Stability-indicating high performance thin layer chromatographic determination of sulfanilamide in human urine

A simple, sensitive, selective, precise and stability-indicating high-performance thin-layer chromatographic (HPTLC) method was developed and applied to human urine for the densitometric determination of sulfanilamide. A mixture of chloroform-ethyl acetate-xylene (2.5: 4.0: 1.0, v/v/v) was used as a mobile phase. The system was found to give compact spots for sulfanilamide (retardation factor, R _f = 0.21±0.02). The linear regression analysis data for the calibration plots showed good linear relationship with r ² = 0.9970 ± 0.0003 and r ² = 0.9947 ± 0.020 within the concentration range of 50–250 ng per spot and 100–1000 ng per spot with respect to peak area, respectively. The limit of detection (LOD) and quantification (LOQ) were 8 and 25 ng per spot, respectively. Sulfanilamide was subjected to acid and alkali hydrolysis, oxidation, dry heat and wet heat treatment. According to the International Conference on Harmonization (ICH) guidelines the method was validated for precision, recovery and robustness. The ultraviolet (UV) spectra of the degradation products which had different spectra from sulfanilamide were also recorded. The article is published in the original.     

Stability indicating high-performance thin-layer chromatographic determination of nelfinavir mesylate as bulk drug and in pharmaceutical dosage form

A sensitive, selective, precise and stability indicating high-performance thin-layer chromatographic method of analysis of nelfinavir mesylate both as a bulk drug and in formulations was developed and validated. The method employed TLC aluminium plates precoated with silica gel 60F-254 as the stationary phase. The solvent system consisted of toluene-methanol-acetone (7:1.5:1.5, v/v/v). This system was found to give compact spots for nelfinavir mesylate (R_f value of 0.45±0.02). Nelfinavir mesylate was subjected to acid and alkali hydrolysis, oxidation, dry heat treatment and photodegradation. Also the peaks of degraded products were well resolved from the pure drug with significantly different R_f values. Densitometric analysis of nelfinavir mesylate was carried out in the absorbance mode at 250 nm. The linear regression analysis data for the calibration plots showed good linear relationship with r²=0.999±0.002 in the concentration range of 1000-6000 ng per spot. The mean value of correlation coefficient, slope and intercept were 0.999±0.002, 0.014±0.001 and 21.73±1.26, respectively. The method was validated for precision, robustness and recovery. The limits of detection and quantitation were 60 and 140 ng per spot, respectively. Statistical analysis proves that the method is repeatable and selective for the estimation of the said drug. As the method could effectively separate the drug from its degradation products, it can be employed as a stability indicating one.     

Stability indicating HPTLC determination of clopidogrel bisulphate as bulk drug and in pharmaceutical dosage form

A sensitive, selective, precise and stability indicating high-performance thin layer chromatographic method of analysis of clopidogrel bisulphate both as a bulk drug and in formulations was developed and validated in pharmaceutical dosage form. The method employed TLC aluminium plates precoated with silica gel 60F-254 as the stationary phase. The solvent system consisted of carbon tetrachloride-chloroform-acetone (6:4:0.15, v/v/v). This system was found to give compact spots for clopidogrel bisulphate (R_f value of 0.30±0.01). Clopidogrel bisulphate was subjected to acid and alkali hydrolysis, oxidation, photodegradation and dry heat treatment. Also the degraded products were well separated from the pure drug. Densitometric analysis of clopidogrel bisulphate was carried out in the absorbance mode at 230 nm. The linear regression data for the calibration plots showed good linear relationship with r²=0.999±0.001 in the concentration range of 200-1000 ng. The mean value of correlation coefficient, slope and intercept were 0.999±0.001, 0.093±0.011 and 8.83±0.99, respectively. The method was validated for precision, accuracy, ruggedness and recovery. The limits of detection and quantitation were 40 and 120 ng per spot, respectively. The drug undergoes degradation under acidic and basic conditions, oxidation and dry heat treatment. All the peaks of degraded product were resolved from the standard drug with significantly different R_f values. This indicates that the drug is susceptible to acid-base hydrolysis, oxidation and dry heat degradation. Statistical analysis proves that the method is reproducible and selective for the estimation of the said drug. As the method could effectively separate the drug from its degradation products, it can be employed as a stability indicating one.     

Stability‐indicating HPTLC method for quantitative estimation of silybin in bulk drug and pharmaceutical dosage form

In the present study a novel stability‐indicating high‐performance thin‐layer chromatography (HPTLC) method for quantitative determination of silybin in bulk drug and nanoemulsion formulation has been developed and validated on silica using solvent chloroform–acetone–formic acid (9 : 2 : 1 v/v/v) (R_f of silybin 0.46 ± 0.05) in the absorbance mode at 296 nm. The method showed a good linear relationship (r² ± 0.999) in the concentration range 25–1500 ng per spot. It was found to be linear, accurate, precise, specific, robust and stability‐indicating and can be applied for quality control and standardization of several multi‐component hepatoprotective formulations as well as for stability testing of different dosage forms. The method proposed was also used to investigate the kinetics of acidic and alkaline degradation processes by quantification of drug at different temperature to calculate the activation energy and half‐life for silymarin degradation. Copyright © 2009 John Wiley & Sons, Ltd     

Development and validation of a reversed-phase HPLC method with post-column iodine-azide reaction for the determination of thioguanine

A high-performance liquid chromatographic method of reversed-phase with a post-column iodineazide reaction has been developed and validated for the determination of thioguanine. Isocratic elution was performed on a column of C₁₈ using acetonitrile- water-sodium azide solution (1.5%; pH 6.5) 16: 34: 50 (v/v/v) as a mobile phase with flow-rate of 0.5 mL/min. Monitoring of unreacted iodine in post-column iodine-azide reaction induced by thioguanine resulted in its detection at 350 nm. The method applied to thioguanine was linear within the scope of values 8–100 nM (r ² > 0.9988). The relative standard deviation (RSD < 4.2%) and the recovery (>96%) prove that the intra-day precision and the accuracy were satisfactory. The lower limits of detection (LLD) and quantification (LLQ) of thioguanine were established at the levels of 6 and 8 nM, respectively. The elaborated method was validated and applied to thioguanine determination in tablets.     

Development of an HPTLC‐based diagnostic method for invasive aspergillosis

A rapid, sensitive and specific high‐performance thin‐layer chromatographic (HPTLC) method was developed and validated for determination of gliotoxin in Aspergillus infected immunocompromised patients with invasive aspergillosis (IA). Densitometric analysis of gliotoxin was carried out in the absorbance mode at 254 nm after single‐step extraction with chloroform. The method uses TLC aluminum plates pre‐coated with silica gel 60F‐254 as a stationary phase and toluene–isoamyl alcohol–methanol (10:0.5:0.5, v/v/v) as mobile phase, which gives compact spot of gliotoxin (R_f = 0.51). The calibration curve was linear (r² ≥ 0.994) between peak area and concentration in the tested range of 100–1000 ng spot^?1 with minimum detectable range 0.025 ng μ^?1 of serum sample. The mean ± SD value of slope and intercept of the standard chromatogram of gliotoxin were found to be 523.2 ± 1.555635 and 915.8 ± 30.68843, respectively. The developed method is simple, rapid, precise and less costly than earlier diagnostic methods, and different serum samples can be run on a single TLC plate for comparative analysis. The proposed method can be used to analyze gliotoxin in patient serum for easy, rapid and cost‐effective diagnosis of IA. Copyright © 2009 John Wiley & Sons, Ltd.     

Stability-Indicating HPTLC Method for the Determination of Tamsulosin in Pharmaceutical Dosage Forms

A simple, sensitive, selective, precise and stability indicating high-performance thin-layer chromatographic method was developed for the determination of tamsulosin (TAM) in bulk and tablet formulation. Validation was carried out in compliance with International Conference on Harmonization guidelines. The method employed thin-layer chromatography aluminium plates pre-coated with silica gel 60F₂₅₄ as the stationary phase and the mobile phase consisted of acetonitrile/methanol/dichloromethane (2.0: 1.0: 2.0, v/v/v). This solvent system was found to give compact spots for tamsulosin (R _f = 0.27 ± 0.02). Densitometric analysis of TAM was carried out in the absorbance mode at 286 nm. Linear regression analysis showed good linearity (r ² = 0.9993) with respect to peak area in the concentration range of 300–800 ng per band. The method was validated for precision, accuracy, ruggedness and recovery. Limits of detection and quantitation were 8.49 and 25.72 ng per band, respectively. TAM was subjected to acid and alkali hydrolysis, oxidation, photo degradation, dry heat and wet heat treatment. The drug underwent degradation under acidic, basic and photolytic conditions. The degraded products were well separated from the pure drug. Statistical analysis proved that the developed method, used for quantification of TAM as a bulk drug and present in pharmaceutical tablets, was reproducible and selective.

     

Ein einfacher Weg zu α-substituierten (E)-3-Oxo-1-alkenylphosphonsäureestern

Zusammenfassung -Substituierte -Acylvinylphosphonate3 mitE-Konfiguration [R ²CO-CH=C(R ¹)-P(O)(OR)₂], werden in guten Ausbeuten durchWittig-Reaktion von Acylphosphonsäureestern1 [R ¹CO-P(O)(OR)₂,R ¹=Alkyl oder Aryl] mit (2-Oxoalkyliden)triphenylphosphoranen2 [R ²CO-CH=PPh ₃,R ²=Alkyl, O-Alkyl oder CH₂ X (X=Br, OMe, CO₂ Et)] erhalten.

---

A convenient route to -substituted dialkyl (E)-3-oxo-1-alkenylphosphonates

-Substituted dialkyl (E)--acylvinylphosphonates [R ²CO-CH=C(R ¹)-P(O)(OR)₂,3], are easily obtained in good yields byWittig-reaction of dialkyl acylphosphonates1 [R ¹CO-P(O)(OR)₂,R ¹=alkyl or aryl) with 2-oxoalkylidene triphenylphosphoranes2 [R ²CO-CH=PPh ₃,R ²=alkyl, O-alkyl and CH₂ X (X=Br, OMe, CO₂ Et)].

     

Transition metal impurities in wide gap materials: are the electronic properties well described through the ligand field theory?

In the traditional ligand field theory the electronic properties due to a transition metal (TM) impurity, M, in an insulator are explained only in terms of the MX _N complex formed with the N nearest anions. This work is aimed at emphasizing the role played by the electrostatic potential, V _R (r), exerted by the rest of lattice ions upon the localized electrons of the TM complex. This potential, neglected in the traditional ligand field theory, is shown to play a key role when comparing the electronic properties of the same TM complex but embedded in two lattices which are not isomorphous even if both are cubic. As a relevant example it is shown that the different 10 Dq values exhibited by in the normal perovskite KMgF₃ (10 Dq = 14,100 cm⁻¹) and in the inverted perovskite BaLiF₃ (10 Dq = 16,720 cm⁻¹) can hardly be understood only through a distinct Cr³⁺–F⁻ distance. In contrast such a difference is shown to come mainly from the different shape of V _R (r) in these two cubic lattices. the importance of this internal electric field is pointed out to grow when comparing two host lattices with the same ligand and coordination number but very different symmetry. This situation is found in the case of ruby (Al₂O₃ : Cr³⁺) and emerald (Be₃Si₆Al₂O₁₈ : Cr³⁺) where V _R (r) is behind the different colours exhibited by such gemstones. For the sake of clarity a brief discussion on the foundations of the ligand field theory is reported in the present work as well. Contribution to the Serafin Fraga Memorial Issue.     

Stability-Indicating Chromatographic Methods for Simultaneous Determination of Mosapride and Pantoprazole in Pharmaceutical Dosage Form and Plasma Samples

Simple, sensitive, selective, precise, and stability-indicating thin-layer chromatography (TLC) and high-performance liquid chromatography (HPLC) methods for the determination of mosapride and pantoprazole in pharmaceutical tablets were developed and validated as per the International Conference on Harmonization guidelines. The TLC method employs aluminum TLC plates precoated with silica gel 60F₂₅₄ as the stationary phase and ethyl acetate/methanol/toluene (4:1:2, v/v/v) as the mobile phase to give compact spots for mosapride (R _f 0.73) and pantoprazole (R _f 0.45) separated from their degradation products; the chromatogram was scanned at 276 nm. The HPLC method utilizes a C18 column and a mobile phase consisting of acetonitrile/methanol/20 mM ammonium acetate (4:2:4, v/v/v) at a flow rate of 1.0 mL min⁻¹ for the separation of mosapride (t _R 11.4) and pantoprazole (t _R 4.4) from their degradation products. Quantitation was achieved with UV detection at 280 nm. The same HPLC method was successfully used in performing calibrations in lower concentration ranges for both drugs in human plasma using ezetimibe as internal standard. The methods were validated in terms of accuracy, precision, linearity, limits of detection, and limits of quantification. Mosapride and pantoprazole were exposed to acid hydrolysis and then analyzed by the proposed methods. As the methods could effectively separate the drugs from their degradation products, these techniques can be employed as stability-indicating methods that have been successively applied to pharmaceutical formulations without interference from the excipients. Moreover the HPLC method was successfully used in the determination of both drugs in spiked human plasma.

     

LC Determination of Gemfibrozil in Tablets

A simple, selective, precise and accurate reversed phase-HPLC assay for analysis of gemfibrozil in tablets was developed and validated. Separation and quantification were achieved on a Phenomenex C₁₈ column under isocratic conditions using a mobile phase (methanol:water, 80:20, v/v) maintained at 1.1 mL min⁻¹. UV-detection was at 280 nm. Atorvastatin was selected as an internal standard. The standard curves were linear over the range of 0.5–3.0 μg mL⁻¹ (r > 0.999). The limits of detection and quantification were 0.20 and 0.51 μg mL⁻¹, respectively. The recoveries for gemfibrozil were above 99.01%. The intra-day and inter-day precision (RSD) for gemfibrozil were below 1.74 and 1.83%, respectively. No chromatographic interferences from the tablet excipients were found. The results of the developed procedure in tablets were compared with those of the reference method to assess gemfibrozil content. Statistical comparison of the results with the reference method using spectrofluorimetric method showed excellent agreement and proved no significant difference in accuracy and precision. This HPLC method is fast and simple for the analysis of gemfibrozil in pharmaceutical preparations.     

A Validated Stability-Indicating TLC Method for Determination of Forskolin in Crude Drug and Pharmaceutical Dosage Form

A simple, accurate, selective, precise, economical and stability-indicating high-performance thin-layer chromatographic method for analysis of forskolin in crude drug and in pharmaceutical dosage form was developed and validated. The method was developed on TLC aluminium plates precoated with silica gel 60F-254 using solvent system benzene:methanol (9:1, v/v), which gives compact spot of forskolin (R _f value 0.25 ± 0.02). Densitometric analysis of forskolin was carried out in the absorbance mode at 545 nm after spraying with anisaldehyde sulphuric acid. The linear regression analysis data for the calibration plots showed good linear relationship with r = 0.994 and 0.994 with respect to peak height and peak area, respectively, in the concentration range 100–1,000 ng per spot. The limits of detection and quantification were 8.1 and 26.9 ng per spot, respectively. The proposed method was applied for determination of forskolin in Coleus forskohlii root and in capsule dosage forms, which showed 0.18 and 0.57% w/w of forskolin. Forskolin was subjected to acid and alkali hydrolysis, oxidation, photodegradation and heat degradation. It was observed that the drug is susceptible to acid, base hydrolysis, oxidation, photo-oxidation and heat degradation. Statistical analysis proves that the method is repeatable, selective and accurate for the estimation of forskolin in crude drug and in pharmaceutical dosage forms. The developed method effectively resolved the forskolin from components of C. forskohlii root, from excipients of capsule as well as the degradation products of forskolin hence, it can be employed for routine analysis and as a stability-indicating method.     

Development and validation of RP-HPLC method for simultaneous estimation of prednicarbate,mupirocin and ketoconazole in topical dosage forms

A simple and accurate reversed-phase high-performance liquid chromatography (RP-HPLC) method was developed and validated for simultaneous estimation of prednicarbate (PC), mupirocin (MP) and ketoconazole (KT) in topical dosage forms. This combination is preferred for topical delivery of anti-inflammatory, antibacterial and antifungal agents for treatment of various skin disorders. The proposed RP-HPLC method utilizes a Hypersil GOLD C18, 5 μm, 250 mm × 4.6 mm i.d. column, mobile phase consisting of methanol-water (80: 20, v/v) adjusted to pH 5.0 with orthophosphoric acid in isocratic mode at the flow rate of 0.5 mL/min and UV detection at 243 nm. The method does not require any specific sample preparation except extraction of active pharmaceutical ingredients from the developed topical emulgel formulations using dichloromethane. Linearity was found in the range of 0.05–0.3 mg/L for PC and 0.4–2.4 mg/L for each of MP and KT with R ² > 0.999. The method is precise with low RSD%, accurate (overall average recovery yields: 99.92% for PC, 99.44% for MP and 99.74% for KT) and selective. Due to its simplicity and accuracy, the method is suitable for simultaneous analysis of PC, MP and KT in topical dosage forms.     

Validated Chiral LC Method for the Enantiomeric Separation of Palonosetron Hydrochloride

A new and accurate chiral liquid chromatographic method has been developed for the separation of palonosetron hydrochloride (PALO) and its (R,R)-enantiomer in bulk drug samples with an elution time of about 20 min. The chromatographic separation was carried out by normal phase chromatography using an immobilized cellulose based chiral stationary phase (Chiralpak-IC) with a mobile phase composed of n-hexane:ethanol:1,4 dioxane:trifluoroacetic acid:diethylamine (65:30:5:0.3:0.3, v/v) pumped at a flow rate of 1.0 mL min⁻¹. The resolution (R _s ) between the enantiomers was found to be greater than 3.0 and interestingly the (R,R)-enantiomer was eluted prior to the (S,S)-enantiomer (PALO) in the developed method. Mobile phase additives, trifluoroacetic acid and diethylamine played a key role in achieving chromatographic resolution between the enantiomers and also in enhancing chromatographic efficiency. The limit of detection (LOD) and limit of quantification (LOQ) of the (R,R)-enantiomer were found to be 0.03 and 0.1 μg respectively for 10 μL injection volume. The developed method shows excellent linearity (r ² > 0.999) over a range of LOQ to 0.3% for the (R,R)-enantiomer. The percentage recovery of the (R,R)-enantiomer in bulk drug samples ranged from 97.2 to 102.3 revealing good sensitivity of the developed method. Robustness studies were also carried out on the developed method.

     

New [Ti(η5-C5H5)Cl2(OR)] complexes. Crystal and molecular structure of η5-Cyclopentadienyl(cyclohexoxy)titanium(IV) dichloride

Summary A series of new compounds with molecular formula [Ti(⁵-C₅H₅)Cl₂(OR)] (R=C₆H₁₁ (cyclohexyl,1), CH₂CH(CH₃)₂ (2), CH(C₂H₅)₂ (3), and CH₂C₆H₅ (4)) has been obtained by the reaction of [Ti(⁵-C₅H₅)Cl₃] with the appropriate alcohol. All complexes were characterized by elemental analysis and by IR and¹H NMR spectroscopy. The structure of1 was determined by X-ray diffraction studies; crystal data: triclinic,a=11.334(2),b=13.590(2),c=12.237(2) Å, =113.501(5), =118.182(5), =101.993(6),V=1328.2(4) ų,T=298K, space P1,Z=4, two crystallographically independent molecules in the unit cell. FinalR andR _w values are 0.0583 and 0.0632, respectively. Compound1 exhibits surprisingly short Ti-Cl and Ti-O distances, suggesting strong donation by the chloride and in particular by the alkoxide ligand. The Ti-O-C angle is unusually large.

---

Neue [Ti(⁵-C₅H₅)Cl₂(OR)]-Komplexe. Kristall- und Molekülstruktur von ⁵-Cyclopentadienyl(cyclohexoxy)titan(IV) Dichlorid

Zusammenfassung Durch Umsetzung von [Ti(⁵-C₅H₅)Cl₃] mit dem geeigneten Alkohol wurde eine Reihe von neuen Verbindungen der Formel [Ti(⁵-C₅H₅)(OR)] (R=C₆H₁₁ (cyclohexyl,1), CH₂CH(CH₃)₂ (2), CH(C₂H₅)₂ (3) und CH₂C₆H₅ (4)) erhalten. Alle Komplexe wurden elementaranalytisch sowie IR- und¹H-NMR-spektroskopisch charakterisiert. Die Struktur von1 wurde röntgenographisch bestimmt; Kristalldaten: triklin,a=11.334(2),b=13.590(2),c=12.237(2) Å, =113.501(5), =118.182(5), =101.993(6),V=1328.2(4) ų,T=298K, Raumgruppe P1,Z=4, zwei kristallographisch unabhängige Moleküle in der Elementarzelle; abschließendeR-Werte:R=0.0583 undR _w=0.0632. Verbindung1 zeigt überraschend kurze Ti-Cl- und Ti-O-Abstände; dies deutet auf eine starke -Elektronendonorwirkung des Chlorid- und vor allem des Alkoxidliganden hin. Der Ti-O-C-Bindungswinkel ist ungewöhnlich groß.

     

Development and validation of TLC‐densitometric method for determination of lipid A adjuvant as a bulk and in solid fat nanoemulsions

A simple, sensitive, selective and precise high‐performance thin‐layer chromatographic method was developed for determination of lipid A (MPLA) adjuvant as a bulk and in solid fat nanoemulsions. Chromatographic separations were performed on thin‐layer chromatography aluminum plates precoated with silica gel 60 F‐254 as stationary phase and chloroform–methanol–ethyl acetate solution (10:2:4, v/v/v) as mobile phase. With this solvent system, compact spots for MPLA at R_f value 0.80 ± 0.02 were obtained. Densitometric analysis of MPLA was carried out in absorbance mode at 357 nm. Linear regression analysis for the calibration plots showed good linear relationship with r = 0.9996 in the concentration range of 20–100 ng/spot. The mean values (±SD) of slope and intercept were found to be 7.355 ± 0.006 and 109.52 ± 0.170, respectively. Limits of detection (LOD) and quantitation (LOQ) were observed at 3.096 and 9.382 ng/spot, respectively.The method was validated for precision, accuracy, robustness and recovery as per the International Conference on Harmonization guidelines. Statistical analysis proved that the developed method for quantification of MPLA as a bulk and in solid fat nanoemulsions is reproducible, selective and economical. This method could be applied for quantitative assay of MPLA in lipid‐based vaccine formulations. Copyright © 2015 John Wiley & Sons, Ltd.     

Changes of the Cu electrode real surface area during the process of electroless copper plating

The surface area (nanoscale roughness) of copper coatings deposited from electroless plating solutions containing Quadrol, L(+)- and DL(∓)-tartrate as Cu(II) ion ligands was measured using underpotential deposition thallium monolayer formation. Surface roughness of Cu coatings depends on the plating solution pH and the Cu(II) ligand, and varies over a wide range. In L(+)-tartrate and Quadrol solutions (pH 12.5–13.3) the roughness factor R _f is low and is equal to 2–3 and 4–6, respectively (substrate: electrodeposited Cu; R _f=2.2). Cu coatings of higher surface area are obtained in DL(∓)-tartrate (pH 12.3–12.7) and Quadrol (pH 12.0) solutions: R _f reaches 20–30. The correlation between R _f and Cu deposition rate was found in L(+)-tartrate solution. The Cu surface area changes are discussed in terms of partial electrochemical reactions of the autocatalytic Cu deposition process, and the decisive role of cathodic Cu(II) reduction from adsorbed Cu(II) complex species. Received: 2 November 1999 / Accepted: 22 February 2000     

Comparative Study of the Determination of Parabens in Shampoos by Liquid Chromatography with Amperometric and Coulometric Detection

The simultaneous determination of four para‐hydroxybenzoic acid esters (parabens) in shampoos was studied by liquid chromatography (LC) with amperometric (LC‐AD) and coulometric (LC‐CD) detection. The parabens were separated on an ODS C18 reversed column by isocratic elution with a mobile phase based on methanol‐0.1 M acetic acid (60 : 40%, v/v) with 0.02 M NaClO₄ at a flow rate of 0.8 mL min^?1. The limit of detection (S/N>3) for the analytes was in the 15–25 pg (injected mass) range at an applied potential of 1.20 V vs. Ag/AgCl using the LC‐AD and in the 2–3 pg range at a potential of 0.790 V vs. Pd using the LC‐CD. The peak ratio of the internal standard peak (IS: 4‐hydroxybenzoic acid sec‐butyl ester) versus the analyte peak was found to be related to the amount injected from 0.1 ng to 100ng (r=0.996–0.999) with the LC‐AD and from 0.050 ng to 100 ng range (r=0.999–1.000) with the LC‐CD. The relative standard deviation (RSD, n=10) was comprised between 1.8 to 3.5% by LC‐AD ( 5 ng injected) and between 2.0 to 2.4% by LC‐CD (0.5 ng injected). The determination of four most used parabens in ten different shampoos was successfully realized.     

原子配分参数、配分连接性指数及其应用

结构决定性质，性质反映结构，这是化学、生物学等学科的一条基本规律。因此，分子的微观结构与性质之间存在着密切关系。物质的理化性质、生物活性等数据的获取，迄今主要来自于实验。如能建立结构与性能之间的数量关系用以估算与预测分子的性质，这无疑是一项十分有意义的工作。拓扑指数法以其计算简单、准确性高、应用范围广而在上述领域中发挥重要作用犤１～４犦。拓扑指数是对分子结构进行的定量描述，使分子之间的结构差异定量化。自Wiener提出第一个拓扑指数（W）犤５犦以来，迄今已有２００余种拓扑指数问世。其中一部分能够有效地…     

Influence of the nature of ligands in iridium complexes with C60 fullerene and ·P(O)(OPri)2, ·CMe3, and ·CCl3 radicals on regioselectivity of addition and stability of spin-adducts formed: an EPR study

The addition of ^·P(O)(OPrⁱ)₂ (R¹), ^·CMe₃ (R²), and ^·CCl₃ (R³) radicals to metallofullerenes (η²-C₆₀)IrH(CO)(CNBu^t)₂(o-HCB₁₀H₉CCH₂PPh₂-B,P) (1), (η²-C₆₀)IrH(CO)(DIOP) (DIOP is (4R,5R)-(+)-4,5-bis(diphenylphosphinomethyl)-2,2-dimethyl-1,3-dioxolane, 2), and (η²-C₆₀)IrH(CO)(PPh₃)₂ (3) was studied by EPR spectroscopy. A stability study of spin adducts (SAs) of R¹ radicals with complexes 1 and 2 showed that when the reactions are initiated by illumination with 366-nm light, the EPR spectra exhibit only signals of those isomers that are formed upon attack of the R¹ radicals on the carbon atoms of the cis-1 and cis-2 bonds (i.e., carbon atoms of the fullerene hemisphere to which the metallofragment is attached). Investigations of the reactions of R² and R³ radicals with complexes 1–3 initiated with 366-nm light made it possible to detect (i) regioisomers formed by adding these radicals to carbon atoms of the cis-n bonds and (ii) SAs formed by adding the radicals to carbon atoms of other bonds in complexes 1–3. The hyperfine structure of the EPR spectrum essentially depends on the spatial structure of substituents at the metal atom and allows individual regioisomers of not only phosphoryl radicals, but also carbon-centered radicals R² and R³ with metallofullerenes 1–3 to be identified. The rate constants for addition of R² and R³ radicals to complexes 2 and 3 were determined. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 7, pp. 1302–1309, July, 2007.