La0.3Sr0.7TiO3模板层对Pb(Zr0.5Ti0.5)O3薄膜的铁电性能增强效应的研究

通过sol-gel法在Si (111) 基片上分别制备了LaNiO₃(LNO)底电极和LaNiO₃/La_0.3Sr_0.7TiO₃ (LNO/LSTO)底电极.然后采用sol-gel 方法，在两种衬底上分别制备了Pb (Zr_0.5Ti_0.5)O₃ (PZT)铁电薄膜.XRD分析表明，两种PZT薄膜均具有钙钛矿结构，且在LNO底电极上的PZT薄膜呈(100) 择优取向，而在LNO/LSTO底电极上的PZT薄膜呈随机取向.铁电性能测试表明，相对LNO衬底上制备的PZT薄膜，在LNO/LSTO底电极上制备的PZT薄膜的剩余极化强度得到了有效的增强，同时矫顽场也增大.介电常数和漏电流的测试表明，LNO/LSTO底电极上制备的PZT薄膜具有大的介电常数和漏电流. 关键词： PZT薄膜 铁电性 漏电流 0.3Sr_0.7TiO₃')" href="#">La_0.3Sr_0.7TiO₃     

氧压对SrTiO3和SrNb0.2Ti0.8O3薄膜晶格参数的影响及激光感生热电电压效应

采用脉冲激光沉积技术制备了SrTiO₃和SrNb_0.2Ti_0.8O₃薄膜.X射线衍射分析表明在LaAlO₃(100)单晶平衬底上生长的SrTiO₃及SrNb_0.2Ti_0.8O₃薄膜是沿［001］取向的近外延生长.随着氧压在一定范围内逐渐增大,SrTiO₃薄膜的晶格参数减小,而SrNb_0.2Ti_0.8O₃薄膜的晶格参数先减小后增大.同时摸索出制备具有二维电子气超晶格(SrTiO₃/SrNb_0.2Ti_0.8O₃)_L的最佳氧压为1.0×10^-2Pa.另外在LaAlO₃(100)倾斜衬底上制备的SrNb_0.2Ti_0.8O₃薄膜中观察到激光感生热电电压效应. 关键词： 0.2Ti_0.8O₃薄膜')" href="#">SrNb_0.2Ti_0.8O₃薄膜 晶格参数 激光感生热电电压 脉冲激光沉积     

不同衬底上Pb(Zr0.52Ti0.48)O3择优取向铁电薄膜的制备和研究

通过MOD法在Si(100)和Pt(111)/Ti/SiO₂/Si基片上制备出LaNiO₃ ( LNO)薄膜.再通过修 正的Sol-gel法，在Pt(111)/Ti/SiO₂/Si,LNO/Si(100)和LNO/Pt/Ti/SiO_{2< /sub>/Si三种衬底上 制备出具有择优取向的Pb(Zr0.52Ti0.48)O3铁电薄膜. 经XRD分析表明，L NO薄膜具有(100)择优取向的类钙钛矿结构；PZT薄膜均具有钙钛矿结构，且在Pt(111)/Ti/S iO2/Si衬底上的薄膜以(110)择优取向，在LNO/Pt/Ti/SiO2/Si和LN O/Si(100)衬底上的 薄膜以(100)择优取向.经场发射SEM分析和介电、铁电性能测试表明，在LNO/Si和LNO/Pt/Ti /SiO2/Si衬底上的PZT薄膜的平均粒径、介电常数以及剩余极化强度均比以Pt/T i/SiO2/Si为衬底的薄膜大. 关键词： 3}薄膜')" href="#">LaNiO₃薄膜 PZT铁电薄膜 择优取向 剩余极化强度     

低电场下LiNbO3薄膜在非晶衬底上的取向生长

报道了外加低电场和衬底温度对脉冲激光淀积法制备的LiNbO₃薄膜取向的影响.在衬底温度为600℃和外加电场为7V/cm的条件下，在石英玻璃等非晶态衬底上获得了完全(001)取向的LiNbO₃薄膜.在对具有自发极化的LiNbO₃在电场作用下成核生长机制和温度对LiNbO₃自发极化强度的影响进行分析的基础上，给出了低电场诱导铁电薄膜取向生长的物理依据. 关键词：     

PbTiO3/PbZr0.3Ti0.7O3/PbTiO3夹心结构铁电薄膜子晶层的优化

用Sol-Gel法制备了Pb_(1+x)TiO₃/PbZr_03Ti_07O₃/Pb_(1+x)TiO₃(PT/PZT/PT)夹心结构及PZT铁电薄膜,为了获得高质量的PT/PZT/PT夹心结构铁电薄膜,使用不同过量Pb配比(x)的PbTiO₃ (PT)层进行制备,以获得优化的PT子晶层.X射线 关键词： PT/PZT/PT 夹心结构 子晶 铁电薄膜     

用激光分子束外延在玻璃衬底上生长La0.67Sr0.33MnO3薄膜

采用激光分子束外延技术,在玻璃衬底上制备了La_067Sr_033MnO₃ （LSMO） 薄膜,X射线衍射测量结果表明在玻璃衬底上生长的LSMO薄膜沿c轴择优取向生长.在外磁场3 T和88, 220, 300 K条件下,LSMO薄膜的磁电阻变化率分别达到-378%, -268%和-607%.实验结果表明,在廉价的玻璃衬底上制备大面积和具有应用价值的锰氧化物薄膜是可行的. 关键词： 锰氧化物薄膜 玻璃衬底 外延生长     

La0.5Sr0.5CoO3薄膜的外延生长及其机理研究

利用脉冲激光制膜法,在多种衬底和温度条件下,系统研究了La_0.5Sr_0.5CoO₃(LSCO)薄膜的结构和外延生长特性,在LaAlO₃,SrTiO₃和MgO衬底上实现了LSCO薄膜的外延生长.外延生长的薄膜具有低的电阻率和金属性导电特征.研究表明,外延生长的最佳温度范围为700—800℃,最佳衬底为LaAlO₃.并着重探讨了衬底材料和淀积温度等多种因素对LSCO薄膜的生长与性 关键词：     

Ag掺杂的La0.67Pb0.33MnO3薄膜中激光感生热电电压效应

采用脉冲激光沉积法在倾斜LaAlO₃衬底上制备了Ag掺杂的La_0.67Pb_0.33MnO₃(LPMO)系列薄膜，发现该类薄膜中有激光感生热电电压(LITV)效应.随着掺Ag量x(x为Ag的质量与LPMO的质量之比)从0.00增加到0.10，LPMO薄膜中的LITV信号的响应时间先递减后递增，但始终小于未掺Ag的薄膜，掺Ag量x=0.06时响应时间最小.研究发现LPMO薄膜存在一个最佳厚度，在这一厚度下可使得LITV信号 关键词： 3薄膜')" href="#">LaPbMnO₃薄膜 激光感生热电电压 各向异性Seebeck系数 响应时间     

Bi0.8Ba0.2FeO3/La0.7Sr0.3MnO3异质结制备及其交换偏置效应研究

采用脉冲激光沉积方法, 通过调节激光能量、激光频率、衬底温度、氧压、靶基距等工艺参数, 在(100)取向的铝酸镧单晶衬底上制备出Bi_0.8Ba_0.2FeO₃/La_0.7Sr_0.3MnO₃多铁性异质结. X射线衍射图谱表明薄膜呈钙钛矿结构, 高分辨透射电镜图谱和能量色散X射线图谱表明两相界面清晰且具有良好的匹配度, 异质结呈(00l)取向性生长. 加场冷却条件下不同温度的磁滞回线(M-H)测量结果表明样品具有明显的交换偏置效应, 交换偏置场(H_EB)随温度的线性变化可能与异质结界面处电子轨道的重构和界面处自旋、轨道自由度之间的复杂的相互作用有关.     

激光分子束外延BaTiO3薄膜最顶层表面原子平面与薄膜生长机理

用激光分子束外延技术在SrTiO₃(001)衬底上外延生长了高质量的BaTiO_{3< /sub>薄膜,薄膜的生长过程由反射式高能电子衍射仪(RHEED)原位实时监测,表明薄膜具有 二维层状生长模式.薄膜的晶体结构和表面形貌分别由X射线衍射和原子力显微镜表征,显示 该薄膜为完全c轴取向四方相晶体结构,其表面具有原子尺度光滑性.采用角分辨X射线光电 子谱技术(ARXPS),研究了BaTiO3薄膜表面最顶层原子种类和排列状况.结果表 明,BaTiO3 关键词： 激光分子束外延 3薄膜')" href="#">氧化物BaTiO3薄膜 最顶层表面 角分辨X射线光电子谱}     

Effects of crystallinity on laser-induced voltage effect from Zn0.9Co0.1O thin film

Co-doped ZnO epilayer films were grown by pulsed laser deposition (PLD) on vicinal cut silicon and sapphire substrates. Changes in deposition time were observed as a moderate effect on the quality of the films, and the influence of the thickness on thermoelectric signals from Zn_0.9Co_0.1O thin films were discussed. The effect of one of the main deposition parameters, the deposition time, on the crystallinity and electron mobility properties of the Zn_0.9Co_0.1O thin films grown on sapphire was investigated by means of X-ray diffraction (XRD) and laser-induced voltage (LIV) effect. It shown that the XRD rocking curve full-width half-maximun (FWHM) decreased as time increasing, and the LIV signals were observed along the tilting angle of the substrate orientation when the pulsed KrF excimer laser of 248 nm were irradiated on the films. When the films illuminated in pulse lasers, the highest signals occurred in the films with best crystalline quality, and the signals were higher in the films grown on sapphire than those on silicon substrates. It suggested that the electrical resistivity and electron mobility have close relations with not only the crystallinity but also with the interface of the thin films.     

Electrical transport properties and laser-induced voltage effect in La0.8Ca0.2MnO3 epitaxial thin films

La_0.8Ca_0.2MnO₃ (LCMO) thin films about 200 nm thickness were grown on untilted and tilted (5°, 10° and 15°) LaAlO₃ (100) single crystal substrates by pulsed laser deposition technique. Electrical properties of the epitaxial thin films were studied by conventional four-probe technique and the anisotropic thermoelectric properties of the films grown on the tilted substrates have been investigated by laser-induced voltage (LIV) measurements. X-ray diffraction analysis and atomic force microscopy results show that the prepared LCMO thin films have a single phase and high crystalline quality. The remarkably large temperature coefficient of resistance (TCR) values (above 11 %/K) are observed in the all films. TCR value reaches 18 %/K on the film grown on 10° tilted substrate. The intensity of LIV signals monotonously increases with the tilting angles, and the largest signal is 148 mV with the fast time response 229 ns for the film grown on 15° tilted substrate.     

外加电场对铁电薄膜相变的影响

采用热力学非线性理论,研究了外加电场对立方基底Pb(Zr_0.3Ti_0.7)O₃(PZT)铁电薄膜相变的影响.通过数值计算,得到了"失配应变-外加电场"相图,及外加电场与极化强度的关系.当外加电场达到186 kV/cm时,能使生长在SrTiO₃ 基底上PZT铁电薄膜从单斜r相转变为c相.在实验上,采用扫描探针显微镜通过对PZT薄膜施加不同的极化电场来研究了它的电畴翻转.从得到的压电响应相图可以看出,绝大多数的电畴是清晰可 关键词： 铁电薄膜 相变 扫描探针显微镜 失配应变     

Transverse laser induced thermoelectric voltage effect in tilted La0.5Sr0.5CoO3 thin films

The transverse laser induced thermoelectric voltage effect has been investigated in tilted La_0.5Sr_0.5CoO₃ thin films grown on vicinal cut LaAlO₃ (1 0 0) substrates when films are irradiated by pulse laser at room temperature. The detected voltage signals are demonstrated to originate from the transverse Seebeck effect as the linear dependence of voltage on tilted angle in the range of small tilted angle. The Seebeck coefficient anisotropy ΔS of 0.03 μV/K at room temperature is calculated and its distorted cubic structure is thought to be responsible for this. Films grown on a series of substrates with different tilted angles show the optimum angle of 19.8° for the maximum voltage. Film thickness dependence of voltage has also been studied.     

Role of crystal orientation on the magnetic properties of CoFe2O4 thin films grown on Si (1 0 0) and Al2O3 (0 0 0 1) substrates using pulsed laser deposition

We report the influence of crystal orientation on the magnetic properties of CoFe₂O₄ (CFO) thin films grown on single crystal Si (1 0 0) and c-cut sapphire (Al₂O₃) (0 0 0 1) substrates using pulsed laser deposition technique. The thickness was varied from 200 to 50 nm for CFO films grown on Si substrates, while it was fixed at 200 nm for CFO films grown on Al₂O₃ substrates. We observed that the 200 and 100 nm thick CFO-Si films grew in both (1 1 1) and (3 1 1) directions and displayed out-of-plane anisotropy, whereas the 50 nm thick CFO-Si film showed only an (1 1 1) orientation and an in-plane anisotropy. The 200 nm thick CFO film grown on an Al₂O₃ substrate was also found to show a complete (1 1 1) orientation and a strong in-plane anisotropy. These observations pointed to a definite relation between the crystalline orientation and the observed magnetic anisotropy in the CFO thin films.     

Comparison of the effect of PLT and PZT buffer layers on PZT thin films for ferroelectric materials applications

In order to study the effect of different buffer layers on the Pb(Zr_0.52Ti_0.48)O₃ (PZT) thin films, 10-nm thick (Pb_0.72La_0.28)Ti_0.93O₃ (PLT) and Pb(Zr_0.52Ti_0.48)O₃ buffer layers have been deposited on the Pt(1 1 1)/Ti/SiO₂/Si substrates by pulsed laser deposition, respectively. The top buffer layers were also deposited on PZT thin films with the same thickness of the seed layers in order to enhance the fatigue characteristics of PZT thin films. We compared the results of dielectric constant, hysteresis loops and fatigue resistance characteristics. It was found that the dielectric properties of PZT thin films with PLT buffer layers were improved by comparing with PZT thin films with PZT buffer layers. The polarization characteristics of PZT thin films with PLT buffer layers were observed to be superior to those of PZT thin films using PZT buffer layers. The remanent polarization of PZT thin films showed 36.3 μC/cm² and 2.6 μC/cm² each in the case of use PLT and PZT buffer layers. For the switching polarization endurance analysis, PZT thin films with PLT buffer layers showed more excellent result than that of PZT thin films with PZT buffer layers.     

Laser-induced voltage characteristics of Bi2Sr2Co2Oy thin films on LaAlO3 substrates

We report the laser-induced voltage (LIV) effects in c-axis oriented Bi₂Sr₂Co₂O_y thin films grown on (0 0 1) LaAlO₃ substrates with the title angle α of 0°, 3°, 5° and 10° by a simple chemical solution deposition method. A large open-circuit voltage with the sensitivity of 300 mV/mJ is observed for the film on 10° tilting LaAlO₃ under a 308 nm irradiation with the pulse duration of 25 ns. When the film surface is irradiated by a 355 nm pulsed laser of 25 ps duration, a fast response with the rise time of 700 ps and the full width at half maximum of 1.5 ns is achieved. In addition, the experimental results reveal that the amplitude of the voltage signal is approximately proportional to sin 2α and the signal polarity is reversed when the film is irradiated from the substrate side rather than the film side, which suggests the LIV effects in Bi₂Sr₂Co₂O_y thin films originate from the anisotropic Seebeck coefficient of this material.     

Study on the properties of Pb(Zr,Ti)O3 thin films grown alternately by pulsed laser deposition and sol-gel method

In order to prepare good quality Pb(Zr,Ti)O₃ (PZT) thin films, we consider the method of alternately growing PZT thin films on Pt (111)/Ti/SiO₂/Si (100) substrates by pulsed laser deposition (PLD) and sol-gel. In this work, we conducted comparative experiments on different film preparation methods, and 1.0 um thick PZT film was grown on platinized silicon wafers by an alternate PLD and sol-gel method. The microstructure and electrical properties of the films is analyzed. Through the study of X-ray diffraction, SEM, AFM, PFM, and ferroelectric testing, it is found that the alternating growth of a film by the alternate PLD and sol-gel method has good compactness, excellent ferroelectric properties, and smaller leakage current compared to film prepared by the sol-gel method alone.     

Highly (100) oriented Pb(Zr<Subscript>0.52</Subscript>Ti<Subscript>0.48</Subscript>)O<Subscript>3</Subscript>/LaNiO<Subscript>3</Subscript> films grown on amorphous substrates by pulsed laser deposition

Pb(Zr_0.52Ti_0.48)O₃ (PZT)/LaNiO₃ (LNO) thin films with highly (100) out of plane orientation were produced on SiO₂/Si(100) and alkaline earth aluminosilicate glass substrates by pulsed laser deposition (PLD). Orientations of both PZT and LNO films were evaluated using X-ray diffraction. The pure (100)-oriented PZT/LNO films were obtained under optimized deposition conditions. Time of flight-secondary ion mass spectrometry analysis showed that LNO could effectively block interdiffusion between the PZT films and the substrates. Fairly smooth surfaces of the PZT films with roughness of about 4 nm were observed using an atomic force microscope. Cross sectional examination revealed that the films grew in columnar grains. The PZT films grown on both SiO₂/Si and glass substrates demonstrated very good ferroelectric characteristic at room temperature with remnant polarization of up to 26 μC/cm². PACS 79.20.DS; 77.84.DY; 78.70.Ck     

Laser-induced voltage (LIV) enhancement of La2/3Sr1/3MnO3 films with Ag addition

La_2/3Sr_1/3MnO₃:Ag _x (LSMO:Ag _x , x=0, 0.04, 0.08, 0.10, 0.20, 0.30) films were grown on vicinal cut LaAlO₃ (LAO) substrates by pulsed laser deposition technique (PLD). It is found that laser-induced voltage (LIV) of LSMO:Ag _x films is improved and enhanced by Ag addition. With x increasing, figure of merit (F _m ) and anisotropic Seebeck coefficient (ΔS) of LSMO:Ag _x (x=0.08) films reach the maximum values of 28.25 mV/ns and 0.38 μV/K, respectively. The results suggest that the LIV enhancement of LSMO:Ag _x films is due to the anisotropy of the Seebeck tensor, which is produced by long range cooperative Jahn–Teller distortions with Ag addition.