Pre-irradiation of surfactants to enhance their capacity to solubilise drugs and dyes

The present work has used pre-irradiation of surfactants in order to enhance their capacity to solubilize hydrophobic drugs and dyes. Aqueous solution of two pluronic surfactants viz., F-127 and P-123 were subjected to gamma radiation. These irradiated surfactant solutions were used to solubilize five drugs such as ornidazole, tinidazole, ciprofloxacin, aceclofenac, and methylparaben, and two dyes, methyl orange and eosin yellow. Their capacity for enhancing solubilisation was compared with that of unirradiated surfactants. The irradiated surfactant solutions displayed 0.88%–31.9% higher solubilisation compared to unirradiated surfactant solutions. This phenomenon of enhancement in solubility is explained through changes in the physical properties like decreased surface tension and increased hydrodynamic radius in irradiated block polymeric surfactants. Irradiation of surfactants for enhancing their capacity to solubilize hydrophobic chemical entities has been used for the first time.     

The partition of ethoxylated non-ionic surfactants between two non-miscible phases

The partition of a polydispersed ethoxylated non-ionic surfactant in equilibrated oil–water systems has been studied at 25 °C. The model surfactant used was a commercial sample of nonylphenol ethoxylated with 10 moles of ethylene oxide (NPEO₁₀). The partition isotherms over the range of surfactant concentration including the critical micelle concentration (CMC) were made with n-hexane, i-octane and n-decane as oil phases. Each partition isotherm exhibits a change of slope that matched the CMC value of surfactant determined by surface tension measurements on aqueous solutions. During the partition of NPEO₁₀ in the oil–water systems, the oligomer distribution in the oil and water phases changed because of fractionation. Below CMC, the mean ethoxylation degree in the oil phase was smaller, whereas in water it was higher than the mean initial value of the surfactant. Moreover, the mean ethoxylation degree in both oil and water phase was practically independent of surfactant concentration. Above CMC, the mean distribution of ethoxymers decreased in both phases. This was ascribed to the competition between micelles from water and the oil phase for the more hydrophobic species of the surfactant. The mean distribution of ethoxymers in the aqueous phase asymptoted to a value that was the mean of the surfactant itself, whereas it steeply decreased in the organic phase.     

Transfer of coenzyme Q0 from water to aqueous surfactant solutions: the case of Triton X-100

The effect of UQ0 on the micellization equilibrium of Triton X-100 has been studied by the analysis of the UV absorption spectra of Triton X-100. In the range of the UQ0 concentration investigated, the critical micelle concentration (CMC) increases at increasing of the solute concentration. The dependence of the CMC on UQ0 concentration has been used to calculate the generalized Setchenov constant. Mixing and dilution enthalpies of aqueous solutions of UQ0 and Triton X-100 were measured and used to calculate the enthalpies of transfer of UQ0 from water to Triton X-100 aqueous solutions. From the dependence of the enthalpy of transfer on surfactant concentration, the distribution constant between aqueous and micellar phase and the standard enthalpy of transfer from water to Triton X-100 micelles were evaluated along with the standard transfer free energy and entropy. All measurements were carried out at 298 K.     

Effect of ethanol on the aggregation properties of cetyltrimethylammonium bromide surfactant

Surfactant aggregation properties in aqueous and mixed organic/aqueous solutions have attracted considerable interests especially for the applications to the template synthesis of nanoporous inorganic materials. In this work, we study the aggregation behavior of cetyl trimethylammonium bromide surfactant in both aqueous and mixed water/ethanol solutions by the steady-state fluorescence probe technique. The critical micelle concentration (CMC) and the micelle aggregation number were determined in solutions with different ethanol contents. The CMC increases and the aggregation number decreases with increasing ethanol content in solutions. The effect of ethanol on the micelle formation can be treated as a structure breaking process. The density functional theory was used to calculate the charge density distribution over the surfactant molecules in different solvents. The results obtained reveal that the micelle size distribution in solutions can be adjusted by varying the content of ethanol in solvents.__________From Kolloidnyi Zhurnal, Vol. 67, No. 2, 2005, pp. 186–191.Original English Text Copyright © 2005 by Li, Han, Zhang, Wang.This article was submitted by the authors in English.     

Study of the aggregation of nonylammonium chloride in aqueous solutions of sodium chloride by vapor pressure osmometry

We determined osmotic coefficients from vapor pressure osmometry (VPO) measurements on aqueous solutions of nonylammonium chloride in the presence of NaCl at 30°C. VPO data were subsequently used to determine the critical micelle concentration (CMC) of the solutions of this surfactant. The values of this parameter obtained from VPO are well correlated with those obtained from light scattering. No premicellar aggregation was observed at surfactant concentrations below the CMC. The osmotic coefficients below the CMC may be evaluated from the extended form of the Debye–Hückel equation. Above the CMC, the dependence of the osmotic coefficient on the surfactant concentration was indicative of the occurrence of aggregation rather than the interactions in the system. Some comments are made on the uncertainty in the value of some parameters in micellar solutions and possible source of error using the VPO technique in these solutions.     

Extension of the Taylor Equation for Oil-Water-Surfactant System and Investigating the Impact of Surfactant Concentration over the Quality of Emulsion

Emulsions stand among the most important multiphase fluids, exhibiting various complicated phenomenon. To understand the process of emulsification, the Taylor equation has been extended to incorporate the parameters that depend on molecular mass of oil and their contents and the amount of surfactant added. To test the validity of the proposed equations, four well-defined short chain (n-hexane, n-heptane, n-decane, and kerosene) oils were emulsified in water and the results were compared with the experimental ones. It has been concluded that the extended Taylor equation worked well, even in the presence of surfactant. The quality of the emulsion defined and discussed in terms of size and number of droplets was best near CMC of the surfactant used. A relationship has also been derived between CMC of surfactant and its distribution coefficient, which allows the exact value of one parameter to be determined if other is known.     

Thinning of foam films of micellar surfactant solutions

Drainage in microscopic circular foam films depends significantly on the radial (tangential) mobility of the film surfaces and is accelerated as compared to the limiting case of tangentially immobile surfaces, where velocity of thinning is described by the classical Reynolds’ equation (outflow of viscous fluid from a cylindrical gap between two solid plates). The structure and composition of the adsorption layer and the interfacial mass transfer determine the tangential mobility of the film surfaces and, hence, the measured velocity of film thinning. Experiments with soluble surfactants below the critical micelle concentrations (CMC) have exhibited the effect of dynamic interfacial elasticity. At relatively low bulk concentrations, the interfacial mass transfer is governed by surface diffusion; close to CMC (saturated adsorption layer), the limiting case of tangentially immobile surfaces can be reached and at concentrations above the CMC the film thinning is accelerated again. Here, we report freshly established data on the kinetic behavior of foam films from micellar solutions of soluble nonionic surfactants (decyl-octaoxyethylene alcohol and dodecyl-octaoxyethylene alcohol) in a wide range of concentrations above the CMC aiming to investigate the effect of partially disintegrated micelles acting as sources of surfactant molecules at the surface.     

Influence of the Hofmeister anions on self-organization of 1-decyl-3-methylimidazolium chloride in aqueous solutions

Inorganic salts usually influence water structure affecting the hydration of the molecules which lead to a salting-in or a salting-out effect of hydrophobic compounds. Specific conductivity and isothermal titration calorimetry have been used to study the effect of inorganic salts on aggregation of the cationic surfactant 1-decyl-3-methylimidazolium chloride in aqueous solutions. The effect of the concentration, the nature of the anion and temperature on micelle formation were studied. A decreasing critical micelle concentration (CMC) due to the weakening electrostatic repulsion between the headgroups was observed. The salts used in this investigation decreased the CMC and degree of micelle ionization in the order of Cl(-)相似文献   

Capillary electrophoretic studies on the migration behavior of cationic solutes and the influence of interactions of cationic solutes with sodium dodecyl sulfate on the formation of micelles and critical micelle concentration

The migration behavior of cationic solutes and influences of the interactions of cationic solutes with sodium dodecyl sulfate (SDS) on the formation of micelles and its critical micelle concentration (CMC) were investigated by capillary electrophoresis at neutral pH. Catecholamines and structurally related compounds, including epinephrine, norepinephrine, dopamine, norephedrine, and tyramine, which involve different extents of hydrophobic, ionic and hydrogen-bonding interactions with SDS surfactant, are selected as cationic solutes. The dependence of the effective electrophoretic mobility of cationic solutes on the concentration of surfactant monomers in the premicellar region provides direct evidence of the formation of ion-pairs between cationic solutes and anionic dodecyl sulfate monomers. Three different approaches, based on the variations of either the effective electrophoretic mobility or the retention factor as a function of surfactant concentration in the premicellar and micellar regions, and the linear relationship between the retention factor and the product of a distribution coefficient and the phase ratio, were considered to determine the CMC value of SDS micelles. The suitability of the methods used for the determination of the CMC of SDS with these cationic solutes was discussed. Depending on the structures of cationic solutes and electrophoretic conditions, the CMC value of SDS determined varies in a wide concentration range. The results indicate that, in addition to hydrophobic interaction, both ionic and hydrogen-bonding interactions have pronounced effects on the formation of SDS micelles. Ionic interaction between cationic solutes and SDS surfactant stabilizes the SDS micelles, whereas hydrogen-bonding interactions weakens the solubilization of the attractive ionic interaction. The elevation of the CMC of SDS depends heavily on hydrogen-bonding interactions between cationic solutes and SDS surfactant. Thus, the CMC value of SDS is remarkably elevated with catecholamines, such as epinephrine and norepinephrine, as compared with norephedrine. In addition, the effect of methanol content in the sample solution of these cationic solutes on the CMC of SDS was also examined.     

Effect of Surfactants on the Behavior of Chromium in Analytical Flame Atomic Absorption Spectrometry

The behavior of surfactants of different natures and chain lengths was studied in flame atomic absorption spectrometry (FAAS) analyses. The variations of absorbance, which arise as a consequence of the surfactant addition to aqueous solutions of Cr(VI) or Cr(III), were measured. Depressions were observed below the critical micelle concentration (CMC), whereas enhancements were observed above the CMC. These depressions are more significant when the surfactant is opposite in charge to the analyte and the longest surfactant chain is used. A mechanism that enables explanation of the effects of a surfactant on FAAS is also suggested. This mechanism is based on the preferential orientation of surfactant molecules to the surface of nebulized droplets.     

Effect of gamma-radiation on the Sn(II) content,radiochemical purity,in-vitro stability and biological distribution of some99mTc-labelled freeze dried kits

Gamma-irradiation can be used for the sterilization of some^99mTc-labelled freeze dried kits. In connection with this the effect of -radiation on Sn(II) content, radiochemical purity,in-vitro stability and biological distribution of some currently used^99mTc-labelled kits has been investigated. For irradiation the certain radiation sterilization doses (25 and 50 kGy) were used. A variable decrease of Sn(II) content was observed in all -irradiated kits. The losses are in the order of 10–25% compared with the Sn(II) content of original ones. The colour of the irradiated kits did not changed except DTPA which developed yellow colour after irradiation. For the irradiated and original kits nearly the same pH were found. The irradiated kits seemed to undergo partial decomposition or chemical alteration which led to some deviation of the biological distribution of them.     

Synergism and Physicochemical Properties of Anionic/Amphoteric Surfactant Mixtures with Nonionic Surfactant of Amine Oxide Type

The physicochemical properties of initial formulation, that is anionic/amphoteric surfactants mixture SLES/AOS/CAB (sodium lauryl ether sulfate (SLES), α-olefin sulfonates (AOS) and cocamidopropyl betaine (CAB) at ratio 80 : 15 : 5) with nonionic surfactant of amine oxide type (lauramine oxide (AO)) in various concentration (1–5%) were studied. To characterize the surfactants mixture, the critical micelle concentration (CMC), surface tension (γ), foam volume, biodegradability and irritability were determined. This study showed that adding of AO in those mixtures lowered both γ and CMC as well as enhanced SLES/AOS/CAB foaming properties, but did not significantly affect biodegradability and irritability of initial formulation. Moreover, an increase in AO concentration has a meaningful synergistic effect on the initial formulation properties. All those results indicates that a nonionic surfactant of amine oxide type significantly improves the performance of anionic/amphoteric mixed micelle systems, and because of that anionic/amphoteric/nonionic mixture can be used in considerably lower concentrations as a cleaning formulation.

     

Radiation effect studies on anticancer drugs, cyclophosphamide and doxorubicin for radiation sterilization

Two anticancer drugs, cyclophosphamide (CPH) and doxorubicin hydrochloride (DOXO), in powder form were exposed to a range of doses of ⁶⁰Co gamma and electron beam radiation to study the effects of ionizing radiation. Pharmacopoeia tests, discolouration, degradation products, effect of irradiation temperature and dose rate were investigated. CPH undergoes less than 2% degradation at 30 kGy. Chromatographic studies revealed formation of several trace level degradation products, discolouration and free radicals in the irradiated CPH. N,N-bis (2-chloroethyl) group in the molecule is particularly sensitive to radiation degradation. Irradiation to 5 kGy at low temperature (77 K) did not result in significant changes. DOXO was observed to be quite radiation resistant and did not undergo significant changes in its physico-chemical properties and degradation product profile. It can be radiation sterilized at normal sterilization dose of 25 kGy.     

Application of a chemical equilibrium model to thermodynamic functions of transfer of alcohols from water to aqueous surfactants

In ternary aqueous solutions, hydrophobic solutes such as alcohols tend to aggregate with surfactants to form mixed micelles. These systems can be studied by meas of the functions of transfer of hydrophobic solutes from water to aqueous solutions of surfactant. These thermodynamic functions often go through extrema in the critical micellar concentration (CMC) region of the surfactant. A simple model based on interactions between surfactant and hydrophobic solute monomers, on the distribution of the hydrophobic solute between water and the micelles and on the shift in the CMC induced by the hydrophobic solute, can simulate the magnitude and trends of the transfer functions using parameters which are mostly derived from the binary systems. In order to check the model more quantitatively, volumes and heat capacities of transfer of alcohols from water to aqueous solutions of a nonionic surfactant, octyldimethylamine oxide, were measured. A quantitative agreement was achieved with three adjustable parameters. Good fits are also obtained for the transfers to the ionic surfactants, octylamine hydrobromide and sodium dodecylsulfate. When the equilibrium displacement contribution is small, the distribution constants and the partial molar properties of the alcohols in the micellar phase agree well with the parameters obtained with similar models.     

Phase conditions,hydrodynamic features and salt influence in the polymer-amphiphile interaction for the EHEC/SDS/water system

Two fractions of ethyl(hydroxy)ethyl cellulose, EHEC, and their interactions with sodium dodecyl sulphate, SDS, have been investigated. The effect of salt on these interactions was explored. The more hydrophobic fraction exhibits a cloud point (CP) of 30°C, and the more hydrophilic fraction has a CP around 65°C. The properties of the systems were studied by means of hydrodynamic (viscosity), equilibrium dialysis and cloud point measurements. Dye solubilization was used to obtain indications of cluster formation on the polymer backbone. The equilibrium dialysis shows a steep binding beginning at a critical surfactant concentration indicating a cooperative effect in the EHEC/SDS/water system. It is found that when the degree of binding is moderate and only 10–20% of the value at saturation, the specific viscosity effects occur and solutions containing high polymer concentrations pass a marked maximum in viscosity. It is shown that the maximum in viscosity and the collcoil interaction, expressed as Huggins constant,k _H, appear a composition with the same fractional amount of SDS adsorbed to both EHEC fractions. It was found that the onset of redistribution and increase in viscosity were shifted to higher SDS concentrations, although still below the normal CMC, for the EHEC fraction with a high CP. When small amounts of salt are present in the EHEC/SDS/water solutions, the CP curves develop a pronounced minimum at low SDS concentrations. The redistribution of SDS to the polymers starts immediately in the presence of salt, but the viscosity of the solutions is affected only in a very narrow composition interval.     

Adsorption and Micellization in Solutions of Dodecylpyridinium Bromide–Nonionic Surfactant Mixtures

Dependences of the surface tension of aqueous solutions of cationic (dodecylpyridinium bromide) and nonionic (Tween 80, Triton X-100) surfactants and their mixtures on total surfactant concentration and solution composition were studied. The values of critical micellization concentration (CMC) and excess free energy of adsorption were determined from tensiometric measurements. Based on Rubingh–Rosen model (approximation of the theory of regular solutions), the compositions of micelles and adsorption layers at the solution–air interface as well as parameters of interaction between the molecules of cationic and nonionic surfactants were calculated for the systems indicated above. It was established that, in the case of surfactant mixtures with considerable difference in the CMCs, the micelles of individual surfactant with lower CMC value are formed. The effect of negative deviation from the ideality during the adsorption of surfactants from mixed solutions at the solution–air interface was disclosed. It was shown that the interaction energy depends significantly on the composition of mixed systems.     

Amphiphilic nanostructures in foam films

The revised articles outline the potential of microscopic foam film instrumentation as an investigation tool in studying the amphiphilic nanostructures in aqueous surfactant solutions. The impact of amphiphilic nanostructures on the drainage behaviour and stability of foam films is traced for surfactant solutions of concentrations orders of magnitude above CMC (micellar solutions) to about two orders of magnitude lower than CMC (premicellar solutions). It is found that in the high-concentration domain the micellar entities affect mainly the stability of the films. In the low-concentration domain, the presence of smaller crumbly aggregates (premicelles), plays a significant role for the kinetic stability of the films. Through the mechanism of Marangoni effect, an enhanced coupling of the specific film hydrodynamics and the mass transfer of the surfactant is obtained. The result is a sharp rise in the kinetic stability of the foam films. The importance of this trend of research is related to providing better insight into the self-assembling phenomena and into the factors that determine the drainage and the stability of thin liquid films. The results have potential and actual applications in food, cosmetic and pharmaceutical industries, as well as in biology and medicine.     

The influence of radio-frequency radiation on thermal stability of bovine serum albumin in aqueous solution

Protein unfolding events were studied by differential scanning calorimetry (DSC) for bovine serum albumin (BSA) aqueous solutions exposed to radio-frequency radiation. No immediate effect of this radiation on thermal unfolding of BSA was observed. The differences between irradiated and control samples have appeared during the storage of BSA solution. The irradiated samples changed faster than non-irradiated. Our results indicated that the age-related changes were stronger for 3.5 and 5 MHz than for 247 MHz frequency and dependent on energy power of radiation. Deconvolution of DSC traces allowed to study the effect of radio-frequency radiation on each component transition. This revised version was published online in July 2006 with corrections to the Cover Date.     

Wettability of ionic surfactants SDS and DTAB on wheat (Triticum aestivum) leaf surfaces

Abstract

Due to the important use of pesticide formulation, it is necessary to make it clear how ionic surfactant effect the wettability at leaf surface. In this work, we used the sessile drop method to study the wettability of SDS and DTAB on wheat leaf surfaces at different leaf stages, and reveal the relationship between surfactants structures and leaf stages of wheat leaf surfaces on wettability behavior. Results showed that few surfactant molecules adsorbed at the interface at low concentrations. With the concentration increased, the surfactant replaced the air layer partially within the nano/micro structure of leaf surfaces. When the concentration exceeded to CMC, the adsorption of surfactant molecules was saturated at both air-liquid interface and solid-liquid interface, the wetting state was still the transitional state between Cassie-Baxter’s and Wenzel’s state. In all concentrations, the adhesional tension and surface tension showed the linear relationship and the slope values were all below ?1, suggesting there were more surfactant molecules adsorbed at the solid-liquid interface than the liquid-air interface. As SDS is a common wetting agent and DTAB is a common fungicide in agrochemical, this study will provide potential guidance in practical application of pesticide solutions in leaf surface wetting.     

Investigation on Gas Storage in Methane Hydrate

The effect of additives (anionic surfactant sodium dodecyl sulfate (SDS), nonionic surfactantalkyl polysaccharide glycoside (APG), and liquid hydrocarbon cyclopentane (CP)) on hydrate inductiontime and formation rate, and storage capacity was studied in this work. Micelle surfactant solutions werefound to reduce hydrate induction time, increase methane hydrate formation rate and improve methanestorage capacity in hydrates. In the presence of surfactant, hydrate could form quickly in a quiescentsystem and the energy costs of hydrate formation were reduced. The critical micelle concentrations of SDS and APG water solutions were found to be 300x 10-6 and 500x 10-6 for methane hydrate formation systemrespectively. The effect of anionic surfactant (SDS) on methane storage in hydrates is more pronounced compared to a nonionic surfactant (APG). CP also reduced hydrate induction time and improved hydrateformation rate, but could not improve methane storage in hydrates.