隔膜和熔融碳酸盐燃料电池 (MCFCS)性能的研究(英文)

用γ LiAO2 粉料和带铸法制备电池隔膜。隔膜有很高的阻窜能力和较低的欧姆极化。在电流密度为 2 0 0和 2 4 6mA/cm2 下放电时 ,用此膜组装的电池组 (三对电池 ,电极面积为 12 2cm2 )输出电压分别为 2 .0 1和 1.78V ,输出功率达 53.4W .于 2 0 0和 30 0mA/cm2 下放电时 ,单电池 (电极面积为 2 8cm2 )输出电压分别高于 0 .85和 0 .75V ,输出功率约 6 .6W .补偿隔膜收缩导致电池性能的提高 .     

1kW熔融碳酸盐燃料电池组研制

1kW熔融碳酸盐燃料电池 (MCFC)组由有效电极面积为 2 4 0mm× 140mm的 30个单电池组成 .系统采用内部分配方式供给气体 ,通过设在电池组底部和四个侧面的电炉丝进行加热 .在常压和 65 0℃条件下 ,分别以氢气和空气作燃料和氧化剂 ,放电电流密度为 15 0mA/cm2 时 ,平均每电池的输出电压达到 0 .7V .在运行的 30 0h内 ,电池组峰值输出功率达到 1.0 6kW .     

200W MCFC电池组的电化学性能及热平衡计算

MCFC电池组 (6对电池 ,电极面积 2 2 6cm2 )在 0 .9MPa/cm2 反应气压下 ,输出功率为2 17.6W .热平衡计算表明 ,该电池组在 30 0mA/cm2 电流密度下放电 ,当气体利用率为 2 0 %时 ,电池组处于热平衡状态下运行 .若维持此热平衡 (电池组内最高温度为 70 0℃ ,运行温度 6 5 0℃ )状态且提高反应气体利用率 ,则电池组热平衡点的电流密度将下降 ,以空气 +CO2 为氧化剂 ,H2 +CO2 为燃料气时 ,在不同气体利用率下电池组热平衡点的电流密度均大于 10 0mA/cm2 .提高电池组的输出功率 ,热电效率将下降 ;提高反应气压 ,热电效率相应提高     

管式电解质支撑型直接碳固体氧化物燃料电池的浸渍法制备及电性能

管状电解质支撑型固体氧化物燃料电池(SOFC)具有稳定性高、电极选择范围广、易封接等优点,很适合应用于直接碳固体氧化物燃料电池(DC-SOFC)现阶段的基础研究中。为实现管状电解质支撑型SOFC的便捷制备,本研究开发了管状YSZ(钇稳定化氧化锆)电解质支撑膜的浸渍法制备工艺。组装了电极材料为Ag-GDC(钆掺杂氧化铈)的电解质支撑型SOFC单电池。测试了单电池分别以加湿氢气和担载5%(w,质量分数)Fe的活性炭为燃料,环境空气为氧化剂的电性能。电池的开路电压接近理论值,且扫描电镜分析结果表明电解质膜致密。单电池以活性碳为燃料在800°C取得了280 m W?cm~(-2)的最大功率密度,接近其以加湿氢气为燃料的330 m W?cm~(-2)。交流阻抗谱结果表明YSZ电解质的欧姆电阻是影响电池性能的主要原因。DC-SOFC以恒电流1 A放电,运行了2.1 h,燃料利用率为36%。DC-SOFC二次装载碳燃料后的电性能几乎与初次的性能一样,表明制备的YSZ电解质支撑膜可稳定的应用于DC-SOFCs中。分析了DC-SOFC放电过程中电性能衰减的机制。     

薄膜型中温固体氧化物燃料电池 (SOFC)研制及性能考察

用一种廉价的湿化学方法 ,在Ni_YSZ阳极基膜上制备出致密的YttriaStabilizedZirconia(YSZ)薄膜 .薄膜的厚度约为 10 μm ,致密均匀 ,无裂纹等缺陷 .以Ni_YSZ阳极基膜 ,YSZ薄膜和锶掺杂锰酸镧阴极 (LSM )组装的SOFC单电池 ,在 80 0℃下功率密度达 0 1W /cm2 .研究分析表明 ,YSZ薄膜的IR降 (包括电极 /YSZ薄膜的接触电阻 )较小 ,不是影响电池性能的主要因素 ,大的阳极过电位是影响电池性能的主要因素 .     

固体氧化物燃料电池LSCM-CeO_2/Ni-ScSZ复合阳极制备及性能表征

采用双层流延法制备Ni-ScSZ阳极支撑层-ScSZ电解质复合膜.在烧结的Ni-ScSZ阳极支撑层表面丝网印刷一层LSCM-CeO2阳极催化层,得到LSCM-CeO2/Ni-ScSZ功能梯度层阳极.研究表明,LSCM/CeO2比为1:3(bymass)的功能梯度层阳极Ni-ScSZ13具有较佳的性能.单电池在850℃以H2和乙醇蒸气作燃料的最大功率密度分别为710和669mW/cm2,而LSCM/CeO2为1:0(bymass)的功能梯度层Ni-ScSZ10作阳极的单电池,最大功率密度分别为521和486m W/cm2.两种阳极单电池,分别在700℃于乙醇蒸气中作长时间运行实验,X-射线能量散射分析表明Ni-ScSZ13阳极比Ni-ScSZ10阳极具有较好的抗碳沉积性能.     

以甲醇为燃料的中温固体氧化物燃料电池性能研究

制备了阳极负载型LDC-LSGM双层电解质薄膜电池.考察了单电池在分别使用甲醇和氢气两种燃料时,不同温度下的I～V性能.以甲醇为燃料,以空气为氧化剂时,800℃下的最大输出功率密度为1.07W/cm²,而使用氢气为燃料时,最大输出功率密度为1.54W/cm².通过交流阻抗研究了造成甲醇性能降低的可能原因.结果表明,以甲醇作为燃料时,单电池性能较氢气作为燃料时低.     

YSZ传导膜H_2S固体氧化物燃料电池

研究了Y2O3稳定的ZrO2(YSZ)氧离子传导膜H2S固体氧化物燃料电池性能。掺杂NiS、电解质、Ag粉和淀粉制备了双金属复合MoS2阳极催化剂,掺杂电解质、Ag粉和淀粉制备了复合NiO阴极催化剂,用扫描电镜对YSZ和膜电极组装(MEA)进行了表征,比较了不同电极催化剂的性能和极化过程,考察了不同温度对电池性能的影响。结果表明,双金属复合MoS2/NiS阳极催化剂在H2S环境下比Pt和单金属MoS2催化剂稳定,复合NiO阴极催化剂比Pt性能好,在电极催化剂中加入Ag可显著提高电极的导电性;与Pt电极相比,复合MoS2阳极和复合NiO阴极催化剂的过电位较小,阳极的极化比阴极侧小;温度升高,电池的电流密度与功率密度增加,电化学性能变好。在750℃、800℃、850℃和900℃及101.13 kPa时,结构为H2S、(复合MoS2阳极催化剂)/YSZ氧离子传导膜/(复合NiO阴极催化剂)、空气的燃料电池最大功率密度分别为30 mW/cm2、70 mW/cm2、155 mW/cm2及295 mW/cm2、最大电流密度分别为120 mA/cm2、240 mA/cm2、560 mA/cm2和890 mA/cm2。     

Ni@MWCNTs催化阳极的制备及在直接尿素(尿液)燃料电池中的应用

在表面自吸附多壁碳纳米管(MWCNTs)的废弃面膜布上电沉积镍(Ni)制备得到成本低廉、结构疏松的柔性Ni@MWCNTs电极.利用扫描电子显微镜、X射线衍射仪及电感耦合等离子体质谱仪对电极的微观形貌、元素分布、晶体结构和催化剂含量进行表征.采用循环伏安法、计时电流法和交流阻抗法研究了Ni@MWCNTs的单电极催化性能和全电池输出性能.结果显示,尿素电氧化反应可能产生强吸附性的中间产物,当KOH的浓度为3.0 mol/L时,氧化峰电流密度达到最高值(18.7 mA·mg~(-1)·cm~(-2));以Ni@MWCNTs电极为负极的直接尿素燃料电池的开路电压高达0.87 V,峰功率密度为1.74 m W/cm~2.当以人类尿液为燃料时,增大燃料的pH值,能大幅提升直接尿液燃料电池的性能.     

乙烷PBI/H_3PO_4质子传导膜燃料电池性能

研究了以乙烷作为燃料、掺杂了H3PO4的聚苯并咪唑(PBI)材料作为质子传导膜、Pt/C作为电极催化剂构成的燃料电池电化学性能。采用溶液铸造法制备了PBI/H3PO4质子传导膜,考察了在PBI膜中H3PO4的掺杂量与时间的关系及乙烷气体在增湿和不增湿条件下PBI/H3PO4燃料电池的电化学性能;探讨了电池的反应机理及不同操作温度对电池性能的影响。结果表明,PBI膜H3PO4适宜的掺杂时间为8h,电解质中掺杂600mol%H3PO4;乙烷气体增湿后,电池性能变好;操作温度提高,电化学反应速率加快,电池的输出电流与功率密度增加。结构为C2H6,(Pt/C阳极)/PBI/H3PO4膜/(Pt/C阴极),O2的单电池,在200℃和0.1Mpa、乙烷气体的湿度从0增加到0.02kgH2O/kg乙烷时,电池的最大输出电流密度从1.5mA·cm-2增加到34mA·cm-2,最大功率密度从0.33mW·cm-2增加到5.5mW·cm-2。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.