high-resolution electron energy loss spectroscopy (HREELS), scanning tunneling microscopy (STM), and scanning tunneling spectroscopy (STS). HREELS revealed the vibration modes associated to the CH(3)-group as well as the C-Si bond. STM discerned an adlattice with (1x1) periodicity on Si(111) composed of protrusions with internal features, covering all surface terraces. The surface structure was confirmed to be stable at temperatures below 600 K. STS showed that an occupied-state band exists at gap voltage of -1.57 eV, generated by the surface CH(3) adlattice. This CH(3):Si(111)-(1x1) adlayer with high stability and unique electronic property is prospective for applications such as nanoscale lithography and advanced electrochemistry.     

Solvent effects on the adsorption and self-organization of Mn12 on Au(111)

A sulfur-containing single molecule magnet, [Mn12O12(O2CC6H4SCH3)16(H2O)4], was assembled from solution on a Au(111) surface affording both submonolayer and monolayer coverages. The adsorbate morphology and the degree of coverage were inspected by scanning tunneling microscopy (STM), while X-ray photoelectron spectroscopy (XPS) allowed the determination of the chemical nature of the adsorbate on a qualitative and quantitative basis. The properties of the adsorbates were found to be strongly dependent on the solvent used to dissolve the magnetic complex. In particular, systems prepared from tetrahydrofuran solutions gave arrays of isolated and partially ordered clusters on the gold substrate, while samples prepared from dichloromethane exhibited a homogeneous monolayer coverage of the whole Au(111) surface. These findings are relevant to the optimization of magnetic addressing of single molecule magnets on surfaces.     

In situ STM investigation of gold reconstruction and of silicon electrodeposition on Au(111) in the room temperature ionic liquid 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide

The electrodeposition of silicon on Au(111) was investigated by cyclic voltammety (CV) and by in situ scanning tunneling microscopy (STM) in the room temperature ionic liquid 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide with a SiCl(4) concentration of 0.1 mol/L. A main reduction process begins in the cyclic voltammogram at about -1800 mV versus ferrocene/ferrocinium, which is correlated to the electrodeposition of elemental semiconducting silicon. It has been found that at an electrode potential more negative than the open circuit potential (OCP), the Au(111) surface is subject to a restructuring/reconstruction both in the case of the pure ionic liquid and in the presence of SiCl(4). The first STM-probed silicon islands with 150-450 pm in height appear at about -1700 mV versus ferrocene/ferrocinium. Their lateral and vertical growth leads to the formation of a rough layer with silicon islands of up to 1 nm in height. At about -1800 mV the islands merge and form silicon agglomerates. In situ I/U tunneling spectroscopy reveals a band gap of 1.1 +/- 0.2 eV for layers of about 5 nm in height, a value that has to be expected for semiconducting silicon.     

Toward Raman fingerprints of single dye molecules at atomically smooth Au(111)

The creation of a highly enhanced electromagnetic (EM) field underneath a scanning tunneling microscope (STM) tip enables Raman spectroscopic studies of organic submonolayer adsorbates at atomically smooth single crystalline surfaces. To study the sensitivity of this technique, tip-enhanced resonance Raman (TERR) spectra of the dye malachite green isothiocyanate on Au(111) in combination with the corresponding STM images of the probed surface region were analyzed. The detection limit for unambiguous identification of the dye and semiquantitative determination of the surface coverage reaches < or =0.7 pmol/cm(2), or approximately five molecules present in the enhanced-field region, which is confirmed by STM images. Because of well-defined adsorption sites at atomically smooth Au(111) surfaces, no variation in band positions or relative band intensities was observed at the single- or few-molecule detection level when employing TERR spectroscopy.     

Electrochemical modification of surface morphology of Au/Ti bilayer films deposited on a Si prism for in situ surface-enhanced infrared absorption (SEIRA) spectroscopy

Surface-enhanced infrared absorption (SEIRA)-active Au/Ti bilayer films sputter deposited on Si substrates have been prepared by an electrochemical annealing (ECA) treatment for the first time. The application of Au/Ti bilayer films on Si substrates to the spectroscopic technique is a promising alternative to the conventional technique using directly deposited Au films on Si substrates, offering excellent adhesive durability of the deposited metal films. However, Au/Ti bilayer films have never been selected for the spectroscopy technique because the films in the as-prepared state exhibit relatively smooth surface morphology: the excitation of the localized surface plasmon is vital to achieving SEIRA enhancements but could hardly be observed on the smooth morphology. It is shown by ex situ scanning tunneling microscopy measurements that the unfavorable smooth morphology of the as-prepared Au/Ti bilayer films can be modified by the ECA treatment to a reasonably rough, island-structure morphology similar to that of the conventional SEIRA-active Au films. In situ infrared absorption spectroscopy of adsorbed sulfate anions has been conducted on the Au/Ti bilayer film both before and after ECA treatment. The spectroscopy measurements demonstrate that the SEIRA activity of the film after being subjected to the treatment is significantly improved so that the technique could detect adsorbates on the film electrodes even with the submonolayer coverage. As an additional benefit, the ECA treatment has brought about a substantial increase in the fraction of Au(111) domains on the polycrystalline Au film surfaces. Accordingly, this approach enables us to prepare SEIRA-active Au films having sufficient adhesion to the Si substrates as well as the highly preferred (111) orientation.     

An in situ STM and DTS study of the extremely pure [EMIM]FAP/Au(111) interface

Herein the structure of the interfacial layer between the air- and water-stable ionic liquid 1-ethyl-3-methylimidazolium tris(pentafluoroethyl)trifluorophosphate ([EMIM]FAP) and Au(111) is investigated using in situ scanning tunneling microscopy (STM), distance tunneling spectroscopy (DTS) and cyclic voltammetry (CV) measurements. The in situ STM measurements reveal that structured interfacial layers can be probed in both cathodic and anodic regimes at the IL/Au(111) interface. The structure of these layers is dependent on the applied electrode potential, the number of subsequent STM scans and the scan rate. Furthermore, first DTS results show that the tunneling barrier during the 1st STM scan does not seem to change significantly in the cathodic potential regime between the ocp (-0.2 V) and -2.0 V.     

4-Mercaptopyridine on Au(111): a scanning tunneling microscopy and spectroscopy study

The adsorption of 4-mercaptopyridine (4MPy) molecules on reconstructed Au(111) is investigated by Scanning Tunneling Microscopy (STM) and Spectroscopy (STS) at low temperature and under ultra-high vacuum (UHV) conditions. As made visible by STM, at low coverage (<10%) 4MPy adsorbs preferentially at elbow sites of the Herringbone reconstruction and at step edges of the Au(111). Increasing coverage (but still <30%) results in formation of molecular chains followed, at even higher coverage, by a 3-dimensional growth. Detailed analysis of z-V spectroscopy (ramping the tunneling bias V while keeping the tunneling current constant) provides information on the bias dependent apparent height of a single 4MPy/Au(111) as well as on the local density of states (LDOS) of single and chain 4MPy molecules in comparison to the bare Au(111) surface revealing a significant shift of the lowest unoccupied molecular orbital (LUMO) towards lower energy for molecules within chains. Additionally, the data provide no evidence that for these samples prepared in UHV the adsorption of 4MPy on Au(111) requires mediating Au adatoms. Also, clear indications are given that the adsorption does not induce a strong reduction of the Au DOS close to its Fermi energy. Finally, in context of the apparent STM height of 4MPy molecules, the behavior of the differential barrier height Φ(diff)(V) = (?(z)?(V)I/?(V)I)(2) on bare Au(111) and 4MPy/Au(111) is analyzed and the corresponding experimental values are applied to recover the LDOS of the molecule for unoccupied states according to a previously published numerical recipe [B. Koslowski, H. Pfeifer and P. Ziemann, Phys. Rev. B, 2009, 80, 165419 and M. Ziegler, N. Néel, A. Sperl, J. Kr?ger, and R. Berndt, Phys. Rev. B, 2009, 80, 125402]. In this way, one obtains a spectrum comprising a constant DOS of the Shockley-like surface state of Au(111) and a Lorentzian line attributed to the LUMO of 4MPy.     

Complex surface chemistry of 4-mercaptopyridine self-assembled monolayers on Au(111)

The adsorption of 4-mercaptopyridine on Au(111) from aqueous or ethanolic solutions is studied by different surface characterization techniques and density functional theory calculations (DFT) including van der Waals interactions. X-ray photoelectron spectroscopy and electrochemical data indicate that self-assembly from 4-mercaptopyridine-containing aqueous 0.1 M NaOH solutions for short immersion times (few minutes) results in a 4-mercaptopyridine (PyS) self-assembled monolayer (SAM) with surface coverage 0.2. Scanning tunneling microscopy images show an island-covered Au surface. The increase in the immersion time from minutes to hours results in a complete SAM degradation yielding adsorbed sulfur and a heavily pitted Au surface. Adsorbed sulfur is also the main product when the self-assembly process is made in ethanolic solutions irrespective of the immersion time. We demonstrate for the first time that a surface reaction is involved in PyS SAM decomposition in ethanol, a surface process not favored in water. DFT calculations suggest that the surface reaction takes place via disulfide formation driven by the higher stability of the S-Au(111) system. Other reactions that contribute to sulfidization are also detected and discussed.     

On-Surface Assembly of Au-Dicyanoanthracene Coordination Structures on Au(111)

On-surface metal-organic coordination provides a promising way for synthesizing different two-dimensional lattice structures that have been predicted to possess exotic electronic properties. Using scanning tunneling microscopy (STM) and spectroscopy (STS), we studied the supramolecular self-assembly of 9,10-dicyanoanthracene (DCA) molecules on the Au(111) surface. Close-packed islands of DCA molecules and Au-DCA metal-organic coordination structures coexist on the Au(111) surface. Ordered DCA₃Au₂ metal-organic networks have a structure combining a honeycomb lattice of Au atoms with a kagome lattice of DCA molecules. Low-temperature STS experiments demonstrate the presence of a delocalized electronic state containing contributions from both the gold atom states and the lowest unoccupied molecular orbital of the DCA molecules. These findings are important for the future search of topological phases in metal-organic networks combining honeycomb and kagome lattices with strong spin-orbit coupling in heavy metal atoms.     

Self-Assembled Monolayers of N-Heterocyclic Olefins on Au(111)

Self-assembled monolayers (SAMs) of N-heterocyclic olefins (NHOs) have been prepared on Au(111) and their thermal stability, adsorption geometry, and molecular order were characterized by X-ray photoelectron spectroscopy, polarized X-ray absorption spectroscopy, scanning tunneling microscopy (STM), and density functional theory (DFT) calculations. The strong σ-bond character of NHO anchoring to Au induced high geometrical flexibility that enabled a flat-lying adsorption geometry via coordination to a gold adatom. The flat-lying adsorption geometry was utilized to further increase the surface interaction of the NHO monolayer by backbone functionalization with methyl groups that induced high thermal stability and a large impact on work-function values, which outperformed that of N-heterocyclic carbenes. STM measurements, supported by DFT modeling, identified that the NHOs were self-assembled in dimers, trimers, and tetramers constructed of two, three, and four complexes of NHO−Au-adatom. This self-assembly pattern was correlated to strong NHO−Au interactions and steric hindrance between adsorbates, demonstrating the crucial influence of the carbon-metal σ-bond on monolayer properties.     

Scanning tunneling microscopy study of the structure and orbital-mediated tunneling spectra of cobalt(II) phthalocyanine and cobalt(II) tetraphenylporphyrin on au(111): mixed composition films

Binary thin films of cobalt(II) phthalocyanine (CoPc) and cobalt(II) tetraphenylporphyrin (CoTPP) were prepared at submonolayer coverage on Au(111)/mica substrates byvapor deposition. All sample preparation and analysis were done under an ultrahigh vacuum. Scanning tunneling microscopy (STM) constant-current images of CoPc/CoTPP mixtures showed two close-packed surface structures, with different compositional percentages and some disorder. CoPc was also observed exclusively in one-dimensional chains and as single, isolated molecules below 220 K. Occupied and unoccupied orbital energy levels were identified by STM and tunnel-diode-based orbital-mediated tunneling spectroscopy. Occupied energy levels were also confirmed by ultraviolet photoelectron spectroscopy. The transient oxidation of the Co d(z2) orbital is identified in STM dI/dV(V) curves just negative of the 0 V sample bias for both molecules. Nearly identical constant-current contours are observed over the central Co2+ ions of CoTPP and CoPc, indicating that the attenuation of the d(z)2 orbital-mediated tunneling current induced by the structure of TPP relative to Pc is at most a factor of about 10. The orbital-mediated tunneling spectra of CoTPP and CoPc are distinctly different and allow these structurally similar species to be differentially identified.     

Synthesis of TiO2 nanoparticles on the Au(111) surface

The growth of titanium oxide nanoparticles on reconstructed Au(111) was investigated by scanning tunneling microscopy and x-ray photoelectron spectroscopy. Ti was deposited by physical-vapor deposition at 300 K. Regular arrays of titanium nanoparticles form by preferential nucleation of Ti at the elbow sites of the herringbone reconstruction. The titanium oxide nanoclusters were synthesized by subsequent exposure to O(2) at 300 K. Two-and three-dimensional titanium oxide nanocrystallites form during annealing in the temperature range from 600 to 900 K. At the same time, the Au(111) surface assumes a serrated 110-oriented step-edge morphology suggesting step-edge pinning by titanium oxide nanoparticles. The oxidation state of the titanium oxide nanoparticles varies with annealing temperature. Specifically, annealing to 900 K results in the formation of stoichiometric TiO(2) nanocrystals as judged by the Ti(2p) binding energies measured in the x-ray photoelectron data. The nanodispersed TiO(2) on Au(111) is an ideal system to test the various models proposed for the enhanced catalytic reactivity of supported Au nanoparticles.     

Au单晶表面氟表面活性剂FSN自组装膜的电化学行为

研究Au(111)和Au(100)表面非离子型氟表面活性剂FSN自组装膜的电化学行为.电化学扫描隧道显微术和循环伏安法测试表明,在0～0.8 V电位区间,FSN自组装膜未发生氧化还原,均一性好,可稳定地存在于电极表面,并显著抑制硫酸根离子在电极表面的吸附和Au单晶表面的重构.在FSN自组装膜Au单晶电极的初始氧化阶段,Au(111)表面有少量突起,而Au(100)表面呈现台阶剧烈变化,但FSN自组装膜的吸附结构没有改变.与Au(100)表面相比,Au(111)表面形成的FSN自组装膜可更有效地抑制Au表面的氧化.