Dispersion and Structure Studies of Molybdenum Oxide on Anatase TiO2

X-ray photoelectron spectroscopy (XPS) and extended X-ray absorption fine structure (EXAFS) were used to characterize the structure of the mixture of molybdenum oxide and anatase calcined at 723 K. The resuits indicate that molybdenum oxide can disperse onto the surface of anatase (TiO2) and the dispersion threshold is 11.2 mg in per gram of MoO3 or 4.8 Mo atoms/nm^2 TiO2. When the coment of MoO3 is below the dispersion threshold, MoO3 species is in highly dispersed state interacting strongly with TiO2 support and in discrete tetrahedral coordination. [MoO4], on the surface of TiO2. When the MoO3 loading is above this value, MoO3 exists in both dispersed phase and crystalline phase. MoO3 in dispersed phase is still a discrete [MoO4] tetrahedron; MoO3 in crystal phase is in octahedral coordination.     

SO42-改性后的TiO2(锐钛和/或金红石)表面上MoO3的分散性质研究

采用红外(IR)、拉曼(Raman)、X-射线衍射(XRD)、程序升温还原(TPR)等方法考察了经硫酸根改性后的金红石(SR)与锐钛矿(SA)的混合比例变化时的负载型催化剂，MoO₃ / TiO₂(SR+SA)，的一些物理化学性质(如活性组分MoO₃的分散行为、表面酸碱性、氧化还原性)的变化规律。结果表明：对于MoO₃ / TiO₂(SR+SA)样品，低含量MoO₃表面分散时倾向于优先与混合载体中的改性金红石(SR)发生作用；TiO₂载体表面SO₄^2-的存在，使得载体表面产生了新的酸性位，导致样品中表面分散的钼物种主要以聚合八面体状态存在。     

The structure and catalytic activity of anatase and rutile titania supported manganese oxide catalysts for selective catalytic reduction of NO by NH3

The structure and catalytic properties of anatase and rutile supported manganese oxide catalysts prepared by impregnation method have been studied by using X-ray diffraction (XRD), laser Raman spectroscopy (LRS), X-ray photoelectron spectroscopy (XPS), H(2) temperature-programmed reduction (H(2)-TPR) and BET surface area measurements combined with activity testing of selective catalytic reduction (SCR) of NO by NH(3). It has been shown that the manganese oxide loadings on the two TiO(2) supports exert great influences on the SCR activity. For the rutile supported manganese oxide catalysts, increasing manganese oxide loading leads to the increase of reducibility of dispersed manganese oxide species and the rate constant k, which reaches a maximum around 9.6 × 10(-6) mol g(Mn)(-1) s(-1) at 0.5 mmol Mn per 100 m(2) TiO(2). When the manganese oxide loading is beyond this value, the existence of amorphous MnO(x) multiple layers will certainly reduce the ratio of manganese oxide species exposed on the surface and the reducibility of dispersed manganese oxide species, resulting in the rapid decrease of rate constant k. The LRS and XPS results have revealed that for the anatase supported manganese oxide catalysts manganese oxide species exist in Mn(+4) as a major species with Mn(+3) species and partially undecomposed Mn-nitrate as the minor species. Under the SCR reaction conditions, Mn(+3) species on anatase are oxidized to Mn(+4) species, inserting in the surface of anatase and promoting the anatase-to-rutile transformation in the surface layers of the anatase support. Since these Mn(4+) cations are actually dispersed on the support with a rutile shell-anatase core structure and its concentration is very near to that of MnO(x)/TiO(2) (R) catalyst, the relation between the rate constant k and the MnO(x) loading on the anatase support is similar to that on the rutile support, and that the rate constant k values for anatase and rutile supported manganese oxide catalysts are very close at the same MnO(x) loading.     

MoO_3、NiO、ZnO在小表面金红石上的分散行为

氧化物、盐类在氧化物载体表面的自发分散是一种广泛存在的现象，文献中已报导过大量氧化物和盐类在高比表面载体上分散的研究结果［'－3］TIO。作为一种较新型的载体，与Y－AI。O。、硅胶等传统载体相比，有许多不同特性．活性组分在TIO。表面的分散状态及所得催化剂的性能已有不少报导［'－'］，但所用的TIOZ主要是较高比表面的锐钛矿型TIOZ（刘金红石型TIO。（r）和锐钛矿型TIOZ（a）的结构不同，它是高温生成相，比表面较小［'］．氧化物在金红石上的分散行为仍未见报导．我们制备了三种具有不同比表面的TIO水），系统地研…     

MoO3、NiO、ZnO在小表面金红石上的分散行为

Dispersion of MoO3, NiO, ZnO on rutile TiO2 with low specific surface area was studied with Mercury Porosimeter, SEM, XPS and Ammonia Extraction method. The dispersion thresholds of MoO3, NiO, ZnO on three rutile TiO2 carriers were obtained with XPS, and com-pared with those on anatase TiO2 with high specific surf are area. Ammonia Extraction method was used to identify the surface oxide species interarting with support surface in different strength and it was found that the proportions of oxides that can not be extracted by ammonia extraction are different for MoO3, NiO and ZnO which are supported on rutile TiO2.     

金红石/锐钛矿混晶结构的TiO2薄膜光催化活性

采用磁控溅射法制备出一组金红石/锐钛矿混晶结构的纳米TiO2薄膜催化剂,并通过光催化降解苯酚实验考察该薄膜的催化性能. 光催化实验证明, 随着催化剂中金红石含量减少, 催化剂的光催化活性逐渐提高. X射线衍射(XRD)、X射线光电子能谱(XPS)、表面光电压谱(SPS)和原子力显微镜(AFM)结果表明, 催化剂为金红石和锐钛矿混晶结构, 并随着金红石含量减少, 催化剂的表面羟基(OH)和桥氧(—O—)的含量逐渐增加, 而且费米能级逐渐提高. 表面羟基和桥氧是有利于光催化的“活性物种”; 费米能级的提高使TiO2/H2O 面处TiO2的表面带弯增大, 导致了价带光生空穴参加光催化反应的几率增大, 有效地促进了光生载流子的分离; 这些因素是催化剂光催化活性逐渐提高的主要原因.     

负载型三氧化钼催化剂表面结构和表面酸位的激光Raman光谱研究

测定了MoO3/γ-Al2O3、MoO3/TiO2、MoO3/SiO2的激光Raman谱. 通过MoO3/γ-Al2O3、MoO3/TiO2在吡啶吸附前后、氨水提取前后的谱图对比说明, 单层分散的MoO3, 即特征峰为～950cm^-^1的"二维聚钼酸"中钼的配位状态不是单一的,其中一种表面含钼物种(Mo-1)不吸附吡啶, 不溶于氨水, 不显示较强的表面酸性; 另一种表面含钼物种(Mo-2)可吸附吡啶, 溶于氨水, 与催化剂的表面酸位密切相关. 我们认为Mo-1为四面体配位的钼; Mo-2为八面体配位的钼. MoO3/SiO2中的MoO3能100%被氨水溶去, 其酸位数与表面Mo^6^+数之比接近1, 是由其中Mo-2的比例较高, 载体与活性组分之间的相互作用较弱这两个因素所造成的。     

甲烷无氧脱氢芳构化催化剂Mo/HZSM-5的研究

催化剂Ｍｏ／ＨＺＳＭ－５在甲烷地氧脱氢芳构化反应中表现出很高的活性，用ＸＲＤ，ＢＥＴ经表面，ＮＨ３－ＴＰＤ及ＴＰＲ等手段，对不抽提前后催化剂上的活性ｏ的种进行了研究，ＸＲＤ结果表明，Ｍｏ物种高度分散于筛表面，随着Ｍｏ担载量的提高，ＢＥＴ比表面积有所下降；但氨水抽提后，比表面积有很大程度的恢复，ＮＨ３－ＴＰＤ结果表明，Ｍｏ物种优先占据分子筛中的强酸位。ＴＰＲ结果显示出有ＭｏＯ３晶相存在的催化剂较易被     

The adsorption and reaction of a titanate coupling reagent on the surfaces of different nanoparticles in supercritical CO2

The adsorption and reaction in supercritical CO2 of the titanate coupling reagent NDZ-201 on the surfaces of seven metal oxide particles, SiO2, Al2O3, ZrO2, TiO2 (anatase), TiO2 (rutile), Fe2O3, and Fe3O4, was investigated. FTIR and TG analysis indicated that the adsorption and reaction were different on different particle surfaces. On SiO2 and Al2O3 particles, there was a chemical reaction of the titanate coupling reagent on the surfaces. On the surfaces of ZrO2 and TiO2 (anatase) particles, there were two kinds of adsorption, weak and strong adsorption. On the surfaces of TiO2 (rutile), Fe2O3, and Fe3O4 particles, there was only weak adsorption. The acidity or basicity of the OH groups on the particle surface was the key factor that determined if a surface reaction occurred. When the OH groups were acidic, the titanate coupling reagent reacted with these, but otherwise, there was no reaction. The surface density of OH groups on the original particles and the amount of titanate coupling reagent adsorbed and reacted were estimated from TG analysis. The reactivity of the surface OH groups of Al2O3 particles was higher than that of the SiO2 particles.     

TiO2纳米晶光催化降解铬酸根离子的研究

以二氧化钛为光催化剂,研究了溶液的ｐＨ值、铬酸根离子的初始浓度、通入的气体种类、氧化钛的载量等因素对铬酸根离子降解率的影响。同时合成了粒径小于１０ｎｍ的锐钛矿相和金红石相氧化钛纳米晶来考察晶相和尺寸效应对降解率的影响。结果表明,锐钛矿的催化活性高于金红石相,两者的催化活性均大大高于市售的氧化钛微粉。     

A comparative study on the dispersion behaviors and surface acid properties of molybdena on CeO2 and ZrO2 (Tet)

Dispersion of molybdena on CeO₂, ZrO₂ (Tet), and a mixture of CeO₂ and ZrO₂ (Tet), was investigated by using laser Raman spectroscopy (LRS), Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD) and temperature programmed reduction (TPR). The results indicate that molybdena is dispersed on both individual oxide support and mixed oxide support at the adopted molybdena loadings (0.2 and 0.8 mmol Mo⁶⁺/100 m²) and the structure of the supported molybdena species is intimate association with its loading amount. Two molybdena species are identified by Raman results, i.e. isolated MoO²⁻₄ species at 0.2 mmol Mo⁶⁺/100 m² and polymolybdate species at 0.8 mmol Mo⁶⁺/100 m². IR spectra of ammonia adsorption prove that isolated MoO²⁻₄ species are Lewis acid sites on the Mo/Ce and/or Zr samples, and the polymolybdate species are Brönsted acid sites on the Mo/Ce and/or Zr samples. Moreover, a combination of the Raman, IR and TPR results confirms that at 0.2 mmol Mo⁶⁺/100 m² Ce + Zr, molybdena is preferentially dispersed on the surface of CeO₂ when a mixed oxide support (CeO₂ and ZrO₂) is present, which was explained in term of the difference of the surface basicity between CeO₂ and ZrO₂ (Tet). Surface structures of the oxide supports were also taken into consideration.     

负载金属对MoO3-TiO2光催化剂结构与催化性能的影响

用溶胶-凝胶和浸渍-还原相结合的方法制得M/MoO3-TiO2 (M=Pd, Cu, Ni和Ag)光催化剂。利用X-射线衍射(XRD)、程序升温还原(TPR)、红外光谱(IR)、程序升温脱附(TPD)、紫外-可见漫反射光谱(UV-VisDRS)和光反应等技术,研究了负载金属复合半导体的物相结构、吸附性能、吸光性能和光催化反应性能。结果表明,金属M(M=Pd, Cu)负载在复合半导体上,延迟了TiO2由锐钛矿向金红石相的转化,增强了Mo与载体TiO2的相互作用,促进Mo物种由四面体配位向八面体配位转化,使TiO2光吸收限发生蓝移,对可见光部分的吸收明显增加,拓宽了催化剂的光响应范围;固体材料吸光性能强弱顺序Pd/MoO3-TiO2 >Cu/MoO3-TiO2>Ag/MoO3-TiO2>Ni/MoO3-TiO2;Pd对CO2吸附能力过强,卧式吸附态脱附温度高,光催化效率不高;金属Cu对CO2吸附能力适中,CO2与C3H6脱附温度较接近,实现了光-表面-热的协同作用,光量子效率最高。     

Effect of TiO2 crystalline phase composition on the physicochemical and catalytic properties of Pd/TiO(2) in selective acetylene hydrogenation

Pd/TiO(2) catalysts have been prepared using TiO(2) supports consisting of various rutile/anatase crystalline phase compositions. Increasing percentages of rutile phase in the TiO(2) resulted in a decrease in Brunauer-Emmett-Teller surface areas, fewer Ti(3+) sites, and lower Pd dispersion. While acetylene conversions were found to be merely dependent on Pd dispersion, ethylene selectivity appeared to be strongly affected by the presence of Ti(3+) in the TiO(2) samples. When TiO(2) samples with 0-44% rutile were used, high ethylene selectivities (58-93%) were obtained whereas ethylene losses occurred for those supported on TiO(2) with 85% or 100% rutile phase. X-ray photoelectron spectroscopy and electron spin resonance experiments revealed that a significant amount of Ti(3+) existed in the TiO(2) samples composed of 0-44% rutile. The presence of Ti(3+) in contact with Pd can probably lower the adsorption strength of ethylene resulting in an ethylene gain. Among the five catalysts used in this study, the results for Pd/TiO(2)-R44 suggest an optimum anatase/rutile composition of the TiO(2) used to obtain high selectivity of ethylene in selective acetylene hydrogenation.     

纳米TiO2的制备及对三甲胺气体的敏感性能

用硬脂酸凝胶法制备纳米TiO₂材料,并用XRD、TEM、IR对纳米晶的晶型、晶粒大小及形貌进行表征；用XPS分析不同晶型的纳米TiO₂表面吸附氧的情况，发现锐钛矿型纳米TiO₂比金红石型纳米TiO₂有较多的表面吸附氧. 检测了不同晶型纳米TiO₂对三甲胺（TMA）气体的敏感性能.结果表明锐钛矿型纳米TiO₂对TMA有较高的灵敏度. 对敏感性能的机理进行了讨论.     

WO3改性方法对MnOx/TiO2催化剂低温催化NH3还原NO特性的影响（英文）

采用3种不同的浸渍过程制备了系列WO3改性MnOx/TiO2催化剂,并采用BET比表面积测试、X射线衍射、拉曼光谱、H2程序升温还原、高分辨扫描电镜和原位红外光谱等技术进行表征.结果显示,一步浸渍法和先钨后锰的分布浸渍法制备的催化剂中,Mn和W的协同作用提高了活性组分的分散状态,并阻止了钛载体的转晶;在所有的Mn基催化剂中,Mn物种主要以Mn2O3形式存在,但在15%MnOx-5%WO3/TiO2中出现了少量的MnO2;WO3的加入大大增强了催化剂的还原能力,提高了其表面酸位尤其是B酸的数量与强度,并促进了活性中间物(NH2)的生成.表面Lewis酸在低温SCR反应起主要作用,并且发现NH2也是活性很高的物种.在NH3低温催化还原NO的反应中,一步浸渍法制备的催化剂活性最高.     

Quantitative characterization of hydroxyl radicals produced by various photocatalysts

Hydroxyl radicals ((·)OH) have been deemed to be the major active species during the photocatalytic oxidation reaction. In this study, (·)OH produced on various semiconductor photocatalysts in aqueous solution under Xenon lamp irradiation was quantitatively investigated by the photoluminescence (PL) technique using coumarin (COU) as a probe molecule. The results indicated that the formation rate of (·)OH on the surface of irradiated commercial Degussa P25 (P25) was much higher than that of other semiconductor. The pH values of the solution and phase structure of TiO(2) significantly influenced the production rate of (·)OH. The acidic pH environment of the solutions and bi-phase structure (anatase and rutile) of TiO(2) were beneficial to enhancing the formation rate of (·)OH. In addition, the formation rate of (·)OH on anatase TiO(2) and P25 was much faster than that of (·)OH on the other semiconductors (such as rutile TiO(2), ZnO, WO(3), CdS, Bi(2)WO(4) and BiOCl, etc.). A new concept "OH-index" was first proposed to compare photocatalytic activity of photocatalysts, which would provide new insight into the investigation of semiconductor photocatalysts.     

UV Raman spectroscopic study on TiO2. I. Phase transformation at the surface and in the bulk

Phase transformation of TiO2 from anatase to rutile is studied by UV Raman spectroscopy excited by 325 and 244 nm lasers, visible Raman spectroscopy excited by 532 nm laser, X-ray diffraction (XRD), and transmission electron microscopy (TEM). UV Raman spectroscopy is found to be more sensitive to the surface region of TiO2 than visible Raman spectroscopy and XRD because TiO2 strongly absorbs UV light. The anatase phase is detected by UV Raman spectroscopy for the sample calcined at higher temperatures than when it is detected by visible Raman spectroscopy and XRD. The inconsistency in the results from the above three techniques suggests that the anatase phase of TiO2 at the surface region can remain at relatively higher calcination temperatures than that in the bulk during the phase transformation. The TEM results show that small particles agglomerate into big particles when the TiO2 sample is calcined at elevated temperatures and the agglomeration of the TiO2 particles is along with the phase transformation from anatase to rutile. It is suggested that the rutile phase starts to form at the interfaces between the anatase particles in the agglomerated TiO2 particles; namely, the anatase phase in the inner region of the agglomerated TiO2 particles turns out to change into the rutile phase more easily than that in the outer surface region of the agglomerated TiO2 particles. When the anatase particles of TiO2 are covered with highly dispersed La2O3, the phase transformation in both the bulk and surface regions is significantly retarded, owing to avoiding direct contact of the anatase particles and occupying the surface defect sites of the anatase particles by La2O3.     

NiO在γ-Al_2O_3及 TiO_2/γ-Al_2O_3载体上的表面存在状态

本文采用 LRS, XRD, UV-DRS, TPR考查了γ-Al2O3上 TiO2的分散容量,分散态 Ti4＋离子的配位环境; NiO在经 TiO2改性后的γ-Al2O3载体上的分散容量。结果表明：（ 1） TiO2在γ-Al2O3表面的分散容量约为 0.62 mmol/100m2γ-Al2O3,当 TiO2含量低于该分散容量时 Ti4＋在γ-Al2O3载体表面以嵌入形式呈离子态分布;而含量高于分散容量时还有结晶态的 TiO2出现。（ 2） NiO在 TiO2/γ-Al2O3载体表面的分散容量约为 1.1 mmol/100m2γ-Al2O3,比之在γ-Al2O3载体表面的分散容量 (1.5mmol/100m2γ-Al2O3)要低,这是由于γ-Al2O3表面上部分空位被 Ti4＋离子占据。用表面相互作用的“嵌入模型” (Incorporation Model）讨论了这些结果。     

Photodeposition of Prussian Blue Films on TiO(2): Additive Effect of Methanol and Influence of the TiO(2) Crystal Form

The coupling of TiO(2) and transition metal complexes is attempted with the aim of higher functionalization of the TiO(2) photocatalyst. UV irradiation (lambda(ex)>300 nm) of a TiO(2) suspension containing equimolar aqueous solutions of FeCl(3) and K(3)[Fe(CN)(6)] forms uniform thin films of "water-insoluble Prussian blue" (PB, Fe(4)(3+) [Fe(II)(CN)(6)](3)) on the surface of TiO(2) particles. The PB photodeposition is enhanced significantly by the addition of a small amount of CH(3)OH in both the rutile and anatase TiO(2) systems. The activity of anatase TiO(2) is greater than that of rutile in the presence of CH(3)OH (2.46 M) by a factor of 1.6+/-0.2, whereas the activities are comparable in the absence of CH(3)OH. These results are discussed on the basis of a proposed reaction mechanism. Copyright 2001 Academic Press.     

Mo-Co系加氢精制催化剂中TiO~2-Al~2O~3载体效应的PASCA研究

本文采用PASCA(化学分析正电子湮没谱)技术, 系统地研究了MoO~3/γ-Al~2O~3,CoO/γ-Al~2O~3, MoO~3/TiO~2-Al~2O~3, CoO/TiO~2-Al~2O~3等体系中活性组分的表面分散状态和化学状态及其变化规律, 揭示了用TiO~2改性Al~2O~3对Mo-Co系加氢精制催化剂所产生的载体效应的作用机理。Al~2O~3中引入TiO~2使得载体与MoO~3间的相互作用大大减弱, 导致分散态MoO~3易于还原和硫化。助剂CoO与TiO~2-Al~2O~3载体间存在极为显著的电子相互作用, 对于改善Co在活性相中的化学状态, 提高活性中心的内在活性具有重要的作用。PASCA研究的另一个重要结果是, 由于载体表面的不均匀性,使得上述负载型催化剂中氧化物活性组分的表面状态十分复杂, 存在与载体相互作用强弱程度不同的多类特征区, 这些特征区与内在活性不同的催化中心相关联. 通过TiO~2改性Al~2O~3载体, 有效地调节载体表面性质, 改变活性组分表面物种的分布及化学状态。