Ti缓冲层及退火处理对Si(111)基片上生长的ZnO薄膜结构和发光特性的影响

采用反应磁控溅射法在Si（111）基片上制备了带有Ti缓冲层的高c轴取向ZnO薄膜.通过X射线衍射分析和光致荧光光谱测量,研究了Ti缓冲层厚度和退火处理对ZnO薄膜结晶质量和光致荧光特性的影响.研究结果表明,Ti缓冲层的引入可以有效改善Si基片上ZnO薄膜的发光性能,但缓冲层存在一个最佳的厚度.薄膜应力是影响ZnO薄膜紫外荧光发射性能的重要因素,较小的残余应力对ZnO薄膜的紫外荧光发射是有利的,残余应力的存在可以改变ZnO薄膜紫外荧光发射能量.随着退火温度的增加,薄膜中的张应力增大,导致带隙宽度减小以及激子复合跃迁峰逐渐向低能方向移动. 关键词： ZnO薄膜 缓冲层 退火处理 应力分析     

ZnO薄膜的自组织设计及形貌控制

采用单源化学气相沉积(SSCVD)法,在Si(100)基片上通过改变前驱反应体与基片的入射角度,获得了可控柱状取向的ZnO薄膜.研究发现,入射角度的改变可使沉积薄膜中的柱状结构的生成方向倾斜.但X射线衍射(XRD)分析表明:ZnO薄膜的c轴(002)取向与入射角无关,且不沿ZnO柱状结构的生长方向取向.由于ZnO的(002)面为其表面自由能最低且原子密度高的晶面,ZnO薄膜的生长更易于在垂直于基片表面的方向c轴取向生长.     

ZnO薄膜的制备和结构特性及应变

在SiO₂/Si衬底上面,利用射频磁控溅射方法,在不同的工艺条件下生长ZnO薄膜,然后进行热处理(600～1000℃退火).研究了氩氧比和退火温度对薄膜结晶性能的影响.薄膜的表面结构和晶体特性通过扫描电子显微镜(SEM)、X射线衍射(XRD)来进行表征.结果表明:所制备的薄膜为多晶纤锌矿结构,具有垂直于衬底的c轴(002)方向的择优取向性.热处理可使ZnO(002)衍射峰相对强度增强,半峰全宽(FWHM)变小,即退火使c轴生长的薄膜取向性增强.未经退火的ZnO薄膜存在张应力,经过热处理后应力发生改变,最后变成压应力,并且随着退火温度的升高,压应力逐渐增大.     

反应溅射氧化锌薄膜的结构特点及性质

以金属Zn(纯度为99.99%)作为靶材,采用离子束反应溅射法在玻璃衬底上溅射沉积了一系列ZnO薄膜样品。通过对薄膜样品X射线衍射(XRD)谱的分析,发现尽管溅射条件不同,但是ZnO薄膜只沿(0002)晶面取向生长。衬底温度和溅射气体的氧分压对薄膜沿c轴取向生长有影响,其中衬底温度的影响较明显。溅射过程中发现衬底温度为360℃最适合(0002)晶面的生长,在此温度下溅射获得了完全沿c轴取向生长且衍射峰最强的ZnO薄膜。室温下测量了ZnO薄膜的发射光谱,发现薄膜在紫外区(364nm附近)、蓝绿区(470nm附近)有较强的发光峰,在紫光区(398nm附近)、蓝光区(452nm附近)和红外区(722nm附近)有较弱的发光峰。ZnO薄膜在空气中退火,对薄膜的结构、发光和电学性质都有一定影响。合适的退火温度可以促进薄膜沿c轴的取向生长;退火后ZnO多晶薄膜的晶粒比未退火的略大;退火使部分发光峰的位置发生偏移并使薄膜的发光强度增强;退火使薄膜的电阻率显著增大,薄膜的电阻率随氧分压的增大而增大。     

以Au为缓冲层在Si衬底上生长ZnO薄膜

采用化学气相沉积(CVD)方法在Si(001)衬底上分别制备了有金属Au缓冲层以及无Au缓冲层的ZnO薄膜。其中Au缓冲层在物理气相沉积(PVD)设备中蒸发,厚度大约为300nm。有Au缓冲层的ZnO薄膜晶体质量比直接在Si衬底上生长有了显著提高。利用X射线衍射(XRD)研究了所生长ZnO薄膜的结晶质量,有Au缓冲层的ZnO薄膜虽然仍为多晶,但显示出明显的择优取向。用光学显微镜研究了ZnO薄膜的表面特征,金属Au缓冲层显著地提高了在Si衬底上生长的ZnO薄膜的晶粒尺寸及平整度。同时利用室温光致发光(PL)谱研究了ZnO薄膜的光学性质,并分析了有Au缓冲层的ZnO薄膜NEB发光峰强度反而弱的可能原因。     

分子束外延生长的ZnO压电薄膜及其声表面波器件特性

用RF-MBE在蓝宝石(0001)衬底上引入MgO和低温ZnO双缓冲层生长了ZnO薄膜,并制备了声表面波器件。在ZnO薄膜中,仅观测到(0002)面的XRD,且衍射峰增强,半高宽减小,表明ZnO薄膜c轴取向性更好,晶体结构更优。室温下自由激子吸收峰更尖锐和吸收边更陡峭以及仅观测到自由激子发光,且发光线宽变窄、发光强度变大,表明ZnO薄膜缺陷密度减小,薄膜质量提高。测得该ZnO压电薄膜的电阻率高达4×10⁷ Ω·cm,其声表面波的速度高达5 010 m/s。     

两步法制备空间取向高度一致的ZnO纳米棒阵列

采用两步法,即先用磁控溅射在Si(100)表面生长一层ZnO籽晶层、再利用液相法制备空间取向高度一致的ZnO纳米棒阵列.用扫描电子显微镜、X射线衍射、高分辨透射电子显微镜和选区电子衍射对样品形貌和结构特征进行了表征.结果表明,ZnO纳米棒具有垂直于衬底沿c轴择优生长和空间取向高度一致的特性和比较大的长径比,X射线衍射的(XRD)(0002)峰半高宽只有0.06°,选区电子衍射也显示了优异的单晶特性.光致发光谱表明ZnO纳米棒具有非常强的紫外本征发光和非常弱的杂质或缺陷发光特性. 关键词： ZnO纳米棒阵列 ZnO籽晶层 两步法 液相生长     

电沉积法制备ZnO纳米柱及其机制研究

采用阴极还原方法,以Zn(NO₃)₂水溶液为电解液制备ZnO纳米柱。分析了不同沉积电位和不同沉积时间的缓冲层对ZnO纳米柱的密度、形貌及取向的影响。通过分析缓冲层在不同沉积时间下的电流密度变化,研究了缓冲层对ZnO纳米柱密度影响的机理。利用扫描电子显微镜(SEM)和X射线衍射(XRD)分析了样品的表面形貌及结构。研究结果表明,缓冲层能够增加ZnO纳米柱的密度及c轴的取向性,当缓冲层的沉积时间为60 s时,可以得到密度最大、取向最好的ZnO纳米柱。     

La0.8Ca0.2MnO3/SrTiO3薄膜厚度对其结构及磁学性能的影响

采用多种X射线衍射技术和磁电阻测量技术研究了不同厚度的La_0.8Ca_0.2MnO₃/SrTiO₃ (LCMO/STO)薄膜的应变状态及其对磁电阻性能的影响.结果表明，在STO(001)单晶衬底上生长的LCMO薄膜沿［00l］取向生长.LCMO薄膜具有伪立方钙钛矿结构，随着薄膜厚度的增加，面内晶格参数增加，垂直于面内的晶格参数减小,晶格参数a和b相近，略小于c.LC 关键词： X射线衍射 微结构 应变 物理性能     

氧化处理的蓝宝石基片上沉积的ZnO/MgO多量子阱的结构及光学性质研究

采用射频反应磁控溅射的方法,在经过氧化处理的Al₂O₃（0001）基片上制备了具有良好调制结构的ZnO/MgO多层膜量子阱.利用X射线反射率测量、X射线衍射分析、电子探针显微分析、原子力显微镜、透射光谱以及光致发光光谱等表征技术,研究了ZnO/MgO多量子阱的结构、表面形貌和光致发光等特性.XRD以及扫描的结果表明多层膜样品具有高c轴择优取向并且与蓝宝石基片有良好的外延关系.通过X射线反射率测量的结果得到多量子阱的调制周期,结合电子 关键词： ZnO/MgO 多量子阱 反应磁控溅射 变温光谱     

Morphology and photoluminescence study of electrodeposited ZnO films

ZnO films on ITO substrates and Au coated ITO substrates were fabricated by using electrodeposition technique. We carried out the experiments by adjusting the concentration of solution, potential, substrate, and temperature. The effect of temperature on the growth of the film has been examined. SEM images have shown that there are several kinds of grown competitions for the deposition of ZnO films, but three kinds of them are dominant. One is the discrete hexagonal column structure, the other is the pentagonal structure, and the third one is of well-oriented hexagonal columns with well-aligned structure. The explanation on the grown competition is discussed. ZnO hexagonal column structures with well-aligned and well-perpendicular to the surface were successfully obtained on Au/ITO substrate in aqueous solvent of electrolyte. Clearly the main columns in the film were obtained by increasing the temperature. Its photoluminescence (PL) study at low temperature exhibited the optical properties as wurtzite ZnO and indicated the existence of macrocrystalline ZnO. A better quality of ZnO columnar structures after annealing was demonstrated from PL analysis and discussion on the existence of 370 nm, 384 nm and 639 nm in the emission bands before and after annealing.     

Study of the MOCVD growth of ZnO on GaAs substrates: Influence of the molar ratio of the precursors on structural and morphological properties

ZnO thin films were grown by metal-organic chemical vapour deposition (MOCVD) on GaAs(100) and GaAs(111)A substrates. The growth experiments were performed at temperatures ranging from 290 to 500 C and atmospheric pressure. Diethylzinc (DEZn) and tertiary butanol (tBuOH) were used as Zn and O precursors, respectively. The crystallinity of the grown films was studied by X-Ray Diffraction (XRD) and the thickness and morphology were investigated by Scanning Electron Microscopy (SEM). The influence of substrate orientation and molar ratio of the precursors on the crystalline orientation and morphology of the ZnO grown films was analysed.     

Comparative studies on structural and optical properties of ZnO films grown on c-plane sapphire and GaAs (001) by MOCVD

ZnO thin films were grown on c-plane sapphire and GaAs (001) substrates by metalorganic chemical vapor deposition. Atomic force microscopy and double-crystal X-ray diffractometry were utilized to investigate the structural properties of the ZnO films. The optical properties of ZnO films were also investigated in terms of time integrated and resolved photoluminescence (TIPL and TRPL). Large hexagonal crystallites and better crystalline quality were observed from the ZnO film on sapphire. Also, both the TIPL and TRPL showed a significant difference as the substrate changed. In particular, a detected sharp contrast in the result of TRPL measurement is due to the different defect structure and the lattice strain and stress of ZnO films on different substrates.     

p型ZnO薄膜的制备及特性

采用射频磁控溅射在Si片上制备ZnO薄膜，通过离子注入对样品进行N掺杂，在不同温度下进行退火并实现了p型转变.用扫描电子显微镜、X射线衍射和Hall测量对薄膜进行了表征，结果表明薄膜具有良好的表面形貌和高度c轴择优取向，退火后p型ZnO薄膜的最高载流子浓度和最低电阻率分别为1.68×10¹⁶cm^-3和41.5Ω·cm.讨论并分析了退火温度和时间对ZnO薄膜p型转变的影响.     

热处理对ZnO/Au薄膜结构和压电特性的影响

通过射频磁控溅射在氧化硅片表面沉积ZnO/Au薄膜,并通过不同的热处理方式对薄膜进行退火。为了研究退火对ZnO/Au薄膜结构和压电特性的影响,采用X射线衍射分析（XRD）、光学显微镜、场发射扫面电镜（FESEM）和压电力分析仪对薄膜退火前后的材料特性进行了分析。研究发现,热处理能够改善ZnO/Au薄膜的结晶质量。特别是在氮气保护氛围下慢速退火后,薄膜结晶质量有明显改善。但是,热处理导致了薄膜的压电系数d33和d31降低。分析认为,热处理过程中Au原子在ZnO中的易迁移特性破坏了ZnO/Au薄膜的压电性能。     

Pulsed laser deposition of ZnO grown on glass substrates for realizing high-performance thin-film transistors

We report characterization of ZnO thin-film transistors (TFTs) on glass substrates fabricated by pulsed laser deposition (PLD). ZnO films were characterized by X-ray diffraction (XRD), atomic force microscopy and Hall effect measurements. The XRD results showed high c-axis-oriented ZnO(0002) diffraction corresponding to the wurtzite phase. Moreover, the crystallization and the electrical properties of ZnO thin films grown at room temperature are controllable by PLD growth conditions such as oxygen gas pressure. The ZnO films are very smooth, with a root-mean-square roughness of 1 nm. From the Hall effect measurements, we have succeeded in fabricating ZnO films on glass substrates with an electron mobility of 21.7 cm²/V s. By using the ZnO thin film grown by two-step PLD and a HfO₂ high-k gate insulator, a transconductance of 24.1 mS/mm, a drain current on/off ratio of 4.4×10⁶ and a subthreshold gate swing of 0.26 V/decade were obtained for the ZnO TFT.     

The influence of Au thickness on the structural,optical and electrical properties of ZnO/Au/ZnO multilayer films

Transparent and conductive ZnO/Au/ZnO (ZAZ) multilayer films were deposited on glass substrates by magnetron sputtering without intentional substrate heating. The thickness of Au interlayer was set at 1, 2 and 3 nm.The observed structural, optical and electrical properties were dependent on the thickness of the Au interlayer. For all of the ZAZ films, the diffraction peaks in the XRD pattern were identified as the (002) and (103) planes of a ZnO films and the (111) plane of an Au interlayer. The ZAZ films with a 2 nm thick Au interlayer showed a higher figure of merit than the other ZAZ films prepared in this study, and they also demonstrated the relatively high work function of 5.13 eV.From these results, we concluded that a ZAZ film with a 2 nm thick Au interlayer is an alternative candidate for use as a transparent electrode in OLEDs and various flat panel displays.     

The structure and optical characters of the ZnO film grown on GaAs/Al2O3 substrate

In this paper ZnO films are grown on GaAs/Al₂O₃ substrates at different temperature by metal-organic chemical vapor deposition (MOCVD). The GaAs/Al₂O₃ substrates are formed by depositing GaAs layer (∼35 nm) on the Al₂O₃ substrate. The results of X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) demonstrate that most of the Ga and As atoms form Ga-As bond and the GaAs layer does not present any orientation. The characters of the ZnO films grown on GaAs/Al₂O₃ substrates are investigated by XRD, photoluminescence (PL), atomic force microscopy (AFM) and Raman scattering. Compared with ZnO film grown on Al₂O₃ substrate, ZnO film prepared by our fabrication scheme has good crystal and optical quality. Meanwhile its grain size becomes bigger according to the AFM image. Raman analysis indicates that the intrinsic defects and the in-plane tensile stress are obviously reduced in ZnO/GaAs/Al₂O₃ samples.     

Au层退火温度对ZnO/Au/ZnO多层膜的结构、光学及电学性质的影响

采用金属有机化学气相沉积(MOCVD)技术在蓝宝石衬底上制备出晶体质量较好的透明导电的ZnO/Au/ZnO(ZAZ)多层膜,其中,Au夹层是通过射频磁控溅射的方法获得。通过对Au夹层进行不同温度的退火处理,研究了Au层退火温度对ZAZ多层膜的结构特性、电学性能和光学特性的影响。利用原子力显微镜(AFM)、扫描电子显微镜(SEM)、X射线衍射(XRD)仪、霍尔效应测试和透射谱分析等测试手段对ZAZ多层膜的性质进行了分析。测试结果表明,在200 ℃下对Au夹层进行快速退火处理,多层膜的结构、电学和光学性质达到最优,表面等离子体效应也更明显。其中,XRD(002)衍射峰的半高宽为0.14°,电阻率为2.7×10^-3 Ω·cm,载流子浓度为1.07×10²⁰ cm^-3,可见光区平均透过率为75.3%。     

气相输运法制备ZnO薄膜(英文)

运用气相输运技术在不同的衬底上制备ZnO薄膜,同时对这些ZnO薄膜的表面形貌、晶体结构和光学特性进行表征。在扫描电子显微镜图像上可以看到,相比没有镀金的Si衬底,ZnO纳米颗粒在镀金的Si衬底上的生长尺寸较大。X射线衍射测试结果表明,在Si(111)和Si(100)衬底上生长的ZnO薄膜显示出不同的六角纤锌矿结构的衍射峰,但没有出现立方闪锌矿ZnO结构的衍射峰。在镀金的Si衬底上,ZnO薄膜生长取向主要为c轴方向。此外,所有ZnO样品的光致发光谱上均只出现一个狭窄且强的紫外峰,约在389 nm(3.19 eV)波长处。