Doping‐Induced Amorphization,Vacancy, and Gradient Energy Band in SnS2 Nanosheet Arrays for Improved Photoelectrochemical Water Splitting

Photoelectrochemical (PEC) water splitting is a promising strategy to convert solar energy into hydrogen fuel. However, the poor bulk charge‐separation ability and slow surface oxygen evolution reaction (OER) dynamics of photoelectrodes impede the performance. We construct In‐ and Zn/In‐doped SnS₂ nanosheet arrays through a hydrothermal method. The doping induces the simultaneous formation of an amorphous layer, S vacancies, and a gradient energy band. This leads to elevated carrier concentrations, an increased number of surface‐reaction sites, accelerated surface‐OER kinetics, and an enhanced bulk‐carrier separation efficiency with a decreased recombination rate. This efficient doping strategy allows to manipulate the morphology, crystallinity, and band structure of photoelectrodes for an improved PEC performance.     

A Plasma‐Triggered O−S Bond and P−N Junction Near the Surface of a SnS2 Nanosheet Array to Enable Efficient Solar Water Oxidation

A photoelectrochemical (PEC) cell can split water into hydrogen and oxygen with the assistance of solar illumination. However, its application is still limited by excessive bulk carrier recombination and sluggish surface oxygen evolution reaction (OER) kinetics. Taking SnS₂ as an example, a promising layered optoelectronic semiconductor, Ar plasma treatment strategy was used to introduce a SnS/SnS₂ P?N heterojunction and O?S bond near the surface of a SnS₂ nanosheet array, simultaneously increasing the separation efficiency of photogenerated electron–hole pairs in the bulk and lowering the OER overpotential at the surface. The onset potential of the plasma‐treated SnS₂ nanosheet array shifts negatively to 0.16 V, and the photocurrent density at 1.23 V vs. RHE boosts to 2.15 mA cm^?2, which is 7 times that of pristine SnS₂. This work demonstrates a facile plasma treatment strategy to modulate the energy band structure and surface chemical states for improved PEC performance.     

Chemical Vapor Deposition of FeOCl Nanosheet Arrays and Their Conversion to Porous α‐Fe2O3 Photoanodes for Photoelectrochemical Water Splitting

FeOCl nanosheet arrays were deposited on fluorine‐doped tin oxide glass substrates through a chemical vapor deposition method and further converted to hematite porous nanosheet arrays. A much enhanced photocurrent was obtained for such hematite films, which was three times higher than that of a planar hematite film at 1.23 V versus a reversible hydrogen reference electrode.     

Heterostructured Inter‐Doped Ruthenium–Cobalt Oxide Hollow Nanosheet Arrays for Highly Efficient Overall Water Splitting

The development of transition‐metal‐oxides (TMOs)‐based bifunctional catalysts toward efficient overall water splitting through delicate control of composition and structure is a challenging task. Herein, the rational design and controllable fabrication of unique heterostructured inter‐doped ruthenium–cobalt oxide [(Ru–Co)O_x] hollow nanosheet arrays on carbon cloth is reported. Benefiting from the desirable compositional and structural advantages of more exposed active sites, optimized electronic structure, and interfacial synergy effect, the (Ru–Co)O_x nanoarrays exhibited outstanding performance as a bifunctional catalyst. Particularly, the catalyst showed a remarkable hydrogen evolution reaction (HER) activity with an overpotential of 44.1 mV at 10 mA cm^?2 and a small Tafel slope of 23.5 mV dec^?1, as well as an excellent oxygen evolution reaction (OER) activity with an overpotential of 171.2 mV at 10 mA cm^?2. As a result, a very low cell voltage of 1.488 V was needed at 10 mA cm^?2 for alkaline overall water splitting.     

Fluorine‐Doped Porous Single‐Crystal Rutile TiO2 Nanorods for Enhancing Photoelectrochemical Water Splitting

Fluorine‐doped hierarchical porous single‐crystal rutile TiO₂ nanorods have been synthesized through a silica template method, in which F^? ions acts as both n‐type dopants and capping agents to make the isotropic growth of the nanorods. The combination of high crystallinity, abundant surface reactive sites, large porosity, and improved electronic conductivity leads to an excellent photoelectrochemical activity. The photoanode made of F‐doped porous single crystals displays a remarkably enhanced solar‐to‐hydrogen conversion efficiency (≈0.35 % at ?0.33 V vs. Ag/AgCl) under 100 mW cm^?2 of AM=1.5 solar simulator illumination that is ten times of the pristine solid TiO₂ single crystals.     

Direct Observation of Oxygen Vacancy Self‐Healing on TiO2 Photocatalysts for Solar Water Splitting

Oxygen vacancy (Vo) on transition metal oxides plays a crucial role in determining their chemical/physical properties. Conversely, the capability to directly detect the changing process of oxygen vacancies (Vos) will be important to realize their full potentials in the related fields. Herein, with a novel synchronous illumination X‐ray photoelectron spectroscopy (SI‐XPS) technique, we found that the surface Vos (surf‐Vos) exhibit a strong selectivity for binding with the water molecules, and sequentially capture an oxygen atom to achieve the anisotropic self‐healing of surface lattice oxygen. After this self‐healing process, the survived subsurface Vos (sub‐Vos) promote the charge excitation from Ti to O atoms due to the enriched electron located on low‐coordinated Ti sites. However, the excessive sub‐Vos would block the charge separation and transfer to TiO₂ surfaces resulted from the destroyed atomic structures. These findings open a new pathway to explore the dynamic changes of Vos and their roles on catalytic properties, not only in metal oxides, but in crystalline materials more generally.     

Subsurface Engineering Induced Fermi Level De-pinning in Metal Oxide Semiconductors for Photoelectrochemical Water Splitting

Photoelectrochemical (PEC) water splitting is a promising approach for renewable solar light conversion. However, surface Fermi level pinning (FLP), caused by surface trap states, severely restricts the PEC activities. Theoretical calculations indicate subsurface oxygen vacancy (sub-O_v) could release the FLP and retain the active structure. A series of metal oxide semiconductors with sub-O_v were prepared through precisely regulated spin-coating and calcination. Etching X-ray photoelectron spectroscopy (XPS), scanning transmission electron microscopy (STEM), and electron energy loss spectra (EELS) demonstrated O_v located at sub ∼2–5 nm region. Mott–Schottky and open circuit photovoltage results confirmed the surface trap states elimination and Fermi level de-pinning. Thus, superior PEC performances of 5.1, 3.4, and 2.1 mA cm⁻² at 1.23 V vs. RHE were achieved on BiVO₄, Bi₂O₃, TiO₂ with outstanding stability for 72 h, outperforming most reported works under the identical conditions.     

Photoelectrochemical and Photovoltaic Characteristics of Amorphous‐Silicon‐Based Tandem Cells as Photocathodes for Water Splitting

In this study amorphous silicon tandem solar cells are successfully utilized as photoelectrodes in a photoelectrochemical cell for water electrolysis. The tandem cells are modified with various amounts of platinum and are combined with a ruthenium oxide counter electrode. In a two‐electrode arrangement this system is capable of splitting water without external bias with a short‐circuit current of 4.50 mA cm^?2. On the assumption that no faradaic losses occur, a solar‐to‐hydrogen efficiency of 5.54 % is achieved. In order to identify the relevant loss processes, additional three‐electrode measurements were performed for each involved half‐cell.     

Surviving High‐Temperature Calcination: ZrO2‐Induced Hematite Nanotubes for Photoelectrochemical Water Oxidation

Nanotubular Fe₂O₃ is a promising photoanode material, and producing morphologies that withstand high‐temperature calcination (HTC) is urgently needed to enhance the photoelectrochemical (PEC) performance. This work describes the design and fabrication of Fe₂O₃ nanotube arrays that survive HTC for the first time. By introducing a ZrO₂ shell on hydrothermal FeOOH nanorods by atomic layer deposition, subsequent high‐temperature solid‐state reaction converts FeOOH‐ZrO₂ nanorods to ZrO₂‐induced Fe₂O₃ nanotubes (Zr‐Fe₂O₃ NTs). The structural evolution of the hematite nanotubes is systematically explored. As a result of the nanostructuring and shortened charge collection distance, the nanotube photoanode shows a greatly improved PEC water oxidation activity, exhibiting a photocurrent density of 1.5 mA cm⁻² at 1.23 V (vs. reversible hydrogen electrode, RHE), which is the highest among hematite nanotube photoanodes without co‐catalysts. Furthermore, a Co‐Pi decorated Zr‐Fe₂O₃ NT photoanode reveals an enhanced onset potential of 0.65 V (vs. RHE) and a photocurrent of 1.87 mA cm⁻² (at 1.23 V vs. RHE).     

Single‐Crystal Semiconductors with Narrow Band Gaps for Solar Water Splitting

Solar water splitting provides a clean and renewable approach to produce hydrogen energy. In recent years, single‐crystal semiconductors such as Si and InP with narrow band gaps have demonstrated excellent performance to drive the half reactions of water splitting through visible light due to their suitable band gaps and low bulk recombination. This Minireview describes recent research advances that successfully overcome the primary obstacles in using these semiconductors as photoelectrodes, including photocorrosion, sluggish reaction kinetics, low photovoltage, and unfavorable planar substrate surface. Surface modification strategies, such as surface protection, cocatalyst loading, surface energetics tuning, and surface texturization are highlighted as the solutions.     

Doping‐Induced Absorption Bands in P3HT: Polarons and Bipolarons

In this work, we focus on the formation of different kinds of charge carriers such as polarons and bipolarons upon p‐type doping (oxidation) of the organic semiconductor poly(3‐ hexylthiophene‐2,5‐diyl) (P3HT). We elucidate the cyclic voltammogram during oxidation of this polymer and present spectroscopic changes upon doping in the UV/Vis/near‐IR range as well as in the mid‐IR range. In the low‐oxidation regime, two absorption bands related to sub‐gap transitions appear, one in the UV/Vis range and another one in the mid‐IR range. The UV/Vis absorption gradually decreases upon further doping while the mid‐IR absorption shifts to lower energy. Additionally, electron paramagnetic resonance (EPR) measurements are performed, showing an increase of the EPR signal up to a certain doping level, which significantly decreases upon further doping. Furthermore, the absorption spectra in the UV/Vis range are analyzed in relation to the morphology (crystalline vs. amorphous) by using theoretical models. Finally, the calculated charge carriers from cyclic voltammogram are linked together with optical transitions as well as with the EPR signals upon p‐type doping. We stress that our results indicate the formation of polarons at low doping levels and the existence of bipolarons at high doping levels. The presented spectroscopic data are an experimental evidence of the formation of bipolarons in P3HT.     

Hierarchical NiCo2S4 Nanotube@NiCo2S4 Nanosheet Arrays on Ni Foam for High‐Performance Supercapacitors

Hierarchical NiCo₂S₄ nanotube@NiCo₂S₄ nanosheet arrays on Ni foam have been successfully synthesized. Owing to the unique hierarchical structure, enhanced capacitive performance can be attained. A specific capacitance up to 4.38 F cm^?2 is attained at 5 mA cm^?2, which is much higher than the specific capacitance values of NiCo₂O₄ nanosheet arrays, NiCo₂S₄ nanosheet arrays and NiCo₂S₄ nanotube arrays on Ni foam. The hierarchical NiCo₂S₄ nanostructure shows superior cycling stability; after 5000 cycles, the specific capacitance still maintains 3.5 F cm^?2. In addition, through the morphology and crystal structure measurement after cycling stability test, it is found that the NiCo₂S₄ electroactive materials are gradually corroded; however, the NiCo₂S₄ phase can still be well‐maintained. Our results show that hierarchical NiCo₂S₄ nanostructures are suitable electroactive materials for high performance supercapacitors.     

Light‐Induced Water Splitting Causes High‐Amplitude Oscillation of pH‐Sensitive Layer‐by‐Layer Assemblies on TiO2

We introduce a simple concept of a light induced pH change, followed by high amplitude manipulation of the mechanical properties of an adjacent polymer film. Irradiation of a titania surface is known to cause water splitting, and this can be used to reduce the environmental pH to pH 4. The mechanical modulus of an adjacent pH sensitive polymer film can thus be changed by more than an order of magnitude. The changes can be localized, maintained for hours and repeated without material destruction.     

Uniformly Dispersed and Controllable Ligand‐Free Silver‐Nanoparticle‐Decorated TiO2 Nanotube Arrays with Enhanced Photoelectrochemical Behaviors

Homogeneously dispersed silver nanoparticles (AgNPs) were successfully decorated onto the surface of TiO₂ nanotube arrays (TNTA) by means of an in situ photoreduction method. TNTA films as supports exhibit excellent properties to prevent agglomeration of AgNPs, and they also avoid using polymer ligands, which is deleterious to enhancing the properties of the fabricated NPs. The silver particle size and its content could be controlled just by changing the immersion time. Detailed SEM and TEM analyses combined with energy‐dispersive X‐ray spectroscopy analyses with different immersion times (5, 10, 30, 60 min) have revealed the variation tendency. The prepared Ag/TNTA composite films were also characterized by XRD, X‐ray photoelectron spectroscopy, and high‐resolution TEM. The UV/Vis diffuse reflectance spectra displayed a redshift of the absorption peak with the growth of AgNPs. The photocurrent response and the photoelectrocatalytic degradation of methyl orange (MO) were used to evaluate the photoelectrochemical properties of the fabricated samples. The results showed that the photocurrent response and photoelectrocatalytic activity largely depended on the loaded Ag particle size and content. TNTA films with a diameter of 17.92 nm and silver content of 1.15 at % showed the highest photocurrent response and degradation rate of MO. The enhanced properties could be attributed to the synergistic effect between AgNPs and TiO₂. To make good use of this effect, particle size and silver content should be well controlled to develop the electron charge and discharge process during the photoelectrical process. Neither smaller nor larger AgNPs caused decreased photoelectrical properties.     

Acceptor-Doping Accelerated Charge Separation in Cu2O Photocathode for Photoelectrochemical Water Splitting: Theoretical and Experimental Studies

Cu₂O is a typical photoelectrocatalyst for sustainable hydrogen production, while the fast charge recombination hinders its further development. Herein, Ni²⁺ cations have been doped into a Cu₂O lattice (named as Ni-Cu₂O) by a simple hydrothermal method and act as electron traps. Theoretical results predict that the Ni dopants produce an acceptor impurity level and lower the energy barrier of hydrogen evolution. Photoelectrochemical (PEC) measurements demonstrate that Ni-Cu₂O exhibits a photocurrent density of 0.83 mA cm⁻², which is 1.34 times higher than that of Cu₂O. And the photostability has been enhanced by 7.81 times. Moreover, characterizations confirm the enhanced light-harvesting, facilitated charge separation and transfer, prolonged charge lifetime, and increased carrier concentration of Ni-Cu₂O. This work provides deep insight into how acceptor-doping modifies the electronic structure and optimizes the PEC process.