Surface Reorganization on Electrochemically‐Induced Zn–Ni–Co Spinel Oxides for Enhanced Oxygen Electrocatalysis

Herein, we highlight redox‐inert Zn²⁺ in spinel‐type oxide (Zn_XNi_1?XCo₂O₄) to synergistically optimize physical pore structure and increase the formation of active species on the catalyst surface. The presence of Zn²⁺ segregation has been identified experimentally and theoretically under oxygen‐evolving condition, the newly formed V_Zn?O?Co allows more suitable binding interaction between the active center Co and the oxygenated species, resulting in superior ORR performance. Moreover, a liquid flow Zn–air battery is constituted employing the structurally optimized Zn_0.4Ni_0.6Co₂O₄ nanoparticles supported on N‐doped carbon nanotube (ZNCO/NCNTs) as an efficient air cathode, which presents remarkable power density (109.1 mW cm^?2), high open circuit potential (1.48 V vs. Zn), excellent durability, and high‐rate performance. This finding could elucidate the experimentally observed enhancement in the ORR activity of Zn_XNi_1?XCo₂O₄ oxides after the OER test.     

A Phthalocyanine‐Based Layered Two‐Dimensional Conjugated Metal–Organic Framework as a Highly Efficient Electrocatalyst for the Oxygen Reduction Reaction

Layered two‐dimensional (2D) conjugated metal–organic frameworks (MOFs) represent a family of rising electrocatalysts for the oxygen reduction reaction (ORR), due to the controllable architectures, excellent electrical conductivity, and highly exposed well‐defined molecular active sites. Herein, we report a copper phthalocyanine based 2D conjugated MOF with square‐planar cobalt bis(dihydroxy) complexes (Co‐O₄) as linkages (PcCu‐O₈‐Co) and layer‐stacked structures prepared via solvothermal synthesis. PcCu‐O₈‐Co 2D MOF mixed with carbon nanotubes exhibits excellent electrocatalytic ORR activity (E_1/2=0.83 V vs. RHE, n=3.93, and j_L=5.3 mA cm^?2) in alkaline media, which is the record value among the reported intrinsic MOF electrocatalysts. Supported by in situ Raman spectro‐electrochemistry and theoretical modeling as well as contrast catalytic tests, we identified the cobalt nodes as ORR active sites. Furthermore, when employed as a cathode electrocatalyst for zinc–air batteries, PcCu‐O₈‐Co delivers a maximum power density of 94 mW cm^?2, outperforming the state‐of‐the‐art Pt/C electrocatalysts (78.3 mW cm^?2).     

Cu/Cu_2O nanoparticles co-regulated carbon catalyst for alkaline Al-air batteries

Developing high-efficiency,inexpensive,and steady non-precious metal oxygen reduction reaction(ORR) catalysts to displace Pt-based catalysts is significant for commercial applications of Al-air battery.Here,we have prepared the Cu/Cu_2 O-NC catalyst with excellent ORR performance and high stability,due to the synergistic effect of Cu and Cu_2 O nanoparticles.The half-wave potential(0.8 V) and the limiting-current density(5.20 mA/cm~2) of the Cu/Cu_2 O-NC are very close to those of the 20% Pt/C catalyst(0.82 V,5.10 mA/cm~2).Besides,it exhibits excellent performance with a maximal power density of 250 mW/cm~2 and a stable continuous discharge for more than 90 h in the Al-air battery test The promoting effects of Cu_2 O towards Cu-based ORR catalysts are illustrated as follows:(ⅰ) Cu_2 O is the major ORR active site by the redox of Cu(Ⅱ)/Cu(Ⅰ),which provides excellent ORR activities;(ⅱ) Cu can stabilize the location of Cu_2 O by assisting the electron transfer to Cu(Ⅱ)/Cu(Ⅰ) redox,which is conducive to the high stability of the catalyst.This work provides a useful strategy for enhancing the ORR performance of Cu-based catalysts.     

Surface Reorganization on Electrochemically-Induced Zn–Ni–Co Spinel Oxides for Enhanced Oxygen Electrocatalysis

Herein, we highlight redox-inert Zn²⁺ in spinel-type oxide (Zn_XNi_1−XCo₂O₄) to synergistically optimize physical pore structure and increase the formation of active species on the catalyst surface. The presence of Zn²⁺ segregation has been identified experimentally and theoretically under oxygen-evolving condition, the newly formed V_Zn−O−Co allows more suitable binding interaction between the active center Co and the oxygenated species, resulting in superior ORR performance. Moreover, a liquid flow Zn–air battery is constituted employing the structurally optimized Zn_0.4Ni_0.6Co₂O₄ nanoparticles supported on N-doped carbon nanotube (ZNCO/NCNTs) as an efficient air cathode, which presents remarkable power density (109.1 mW cm⁻²), high open circuit potential (1.48 V vs. Zn), excellent durability, and high-rate performance. This finding could elucidate the experimentally observed enhancement in the ORR activity of Zn_XNi_1−XCo₂O₄ oxides after the OER test.     

Molecular Engineering of a 3D Self‐Supported Electrode for Oxygen Electrocatalysis in Neutral Media

Electrodes for oxygen evolution reaction (OER) and oxygen reduction reaction (ORR) are required in energy conversion and storage technologies. An assembly strategy involves covalently grafting Co corrole 1 onto Fe₃O₄ nanoarrays grown on Ti mesh. The resulted electrode shows significantly improved activity and durability for OER and ORR in neutral media as compared to Fe₃O₄ alone and with directly adsorbed 1 . It also displays higher atom efficiency (at least two magnitudes larger turnover frequency) than reported electrodes. Using this electrode in a neutral Zn‐air battery, a small charge–discharge voltage gap of 1.19 V, large peak power density of 90.4 mW cm^?2, and high rechargeable stability for >100 h are achieved, opening a promising avenue of molecular electrocatalysis in a metal–air battery. This work shows a molecule‐engineered electrode for electrocatalysis and demonstrates their potential applications in energy conversion and storage.     

Graphitic C<Subscript>3</Subscript>N<Subscript>4</Subscript>@MWCNTs supported Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> as a novel electrocatalyst for the oxygen reduction reaction in zinc–air batteries

A series of catalysts (g-C₃N₄@MWCNTs/Mn₃O₄) were prepared from g-C₃N₄, MWCNTs, and Mn₃O₄ for oxygen reduction reaction (ORR) in zinc–air batteries. From the half-cell tests, the loading of 35 % Mn₃O₄ (sample GMM35) presents an excellent activity toward ORR in alkaline condition. Rotating ring-disk electrode (RRDE) studies reveal that 3.6～3.8 electrons are transferred with a H₂O₂ yield of 11.4 % at ?0.4 V. Meanwhile, the GMM35 nanocomposite exhibits the same durability as commercial 20 wt% Pt/C in alkaline condition, but it shows lower peak power density (192.4 mW cm^?2 at 229.1 mA cm^?2) and cell voltage than those with a commercial Pt/C catalyst (260.9 mW cm^?2 at 285.4 mA cm^?2).     

Alkaline–Acid Zn–H2O Fuel Cell for the Simultaneous Generation of Hydrogen and Electricity

An alkaline–acid Zn–H₂O fuel cell is proposed for the simultaneous generation of electricity with an open circuit voltage of about 1.25 V and production of H₂ with almost 100 % Faradic efficiency. We demonstrate that, as a result of harvesting energy from both electrochemical neutralization and electrochemical Zn oxidation, the as‐developed hybrid cell can deliver a power density of up to 80 mW cm^?2 and an energy density of 934 Wh kg^?1 and maintain long‐term stability for H₂ production with an output voltage of 1.16 V at a current density of 10 mA cm^?2.     

Carbon‐Supported Divacancy‐Anchored Platinum Single‐Atom Electrocatalysts with Superhigh Pt Utilization for the Oxygen Reduction Reaction

Maximizing the platinum utilization in electrocatalysts toward oxygen reduction reaction (ORR) is very desirable for large‐scale sustainable application of Pt in energy systems. A cost‐effective carbon‐supported carbon‐defect‐anchored platinum single‐atom electrocatalysts (Pt₁/C) with remarkable ORR performance is reported. An acidic H₂/O₂ single cell with Pt₁/C as cathode delivers a maximum power density of 520 mW cm^?2 at 80 °C, corresponding to a superhigh platinum utilization of 0.09 g_Pt kW^?1. Further physical characterization and density functional theory computations reveal that single Pt atoms anchored stably by four carbon atoms in carbon divacancies (Pt‐C₄) are the main active centers for the observed high ORR performance.     

S‐Doping of an Fe/N/C ORR Catalyst for Polymer Electrolyte Membrane Fuel Cells with High Power Density

Fe/N/C is a promising non‐Pt electrocatalyst for the oxygen reduction reaction (ORR), but its catalytic activity is considerably inferior to that of Pt in acidic medium, the environment of polymer electrolyte membrane fuel cells (PEMFCs). An improved Fe/N/C catalyst (denoted as Fe/N/C‐SCN) derived from Fe(SCN)₃, poly‐m‐phenylenediamine, and carbon black is presented. The advantage of using Fe(SCN)₃ as iron source is that the obtained catalyst has a high level of S doping and high surface area, and thus exhibits excellent ORR activity (23 A g^?1 at 0.80 V) in 0.1 M H₂SO₄ solution. When the Fe/N/C‐SCN was applied in a PEMFC as cathode catalyst, the maximal power density could exceed 1 W cm^?2.     

Nitrogen‐doped Carbon–CoOx Nanohybrids: A Precious Metal Free Cathode that Exceeds 1.0 W cm−2 Peak Power and 100 h Life in Anion‐Exchange Membrane Fuel Cells

Efficient and durable nonprecious metal electrocatalysts for the oxygen reduction (ORR) are highly desirable for several electrochemical devices, including anion exchange membrane fuel cells (AEMFCs). Here, a 2D planar electrocatalyst with CoO_x embedded in nitrogen‐doped graphitic carbon (N‐C‐CoO_x) was created through the direct pyrolysis of a metal–organic complex with a NaCl template. The N‐C‐CoO_x catalyst showed high ORR activity, indicated by excellent half‐wave (0.84 V vs. RHE) and onset (1.01 V vs. RHE) potentials. This high intrinsic activity was also observed in operating AEMFCs where the kinetic current was 100 mA cm^?2 at 0.85 V. When paired with a radiation‐grafted ETFE powder ionomer, the N‐C‐CoO_x AEMFC cathode was able to achieve extremely high peak power density (1.05 W cm^?2) and mass transport limited current (3 A cm^?2) for a precious metal free electrode. The N‐C‐CoO_x cathode also showed good stability over 100 hours of operation with a voltage decay of only 15 % at 600 mA cm^?2 under H₂/air (CO₂‐free) reacting gas feeds. The N‐C‐CoO_x cathode catalyst was also paired with a very low loading PtRu/C anode catalyst, to create AEMFCs with a total PGM loading of only 0.10 mg_Pt‐Ru cm^?2 capable of achieving 7.4 W mg^?1_PGM as well as supporting a current of 0.7 A cm^?2 at 0.6 V with H₂/air (CO₂ free)—creating a cell that was able to meet the 2019 U.S. Department of Energy initial performance target of 0.6 V at 0.6 A cm^?2 under H₂/air with a PGM loading <0.125 mg cm^?2 with AEMFCs for the first time.     

A Hybrid Co Quaterpyridine Complex/Carbon Nanotube Catalytic Material for CO2 Reduction in Water

Associating a metal‐based catalyst to a carbon‐based nanomaterial is a promising approach for the production of solar fuels from CO₂. Upon appending a Co^II quaterpyridine complex [Co(qpy)]²⁺ at the surface of multi‐walled carbon nanotubes, CO₂ conversion into CO was realized in water at pH 7.3 with 100 % catalytic selectivity and 100 % Faradaic efficiency, at low catalyst loading and reduced overpotential. A current density of 0.94 mA cm^?2 was reached at ?0.35 V vs. RHE (240 mV overpotential), and 9.3 mA cm^?2 could be sustained for hours at only 340 mV overpotential with excellent catalyst stability (89 095 catalytic cycles in 4.5 h), while 19.9 mA cm^?2 was met at 440 mV overpotential. Such a hybrid material combines the high selectivity of a homogeneous molecular catalyst to the robustness of a heterogeneous material. Catalytic performances compare well with those of noble‐metal‐based nano‐electrocatalysts and atomically dispersed metal atoms in carbon matrices.     

Dual‐Template Pore Engineering of Whey Powder‐Derived Carbon as an Efficient Oxygen Reduction Reaction Electrocatalyst for Primary Zinc‐Air Battery

Cost‐effective and high‐performance electrocatalysts for oxygen reduction reactions (ORR) are needed for many energy storage and conversion devices. Here, we demonstrate that whey powder, a major by‐product in the dairy industry, can be used as a sustainable precursor to produce heteroatom doped carbon electrocatalysts for ORR. Rich N and S compounds in whey powders can generate abundant catalytic active sites. However, these sites are not easily accessible by reactants of ORR. A dual‐template method was used to create a hierarchically and interconnected porous structure with micropores created by ZnCl₂ and large mesopores generated by fumed SiO₂ particles. At the optimum mass ratio of whey power: ZnCl₂ : SiO₂ at 1 : 3 : 0.8, the resulting carbon material has a large specific surface area close to 2000 m² g^?1, containing 4.6 at.% of N with 39.7% as pyridinic N. This carbon material shows superior electrocatalytic activity for ORR, with an electron transfer number of 3.88 and a large kinetic limiting current density of 45.40 mA cm^?2. They were employed as ORR catalysts to assemble primary zinc‐air batteries, which deliver a power density of 84.1 mW cm^?2 and a specific capacity of 779.5 mAh g^?1, outperforming batteries constructed using a commercial Pt/C catalyst. Our findings open new opportunities to use an abundant biomaterial, whey powder, to create high‐value‐added carbon electrocatalysts for emerging energy applications.     

Heterostructured Inter‐Doped Ruthenium–Cobalt Oxide Hollow Nanosheet Arrays for Highly Efficient Overall Water Splitting

The development of transition‐metal‐oxides (TMOs)‐based bifunctional catalysts toward efficient overall water splitting through delicate control of composition and structure is a challenging task. Herein, the rational design and controllable fabrication of unique heterostructured inter‐doped ruthenium–cobalt oxide [(Ru–Co)O_x] hollow nanosheet arrays on carbon cloth is reported. Benefiting from the desirable compositional and structural advantages of more exposed active sites, optimized electronic structure, and interfacial synergy effect, the (Ru–Co)O_x nanoarrays exhibited outstanding performance as a bifunctional catalyst. Particularly, the catalyst showed a remarkable hydrogen evolution reaction (HER) activity with an overpotential of 44.1 mV at 10 mA cm^?2 and a small Tafel slope of 23.5 mV dec^?1, as well as an excellent oxygen evolution reaction (OER) activity with an overpotential of 171.2 mV at 10 mA cm^?2. As a result, a very low cell voltage of 1.488 V was needed at 10 mA cm^?2 for alkaline overall water splitting.     

Synthesis of Non-precious N-doped Mesoporous Fe3O4/CoO@NC Materials towards Efficient Oxygen Reduction Reaction for Microbial Fuel Cells

N-doped transition metal oxides are strategic materials towards the efficient oxygen reduction reaction (ORR) of microbial fuel cells (MFCs). Non-precious N-doped Fe₃O₄/CoO@NC−T (T represents carbonization temperature) catalysts are prepared by an efficient two-step strategy for ORR. Fe₃O₄/CoO@NC-750 exhibits the best performance with an efficient four-electron transfer pathway. The optimal power density of MFCs by using Fe₃O₄/CoO@NC-750 as the cathode catalyst (1243.4 mW ⋅ m⁻²) is superior to that of the MFCs with commercial Pt/C catalyst (1080 mW ⋅ m⁻²), which shows an outstanding activity towards ORR. No significant decrease in output voltage results over 70 days, which shows an excellent electrochemical stability.     

Axial Ligand Coordination Tuning of the Electrocatalytic Activity of Iron Porphyrin Electrografted onto Carbon Nanotubes for the Oxygen Reduction Reaction

The oxygen reduction reaction (ORR) is essential in many life processes and energy conversion systems. It is desirable to design transition metal molecular catalysts inspired by enzymatic oxygen activation/reduction processes as an alternative to noble-metal-Pt-based ORR electrocatalysts, especially in view point of fuel cell commercialization. We have fabricated bio-inspired molecular catalysts electrografted onto multiwalled carbon nanotubes (MWCNTs) in which 5,10,15,20-tetra(pentafluorophenyl) iron porphyrin (iron porphyrin FeF₂₀TPP) is coordinated with covalently electrografted axial ligands varying from thiophene to imidazole on the MWCNTs’ surface. The catalysts’ electrocatalytic activity varied with the axial coordination environment (i. e., S-thiophene, N-imidazole, and O-carboxylate); the imidazole-coordinated catalyst MWCNTs-Im-FeF₂₀TPP exhibited the highest ORR activity among the prepared catalysts. When MWCNT-Im-FeF₂₀TPP was loaded onto the cathode of a zinc−air battery, an open-cell voltage (OCV) of 1.35 V and a maximum power density (P_max) of 110 mW cm⁻² were achieved; this was higher than those of MWCNTs-Thi-FeF₂₀TPP (OCV=1.30 V, P_max=100 mW cm⁻²) and MWCNTs-Ox-FeF₂₀TPP (OCV=1.28 V, P_max=86 mW cm⁻²) and comparable with a commercial Pt/C catalyst (OCV=1.45 V, P_max=120 mW cm⁻²) under similar experimental conditions. This study provides a time-saving method to prepare covalently immobilized molecular electrocatalysts on carbon-based materials with structure–performance correlation that is also applicable to the design of other electrografted catalysts for energy conversion.     

Accelerating the oxygen reduction reaction via a bioinspired carbon‐supported zinc electrocatalyst

Oxygen utilization in electrochemical energy generation systems requires to overcome the slow kinetics of oxygen reduction reaction (ORR). Herein, we have outstretched an efficient strategy in order for developing a bioinspired Zn (N₄)/sulfur/graphitic carbon composite (Zn‐S‐Gc) with an effective performance for the ORR at low temperature. The catalyst composite was created by attaching the Zn (N₄) centers in the form of zinc phthalocyanine on the sulfur‐linked graphitic carbon surface. The most positive ORR onset potential of about 1.00 V versus a reversible hydrogen electrode (RHE) was obtained due to the unique structure of a new catalyst in KOH solution (pH = 13) at low temperature (T = 298 K). The catalyst was evaluated using the rotating‐disk electrode method in the potential range of ?0.02–1.18 V versus RHE. The number of transferred electrons as one of the most important parameters (n > 3.70) is almost constant in a wide range of low overpotentials (0.1–0.6 V), which indicates a more efficient four‐electron pathway from O₂ to H₂O on the catalyst surface. The estimated Tafel slope in an appropriate range is about ≈ ?133.3 mV/dec at a low current density and E_1/2 of the electrocatalyst displays a negative shift of only 11 mV after 10,000 cycles. The mean size of the catalyst centers is on the nanoscale (<50 nm).     

Synergistic Enhancement of Electrocatalytic Activity toward Oxygen Reduction Reaction in Alkaline Electrolytes with Pentabasic (Fe,B, N,S, P)‐Doped Reduced Graphene Oxide

As alternatives to Pt‐based electrocatalysts, the development of nonprecious metal catalysts with high performance in the cathodic oxygen reduction reaction (ORR) is highly desirable for widespread use in fuel cells. Here we report a simple approach for preparing pentabasic (Fe, B, N, S, P)‐doped reduced graphene oxide (rGO) via a two‐step doping method of adding boric acid and ferric chloride to ternary (N, S, P)‐doped rGO (NSPG). Electrochemical investigation of the composites for the ORR revealed that simultaneously doping appropriate amounts of Fe and B into the NSPG produced a synergistic effect that endowed the prepared catalyst with both a positively shifted ORR half‐wave potential and high selectivity for the 4e^? reduction of O₂. The optimized Fe₂B‐NSPG catalyst approached a 4e^? process for the ORR with a half‐wave potential (E_1/2=0.90 V vs. RHE) even 30 mV higher than that of the commercial Pt/C catalyst in alkaline solution. Furthermore, relative to the Pt/C catalyst, the Fe₂B‐NSPG demonstrated superior stability and excellent tolerance of the methanol cross‐over effect. This simple method afforded pentabasic (Fe, B, N, S, P)‐doped rGO as a promising nonprecious metal catalyst used for alkaline fuel cells.     

Sulfur‐Modified Oxygen Vacancies in Iron–Cobalt Oxide Nanosheets: Enabling Extremely High Activity of the Oxygen Evolution Reaction to Achieve the Industrial Water Splitting Benchmark

The oxygen vacancies of defective iron–cobalt oxide (FeCoO_x‐Vo) nanosheets are modified by the homogeneously distributed sulfur (S) atoms. S atoms can not only effectively stabilize oxygen vacancies (Vo), but also form the Co?S coordination with Co active site in the Vo, which can modulate the electronic structure of the active site, enabling FeCoO_x‐Vo‐S to exhibit much superior OER activity. FeCoO_x‐Vo‐S exhibits a mass activity of 2440.0 A g^?1 at 1.5 V vs. RHE in 1.0 m KOH, 25.4 times higher than that of RuO₂. The Tafel slope is as low as 21.0 mV dec^?1, indicative of its excellent charge transfer rate. When FeCoO_x‐Vo‐S (anode catalyst) is paired with the defective CoP₃/Ni₂P (cathode catalyst) for overall water splitting, current densities of as high as 249.0 mA cm^?2 and 406.0 mA cm^?2 at a cell voltage of 2.0 V and 2.3 V, respectively, can be achieved.     

Polymer-Assisted Electrophoretic Synthesis of N-Doped Graphene-Polypyrrole Demonstrating Oxygen Reduction with Excellent Methanol Crossover Impact and Durability

The design and synthesis of metal-free catalysts with superior electrocatalytic activity, high durability, low cost, and under mild conditions is extremely desirable but remains challenging. To address this problem, a polymer-assisted electrochemical exfoliation technique of graphite in the presence of an aqueous acidic medium is reported. This simple, cost-effective, and mass-scale production approach could open the possibility for the synthesis of high-quality nitrogen-doped graphene–polypyrrole (NG-PPy). The NG-PPy catalyst displays an improved half wave potential (E_1/2=0.77 V) in alkaline medium compared with G-PPy (E_1/2=0.66 V). Most importantly, this catalyst demonstrates excellent stability with high methanol tolerance, and it outperforms the commercial Pt/C catalyst and other previously reported metal-free catalysts. The content of graphitic nitrogen atoms is the key factor for the enhancement of electrocatalytic activity towards oxygen reduction reactions (ORR). Interestingly, the NG-PPy catalyst can be used as a cathode material in a zinc–air battery, which demonstrates a higher peak power density (59 mW cm⁻²) than G-PPy (36.6 mW cm⁻²), highlighting the importance of the low-cost material synthesis approach towards the development of metal-free efficient ORR catalysts for fuel cell and metal–air battery applications. Remarkably, the polymer-assisted electrophoretic exfoliation of graphite with a high yield (≈88 wt %) of few-layer graphene flakes could pave the way towards the mass production of high-quality graphene for a variety of applications.     

Two‐Dimensional Co@N‐Carbon Nanocomposites Facilely Derived from Metal–Organic Framework Nanosheets for Efficient Bifunctional Electrocatalysis

Metal–organic frameworks (MOFs) and MOF‐derived nanomaterials have recently attracted great interest as highly efficient, non‐noble‐metal catalysts. In particular, two‐dimensional MOF nanosheet materials possess the advantages of both 2D layered nanomaterials and MOFs and are considered to be promising nanomaterials. Herein, we report a facile and scalable in situ hydrothermal synthesis of Co–hypoxanthine (HPA) MOF nanosheets, which were then directly carbonized to prepare uniform Co@N‐Carbon nanosheets for efficient bifunctional electrocatalytic hydrogen‐evolution reactions (HERs) and oxygen‐evolution reactions (OERs). The Co embedded in N‐doped carbon shows excellent and stable catalytic performance for bifunctional electrocatalytic OERs and HERs. For OERs, the overpotential of Co@N‐Carbon at 10 mA cm^?2 was 400 mV (vs. reversible hydrogen electrode, RHE). The current density of Co@N‐Carbon reached 100 mA cm^?2 at an overpotential of 560 mV, which showed much better performance than RuO₂; the largest current density of RuO₂ that could be reached was only 44 mA cm^?2. The Tafel slope of Co@N‐Carbon was 61 mV dec^?1, which is comparable to that of commercial RuO₂ (58 mV dec^?1). The excellent electrocatalytic properties can be attributed to the nanosheet structure and well‐dispersed carbon‐encapsulated Co, CoN nanoparticles, and N‐dopant sites, which provided high conductivity and a large number of accessible active sites. The results highlight the great potential of utilizing MOF nanosheet materials as promising templates for the preparation of 2D Co@N‐Carbon materials for electrocatalysis and will pave the way to the development of more efficient 2D nanomaterials for various catalytic applications.