多孔TiO2/Al/SiO2纳米复合结构的紫外光吸收特性研究

在SiO₂玻璃衬底上用脉冲激光沉积(PLD)技术，分别沉积Ti和Ti/Al膜，经电化学阳极氧化成功制备了多孔TiO₂/SiO₂和TiO₂/Al/SiO₂纳米复合结构. 其中TiO₂薄膜上的微孔阵列高度有序，分布均匀. 实验研究了Al过渡层对多孔TiO₂薄膜光吸收特性的影响. 结果表明：无Al过渡层的多孔TiO₂薄膜其紫外吸收峰在27     

多孔TiO2/Al/SiO2纳米复合结构的紫外光吸收特性研究

在SiO2玻璃衬底上用脉冲激光沉积(PLD)技术,分别沉积Ti和Ti/Al膜,经电化学阳极氧化成功制备了多孔TiO2/SiO2和TiO2/Al/SiO2纳米复合结构.其中TiO2薄膜上的微孔阵列高度有序,分布均匀.实验研究了Al过渡层对多孔 TiO2薄膜光吸收特性的影响.结果表明:无Al过渡层的多孔 TiO2薄膜其紫外吸收峰在270 nm处.且峰强不随阳极氧化工艺参数调节;而有Al过渡层的多孔TiO2薄膜其紫外吸收峰红移至293 nm处,峰强和峰形不仅受阳极氧化电压调节而且受Al过渡层厚度的影响也很敏感.进一步分析了两种结构在吸收边附近的光跃迁特性.这些结果对基于多孔 TiO2的光伏电池和紫外光传感器的应用研究非常有益.     

有序TiO2纳米管阵列结构的可控生长及其物相研究

分别在HF水溶液、含NH₄F和H₂O的乙二醇有机溶液中对Ti箔进行阳极氧化,得到TiO₂纳米管阵列结构.该结构高度有序、分布均匀、垂直取向,且通过阳极氧化工艺条件(如阳极氧化电压、电解液的选择与配比以及氧化时间等)可实现对其结构参数(如管径、管壁厚度、管密度、管长等)的有效控制.利用XRD研究了TiO₂纳米管阵列的物相结构.结果表明：退火前的TiO₂纳米管阵列为无定形结构;分别在真空和氧气氛中50 关键词： 2纳米管阵列')" href="#">TiO₂纳米管阵列 阳极氧化 可控生长     

TiO2/SiO2多层膜的带隙结构及光催化性能

利用传输矩阵法设计了由SiO2、TiO2组成的多层膜高透射率光子晶体结构,并分析了其透射谱特性,根据等效层原理改变多层膜一维光子晶体的自身结构来提高通带内特征波长附近的透射率,获得了最佳结构参数。研究结果表明,当晶格参数为150nm,填充比为0.346,周期数为6时,400nm波长附近吸收带处的透射率最低也可达96.5%,并且不论是TM模式还是TE模式,入射角在0°～45°范围内仍保持高的透射率,该结构可望用于空气净化装置以提高SiO2、TiO2光催化剂的光催化效率。     

反应溅射法制备TiO2薄膜

报道了用反应溅射法制备TiO₂薄膜的实验研究.详细研究了氧分压、基底温度和退火温度对成膜结构的影响.制备出了具有金红石和锐钛矿晶体结构的TiO₂薄膜.分析了金红石和锐钛矿晶体的形成条件,并对薄膜的表面形貌进行了测量. 关键词： 反应溅射 2薄膜')" href="#">TiO₂薄膜     

阳极氧化法制备Y型TiO2纳米管

在含有质量分数为0.5%的NH₄F和体积分数为5% 的H₂O的乙二醇混合溶液中,采用三步阳极氧化法制备了表面形貌高度有序的Y型TiO₂纳米管阵列。讨论了钛片预处理过程对优化TiO₂纳米管阵列表面形貌的影响以及采用升温法制备Y型TiO₂纳米管的内在机理,并在较宽的温度范围内(20~60 ℃)对钛片进行阳极氧化。实验结果表明当阳极氧化第三步的电解液温度设置在40 ℃以上时,Y型TiO₂纳米管阵列的顶端将出现环状纳米线、管壁破裂以及管长减小等现象,不利于保证Y型TiO₂纳米管阵列的整体质量。因此,30~40 ℃是选取阳极氧化第三步温度的理想范围。     

水热法制备TiO2薄膜的研究

采用水热法在玻璃基片上制备了TiO2薄膜.利用x射线衍射(XRD)、x射线光电子能谱(XPS)、扫描电子显微镜(SEM)等分析测试手段对所制备的TiO2薄膜的相结构、表面化学组成及形貌等进行了分析和表征,研究了不同水热条件对所制备TiO2薄膜的光吸收特性的影响.结果表明,所制备的薄膜为锐钛矿型TiO2,均匀、致密、无可视缺陷,具有优异的可见光透过性和紫外吸收特性 关键词： 水热法 TiO2薄膜 比消光度     

基于AAO模板的TiO2微纳结构及其光电特性

以多孔氧化铝（AAO）和导电玻璃FTO为基底,用射频（RF）磁控溅射法和溶胶凝胶（Sol-gel）法分别制备了微纳结构的TiO₂,两种TiO₂沉积技术各自体现出其特质。从XRD衍射光谱和拉曼散射光谱可以看到,在相同退火条件下,RF和Sol-gel法制备的TiO₂晶相结构不同。在以导电玻璃FTO为基底时,RF制备的薄膜颗粒分布均匀,没有团簇现象;而Sol-gel制备的薄膜由密实的颗粒构成。在以AAO为模板时,Sol-gel制备的TiO₂溶胶粒子由于胶体溶液的流动性使其对孔的填充率保持较高的水平;而RF制备的TiO₂对孔的填充率则降低。光电流实验的结果表明,前者具有更好的光电特性。     

溶胶-凝胶法制备纳米多孔SiO2薄膜

以正硅酸乙酯(TEOS)为原料，采用旋转涂敷的方法，结合溶胶-凝胶技术在硅衬底上制备超低介电常数多孔SiO₂薄膜.采用两种不同的改性方法对薄膜表面进行改性，傅里 叶变换红外光谱分析发现改性后薄膜中含有大量的—CH₃键，从而减少了孔洞塌陷.用扫 描电子显微镜观察薄膜的表面形貌，发现薄膜内孔洞尺寸在70—80 nm之间.调节溶胶pH值，发现pH值越小凝胶时间越长.对改性样品热处理的结果表明，在300 ℃时介电常数最低达2.05. 关键词： 2')" href="#">多孔SiO₂ 低介电常数 溶胶-凝胶     

纳米TiO2多孔薄膜电极平带电势的研究

采用光谱电化学方法研究了纳米TiO₂多孔薄膜电极的平带电势,获得了薄膜厚度以及TiCl₄处理对纳米TiO₂薄膜电极平带电势的影响情况,并研究了平带电势对染料敏化太阳电池光伏性能的影响.结果表明,可以通过检测纳米TiO₂电极平带电势的变化趋势来反映电池中TiO₂电极平带电势的变化趋势.随着TiO₂电极膜厚的增加,其平带电势将向正方向移动,导致对应电池的开路电压随之减小.另外,经 关键词： 平带电势 2')" href="#">纳米TiO₂ 染料敏化 太阳电池     

C掺杂锐钛矿相TiO2吸收光谱的第一性原理研究

运用第一性原理,对C掺杂锐钛矿相TiO₂的电子结构进行了研究,从能带结构理论解释了C掺杂TiO₂吸收光谱的一些实验现象.发现在C掺杂后的锐钛矿相TiO₂的禁带宽度增大,并且在带隙中出现了杂质能级,这些杂质能级主要是由C 2p轨道上的电子构成的,它们之间是独立的,正是这些独立的杂质能级使TiO₂掺杂后可以发生可见光响应.价带上的电子可以吸收一定能量的光子跃迁到杂质能级,而杂质能级上的电子也可以吸收一定能量的光子跃迁到导带,所以从理论上可以计算出掺杂后的TiO₂在可见光范围内存在两个吸收边,与实验中所得到的现象相一致.     

低成本溶胶-凝胶法制备SiO2/TiO2双层膜的减反射与自清洁性能

将玻璃基底依次在低成本的SiO₂溶胶和TiO₂溶胶中浸渍后,在500 oC下煅烧制备了同时具备减反射与自清洁性能的SiO₂/TiO₂双层膜．该膜的光学性能与结构特征分别通过紫外-可见分光光度计和场发射扫描电镜进行了表征．同时,源于超亲水性和光催化作用的自清洁性能也凸显出来．实验结果表明制备SiO₂/TiO₂双层膜对光的透射率最高可达到95%,同时具备自清洁性能．     

Preparation and characterization of amine-functionalized SiO2/TiO2 films for formaldehyde degradation

This paper investigated the gaseous formaldehyde degradation by the amine-functionalized SiO₂/TiO₂ photocatalytic films for improving indoor air quality. The films were synthesized via the co-condensation reaction of methyltrimethoxysilane (MTMOS) and 3-aminopropyltrimethoxysilane (APTMS). The physicochemical properties of prepared photocatalysts were characterized with N₂ adsorption/desorption isotherms measurement, X-ray diffraction (XRD) and Fourier Transform Infrared spectroscopy (FT/IR). The effect of amine-functional groups and the ratio of MTMOS/APTMS precursors on the formaldehyde adsorption and photocatalytic degradation were investigated. The results showed that the formaldehyde adsorption and photocatalytic degradation of the APTMS-functionalized SiO₂/TiO₂ film was higher than that of SiO₂/TiO₂ film due to the surface adsorption on amine sites and the relatively high of the specific surface area of the APTMS-functionalized SiO₂/TiO₂ film (15 times higher than SiO₂/TiO₂). The enhancement of the formaldehyde degradation of the film can be attributed to the synergetic effect of adsorption and subsequent photocatalytic decomposition. The repeatability of photocatalytic film was also tested and the degradation efficiency was 91.0% of initial efficiency after seven cycles.     

Enhanced nonlinear optical absorption of Au/SiO2 nano-composite thin films

Nano metal-particle dispersed glasses are the attractive candidates for nonlinear optical material applications.Au/SiO 2 nano-composite thin films with 3 vol% to 65 vol% Au are prepared by inductively coupled plasma sputtering.Au particles as perfect spheres with diameters between 10 nm and 30 nm are uniformly dispersed in the SiO 2 matrix.Optical absorption peaks due to the surface plasmon resonance of Au particles are observed.The absorption property is enhanced with the increase of Au content,showing a maximum value in the films with 37 vol% Au.The absorption curves of the Au/SiO 2 thin films with 3 vol% to 37 vol% Au accord well with the theoretical optical absorption spectra obtained from Mie resonance theory.Increasing Au content over 37 vol% results in the partial connection of Au particles,whereby the intensity of the absorption peak is weakened and ultimately replaced by the optical absorption of the bulk.The band gap decreases with Au content increasing from 3 vol% to 37 vol % but increases as Au content further increases.     

由纳米管和纳米颗粒构成的TiO2膜的制备与机理研究

采用聚苯乙烯小球修饰Ti片表面,并进行阳极氧化,制备出一种由纳米颗粒和纳米管构成的TiO₂膜．通过数值模拟,分析了氧化表面附近的局部电场分布对TiO₂膜形貌的影响．结果表明,覆盖物增强了局部电场,从而加快了O^2-与Ti的反应速率,有利于TiO₂的生长;与此同时,[TiF₆]^6-的扩散受到阻碍,使得TiO₂的溶解速率减慢．可见,覆盖物打破了TiO₂纳米管形成的平衡条件,导致纳米颗粒的生成．此外,通过X射线衍射和Raman光谱的测试分析发现,所制备的TiO₂为锐钛矿结构.     

Substrate effects on the oxygen gas sensing properties of SnO2/TiO2 thin films

In this study, SnO₂/TiO₂ thin films are fabricated on SiO₂/Si and Corning glass 1737 substrates using a R.F. magnetron sputtering process. The gas sensing properties of these films under an oxygen atmosphere with and without UV irradiation are carefully examined. The surface structure, morphology, optical transmission characteristics, and chemical compositions of the films are analyzed by atomic force microscopy, scanning electron microscopy and PL spectrometry. It is found that the oxygen sensitivity of the films deposited on Corning glass 1737 substrates is significantly lower than that of the films grown on SiO₂/Si substrates. Therefore, the results suggest that SiO₂/Si is an appropriate substrate material for oxygen gas sensors fabricated using thin SnO₂/TiO₂ films.     

Methylene blue photoelectrodegradation under UV irradiation on Au/Pd-modified TiO2 films

In this work TiO₂ thin films were modified with gold/palladium (Au/Pd) bimetallic paticles by sputtering method. TiO₂ films were deposited on ITO (SnO₂:In) by Doctor Blade method and post-anneling. The properties of the films were studied through measurements of XRD (X-ray diffraction) and AFM (atomic force microscopy). The degradation of methylene blue was studied by UV-irradiated pure TiO₂ and Au/Pd-modified TiO₂ in aqueous solution. Langmuir-Hinshelwood model was used to obtain kinetic information. Photocatalytic study indicated that Au/Pd-modified TiO₂ photocatalytic activity was better than TiO₂ pure; the best half-life time for Au/Pd-modified TiO₂ in photodegradation was 2.8 times smaller than TiO₂ pure; finally the efficiency in methylene blue photodegradation was improved from 23% to 43% when Au/Pd-modified TiO₂ films were used.