Synthesis of propylene carbonate from carbon dioxide using trans‐dichlorotetrapyridineru‐ thenium(II) as catalyst

trans‐Dichlorotetrapyridineruthenium(II) [trans‐RuCl₂(py)₄] was synthesized and the structure was determined by single crystal X‐ray crystallography. Highly efficient formation of propylene carbonate (PC) from carbon dioxide and propylene oxide was achieved by using a catalyst system composed of trans‐RuCl₂(py)₄ and hexadecyl trimethyl ammonium bromide under mild conditions (4h, 80 °C, 3.0 MPa). PC was obtained in nearly 100% selectivity without the formation of a polymer. The catalyst could be recycled constantly many times without any significant loss of its catalytic activity. On the basis of the results, a mechanism for the reaction was proposed. Copyright © 2010 European Peptide Society and John Wiley & Sons, Ltd.     

A one‐step strategy for aliphatic poly(carbonate‐ester)s with high performance derived from CO2, propylene oxide and l‐lactide

To improve the performance of PPC, aliphatic poly(carbonate‐ester)s were prepared in one‐step strategy from the terpolymerization of CO₂, propylene oxide (PO), and l ‐lactide (L ‐LA) catalyzed by zinc glutarate. Consequently giving high‐molecular weight terpolymers (PPCLAs) in a very high yield (8450.8–9435.8 g mol^?1 of Zn). The resulting terpolymers PPCLAs were characterized by ¹H NMR, showing that PPCLAs had an almost alternating structure for the components of CO₂, PO, and L‐LA. The influence of molecular weight and L‐LA content on the properties of PPCLAs was also investigated. Differential scanning calorimetry and thermogravimetric analysis (measurements revealed that the glass transition temperature (T _g) and thermal decomposition temperature (T _d) of PPCLAs are all much higher than those of PPC and increased with increasing molecular weight and L‐LA content. Tensile tests showed that the high mechanical properties of PPCLAs are due to the introduction of L‐LA into the copolymerization of CO₂ and PO. Furthermore, PPCLA4 exhibits high degradability, and after 10 weeks, the weight loss increases up to 6.58%, which is significantly higher than that of PPC of 4.58%. Copyright © 2016 John Wiley & Sons, Ltd.     

New strategies for synthesis of amino-functionalized poly(propylene carbonate) over SalenCo(III)Cl catalyst

New strategies for synthesis of amino-functionalized poly(propylene carbonate) (PPC) were applied by terpolymerization of carbon dioxide, propylene oxide, with (a) N-(2,3-epoxypropyl)-2-phthalimide (Monomer A )/N-(2-oxiranylmethyl)-1 or (b) N-(2-oxiranylmethyl)-1,1-dimethylethyl ester (Monomer B ) over SalenCo^(III)Cl/PPNCl catalysts system, followed by the removal of the respective protecting groups. The SalenCo^(III)Cl presented high activity and yielded the terpolymer with high polycarbonate selectivity, carbonate linkage content, as well as high head-to-tail stereoregularity (>99%). In terpolymerization, the Monomer A contents in PPC-Pht were easily regulated up to 12.0 mol%. However, the protecting groups could not be completely removed because of the degradation of PPC-NH₂- A during the deprotection process. Meanwhile, when terpolymerization with Monomer B , PPC-butoxy carbonyl was obtained varied the Monomer B contents from 1.3 to 4.5 mol%, and could be transformed completely into the amino-functionalized PPC-NH₂- B without significant backbone degradation. The contact angles of the functionalized PPC-NH₂s prepared by two strategies showed the expected increase in hydrophilicity with the increasing content of amino entities.     

聚苯乙烯负载聚乙二醇在合成碳酸亚丙酯上的应用

用金属钾、金属钠以及氢氧化钠水溶液等方法制备聚苯乙烯负载聚乙二醇，结果表明，采用金属钾比金属钢具有更好的接枝效果，并能使反应在较低的温度下较快进行。在氢氧化钠溶液中添加少量相转移剂，如Bu4NBr，接枝效果也有所提高。以聚苯乙烯负载聚乙二醇和KI一起为催化剂，研究了溶剂、温度等因素对CO2与环氧丙烷合成碳酸亚丙酯催化活性的影响。结果表明，以甲醇为溶剂催化活性较高。研究还表明，聚苯乙烯负载聚乙二醇具有较好的热稳定性，可以在150℃下重复使用至少5次。     

High yield synthesis of biodegradable poly(propylene carbonate) from carbon dioxide and propylene oxide

A novel SalenCo^III (2,4‐dinitrophenoxy) (Salen = N,N'‐bis(3,5‐di‐tert‐butylsalicylidene)‐1,2‐cyclohexanediamino) and 1,10‐phenanthroline monohydrate catalyst system was designed and employed for the copolymerization of CO₂ and propylene oxide (PO). The perfectly alternating copolymerization of CO₂ and PO proceeds effectively under middle temperature and pressure to yield poly(propylene carbonate) with a high yield and a high number average molecular weight of polymer. The structure of polymer was characterized by the IR and NMR measurements. The perfectly alternating copolymer was confirmed. The MALDI‐TOF spectrum insinuates that the copolymerization of CO₂ and PO was initiated by H₂O. Copyright © 2016 John Wiley & Sons, Ltd.     

Facile synthesis and crosslinking reaction of trifunctional five‐membered cyclic carbonate and dithiocarbonate

The trifunctional five‐membered cyclic carbonate 2 and dithiocarbonate 3 were successfully synthesized by the reaction of trifunctional epoxide 1 with carbon dioxide and carbon disulfide, respectively. The crosslinking reactions of 2 with p‐xylylenediamine or hexamethylenediamine were carried out in dimethyl sulfoxide at 100 °C for 48 h to produce the corresponding crosslinked poly(hydroxyurethane)s quantitatively. The crosslinking reactions of 3 with both p‐xylylenediamine and hexamethylenediamine, followed by acetylation of thiol moiety, produced the corresponding crosslinked poly(thioester–thiourethane)s quantitatively. The obtained crosslinked poly(hydroxyurethane)s were thermally more stable than the analogous crosslinked poly(thioester–thiourethane)s, probably because of less thermal stability of thiourethane moiety than hydroxyurethane moiety. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5983–5989, 2004     

Crosslinkable poly(propylene carbonate): High‐yield synthesis and performance improvement

A crosslinking strategy was used to improve the thermal and mechanical performance of poly(propylene carbonate) (PPC): PPC bearing a small moiety of pendant C?C groups was synthesized by the terpolymerization of allyl glycidyl ether (AGE), propylene oxide (PO), and carbon dioxide (CO₂). Almost no yield loss was found in comparison with that of the PO and CO₂ copolymer when the concentration of AGE units in the terpolymer was less than 5 mol %. Once subjected to UV‐radiation crosslinking, the crosslinked PPC film showed an elastic modulus 1 order of magnitude higher than that of the uncrosslinked one. Moreover, crosslinked PPC showed hot‐set elongation at 65 °C of 17.2% and permanent deformation approaching 0, whereas they were 35.3 and 17.2% for uncrosslinked PPC, respectively. Therefore, the PPC application window was enlarged to a higher temperature zone by the crosslinking strategy. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5329–5336, 2006     

Synthesis of propylene carbonate and some dialkyl carbonates in the presence of bifunctional catalyst compositions

Poly(ethylene glycol)–potassium iodide complexes were found to have high catalytic activities in the esterification of propylene oxide and carbon dioxide under smooth experimental conditions. Furthermore, the complexes were combined with sodium methoxide to form bifunctional catalyst compositions sequentially for the above esterification, as well as the transesterification of the propylene carbonate formed in situ with some aliphatic alcohols, such as methanol, ethanol, propanol and butanol. It was found that the compositions were very effective, giving corresponding dialkyl carbonate, propylene carbonate and propylene glycol. It was noticed that the resulting dialkyl carbonate from n-butanol was diisobutyl carbonate, instead of di-n-butyl carbonate.     

Regio‐regular structure high molecular weight poly(propylene carbonate) by rare earth ternary catalyst and Lewis base cocatalyst

Lewis base modification strategy on rare earth ternary catalyst was disclosed to enhance nucleophilic ability of active center during copolymerization of carbon dioxide and propylene oxide (PO), poly(propylene carbonate) (PPC) with H‐T linkages over 83%, and number–average molecular weight (M_n) up to 100 kg/mol was synthesized at room temperature using Y(CCl₃OO)₃‐ZnEt₂‐glycerine catalyst and 1,10‐phenanthroline (PHEN) cocatalyst. Coordination of PHEN with active Zinc center enhanced the nucleophilic ability of the metal carbonate, which became more regio‐specific in attacking carbon in PO, leading to PPC with improved H‐T linkages. Moreover, the binding of PHEN to active Zinc center also raised the carbonate content of PPC to over 99%, whereas the PPC from common rare earth ternary catalyst was about 96%. Unlike the highly regio‐regular structure PPC but with relatively low molecular weight recently reported in the literature, our high molecular weight regio‐regular PPC did show significant improvement in thermal and mechanical performances. PPC with H‐T linkages up to 83.2% showed glass transition temperature (T_g) of 43.3 °C, while T_g of PPC with H‐T linkages of 69.7% was only 36.1 °C. When H‐T connectivity was raised from 69.7 to 83.2%, the modulus of PPC showed a 78% increase. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4451–4458, 2008     

Influence of the soft segment length on the properties of water‐cured poly(carbonate‐urethane‐urea)s

Poly(carbonate‐urethane‐urea)s (PCUU) based on oligocarbonate diols (M_n ≈ 2000) with different length of the hydrocarbon chain as soft segments were synthesized and investigated. Carbonate oligomerols were obtained in a two‐step method from dimethyl carbonate (DMC) and linear α,ω‐diols (1,4‐butanediol, 1,5‐pentanediol, 1,6‐hexanediol, 1,9‐nonanediol, 1,10‐dekanediol and 1,12‐dodecanediol). Oligo(trimethylene carbonate) diol was synthesized using ring‐opening polymerization of trimethylence carbonate. PCUUs were obtained by prepolymer method using isophorone diisocyanate (IPDI) and water as a chain extender. Changes in polymers properties with increase of methylene group number between carbonate linkages were investigated by differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), tensile strength and hardness measurements. The thermal stability was also analyzed by means of thermogravimetric analysis (TGA). Based on FTIR analysis influence of methylene groups number between carbonate linkages on phase separation and concentration of allophanate and biuret groups in the samples were investigated. The obtained poly(carbonate‐urethane‐urea)s exhibited very good mechanical properties. Tensile strength and elongation at break were 40 MPa and 400–600%, respectively, depending on the oligocarbonate used. Copyright © 2014 John Wiley & Sons, Ltd.     

Highly active bifunctional cobalt‐salen complexes for the synthesis of poly(ester‐block‐carbonate) copolymer via terpolymerization of carbon dioxide,propylene oxide,and norbornene anhydride isomer: Roles of anhydride conformation consideration

This article describes an efficient synthetic route of defined reactive polyester‐block‐polycarbonate copolymers, utilizing a bifunctional SalenCoNO₃ complex as catalyst for the single‐step terpolymerization of norbornene anhydride (NA), propylene oxide, and carbon dioxide. The geometric isomer of NA plays an important role in polymerization efficacy and the resulting polymer microstructure, including carbonate content, sequence isomer of polycarbonate moiety, and molecular weight. A hydroxyl‐functionalized polyester–polycarbonate block copolymer was synthesized by a thiol‐ene reaction. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 789–795     

Synthesis and characterization of novel poly(ester‐carbonate)s by copolymerization of trans‐4‐hydroxy‐L‐proline with cyclic carbonate

The melt ring‐opening/condensation reaction of trans‐4‐hydroxy‐N‐benzyloxycarbonyl‐L‐proline (N‐CBz‐Hpr) with cyclic carbonate [trimethylene carbonate (tri‐MC) or tetramethylene carbonate (tetra‐MC)] at a wide range of molar fractions in the feed produced new degradable poly(ester‐carbonate)s. The influence of reaction conditions such as polymerization time and temperature on the yield and inherent viscosity of the copolymers was investigated. The polymerizations were carried out in bulk at 140 °C with 1.5 wt % stannous octoate as a catalyst for 30 h. The poly(ester‐carbonate)s obtained were characterized by Fourier transform infrared spectroscopy, ¹H NMR, differential scanning calorimetry, gel permeation chromatography, and Ubbelohde viscometry. The copolymers synthesized exhibited moderate molecular weights with rather narrow molecular weight distributions. The values of the glass‐transition temperature (T_g) of the copolymers depend on the molar fractions of cyclic carbonate. For the poly(N‐CBz‐Hpr‐co‐tri‐MC) system, with a decreased tri‐MC content from 93 to 16 mol %, the T_g increased from ?10 to 60 °C. Similarly, for the poly(N‐CBz‐Hpr‐co‐tetra‐MC) system, when the tetra‐MC content decreased from 80 to 8 mol %, the T_g increased from ?18 to 52 °C. The relationship between the poly(N‐CBz‐Hpr‐co‐tri‐MC) T_g and the compositions was in approximation with the Fox equation. In vitro degradation of these poly(N‐CBz‐Hpr‐co‐tri‐MC)s was evaluated from weight‐loss measurements. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1435–1443, 2003     

The synthesis,characterization and polycondensation of metal‐containing diols: crystal structure of [(η5‐C5H5)(CO)2Fe(CH2)3O‐{2,6‐(CH2OH)2‐4‐CH3?C6H2}]

The synthesis of two new transition‐metal‐containing polyesters is described. The precursors are bifunctional organometallic monomers that were synthesized using 2,6‐bis(hydroxymethyl)‐p‐cresol as the key reagent. This was achieved by simple coupling reactions between the appropriate organometallic alkyl halide and the cresol reagent. Polycondensation reactions were carried out with terephthaloyl chloride using ambient temperature solution techniques. The new low molecular weight oligomeric polyesters were characterized using Fourier transform infrared and ¹HNMR spectroscopy, differential scanning calorimetry, thermogravimetric analysis and size‐exclusion chromatography analyses. Copyright © 2002 John Wiley & Sons, Ltd.     

Hetero‐ and homo‐leptic Ru(II) catalyzed synthesis of cyclic carbonates from CO2; Synthesis,spectroscopic characterization and electrochemical properties

Based on the a ligand BDPPZ [(9a,13a‐dihydro‐4,5,9,14‐tetraaza‐benzo[b]triphenylene‐11‐yl)‐phenyl‐methanone] (1) and its polypyridyl hetero‐ and homoleptic Ru(II) metal complexes, [Ru(bpy)₂L](PF₆)₂ (2), [Ru(phen)₂L](PF₆)₂ (3), [Ru(dafo)₂L](PF₆)₂ (4), [Ru(dcbpy)₂L](PF₆)₂ (5) and [RuL₃](PF₆)₂ (6) (where, L = ligand, bpy = 2,2′‐bipyridine, phen = 1,10‐phenantroline, dafo = 4,5‐diazafluoren‐9‐one and dcbpy = 3,3′‐dicarboxy‐2,2′‐bipyridine), have been synthesized and characterized by elemental analysis, UV–vis, FT‐IR, ¹H and ¹³C‐NMR spectra (for ligand), molar conductivity measurements and X‐ray powder techniques. The electrochemical parameters of the substituted ligand and its polypyridyl hetero‐ and homoleptic Ru(II) metal complexes are reported by cyclic voltammetry. UV–vis spectroscopy is used to compare the differences between the conjugated π systems in this ligand and its Ru(II) metal complexes. The polypyridyl hetero‐ and homoleptic Ru(II) metal complexes also tested as catalysts for the formation of cyclic organic carbonates from carbon dioxide and liquid epoxides which served as both reactant and solvent. The results showed that the [Ru(L)₃](PF₆)₂ (6) complex is more efficient than the other Ru(II) complexes for the formation of cyclic organic carbonates from carbon dioxide. Copyright © 2010 John Wiley & Sons, Ltd.     

Copolymerization of propylene oxide and CO2 using achiral salophen Co(III) penta-florobenzoate as catalyst and tetrabutyl ammonium bromide as co-catalyst

Copolymerization of racemic propylene oxide with carbon dioxide is investigated in the presence of economically inexpensive and effective achiral salophenCo(III)X [salophen = N,N'-bis(3,5-di-tert-butylsalicylidene)-phenylenediimine, X = pentaflorobenzoate] catalyst and tetrabutyl ammonium bromide as co-catalyst. Effects of different variables like monomer to catalyst ratio, catalyst/co-catalyst ratio, temperature, pressure of CO₂ on molecular weight, yield and selectivity of poly(propylene carbonate) [PPC] have been investigated. The maximum M_w of 25.8 g/mol has been obtained at 15 bar and 50°C. All the samples were found to have excellent polydispersity near to 1.     

Synthesis and characterization of light‐emitting oligo(p‐phenylene‐vinylene)s and polymeric derivatives containing three‐ and five‐conjugated phenylene rings. II. Electro‐optical properties and optimization of PLED performance

A series of multilayer polymeric light‐emitting diodes (PLEDs) containing an electron‐transporting layer (ETL), that is tris(8‐quinolinolato)‐aluminum(III) (Alq) and 2,2′,2″‐(1,3,5‐phenylene)‐tris[1‐phenyl‐1H‐benzimidazole] (TPBI), were fabricated by doping fluorescent oligo(p‐phenylene‐vinylene)s (BIII and BV) and polymer derivatives (PBV) into poly(N‐vinyl carbazole) (PVK). These PLEDs can be optimized by the design of multilayer device configurations (brightness increased 8–15 times by addition of ETL) and possess greenish electroluminescent (EL) spectra peaked about 500–540 nm. A remarkably high brightness of 56,935 cd/m² with a power efficiency of 3.25 lm/W was obtained in the device of PVK:BVOC₈‐OC₈ (100:20)/Alq (60 nm/60 nm). It suggests that the emission mechanism (including the conjugated and excimer emissions of BVOC₈‐OC₈ emitters) originates from both of BVOC₈‐OC₈ and ETL (Alq and TPBI) by varying the concentration of chromophores and adjusting the thickness of ETL. The concentration effect of the emitters in PVK (i.e. PVK:BVOC₈‐OC₈ = 100:5, 100:20, and 100:100 wt %) and the influence of the ETL (including its thickness) on the EL characteristics are also reported. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2922–2936, 2006     

Double metal cyanide catalyst prepared using H3Co(CN)6 for high carbonate fraction and molecular weight control in carbon dioxide/propylene oxide copolymerization

Simple mixing of H₃Co(CN)₆ and ZnCl₂ in methanol resulted in precipitates of [ZnCl]⁺₂[HCo(CN)₆]^2?, constituting a new type of double metal cyanide (DMC) catalyst exhibiting a high performance in carbon dioxide (CO₂)/propylene oxide (PO) copolymerization. High‐molecular‐weight poly(propylene carbonate‐co‐propylene oxide)s [poly(PC‐co‐PO)s] (M_n～40,000) were consistently obtained with high carbonate fractions (～60 mol %) and a high selectivity (>95%) with the new type of DMC catalyst. Conventional preparation of the DMC catalyst using K₃Co(CN)₆ and ZnCl₂ required removing KCl through thorough washing and resulted in lower carbonate fractions (10–40 mol %), which depended on the washing conditions. Feeding hydrophobic diols such as 1,10‐decanediol as chain transfer agent preserved the high carbonate fraction (～60%) and enabled precise control of the molecular weight, including preparation of a low‐molecular‐weight poly(PC‐co‐PO)‐diol (M_n ～2000), which was a flowing viscous liquid with a low T_g (?30 °C) suitable for polyurethane applications. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4811–4818     

Facile synthesis of poly(ether carbonate)s via copolymerization of CO2 and propylene oxide under combinatorial catalyst of rare earth ternary complex and double metal cyanide complex

Poly(ether carbonate)s (PPCs) with carbonate unit (CU) content ranging from 57.8 to 97.1% and number average molecular weight (M_n) around 100 kg/mol were conveniently prepared via copolymerization of CO₂ and propylene oxide under combinatorial catalyst of rare earth ternary (RET) complex and double metal cyanide (DMC) complex. Enhancement of catalytic activity and reduction of propylene carbonate byproduct were realized due to synergetic effect of the two metal catalysts, where DMC can be activated in the presence of RET. Solubility fractionation confirmed that the obtained PPCs were copolymers, not physical blends of each polymer. Thermal performances of the PPCs were closely related to their CU content, their glass transition temperatures (T_g) were tunable in the range of 6.7–36.3 °C, which decreased with decreasing CU content, while their thermal stabilities were enhanced significantly, an increase of 50.5 °C in 50% weight loss temperature was observed when CU content decreased from 97.1 to 57.8%. Both shear storage modulus and complex viscosity increased with increasing CU content, which became more obvious at lower frequency, featuring well with the CU content in the PPCs. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012