Premixed turbulent flame front structure investigation by Rayleigh scattering in the thin reaction zone regime

Premixed turbulent flames of methane–air and propane–air stabilized on a bunsen type burner were studied using planar Rayleigh scattering and particle image velocimetry. The fuel–air equivalence ratio range was from lean 0.6 to stoichiometric for methane flames, and from 0.7 to stoichiometric for propane flames. The non-dimensional turbulence rms velocity, u′/S_L, covered a range from 3 to 24, corresponding to conditions of corrugated flamelets and thin reaction zones regimes. Flame front thickness increased slightly with increasing non-dimensional turbulence rms velocity in both methane and propane flames, although the flame thickening was more prominent in propane flames. The probability density function of curvature showed a Gaussian-like distribution at all turbulence intensities in both methane and propane flames, at all sections of the flame.The value of the term Dκ, the product of molecular diffusivity evaluated at reaction zone conditions and the flame front curvature, has been shown to be smaller than the magnitude of the laminar burning velocity. This finding questions the validity of extending the level set formulation, developed for corrugated flames region, into the thin reaction zone regime by increasing the local flame propagation by adding the term Dκ to laminar burning velocity.     

Reaction zone structures and mixing characteristics of partially premixed swirling CH4/air flames in a gas turbine model combustor

The mixing, reaction progress, and flame front structures of partially premixed flames have been investigated in a gas turbine model combustor using different laser techniques comprising laser Doppler velocimetry for the characterization of the flow field, Raman scattering for simultaneous multi-species and temperature measurements, and planar laser-induced fluorescence of CH for the visualization of the reaction zones. Swirling CH₄/air flames with Re numbers between 7500 and 60,000 have been studied to identify the influence of the turbulent flow field on the thermochemical state of the flames and the structures of the CH layers. Turbulence intensities and length scales, as well as the classification of these flames in regime diagrams of turbulent combustion, are addressed. The results indicate that the flames exhibit more characteristics of a diffusion flame (with connected flame zones) than of a uniformly premixed flame.     

A flamelet analysis of the burning velocity of premixed turbulent expanding flames

Direct numerical simulation is a very powerful tool to evaluate the validity of new models and theories for turbulent combustion. In this paper, direct numerical simulations of spherically expanding premixed turbulent flames in the corrugated flamelet regime are performed. The flamelet-generated manifold method is used to deal with detailed reaction kinetics. The numerical method is validated for both laminar and turbulent expanding flames. The computational results are analyzed by using an extended flame stretch theory. It is investigated whether this theory is able to describe the influence of flame stretch and curvature on the local burning velocity of the flame. If the full profiles of flame stretch and curvature through the flame front are included in the theory, the local mass burning rate is predicted accurately. The influence of several approximations, which are used in other existing theories, is studied. When flame stretch is assumed to be constant through the flame front or when curvature of the flame front is neglected, the theory fails to predict the local mass burning rate.     

Detailed measurements of local scalar front structures in stagnation-type turbulent premixed flames

Local scalar front structures of OH mole fraction, reaction progress variable, and its three-dimensional gradient have been measured in stagnation-type turbulent premixed flames. The reaction progress variable front is observed to change with increasing turbulence from parallel iso-scalar contours but reduced progress variable gradients, called the lamella-like front, to disrupted non-parallel iso-contours that deviate substantially from those of wrinkled laminar flamelets, called the non-flamelet front. This transition is attributed to the different scales of interaction between the flame internal structure and a spectrum of turbulence extending from the integral scale to the Kolmogorov scale. The lamella-like front pattern occurs when the length scales of interaction are smaller than the laminar flame thickness but the time scales are greater than the flame residence time. The non-flamelet front pattern occurs when the length scales of interaction are greater than the laminar flame thickness but the time scales are smaller than the flame residence time. This difference corresponds to the change of combustion regime from complex-strain flame front to turbulent flame front on a revised regime diagram. A correlation is also proposed for the turbulent flame brush thickness as a function of turbulent Reynolds number and heat release parameter. The heat release parameter is considered to arise from the non-passive effects of flame-surface wrinkling.     

Evaluation of models for flame stretch due to curvature in the thin reaction zones regime

Direct numerical simulation (DNS) was used to study modelling assumptions for the curvature-propagation component of flame stretch in the thin reaction zones regime of turbulent premixed combustion, a regime in which small eddies can penetrate the preheat zone but not the thinner fuel breakdown zone. Simulations of lean hydrogen–air and methane–air flames were conducted, and statistics of flame stretch due to curvature, henceforth referred to simply as stretch, were extracted from a species mass fraction iso-surface taken to represent the flame. The study focussed on investigating the modelling assumptions of Peters [J. Fluid Mech. 384 (1999) 107]. It was found that the mean stretch is dominated by stretch due to correlations of flame speed with curvature, and specifically the effects of tangential diffusion. The modelling suggestions of Peters were found to provide an improvement over the assumptions of a constant flame speed or a flame speed governed by the linear relationship with stretch at small and steady stretch. However for the conditions considered here, diffusive-thermal effects remain well into the thin reaction zones regime, and the suggestions of Peters generally over-predict the mean compressive stretch. An effective diffusivity for flame stretch was suggested and evaluated for the methane simulations. It was found that the effective diffusivity was comparable to the mass diffusivity for flames with a high ratio of flame time to eddy turnover time. The length scales contributing to stretch were investigated, and it was found that while most flame area has a radius of curvature greater than the laminar flame thickness, most stretch occurs in more tightly curved flame elements.     

Heat recirculation effects on flame propagation and flame structure in a mesoscale tube

Heat recirculation effects on flame propagation and flame structure are theoretically and experimentally examined in a mesoscale tube as the simplest model of heat-recirculating burners. Solutions for steady propagation are obtained using a one-dimensional two-temperature approximation. The results show that the low heat diffusivities of common solid materials permit significant heat recirculation through the wall only for a slowly-propagating condition, otherwise the flame behaves almost like a freely-propagating nonadiabatic flame. This limited heat recirculation sharply pinches and stretches two well-known branches of the freely-propagating nonadiabatic flame, resulting in the appearance of two slow-propagation branches. On the upper slow-propagation branch flames can reach superadiabatic temperatures and on the lower one, which is stretched from the classical unstable lower branch, flames can be stable. As the tube inner diameter decreases, another burning regime appears where flames are barely sustained by the heat recirculation. Further reduction of the tube inner diameter makes no flame exist. It is also revealed that a flame in a mesoscale tube has two length scales, i.e. the conventional flame thickness and a convective preheat zone thickness, and that the latter should be much larger than the former for significant heat recirculation. It is theoretically predicted that a heat-recirculating, even superadiabatic, flame with positive propagation velocity against the gas flow can exist in a mesoscale tube. It is also found that a flame transition from one branch to another in a given tube is well described by only one dimensionless parameter. Finally, these theoretical results show good qualitative agreements with experiments, especially for the transition behaviours.     

Subgrid combustion modeling of 3-D premixed flames in the thin-reaction-zone regime

Large eddy simulation (LES) is used to investigate three-dimensional (3D) lean premixed turbulent methane–air flames in the thin-reaction-zone regime. In this regime, the Kolmogorov scale is smaller than the preheat zone thickness, but larger than the reaction zone thickness. Past numerical studies of similar flames were primarily direct numerical simulation either in two-dimensions or using the artificially thickened flame approach in 3D. For an LES the effect of small (unresolved) scales on the scalar field must be, modeled accurately to capture the correct flame structure. A subgrid combustion model based on the linear-eddy-mixing (LEM) model is used within an LES framework (called LEM–LES hereafter) to capture the 3D flame-structure of the highly stretched premixed flames. A finite-rate, one-step methane–air chemistry with a non-unity Lewis number formulation is used in this study. The simulated flame structure resembles flames experimentally studied in the thin-reaction-zone regime. Even though the preheat zone is broadened by the penetration of small eddies, the chemical reaction zone remains thin and localized. This feature is captured properly in the current LEM–LES approach. The flame structure and other statistics such as the flame area evolution, curvature, and strain-rate statistics computed using the LEM–LES are also in good agreement with the past DNS studies.     

Three-dimensional direct simulations and structure of expanding turbulent methane flames

Direct numerical simulations (DNS) are ideally suited to investigate in detail turbulent reacting flows in simple geometries. For an increasing number of applications, detailed models must be employed to describe the chemical processes with sufficient accuracy. Despite the huge cost of such simulations, recent progress has allowed the direct numerical simulation of turbulent premixed flames while employing complete reaction schemes. We briefly describe our own developments in this field and use the resulting DNS code to investigate more extensively the structure of premixed methane flames expanding in a three-dimensional turbulent velocity field, initially homogeneous and isotropic. This situation typifies, for example, the initial flame development after spark ignition in a gas turbine or an internal combustion engine. First investigation steps have been carried out at low turbulence levels on this same configuration in the past Symposium, and we build on top of these former results. Here, a considerably higher Reynolds number is considered, the simulation has been repeated twice in to limit the possibility of spurious, very specific results, and several complementary post-processing steps are carried out. Characteristic features concerning the observed combustion regime are presented. We then investigate in a quantitative manner the evolution of flame surface area, global stretch-rate, flame front curvature, flame thickness, and correlation between thickness and curvature. The possibility of obtaining reliable information on flame front curvature from two-dimensional slices is checked by comparison with the exact procedure.     

Velocity of weakly turbulent flames of finite thickness

The velocity increase of a weakly turbulent flame of finite thickness is investigated using analytical theory developed in previous papers. The obtained velocity increase depends on the flow parameters: on the turbulent intensity, on the turbulent spectrum and on the characteristic length scale. It also depends on the thermal and chemical properties of the burning matter: thermal expansion, the Markstein number and the temperature dependence of transport coefficients. It is shown that the influence of the finite flame thickness is especially strong close to the resonance point, when the wavelength of the turbulent harmonic is equal to the cut off wavelength of the Darrieus–Landau instability. The velocity increase is almost independent of the Prandtl number. On the contrary, the Markstein number is one of the most important parameters controlling the velocity increase. The relative role of the external turbulence and the Darrieus–Landau instability for the velocity increase is studied for different parameters of the flow and the burning matter. The velocity increase for turbulent flames in methane and propane fuel mixtures is calculated for different values of the equivalence ratio. The present theoretical results are compared with previous experiments on turbulent flames. In order to perform the comparison, the theoretical results of the present paper are extrapolated to the case of a strongly corrugated flame front using the ideas of self-similar flame dynamics. The obtained theoretical results are in a reasonable agreement with the experimental data, taking into account the uncertainties of both the theory and the experiments. It is shown that in many experiments on turbulent flames the Darrieus–Landau instability is more important for the flame velocity than the external turbulence.     

Partially premixed flamelet in LES of acetone spray flames

An effective partially premixed flamelet model for large eddy simulation (LES) of turbulent spray combustion is formulated. Different flame regimes are identified with a flame index defined by budget terms in a 2-D multi-phase flamelet formulation, and the application in LES of partially pre-vaporized spray flames shows a favorable agreement with experiments. Simulations demonstrate that, compared to the conventional single-regime flamelets, the present partially premixed flamelet formulation shows its ability in capturing the subgrid regime transitions, yielding a well prediction of peak gas temperature and the downstream flame spreading. A propagating premixed flame front is found coupled with a trailing diffusion burning through the spray evaporation, and the spray effect on regime discrimination is manifested with transport budget analysis. A two-phase regime indicator is then proposed, by which the evaporation-dictated regime is properly described. Its intended use will rely on both gas and spray flamelet structures.     

Tomographic reconstruction of the OH*-chemiluminescence distribution in premixed and diffusion flames

A fast tomographic reconstruction device has been developed to detect the two-dimensional distribution of the chemiluminescence of OH^* in the reaction zones of flames. In the set-up, special emphasis was placed on the applicability of the technique to turbulent flames. A spatial resolution of the system, <1–2 mm, and an exposure time of 100–200 μs are required to resolve the chemiluminescence signal of OH^* originating from the folded flame front of a turbulent flame.     

Stratified turbulent Bunsen flames: flame surface analysis and flame surface density modelling

In this paper it is investigated whether the Flame Surface Density (FSD) model, developed for turbulent premixed combustion, is also applicable to stratified flames. Direct Numerical Simulations (DNS) of turbulent stratified Bunsen flames have been carried out, using the Flamelet Generated Manifold (FGM) reduction method for reaction kinetics. Before examining the suitability of the FSD model, flame surfaces are characterized in terms of thickness, curvature and stratification.

All flames are in the Thin Reaction Zones regime, and the maximum equivalence ratio range covers 0.1?φ?1.3. For all flames, local flame thicknesses correspond very well to those observed in stretchless, steady premixed flamelets. Extracted curvature radii and mixing length scales are significantly larger than the flame thickness, implying that the stratified flames all burn in a premixed mode. The remaining challenge is accounting for the large variation in (subfilter) mass burning rate.

In this contribution, the FSD model is proven to be applicable for Large Eddy Simulations (LES) of stratified flames for the equivalence ratio range 0.1?φ?1.3. Subfilter mass burning rate variations are taken into account by a subfilter Probability Density Function (PDF) for the mixture fraction, on which the mass burning rate directly depends. A priori analysis point out that for small stratifications (0.4?φ?1.0), the replacement of the subfilter PDF (obtained from DNS data) by the corresponding Dirac function is appropriate. Integration of the Dirac function with the mass burning rate m=m(φ), can then adequately model the filtered mass burning rate obtained from filtered DNS data. For a larger stratification (0.1?φ?1.3), and filter widths up to ten flame thicknesses, a β-function for the subfilter PDF yields substantially better predictions than a Dirac function. Finally, inclusion of a simple algebraic model for the FSD resulted only in small additional deviations from DNS data, thereby rendering this approach promising for application in LES.     

Parameters influencing the burning rate of laminar flames propagating into a reacting mixture

The laminar flame speed is an important property of a reacting mixture and it is used extensively for the characterization of the combustion process in practical devices. However, under engine-relevant conditions, considerable reactivity may be present in the unburned mixture, introducing thus challenges due to couplings of auto-ignition and flame propagation phenomena. In this study, the propagation of transient, one-dimensional laminar flames into a reacting unburned mixture was investigated numerically in order to identify the parameters influencing the flame burning rate in the conduction-reaction controlled regime at constant pressure. It was found that the fuel chemical classification significantly influences the burning rate. More specifically, for hydrogen flames, the “evolution” of the burning rate does not depend on the initial unburned mixture temperature. On the other hand, for n-heptane flames that exhibit low temperature chemistry, the burning rate depends on the instantaneous temperature and composition of the unburned mixture in a coupled way. A new approach was developed allowing for the decoupling the flame chemistry from the ignition dynamics as well as for the decoupling of parameters influencing the burning rate, so that meaningful sensitivity analysis could be performed. It was determined that the burning rate is not directly affected by fuel specific reactions even in the presence of low temperature chemistry whose effect is indirect through the modification of the reactants composition entering the flame. The controlling parameters include but not limited to mixture conductivity, enthalpy, and the species composition evolution in the unburned mixture.     

A DNS study of the physical mechanisms associated with density ratio influence on turbulent burning velocity in premixed flames

Data obtained in 3D direct numerical simulations of statistically planar, 1D weakly turbulent flames characterised by different density ratios σ are analysed to study the influence of thermal expansion on flame surface area and burning rate. Results show that, on the one hand, the pressure gradient induced within a flame brush owing to heat release in flamelets significantly accelerates the unburned gas that deeply intrudes into the combustion products in the form of an unburned mixture finger, thus causing large-scale oscillations of the burning rate and flame brush thickness. Under the conditions of the present simulations, the contribution of this mechanism to the creation of the flame surface area is substantial and is increased by σ, thus implying an increase in the burning rate by σ. On the other hand, the total flame surface areas simulated at σ = 7.53 and 2.5 are approximately equal. The apparent inconsistency between these results implies the existence of another thermal expansion effect that reduces the influence of σ on the flame surface area and burning rate. Investigation of the issue shows that the flow acceleration by the combustion-induced pressure gradient not only creates the flame surface area by pushing the finger tip into the products, but also mitigates wrinkling of the flame surface (the side surface of the finger) by turbulent eddies. The latter effect is attributed to the high-speed (at σ = 7.53) axial flow of the unburned gas, which is induced by the axial pressure gradient within the flame brush (and the finger). This axial flow acceleration reduces the residence time of a turbulent eddy in an unburned zone of the flame brush (e.g. within the finger). Therefore, the capability of the eddy for wrinkling the flamelet surface (e.g. the side finger surface) is weakened owing to a shorter residence time.     

Resonance of a turbulent flame in a high-frequency acoustic wave

Resonance of a weakly turbulent flame in a high-frequency acoustic wave is obtained. Because of the resonance, an acoustic wave may increase noticeably the amplitude of flame wrinkles, and the respective increase in propagation velocity of the turbulent flame front becomes larger by a factor of 10-20. The effect of resonance is especially important for turbulent flames with realistic thermal expansion propagating in a closed burning chamber, which may account for considerable scattering of experimental results on turbulent flame velocity.     

Multi-scalar measurements in a premixed swirl burner using 1D Raman/Rayleigh scattering

Instantaneous measurements of temperature, equivalence ratio, and major species were performed along a one-dimensional probe volume using simultaneous Raman/Rayleigh scattering in an unconfined turbulent lean-premixed swirling methane/air flame. Temperature was determined from Rayleigh scattering and the major species, CO₂, O₂, N₂, CH₄, H₂O, and H₂ from Raman scattering. Effective Rayleigh cross-sections were corrected using the local chemical composition obtained from Raman scattering. These experiments were conducted to investigate the compositional structure of a lean-premixed swirling flame in detail and to complement previous measurements of the underlying flow field. The flame was classified within a revised regime diagram at the cross-over between corrugated flames and thin reaction zones. Instantaneous temperature profiles varied significantly showing shapes ranging from laminar-like flamelets to mixing between reacted fluid elements and secondary air. Different thermo-kinetic states could be assigned to the inner and outer recirculation zones and to the inner and outer mixing layers. Linked to published velocity data of this flame, the present multi-scalar data are useful for validation of numerical simulations.     

Turbulent propagation of premixed flames in the presence of Darrieus–Landau instability

We investigate the role played by hydrodynamic instability in the wrinkled flamelet regime of turbulent combustion, where the intensity of turbulence is small compared to the laminar flame speed and the scale large compared to the flame thickness. To this end the Michelson–Sivashinsky (MS) equation for flame front propagation in one and two spatial dimensions is studied in the presence of uncorrelated and correlated noise representing a turbulent flow field. The combined effect of turbulence intensity, integral scale, and an instability parameter related to the Markstein length are examined and turbulent propagation speed monitored for both stable planar flames and corrugated flames for which the planar conformation is unstable. For planar flames a particularly simple scaling law emerges, involving quadratic dependence on intensity and a linear dependence on the degree of instability. For corrugated flames we find the dependence on intensity to be substantially weaker than quadratic, revealing that corrugated flames are more resilient to turbulence than planar flames. The existence of a threshold turbulence intensity is also observed, below which the corrugated flame in the presence of turbulence behaves like a laminar flame. We also analyze the conformation of the flame surface in the presence of turbulence, revealing primary, large-scale wrinkles of a size comparable to the main corrugation. When the integral scale is much smaller than the characteristic corrugation length we observe, in addition to primary wrinkles, secondary small-scale wrinkles contaminating the surface. The flame then acquires a multi-scale, self-similar conformation, with a fractal dimension, for one-dimensional flames, plateauing at 1.23 for large intensities. The existence of an intermediate integral scale is also found at which the turbulent speed is maximized. When two-dimensional flames are subject to turbulence, the primary wrinkling patterns give rise to polyhedral-cellular structures which bear a very close resemblance to those observed in experiments on hydrodynamically unstable expanding spherical flames.     

Effects of Lewis number,density ratio and gravity on burning velocity and conditional statistics in stagnating turbulent premixed flames

DNS is performed to analyse the effects of Lewis number (Le), density ratio and gravity in stagnating turbulent premixed flames. The results show good agreement with those of Lee and Huh (Combustion and Flame, Vol. 159, 2012, pp. 1576–1591) with respect to the turbulent burning velocity, S_T, in terms of turbulent diffusivity, flamelet thickness, mean curvature and displacement speed at the leading edge. In all four stagnating flames studied, a mean tangential strain rate resulting in a mean flamelet thickness smaller than the unstretched laminar flame thickness leads to an increase in S_T. A flame cusp of positive curvature involves a superadiabatic burned gas temperature due to diffusive–thermal instability for an Le less than unity. Wrinkling tends to be suppressed at a larger density ratio, not enhanced by hydrodynamic instability, in the stagnating flow configuration. Turbulence is produced, resulting in highly anisotropic turbulence with heavier unburned gas accelerating through a flame brush by Rayleigh–Taylor instability. Results are also provided on brush thickness, flame surface density and conditional velocities in burned and unburned gas and on flame surfaces to represent the internal brush structures for all four test flames.     

Two-dimensional imaging of glyoxal (C2H2O2) in acetylene flames using laser-induced fluorescence

2 H₂O₂). Laser-induced fluorescence spectra from glyoxal vapor using the same excitation wavelength of 428 nm showed the same strongest lines as the signal from the flame. Glyoxal was visualized in two different modes; two-dimensional imaging and a spatial-spectral mode where spectra were obtained at different spatial positions in the flame simultaneously. For the premixed laminar rich flame it is shown that glyoxal is produced early in the flame, before the signals for C₂ and CH appear. For the turbulent non-premixed flames it is shown that glyoxal is produced in a layer on the fuel rich side of the flames. Here the fuel is premixed with ambient air. This layer is thin and has a high spatial resolution. The general trend was that the glyoxal signal appeared in regions with a lower temperature compared with the emission from C₂ and CH. The imaging of glyoxal in turbulent acetylene flames is a promising tool for achieving new insight into flame phenomena, as it gives very good structural information on the flame front. Tests so far do not indicate that the detected glyoxal is a result of photo-production. To our knowledge, this is the first detection of glyoxal in flames using laser-induced fluorescence. Received: 19 December 1996/Revised version: 26 May 1997