Chain extension of adipic acid and (or) succinic acid/butanediol polyesters with 2,2′‐(1,4‐phenylene)‐bis(2‐oxazoline) and adipoylbiscaprolactamate combined chain extenders

This paper provided an easy and flexible method to synthesize high molecular weight polyesters by polycondensation and chain extension. Low molecular weight polybutylene adipate, polybutylene succinate, and poly(butylene succinate‐co‐butylene adipate) (PBSA) were synthesized through melt condensation polymerization from adipic acid and/or succinic acid with butanediol. The prepolyesters obtained had different amount of ? COOH and ? OH terminal groups. Chain extension of them was carried out at 180–240°C using 2,2′‐(1,4‐phenylene)‐bis(2‐oxazoline) and adipoyl biscaprolactamate as combined chain extenders. The influencing factors of the chain extension were studied. At the optimal conditions, chain‐extended polybutylene adipate with M_n up to 39,100, polybutylene succinate with intrinsic viscosity of 0.99 dl/g, and PBSA with intrinsic viscosity from 0.73 to 0.81 dl/g were synthesized. The chain‐extended polyesters were characterized by IR spectrum, ¹H NMR spectrum, differential scanning calorimetry, thermogravimetric analysis (TGA), wide angle X‐ray scattering, and tensile test. The thermal analysis showed that chain extension often led to slight decrease of the regularity, the crystallinity, and the melting point. This deterioration of the properties is not harmful enough to impair their thermal properties and obstruct them from being used as biodegradable thermoplastics. The TGA showed that the chain‐extended polyesters were stable with initial decomposition temperature over 354.7°C. The tensile strength of the chain extended PBS and PBSAs with butylene adipate units less than 20 mol% was in the range of 18.95–31.22 MPa. Copyright © 2010 John Wiley & Sons, Ltd.     

Mannose‐based graft polyesters with tunable binding affinity to concanavalin A

Glycopolymers have been widely used to understand the interactions between carbohydrates and lectins, which facilitate the diagnosis and detection of disease and pathogens as well as the development of vaccines. While studies have been focused on the correlation of glycopolymer structure and their binding to lectins, graft‐type glycopolyesters are uncommon. Herein, we report the design and synthesis of mannose‐based graft polyesters by “grafting‐from” method and investigate their interactions with Concanavalin A (Con A). As confirmed by ¹H NMR spectroscopy and sulfuric acid‐UV method, graft polyesters with different lengths of mannose graft were successfully synthesized. Our results from turbidimetry binding assay showed that graft polyesters with longer mannose graft exhibit higher initial binding rate (k_i). Isothermal titration calorimetry measurements of these graft polyesters with Con A showed that polymers exhibit higher binding affinity (k_a) with the number of side chain mannose. This study provides understanding of the interaction between Con A and mannose‐based graft polyesters, which can be employed for the development of glycopolymeric therapeutics. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3908–3917     

Unsaturated,biobased polyesters and their cross‐linking via radical copolymerization

Biobased, unsaturated polyesters derived from isosorbide, maleic anhydride, and succinic acid were synthesized and characterized. The presence of maleic anhydride units in the structure of the polyesters allowed converting them into cured coatings by radical copolymerization with crosslinking agents such as 2‐hydroxyethyl methacrylate, N‐vinyl‐2‐pyrrolidinone, acrylic acid or methacrylamide. The investigated polyesters were obtained via bulk polycondensation, catalyzed by titanium(IV) n‐butoxide. 2D NMR and MALDI‐Tof‐MS spectroscopy proved that this polymerization resulted in isomerization of maleic acid units into fumaric ones and in the formation of slightly branched structures by the reaction of isosorbide (end) groups with main chain unsaturated bonds. Moreover, some double bonds proved to have reacted with the condensation by‐product water. The resulting polyesters displayed the expected correlation between variables such as molecular weight and content of unsaturated bonds and their T_g values. Since the thermal properties of the obtained polyesters were appropriate for coating applications, the polymers were crosslinked with unsaturated monomers by radical copolymerization. The crosslinking process was studied using FTIR spectroscopy and by measurements of the soluble part of the cured coatings. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2885–2895, 2010     

Liquid‐crystalline azobenzene‐containing ferrocene‐based polymers: study on synthesis and properties of main‐chain ferrocene‐based polyesters with azobenzene in the side chain

Ferrocene‐based polymers are characterized by their electrochemical activity, good redox properties, thermal, photochemical stability, and liquid crystallinity, and thus they have various applications in different fields. A comprehensive investigation on the synthesis and properties of three novel main‐chain ferrocene‐based polyesters with azobenzene in the side chain (MFPAS) was carried out. The main‐chain ferrocene‐based polyester, poly(N‐phenyldiethanolamine 1,1′‐ferrocene dicarboxylate (PPFD), was synthesized via the solution polycondensation reaction of 1,1′‐ferrocenedicarbonyl chloride with phenyldiethanolamine (PDE). The novel MFPAS were synthesized via the post‐polymerization azo‐coupling reaction of PPFD with three different 4‐substituted anilines including 4‐nitroaniline, 4‐aminobenzoic acid, and 4‐aminobenzonitrile to produce 4‐nitrophenylazo‐functionalized‐PPFD (PPFD‐NT), 4‐carboxyphenylazo‐functionalized‐PPFD (PPFD‐CA), and 4‐cyanophenylazo‐functionalized‐PPFD (PPFD‐CN), respectively. All the synthesized polymers were characterized by ¹H NMR spectroscopy, Fourier transform infrared spectroscopy, and UV–visible spectroscopy. In addition, powder X‐ray diffraction patterns were measured for the synthesized polymers. The photoisomerization of the MFPAS was studied. The thermal properties of the MFPAS were studied using thermogravimetric analysis and differential scanning calorimetry. PPFD‐CA and PPFD‐CN were found to be more thermally stable than PPFD‐NT. Finally, the liquid‐crystalline properties of PPFD and the MFPAS were examined using polarized optical microscope. It was found that all the polymers possessed nematic phases and exhibited textures with schlieren disclinations. Copyright © 2012 John Wiley & Sons, Ltd.     

Thermotropic liquid‐crystalline polymers containing five‐membered heterocyclic groups. X. Relationships between structures of semirigid polyesters based on three disubstituted 2,5‐diphenyl‐1,3,4‐thiadiazoles and thermotropic liquid‐crystalline and optical properties

Thermotropic liquid‐crystalline (LC) semirigid polyesters based on three terphenyl analogues of 1,3,4‐thiadiazole (2,5‐diphenyl‐1,3,4‐thiadiazole)s (DPTD) linking undecamethyleneoxy chain at different substituted positions were synthesized from three disubstituted (4,4′‐, 3,4′‐, and 3,3′‐) dioxydiundecanols of DPTD and four diesters, and the relationships between polymer structures and LC and optical properties were investigated. DSC measurements, texture observations, and wide‐angle X‐ray analyses revealed that the polymers composed of DPTD moiety having a more linear molecular structure and 1,4‐phenylene unit or short aliphatic chain tend to exhibit LC smectic C and/or A phases. The following observations were made: (1) the emergence of smectic C and/or A phases in all the polymers on the basis of 4,4′‐disubstituted DPTD, (2) formation of enantiotropic smectic C and/or A phases in the polymers containing a 1,4‐phenylene unit in the main chain, (3) formation of a more stable smectic C phase in the polymers having a short aliphatic [(CH₂)₄] chain, and (4) a decrease of the mesomorphic property of the polyesters in the order of 4,4′‐DPTD > 3,4′‐DPTD > 3,3′‐DPTD. Solution and solid‐state ultraviolet–visible and photoluminescent spectra indicated that all the polyesters display maximum absorbances and blue emissions arising from the DPTD moiety, whose peak maxima were shifted to lower wavelengths in the order of 4,4′‐DPTD > 3,4′‐DPTD > 3,3′‐DPTD as well as the aforementioned LC property. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2676–2687, 2003     

Efficient one‐pot synthesis of water‐compatible and photoresponsive molecularly imprinted polymer nanoparticles by facile RAFT precipitation polymerization

A facile, general, and highly efficient one‐pot approach to obtain azobenzene (azo)‐containing molecularly imprinted polymer (MIP) nanoparticles with photoresponsive template binding and release properties in aqueous media is described, which involves the combined use of hydrophilic macromolecular chain transfer agent‐mediated reversible addition‐fragmentation chain transfer precipitation polymerization and easily available water‐insoluble azo functional monomers. The resulting azo‐containing MIPs were characterized with dynamic laser scattering (DLS), SEM, FTIR, static contact angle and water dispersion studies, and equilibrium binding experiments. They have proven to be nanoparticles (their diameters being around 104–397 nm, as determined by DLS in methanol) with surface‐grafted hydrophilic polymer brushes and exhibit excellent pure water‐compatible template binding properties. Moreover, obvious photoregulated template binding behaviors were observed for such azo‐containing MIP nanoparticles, which led to their largely accelerated template release in the aqueous media under the UV light irradiation. Furthermore, the general applicability of the strategy was also demonstrated. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1941–1952     

Antimicrobial Hydantoin‐Containing Polyesters

A new N‐hydantoin‐containing biocompatible and enzymatically degradable polyester with antibacterial properties is presented. Different polyesters of dimethyl succinate, 1,4‐butanediol, and 3‐[N,N‐di(β‐hydroxyethyl)aminoethyl]‐5,5‐dimethylhydantoin in varying molar ratios are prepared via two‐step melt polycondensation. The antibacterially active N‐halamine form is obtained by subsequent chlorination of the polyesters with sodium hypochlorite. Chemical structures, thermal properties, and spherulitic morphologies of the copolymers are studied adopting FT‐IR, NMR, TGA, DSC, WAXD, and POM. The polyesters exhibit antibacterial activity against Escherichia coli. The adopted synthetic approach can be transferred to other polyesters in a straightforward manner.

     

Renewable Polyethers via GaBr3‐Catalyzed Reduction of Polyesters

Herein, a novel approach is reported for the synthesis of medium‐ and long‐chain aliphatic polyethers 2 based on the GaBr₃‐catalysed reduction of polyesters 1 with TMDS as the reducing agent. Thus, various linear and branched aliphatic polyesters 1 were prepared and systematically investigated for this reduction strategy, demonstrating the applicability and versatility of this new polyether synthesis protocol. Medium‐ and long‐chain chain polyethers were obtained from the respective polyesters without or with minor chain degradation, whereas short‐chain polyesters, such as poly‐l ‐lactide 1 i and poly[(R)‐3‐hydroxybutanoate] 1 j , showed major chain degradation. In this way, previously unavailable and uncommon polyethers were obtained and studied.     

“Click polyester”: Synthesis of polyesters containing triazole units in the main chain via safe and rapid “click” chemistry and their properties

Click Cu(I)‐catalyzed polymerizations of diynes that contained ester linkages and diazides were performed to produce polyesters (click polyesters) of large molecular weights [(～1.0–7.0 ) × 10⁴], that contained main‐chain 1,4‐disubstitued triazoles in excellent yields. Incorporation of triazole improved the thermal properties and magnified the even‐odd effect of the methylene chain length. We also found that, by changing the positions of the triazole rings, the thermal properties of the polyesters could be controlled. The use of in situ azidation was a safe reaction, as explosive diazides are not used. In addition, the microwave heating was found to accelerate the polymerization rates. This is the first study that has applied click chemistry for the synthesis of a series of polyesters. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4207–4218, 2010     

Polyesters containing sulfur. VII. New aliphatic‐aromatic polyesters for synthesis of polyester‐sulfur compositions and polyurethanes

New linear polyesters containing sulfur in the main chain were obtained by melt polycondensation of diphenylmethane‐4,4′‐bis(methylthioacetic acid) (DBMTAA) or diphenylmethane‐4,4′‐bis(methythiopropionic acid) (DBMTPA) and diphenylmethane‐4,4′‐bis(methylthioethanol) (DBMTE) at equimolar ratio of reagents (polyesters E‐A and E‐P) as well as at 0.15 molar excess of diol (polyesters E‐A_OH and E‐P_OH). The kinetics of these reactions was studied at 150, 160, and 170°C. Reaction rate constants (k₂) and activation parameters (ΔG^≠, ΔH^≠, ΔS^≠) from carboxyl group loss were determined using classical kinetic methods. E‐A and E‐P (M̄_n = 4400, 4600) were used for synthesis of new rubber‐like polyester‐sulfur compositions, by heating with elemental sulfur, whereas oligoesterols E‐A_OH and E‐P_OH (M̄_n = 2500, 2900) were converted to thermoplastic polyurethane elastomers by reaction with hexamethylene diisocyanate (HDI) or methylene bis(4‐phenyl isocyanate) (MDI). The structure of the polymers was determined by elemental analysis, FT‐IR and liquid or solid‐state ¹H‐, ¹³C‐NMR spectroscopy, and X‐ray diffraction analysis. Thermal properties were measured by DTA, TGA, and DSC. Hardness and tensile properties of polyurethanes and polyester‐sulfur compositions were also determined. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 835–848, 1999     

A facile method to synthesize high‐molecular‐weight biobased polyesters from 2,5‐furandicarboxylic acid and long‐chain diols

In this study, biobased furan dicarboxylate polyesters have been prepared using 2,5‐furandicarboxylic acid (FDCA) and diols with high number of methylene groups (long‐chain diols), namely, 8, 9, 10, and 12. Because of the high boiling points of these diols, a modified procedure of the well‐known melt polycondensation was applied in this work. According to this, the dimethyl ester of FDCA (DMFD) reacted in the first transesterification stage with the corresponding diols forming bis‐hydroxy‐alkylene furan dicarboxylates (BHFD). In the second stage, the BHFD reacted with DMFD again at temperatures of 150–170 °C (for 4–5 h), and in the final stage, the temperature was raised to 210–230 °C (vacuum was applied for 2–3 h). The molecular weight of the polyesters and the content of oligomers, as was verified by gel permeation chromatography analysis, depend on the polycondensation time and temperature. The chemical structure of the polyesters was verified from ¹H NMR spectroscopy. All the polymers were found to be semicrystalline, with melting temperatures from 69 to 140 °C depending on the diol used. In addition, the mechanical properties also varied with the type of diol. The higher values were observed for poly(octylene 2,5‐furanoate), whereas the lowest values were observed for poly(dodecylene 2,5‐furanoate) with the higher number of methylene groups in its repeating unit. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2617–2632     

Comparison of glass transition and interpretation on miscibility in blends of amorphous poly(vinyl methyl ether) with highly crystallizable versus less‐crystallizable polyesters

Various phase behavior of blends of poly(vinyl ether)s with polyesters of two types (highly crystalline and less crystalline with different main‐chains) were examined using differential scanning calorimetry (DSC) and optical microscopy (OM). Effects of varying the main‐chain polarity of the constituent polyesters on the phase behavior of the blends were analyzed. Miscibility in PVME/polyester blends was found only in polyesters with backbone CH₂/CO ratio = 3.5 to 7.0). T_g‐composition relationships for blends of PVME with highly crystalline polyesters (PBA, PHS) were found to differ significantly from those for PVME blends with less‐crystalline polyesters (PTA, PEAz). Crystallinity of highly crystalline polyester constituents in blends caused significant asymmetry in the T_g‐composition relationships, and induced positive deviation of blends' T_g above linearity; on the other hand, blends of PVME with less crystalline polyesters exhibit typical Fox or Gordon‐Taylor types of relationships. The χ parameters for the miscible blends were found to range from ?0.17 to ?0.33, reflecting generally weak interactions. Phase behavior was analyzed and compared among blends of PVME with rapidly crystallizing vs. less‐crystallizing polyesters, respectively. Effects of polyesters' crystallinity and structures on phase behavior of PVME/polyester blends are discussed. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2899–2911, 2007     

Synthesis and characterization of new soluble cardo polyesters derived from 1,1‐bis‐[4‐(4‐chlorocarboxyphenoxy)phenyl]‐4‐tert‐butylcyclohexane with various bisphenols by solution polycondensation

A new cardo diacid chloride, 1,1‐bis‐[4‐(4‐chlorocarboxyphenoxy)phenyl]‐4‐tert‐butylcyclohexane ( 4 ), was synthesized from 1,1‐bis‐[4‐(4‐carboxyphenoxy)phenyl]‐4‐tert‐butylcyclohexane in refluxing thionyl chloride. Subsequently, various new polyesters were prepared from 4 with various bisphenols by solution polycondensation in nitrobenzene using pyridine as a hydrogen chloride quencher at 150 °C. These polyesters were produced with inherent viscosities of 0.32–0.50 dL · g^?1. Most of these polyesters exhibited excellent solubility in a variety of solvents such as N,N‐dimethylformamide, tetrahydrofuran, tetrachloroethane, dimethyl sulfoxide, N,N‐dimethylacetamide, N‐methyl‐2‐pyrrolidinone, m‐cresol, o‐chlorophenol, and chloroform. These polymers showed glass‐transition temperatures (T_g's) between 144 and 197 °C. The polymer containing the adamantane group exhibited the highest T_g value. The 10% weight loss temperatures of the polyesters, measured by thermogravimetric analysis, were found to be in the range of 426–451 °C in nitrogen. These cardo polyesters exhibited higher T_g's and better solubility than bisphenol A‐based polyesters. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2951–2956, 2001     

RIS Models and Unperturbed Chain Properties of Polyesters Containing 1,3‐Cyclobutylene and 1,4‐Cyclohexylene Linkages

Polyesters containing 1,3‐cyclobutylene and 1,4‐cyclohexylene linkages in the main chain are investigated using conformational energy calculations. Rotational isomeric state (RIS) models are developed for poly(1,4‐cyclohexylenedimethylene terephthalate) (PCT), poly(1,4‐cyclohexylenedimethylene 2,5‐dimethylterephthalate) (DMPCT), poly(1,4‐cyclohexylenedimethylene 1,4‐cyclohexylenedicarboxylate) (PCC), and poly(2,2,4,4‐tetramethyl‐1,3‐cyclobutylene terephthalate) (CBDO). In DMPCT, the ester linkage prefers skewed conformations with respect to the phenyl group to relieve the steric strain caused by the methyl groups. The methyl groups on the cyclobutanediol moiety in CBDO restrict the rotational freedom about the oxycyclobutylene linkage. The unperturbed dimensions as described by characteristic ratio and persistence length are calculated for the trans and cis configurations of these polyesters. CBDO shows highly extended chain conformations among these polyesters indicating relative chain rigidity of the backbone. For DMPCT and PCC, in their trans configuration, the chain dimensions decrease with an increase in temperature while for their cis configurations, the chain dimensions increase with temperature, arising from basic differences in the fragment structures that control the competition of the relative populations as affected by temperature. Temperature has negligible influence on the unperturbed dimensions of both isomeric linkages of CBDO, while this is true for the trans configuration of PCT. The study shows that induction of cyclobutylene groups in the main chain results in a greater rigidity for homopolyesters than for chains with cyclohexylene groups.

Structure of the repeat units of polyesters in the planar trans configuration and the schematic of the RIS models with definition of geometrical parameters.     

Synthesis and characterization of novel renewable polyesters based on 2,5‐furandicarboxylic acid and 2,3‐butanediol

Novel polyesters from 2,5‐furandicarboxylic acid or 2,5‐dimethyl‐furandicarboxylate and 2,3‐butanediol have been synthesized via bulk polycondensation catalyzed by titanium (IV) n‐butoxide, tin (IV) ethylhexanoate, or zirconium (IV) butoxide. The polymers were analyzed by size exclusion chromatography, nuclear magnetic resonance spectroscopy, Fourier transform infrared spectroscopy (FTIR), matrix‐assisted laser ionization‐desorption time‐of‐flight mass spectrometry, electrospray ionization time‐of‐flight mass spectrometry, electrospray ionization quadruple time‐of‐flight mass spectroscopy, thermogravimetric analysis, and differential scanning calorimetry. Fully bio‐based polyesters with number average molecular weights ranging from 2 to 7 kg/mol were obtained which can be suitable for coating applications. The analysis of their thermal properties proved that these polyesters are thermally stable up to 270–300 °C, whereas their glass transition temperature (T_g) values were found between 70 and 110 °C. Furthermore, a material was prepared with a molecular weight of 13 kg/mol, with a T_g of 113 °C. This high T_g would make this material possibly suitable for hot‐fill applications. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis of chitosan‐based thermo‐ and pH‐responsive porous nanoparticles by temperature‐dependent self‐assembly method and their application in drug release

In this research, thermo‐ and pH‐responsive chitosan‐based porous nanoparticles were prepared by the temperature‐dependent self assembly method. The chitosan‐graft‐poly(N‐isopropylacrylamide) (CS‐g‐PNIPAAm) copolymer solution was prepared through polymerization of N‐isopropylacrylamide (NIPAAm) monomer in the presence of chitosan (CS) solution using cerium ammounium nitrate as the initiator. Then, CS‐g‐PNIPAAm solution was diluted by deionized water and heated to 40 °C for CS‐g‐PNIPAAm self‐assembly. After that, CS‐g‐PNIPAAm assembled to form micelles in which shell layer was CS. Crosslinking agent was used to reinforce the micelle structure to form nanoparticle. The molar ratio of CS/NIPAAm in the feed mixture was changed to investigate its effect on structure, morphology, thermal‐ and pH‐responsive properties of the nanoparticles. TEM images showed that a porous structure of nanoparticles was developed. The synthesized nanoparticles carried positive charges on the surface and exhibited stimuli‐responsive properties, and their mean diameter thus could be manipulated by changing pH value and temperature of the environment. The nanoparticles showed a continuous release of the encapsulated doxycycline hyclate up to 10 days during an in‐vitro release experiment. These porous particles with environmentally sensitive properties are expected to be utilized in hydrophilic drug delivery system. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5126–5136, 2009     

Synthesis and characterization of conducting poly(aniline‐co‐o‐aminophenethyl alcohol)s

Poly(o‐aminophenethyl alcohol) and its copolymers containing the aniline unit were synthesized in aqueous hydrochloric acid medium by chemical oxidative polymerization. The chemical composition of these novel polymers was determined spectroscopically, and their viscosities were measured. These polymers exhibit good solubility in organic solvents that is attributed mainly to the polar hydroxyethyl side groups. Their structures (chain conformation and morphological structure) and properties (conductivity, electrochemical characteristics, glass transition, and degradation behavior) were characterized and then interpreted on the basis of the chemical composition along with the electronic and steric hindrance effects associated with the hydroxyethyl side group. Overall, the side group has a significant effect on the polymerization and influences the structure, chain conformation, and properties of the resultant polymer. The poly(aniline‐co‐o‐aminophenethyl alcohol)s containing 20–40 mol % o‐aminophenethyl alcohol units are potential conducting materials for microelectronic and electromagnetic shielding applications because they are easier to process than polyaniline but retain its beneficial properties. These polymers can also be used as a functional conducting polymer intermediate owing to the reactivity of the side group. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 983–994, 2002     

Side chain liquid crystalline diethanolamine‐based polyesters with methoxy and/or nitroazobenzene mesogenic moieties

Side‐chain polyesters based on diethanolamine and 5‐hydroxyisophthalic acid with mesogenic methoxyazobenzene and nitroazobenzene groups were synthesized and their liquid crystalline properties were examined.

Four different types of polyesters were prepared by using various combinations of monomers differing in the mesogen group and the length of the spacer. The thermal and structural properties depend on the type of polyester as well as on the side chain length. The glass transition and isotropization temperatures increase when the methoxyazobenzene group is bound to a diol and decrease when it is bound to an isophthalic acid. Most of the polyesters are thermotropic liquid crystals and form a nematic phase on heating. Some polyesters exhibit shear induced isotropisation to nematic transition up to 25°C above the isotropization temperature.     

Stimuli‐responsive amphiphilic PDMAEMA‐b‐PLMA copolymers and their cationic and zwitterionic analogs

In this work, the synthesis and characterization of novel amphiphilic diblock copolymers of poly(2‐dimethylamino ethyl methacrylate)‐b‐poly(lauryl methacrylate), PDMAEMA‐b‐PLMA, using the reversible addition‐fragmentation chain transfer (RAFT) polymerization technique, are reported. The diblocks were successfully derivatized to cationic and zwitterionic block polyelectrolytes by quaternization and sulfobetainization of the PDMAEMA block, respectively. Furthermore, their molecular and physicochemical characterization was performed by using characterization techniques such as NMR and FTIR, size exclusion chromatography, light scattering techniques, and transmission electron microscopy. The structure of the diblock micelles, their behavior, and properties in aqueous solution were investigated under the effect of pH, temperature, and ionic strength, as PDMAEMA and its derivatives are stimuli‐responsive polymers and exhibit responses to variations of at least one of these physicochemical parameters. These new families of stimuli‐responsive block copolymers respond to changes of their environment giving interesting nanostructures, behavioral motifs, and properties, rendering them useful as nanocarriers for drug delivery and gene therapy. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 598–610     

Supramolecular Graft Copolymerization of a Polyester by Guest‐Selective Encapsulation of a Self‐Assembled Capsule

Repeating guest units of polyesters poly‐(R )‐ 2 were selectively encapsulated by capsule 1 (BF₄)₄ to produce supramolecular graft polymers. The encapsulation of the guest units was confirmed by ¹H NMR spectroscopy. The graft polymer structures were confirmed by the increase in the hydrodynamic radii and the solution viscosities of the polyesters upon complexation of the capsule. After the capsule was formed, atomic force microscopy showed extension of the polyester chains. The introduction of the graft chains onto poly‐(R )‐ 2 resulted in the main chain of the polymer having an M ‐helical morphology. The complexation of copolymers poly‐[(R )‐ 2 ‐co ‐(S )‐ 2 ] by the capsule gave rise to the unique chiral amplification known as the majority‐rules effect.