Microwave‐Assisted Free Radical Polymerizations and Copolymerizations of Styrene and Methyl Methacrylate

Summary: Radical homopolymerizations and copolymerizations of styrene were performed in toluene and N,N‐dimethylformamide (DMF) as solvents using different initiators with and without microwave irradiation. Only the homopolymerization of styrene under microwave irradiation in DMF with DtBP showed significantly enhanced styrene conversion whereas other initiators resulted in no or only slight increase of styrene conversion under microwave irradiation. In any case, DMF was required to gain in styrene conversion under microwave irradiation. Significantly higher monomer conversions were observed under otherwise comparable conditions in the copolymerization of styrene and methyl methacrylate (MMA) in DMF. Microwave‐induced selectivity of monomers was not observed in copolymerizations.

Yield of styrene polymerizations under varying reaction conditions initiated by DtBP.     

Copolymerization of ethylene with styrene catalyzed by a linked bis(phenolato) titanium catalyst

Copolymerization of ethylene with styrene, catalyzed by 1,4‐dithiabutanediyl‐linked bis(phenolato) titanium complex and methylaluminoxane, produced exclusively ethylene–styrene copolymers with high activity. Copolymerization parameters were calculated to be r_E = 1.2 for ethylene and r_S = 0.031 for styrene, with r_E r_S = 0.037 indicating preference for alternating copolymerization. The copolymer microstructure can be varied by changing the ratio between the monomers in the copolymerization feed, affording copolymers with styrene content up to 68%. The copolymer microstructure was fully elucidated by ¹³C NMR spectroscopy revealing, in the copolymers with styrene content higher than 50%, the presence of long styrene–styrene homosequences, occasionally interrupted by isolated ethylene units. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1908–1913, 2006     

Composition and Microstructure Determination of the Syndiotactic Copolymer of para-Methylstyrene and Styrene by Pyrolysis Gas Chromatography

The composition and microstructure of syndiotactic para-methylstyrene/styrene copolymer was determined by a pyrolysis gas chromatography (Py-GC) method. This method uses the styrene and para-methylstyrene monomer peak intensities to determine the styrene and para-methylstyrene composition in the copolymer. The number average sequence length of styrene was calculated by using the triad peak intensities. Because of the low concentration of para-methylstyrene in the copolymer, the number average sequence length of para-methylstyrene was determined with formulas that incorporate the copolymer composition and the number average sequence length of styrene. The distribution of para-methylstyrene defined by the terms “percent of single units” and “percent of desired distribution” was calculated by the number average sequence of para-methylstyrene. This method has been tested with copolymers containing up to 24 mole% of para-methylstyrene. The composition results from Py-GC of para-methylstyrene and styrene copolymers used in this study were in excellent agreement with ¹H-NMR results.     

Grafting of poly(styrene‐co‐p‐chloromethyl styrene) with ethyl methacrylate via atom transfer radical polymerization catalyzed by CuCl/1,2‐dipiperidinoethane

Poly(styrene‐graft‐ethyl methacrylate) graft copolymer was prepared by atom transfer radical polymerization (ATRP) with poly(styrene‐co‐p‐chloromethyl styrene)s in various compositions as macroinitiator in the presence of CuCl/1,2‐dipiperidinoethane at 130 °C in N,N‐dimethylformamide. Both macroinitiators and graft copolymers were characterized by elemental analysis, IR, ¹H and ¹³C NMR, and differential scanning calorimetry. 1,2‐Dipiperidinoethane was an effective ligand of CuCl for ATRP in the graft copolymerization. The controlled growth of the side chain provided the graft copolymers with polydispersities of 1.60–2.05 in the case of poly(styrene‐co‐p‐chloromethyl styrene) (62:38) macroinitiator. Thermal stabilities of poly(styrene‐graft‐ethyl methacrylate) graft copolymers were investigated by thermogravimetric analysis as compared with those of the macroinitiators. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 668–673, 2003     

Study of energy transfer to solvent in radiation graft polymerization of styrene onto polyethylene

The radiation-initiated graft polymerization of styrene onto polyethylene was studied to determine whether energy transfer to diluent was responsible for the previously observed high orders of dependence of the grafting rate on monomer concentration. n-Octane was used as the diluent instead of benzene. If energy transfer from excited polyethylene to benzene were present, it should not be with n-octane. The percent swelling of polyethylene by various n-octane–styrene mixtures was determined. The compositions of various n-octane–styrene mixtures absorbed inside polyethylene were determined by ultraviolet and refractive index measurements and found to be richer in styrene than the corresponding mixtures in which the polyethylene had been placed. The graft polymerization rates were determined at 0.000761, 0.0371, and 0.213 Mrad/hr and plotted against the inside styrene concentrations on a log-log scale to yield the kinetic orders of dependence of rate on monomer as 2,3, and 3, respectively. It was concluded that energy transfer to diluent was not responsible for the high-order dependence observed.     

Synthesis and characterization of ABA‐type amphiphilic tri‐block copolymers through anionic polymerization using end functionalized poly(ethylene oxide) oligomers

ABA‐type amphiphilic tri‐block copolymers were successfully synthesized from poly(ethylene oxide) derivatives through anionic polymerization. When poly(styrene) anions were reacted with telechelic bromine‐terminated poly(ethylene oxide) ( 1 ) in 2:1 mole ratio, poly(styrene)‐b‐poly(ethylene oxide)‐b‐poly(styrene) tri‐block copolymers were formed. Similarly, stable telechelic carbanion‐terminated poly(ethylene oxide), prepared from 1,1‐diphenylethylene‐terminated poly (ethylene oxide) ( 2 ) and sec‐BuLi, was also used to polymerize styrene and methyl methacrylate separately, as a result, poly (styrene)‐b‐poly(ethylene oxide)‐b‐poly(styrene) and poly (methyl methacrylate)‐b‐poly(ethylene oxide)‐b‐poly(methyl methacrylate) tri‐block copolymers were formed respectively. All these tri‐block copolymers and poly(ethylene oxide) derivatives, 1 and 2 , were characterized by spectroscopic, calorimetric, and chromatographic techniques. Theoretical molecular weights of the tri‐block copolymers were found to be similar to the experimental molecular weights, and narrow polydispersity index was observed for all the tri‐block copolymers. Differential scanning calorimetric studies confirmed the presence of glass transition temperatures of poly(ethylene oxide), poly(styrene), and poly(methyl methacrylate) blocks in the tri‐block copolymers. Poly(styrene)‐b‐poly(ethylene oxide)‐b‐poly(styrene) tri‐block copolymers, prepared from polystyryl anion and 1 , were successfully used to prepare micelles, and according to the transmission electron microscopy and dynamic light scattering results, the micelles were spherical in shape with mean average diameter of 106 ± 5 nm. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Bio‐based copolymers obtained through miniemulsion copolymerization of methyl esters of acrylated fatty acids and styrene

Polymers based on renewable sources are promising materials, and can find many uses in coatings and adhesive applications. The goal of this work was to synthesize and characterize bio‐based styrene/acrylated fatty acid methyl ester (AFAME) copolymer—poly(styrene‐co‐AFAME) prepared by miniemulsion polymerization. The main strategy adopted was to functionalize the bio‐monomer with acrylic acid that was confirmed by ¹H NMR and FTIR measurements, to allow its free‐radical homo‐ or copolymerization with styrene. Poly(styrene‐co‐AFAME) with different AFAME content were obtained and their composition were evaluated by ¹H NMR. Dynamic light scattering measurements throughout the reactions have indicated a very stable colloidal systems and average particles size ranges 100–150 nm. The structural and physical properties of poly(styrene‐co‐AFAME) were investigated by DTG‐DTA, DSC which displayed a decreasing of glass transition temperature with increase of AFAME content. The results showed in this study have indicated that the poly(styrene‐co‐AFAME) can be used in several fields because their characteristics are totally distinct. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 1422–1432     

Reactivity of ester groups on insoluble polymer supports

A study was made of the comparative rates of reaction of active ester functional groups (p-nitrophenyl and 2,4-dinitrophenyl esters) situated on three types of insoluble support polymers and on small, soluble analogs of the polymer molecules. The supports consisted of a styrene—divinylbenzene bead-type polymer (2% DVB), a styrene—divinylbenzene popcorn polymer (0.2% DVB), and a popcorn polymer with 2,3-dimethylbutadiene and substituted styrene units in the chain. p-Nitrophenyl benzoate and 2,4-dinitrophenyl p-isopropylbenzoate were used as soluble analogs. Rates of aminolysis by small molecules (2-aminoethanol and n-tetradecylamine) in pyridine and of solvolysis in alcohols catalyzed by both small (N-methylimidazole) and large (polyvinylimidazole) molecules were determined. With the small amines, finely divided particles of popcorn and bead type styrene polymers reacted at about the same rate, which was approximately 1/5 the rate of reaction of the homogeneous analogs. With a high molecular weight reagent, polyvinylimidazole, the heterogeneous reactions were much slower and the popcorn polymer reacted faster than the bead polymer. In catalyzed solvolyses, the styrene popcorn derivative reacted faster in benzyl alcohol and slower in 1-hexanol than the dimethylbutadiene popcorn polymer derivatives.     

Dynamic mechanical properties of two copolymers of styrene and n-hexyl methacrylate

The storage (J′) and loss (J″) shear compliances have been measured for two random copolymers of styrene and n-hexyl methacrylate with styrene contents of 18% and 30% (by weight) in the frequency range 45–4400 Hz and the temperature range 31–107°C. The data at different temperatures were combined by the method of reduced variables, and the WLF coefficients were calculated from the temperature shift factors by the method of Pierson and Kovacs. The data were compared with earlier data for the two homopolymers. The thermal expansion coefficient of the fractional free volume, and the free volume at the glass transition temperature, varied monotonically with composition, but the fractional free volume at a reference temperature of 100°C appeared to pass through a maximum as a function of concentration. Comparison of isothermal plots of J′ at 100°C, plots of the relaxation spectrum at 100°C, the monomer friction coefficient and its temperature dependence, and isochronal plots of the storage shear moduls at 100 radians/see all show that the properties of poly(n-hexyl methacrylate) are very slightly affected by incorporation of 18% styrene and only moderately affected by 30% styrene. By contrast, comparison of styrene–butadiene rubber with 1,4-polybutadiene shows a very large effect of incorporation of 23.5% styrene. These differences may be associated with local packing relations of the comonomer residues and suggest that copolymer properties cannot be readily predicted from those of the component homopolymers.     

Polymers containing fluorinated ketone groups. III. Synthesis of styrene/p-vinyltrifluoroacetophenone copolymers by modification of polystyrene and the copolymerization of monomers

Copolymers of styrene/p-vinyltrifluoroacetophenone were prepared by two different reaction routes: (1) modification of polystyrene with trifluoroacetyl chloride and (2) copolymerization of styrene and p-vinyltrifluoroacetophenone (VTFA). There appears to be a limit to the modification method because only a maximum content of 14.5 mole % trifluoroacetyl functionality could be attached to the polymer before the onset of crosslinking. Differential scanning calorimetry (DSC) was used to determine their T_g's. In addition, the reactivity ratios of styrene and VTFA were investigated. The reactivity ratios and Q and e values were r₁ = 0.30 ± 0.09 (styrene) and r₂ = 1.3 ± 0.3 (VTFA); Q₁ = 1.0 and e₁ = ?0.8 (styrene); Q₂ = 0.44 and e₂ = 1.93 (VTFA).     

Simultaneous determination of the styrene unit content and assessment of molecular weight of triblock copolymers in adhesives by a size exclusion chromatography method

The content of styrene units in nonhydrogenated and hydrogenated styrene‐butadiene‐styrene and styrene‐isoprene‐styrene triblock copolymers significantly influences product performance. A size exclusion chromatography method was developed to determine the average styrene content of triblock copolymers blended with tackifier in adhesives. A complete separation of the triblock copolymer from the other additives was realized with size exclusion chromatography. The peak area ratio of the UV and refraction index signals of the copolymers at the same effective elution volume was correlated to the average styrene unit content using nuclear magnetic resonance spectroscopy with commercial copolymers as standards. The obtained calibration curves showed good linearity for both the hydrogenated and nonhydrogenated styrene‐butadiene‐styrene and styrene‐isoprene‐styrene triblock copolymers (r  = 0.974 for styrene contents of 19.3–46.3% for nonhydrogenated ones and r  = 0.970 for the styrene contents of 23–58.2% for hydrogenated ones). For copolymer blends, the developed method provided more accurate average styrene unit contents than nuclear magnetic resonance spectroscopy provided. These results were validated using two known copolymer blends consisting of either styrene‐isoprene‐styrene or hydrogenated styrene‐butadiene‐styrene and a hydrocarbon tackifying resin as well as an unknown adhesive with styrene‐butadiene‐styrene and an aromatic tackifying resin. The methodology can be readily applied to styrene‐containing polymers in blends such as poly(acrylonitrile‐butadiene styrene).     

Effect of substituents in the styrene ring on the dynamic mechanical relaxations of a styrene-crosslinked unsaturated polyester resin

The dynamic mechanical properties of a series of polyester resins made from a maleic/phthalic anhydride-based unsaturated polyester crosslinked with each of styrene, 4-methyl styrene, 4-ethyl styrene, 4-n-butyl styrene, 4-isopropyl styrene, tertiary butyl styrene, 4-chlorostyrene, and 3,4-dichlorostyrene were studied. The order of the α transition temperatures was as expected from that for the homopolymers, except in the case of the chlorostyrenes, for which dipolar interactions with the polyester chain may be important. The styrene bridges appeared to be involved in a steric interaction (and in the case of the chlorostyrenes, a dipolar interaction) with the β relaxing ester species. It is suggested that both the γ and γ′ relaxations involve similar interactions between the matrix and the relaxing moieties. For the 4-n-butyl styrene resin, an additional relaxation below ?170°C was observed, and is ascribed to relaxation of the n-butyl group.     

Preparation of triblock styrene–tert-butylstyrene–styrene copolymers by living radical polymerization with a heterogeneous polymeric initiator

Triblock copolymers containing the sequence styrene, p-tert-butylstyrene, styrene were prepared in an emulsion system by using isotactic polypropylene hydroperoxide as the initiator together with triethylenetetramine as an activator, according to the method of Mikulasova and co-workers. Polymerization of styrene continued after removal of the initiator from the emulsion by filtration and eventually reached 100% conversion after 4 hr at 35°C. tert-Butylstyrene at 80°C and styrene at 35°C were added successively to the system, with each polymerization reaction carried to 100% conversion before the next monomer was added. Thin-layer chromatography was used to separate the homopolymers and block copolymers in order to determine the purity of the product. Monomer compositions of the block copolymers was verified by infrared analysis. The existence of two separate phases in the extracted block copolymer was indicated by the observation of two distinct glass transition temperatures.     

Synthesis of polymeric microspheres from a Merrifield resin by surface‐initiated nitroxide‐mediated radical polymerization

Polymeric microspheres were prepared from a Merrifield resin via nitroxide‐mediated radical polymerization. Polystyrene, poly(acetoxystyrene), and poly[styrene‐b‐(methyl methacrylate‐co‐styrene)], poly(acetoxystyrene‐b‐styrene), and poly(styrene‐co‐2‐hydroxyethyl methacrylate) copolymers were demonstrated to graft onto 2,2,6,6‐tetramethyl‐1‐piperidinyloxy nitroxide bound Merrifield resins. The polymerization control was enhanced both on the surface and in solution by the addition of sacrificial nitroxide. The significant increase in the particle diameter (more than a fivefold volume increase for polystyrene brushes) showed that polymer growth was not only on the surface but also within the particles, and this diameter increase could be adjusted through changes in the molecular weight of the polymers. The microspheres were characterized by elemental analysis, IR spectroscopy, particle size analysis, and optical microscopy. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2145–2154, 2005     

Chiral‐Substrate‐Assisted Stereoselective Epoxidation Catalyzed by H2O2‐Dependent Cytochrome P450SPα

The stereoselective epoxidation of styrene was catalyzed by H₂O₂‐dependent cytochrome P450_SPα in the presence of carboxylic acids as decoy molecules. The stereoselectivity of styrene oxide could be altered by the nature of the decoy molecules. In particular, the chirality at the α‐positions of the decoy molecules induced a clear difference in the chirality of the product: (R)‐ibuprofen enhanced the formation of (S)‐styrene oxide, whereas (S)‐ibuprofen preferentially afforded (R)‐styrene oxide. The crystal structure of an (R)‐ibuprofen‐bound cytochrome P450_SPα (resolution 1.9 Å) revealed that the carboxylate group of (R)‐ibuprofen served as an acid–base catalyst to initiate the epoxidation. A docking simulation of the binding of styrene in the active site of the (R)‐ibuprofen‐bound form suggested that the orientation of the vinyl group of styrene in the active site agreed with the formation of (S)‐styrene oxide.     

Syntheses and reactions of functional polymers. XCIII. Syntheses of polymers containing the N-(4-hydroxy-3-nitrophenyl)succinimide structure in the chain and the use of these activated polymer esters of N-blocked amino acids or peptides

Polymers containing the N-(4-hydroxy-3-nitrophenyl)succinimide residue were designed in order to achieve acyl activation of a reacting carboxylic acid in the solid phase. These polymers were prepared through the following three routes: (a) styrene was allowed to copolymerize with N-(4-hydroxy-3-nitrophenyl)- or N-(4-acetoxy-3-nitrophenyl)maleimide, (b) styrene was copolymerized with N-(4-acetoxyphenyl)maleimide in the presence of divinylbenzene (DVB), and the copolymer obtained was hydrolyzed and nitrated, (c) a copolymer of maleic anhydride and styrene was reacted with p-aminophenol, followed by nitration. The polymers prepared by routes b and c were converted to the activated polymer esters of N-blocked amino acids and peptides by using dicyclohexylcarbodiimide (DCC). The acylated polymers thus obtained were treated with amino acid esters and found to give peptides quantitatively without racemization.     

Radical polymerizability of fumaramide derivatives

Various N-cycloalkyl fumaramides having different characters of N-cycloalkyl groups such as piperidine, morpholine, or pyrrolidone were synthesized and homopolymerized or copolymerized with styrene by use of a radical initiator and ultraviolet irradiation, respectively. N,N′-Dipiperidinyl or -dimorpholyl fumaramides copolymerized with styrene to form a random copolymer, while N,N′-fumaroyl dipyrrolidone tended to form an alternating copolymer with styrene, indicating that the electron distribution of the N-cycloalkyl group affects the polymerizability of fumaramide derivatives. Photopolymerizability of these fumaramides was not as great as that of α,β-unsaturated esters.     

Free-radical polymerization of vinyl ferrocene

The results of quantitative studies of the rates of free-radical polymerization of vinyl ferrocene indicate that the latter has polymerization characteristics similar to those of styrene. The rates of homopolymerization of these two monomers in benzene at 70°C. were measured with the use of azobisisobutyronitrile as catalyst. The rate constants (k = R_p/[M][I]^1/2) are k_VF = (1.1 ? 1.8) × 10^?4, k_STY = 1.65 × 10^?4. Small amounts of vinyl ferrocene and styrene have similar effects on the rates of polymerizations of methyl methacrylate and ethyl acrylate and on the molecular weights of the resulting polymer. Polystyrene and poly(vinyl ferrocene) with similar molecular weights are isolated from polymerizations carried out under identical conditions. The rates of copolymerization of vinyl ferrocene—methyl methacrylate, vinyl ferrocene—styrene, and styrene—methyl methacrylate were determined by following the disappearance of monomers by means of gas chromatographic analyses. The relative reactivity for vinyl ferrocene is slightly lower than that for styrene.     

Solubilization of Styrene and Acrylamide Monomers in Microemulsions

Abstract

Phase diagrams of sodium dodecyl sulfonate (DS)/n‐butanol/styrene/water systems with variable amounts of styrene were constructed at 40°C, and the effects of styrene on microemulsion stability were studied. The solubilization of styrene in these O/W microemulsion systems was investigated by ¹H NMR methods. The results show that the solubilization site shifts from the palisade layer to the inner core of microemulsion droplets when the molar fraction of styrene reaches 0.312. The solubilization of acrylamide in cetyltrimethylmethyl ammonium bromide (CTAB)/n‐butanol/10% n‐octane/water reverse microemulsions (W/O) was studied with a ¹³C NMR method. It was found that the acrylamide was mainly solubilized in the Stern layer of droplets at low acrylamide levels. However, when the mole fraction of acrylamide approaches 0.428, the acrylamide penetrates into the palisade layer and is distributed along the hydrocarbon chain of the surfactant.     

Facile synthesis of blocky styrene(1,3)‐butadiene copolymers having stereoregular monomeric sequences

Half titanocenes (CpCH₂CH₂O)TiCl₂ 1 and (CpCH₂CH₂ OCH₃)TiCl₃ 2 , activated by methylaluminoxane are tested in styrene–1,3‐butadiene copolymerization. The titanocene 1 is able to copolymerize styrene and 1,3‐butadiene, with a facile procedure, to give products with high molecular weight. The analysis of microstructure by ¹³C‐NMR reveals that the styrene homosequences in copolymers are in syndiotactic arrangement, while the butadiene homosequences are, prevailingly, in 1,4‐cis configuration, according with behavior of 1 in the homopolymerizations of styrene and 1,3‐butadiene, respectively. The reactivity ratios of copolymerization are estimated by diad composition analysis. All obtained copolymers have r₁ × r₂ values much larger than 1, indicating blocky nature of homosequences. The structural characterization by wide‐angle X‐ray powder diffraction and differential scanning calorimetry indicates that all copolymers are crystalline, with T_m varying from 171 to 239 °C, depending on the styrene content. The titanocene 2 did not succeed in styrene–1,3‐butadiene copolymerization, giving rise to a blend of homopolymers. Compounds 1 and 2 were also tested in the polymerization of several conjugated dienes, and the obtained results were very useful to rationalize the behavior of both catalysts in the copolymerization of styrene and butadiene. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 815–822, 2010