五层对称人工超常材料结构的表面等离子体激元

研究了由左手材料、负介电材料、常规介电材料所构成的几种五层对称结构表面等离子体激元的特性.讨论了表面等离子体激元的存在区域、色散关系、以及p和s偏振的表面色散曲线枝,发现表面模的性质强烈依赖于系统的组成材料及其组合方式|层数越多,表面色散曲线枝也越多,处在频率通带的表面极化模态也越多|在五层结构中有p和s两种偏振的表面等离子体激元,在共振时,可导致p波和s波强透射.此外,通过使用衰减全反射方法,探讨了激发并观察表面等离子体激元的可能性.     

金属异质波导阵列中的表面等离激元传播特性

提出了一种新的一维金属异质波导阵列的设计方案,即波导芯区周期调制的金属波导阵列.数值模拟的结果表明,金属波导芯区的周期调制引起波导中传播的表面等离激元有效折射率的周期调制,从而可在特定的波段打开一个表面等离激元带隙(如1550nm附近).通过引入合适的缺陷波导单元,可获得特定波长的高品质因子(Q=556)的表面电磁模共振.这一结果可用于设计亚波长的布拉格反射器、光发射器、滤波器等,有可能被用于未来的集成光路.     

不同周期数牛眼结构对基于伪表面等离子激发的太赫兹透射的影响

为研究不同周期数的牛眼结构对太赫兹透射的影响,本文利用微机械加工方法,在铝板上分别制作5个圆环凹槽和15个圆环凹槽两种牛眼结构,并利用时域太赫兹波谱系统,对比了这两种不同周期数的牛眼结构的太赫兹时域信号和频域信号.实验结果显示,0.1~2.7THz宽频太赫兹参考信号可以被两种不同周期数的牛眼结构滤成窄带信号,中心峰值均在约0.53THz处,在该值处,5个圆环凹槽的透射率约为55.7%,15个圆环凹槽的透射率约为68.3%,1THz以上高频信号都被基本滤除,小周期数样品与大周期数样品太赫兹透射谱信号带宽与幅值的差别主要是由于周期性展开不足及边缘泄漏所引起.本文利用伪表面等离子理论解释了滤波效果,并通过有限元方法模拟仿真了宽频太赫兹信号通过不同周期数的牛眼结构后的样品信号,模拟结果与实验结果符合得较好,证实了不同周期数的牛眼结构对太赫兹电磁波的增透效应是不同的.     

Otto结构加载MIM波导的表面等离子激元传输与衰减特性

设计了加载MIM波导的Otto结构研究SPPs的传输和衰减特性,应用球面EM场的解法求解了整个介质区域的本征函数的特征值。对SiO₂厚度分别为750 nm和1 500 nm的设计结构进行了仿真,结果表明:750 nm改进结构的TM₀传播常数达到了1.541,衰减系数仅仅为2.80;随着SiO₂层介质厚度的减小,反射系数随之增大,且不同金属介电常数的谐振方向变化趋势一致;随着腔厚度的减小,在反射相位减少的同时其存储能量也随之减少。     

三层不对称人工电磁材料界面处表面等离子体激元的理论研究

从P和S偏振出发.研究了由常规材料/左手材料/负介电常数材料、及常规材料/左手材料/负磁导率材料这两种三层不对称结构界面上表面等离子体激元(Surface plasmon polaritons,SPPs)的存在区域、色散曲线及其激发.观察到表面等离子体激元的性质强烈地依赖于人工电磁材料的组成参量,例如介质板的厚度和等离子体的频率.最后,使用衰减全反射(Attenuated total reflection,ATR)技术,探究了激发和观察表面等离子体激元的可能性.并针对P和s偏振两种情况计算了衰减全反射光谱.     

基于表面等等离波子的新型Y分支波导

新型高效的纳米光波导器件的研制纳米集成光学的核心技术之一。Y分支波导作为最基本的分光和光路连接元件是纳米光学器件设计与制备的基础。运用时域有限差分(FDTD)法,模拟计算了基于表面等等离波子(SPP)的纳米Y分支波导的传输特性。结果表明,该新型Y分支波导在光通信波段可以实现大角度的分光功能,且在180°分支情况下,传输效率仍高达92.8%以上。另外,该波导还具有导波性能良好、对分叉处间隙缺陷大小不敏感及制作容差较大和器件尺寸在纳米量级等特点。对该新型光波导器件的研究为未来纳米集成光学器件的研制和应用有一定的指导意义。     

一种石墨烯波导褶皱激发表面等离子体激元的设计

设计了褶皱石墨烯波导结构激发表面等离子体激元,通过设计周期阵列结构实现了表面等离子体激元传播损耗的补偿.理论分析了周期阵列结构的表面等离子体激元传播模型和补偿损耗的方式,结果表明褶皱衍射激发表面等离子体激元波导不仅能够激发表面等离子体激元,还能利用表面等离子体激元波矢关系实现器件参数控制,周期阵列增益全程补偿损耗的方式可以显著增加表面等离子体激元的传播距离.数值分析结果进一步表明:该结构具备了保持亚波长尺寸的强局域化优势;周期阵列增益全程补偿可以显著提高纳米腔中的电场强度,降低传输损耗;波导结构的粒子反转水平较高,自发辐射噪声的扰动较低.设计的石墨烯波导器件可以为微纳光学集成、光子传感和测量等领域提供理想的亚波长光子器件.     

Planar Spoof Surface Plasmon Polariton Antenna by Using Transmissive Phase Gradient Metasurface

Spoof surface plasmon polariton (SSPP) antennas are of particular importance in communication and radar systems. Currently available SSPP radiation devices are limited to low performance with high side-lobes because it is extremely challenging to accurately control the wave vector of SSPP and the inherent momentum mismatch between the SSPP and spatial waves. Inspired by the optical principle of reversibility, high-performance radiation control of SSPP is proposed to be achieved with transmissive phase gradient metasurface (TPGM). The TPGM, placed a meticulously optimized distance above the SSPP propagation structure, can provide an additional opposite wave vector to match the momentum between the SSPP and spatial waves. When the propagating SSPP transmits on the TPGM, it can be decoupled into the free space accurately and flexibly. Numerical results coincide well with the measurements, indicating that the radiation control of SSPP achieves high-performance and low side-lobe within 9 to 10.5 GHz with the measured radiation efficiency higher than 50%. The measured maximum efficiency appears at 9.8 GHz for 69%. Thanks to the flexible and accurate manipulation of the dispersion relation of SSPP provided by TPGM, the findings may open an avenue in achieving larger angle scanning antenna.     

介质填充浅槽周期结构表面上的太赫兹表面等离子体激元

通过在金属表面刻成浅的垂直凹槽,并在槽内填充不同的介质,对金属表面浅槽周期结构上传播的表面等离子体激元的色散特性与填充介质的关系进行了研究.研究表明通过在周期凹槽内填充介质可以有效降低人工表面等离子体激元的渐近频率,并增强金属表面对电磁场的约束.分析了太赫兹波段金属的吸收损耗对人工表面等离子体激元特性的影响,结果显示基于填充介质的浅槽周期表面结构可以获得长距离传输以及场的亚波长约束.通过对波传输的数值仿真,验证了该表面结构在太赫兹波段良好的导波能力.这种表面结构对太赫兹波段新型集成导波器件的设计具有参考价值.     

干涉高斯光诱导的表面等离子激元驻波场的分析

考虑到实际入射光强的空间分布不均匀,基于Kretschmann模型并采用角谱方法分析模拟了两束高斯光干涉诱导表面等离子激元(SPP)驻波场。与理想平面波不同,高斯光诱导的SPP干涉条纹幅值大小不等,分布复杂,这表明光强空间非均匀程度会严重地影响到曝光深度的分布。还分析了金属薄膜的厚度、损耗以及光刻胶的介电常数对SPP驻波场的影响,并得出不恰当的金属板厚和细微损耗都会极大削弱SPP驻波场,而如果光刻胶的介电常数过大则有可能产生不了表面等离子体共振的结论。     

介质填充浅槽周期结构表面上的太赫兹表面等离子体激元

通过在金属表面刻成浅的垂直凹槽,并在槽内填充不同的介质,对金属表面浅槽周期结构上传播的表面等离子体激元的色散特性与填充介质的关系进行了研究.研究表明通过在周期凹槽内填充介质可以有效降低人工表面等离子体激元的渐近频率,并增强金属表面对电磁场的约束.分析了太赫兹波段金属的吸收损耗对人工表面等离子体激元特性的影响,结果显示基于填充介质的浅槽周期表面结构可以获得长距离传输以及场的亚波长约束.通过对波传输的数值仿真,验证了该表面结构在太赫兹波段良好的导波能力.这种表面结构对太赫兹波段新型集成导波器件的设计具有参考价值.     

提高OLED光导出效率的异形金属光栅的设计与优化

提出一种用于有机电致发光器件(OLED)的双面对称矩形金属光栅电极,采用时域有限差分方法(FDTD)模拟研究了OLED中表面等离子体激元的激发和耦合传输的物理规律和物理机制,详细计算和分析了该光栅结构的周期、槽宽、光栅高度、槽底厚度、入射光的入射角与电极透射效率的关系,并由此优化了结构的几何参数,使金属电极的光导出效率相对于通常的金属银层电极增强了1.77倍,为基于表面等离子体激元的高效光导出器件的优化设计提供了理论依据。     

表面等离子激元与F-P共振耦合平衡钙钛矿太阳能电池有源层内载流子产生速率

为提高有机-无机杂化钙钛矿太阳能电池（PSCs）光吸收效率、平衡有源层中载流子产生速率,将周期性纳米光栅结构引入到PSCs器件结构中。分析了光栅周期、光栅高度和有源层厚度对表面等离子激元（SPPs）与法布里-珀罗（F-P）共振耦合模式的影响。通过改变光栅周期,实现了SPPs与F-P共振耦合波长范围与钙钛矿材料的弱吸收光谱区域相重合,同时光栅高度的增加可以增大耦合模式的光谱宽度。SPPs与F-P共振耦合模式实现了金属电极与电子传输层（ETL）界面处的局域电场增强。结果表明:场增强效应扩展到有源区,有效提高了PSCs有源层远入射光侧在570~800 nm波长范围内的光吸收,进而提高了有源层远入射光区域的载流子产生速率。当光栅周期为250 nm、光栅高度为50 nm、源层厚度为300 nm时,PSCs在太阳光弱吸收光谱区域内的本征吸收提高了~12%,有源层远入射光侧载流子产生速率提高了~41%。     

Surface plasmon polaritons frequency-blue shift in low confinement factor excitation region

Surface plasmon polaritons' (SPPs') frequency blue shift is observed in finite-difference time-domain (FDTD) simulation of parallel electron excitation Au bulk structure. Comparing with cold dispersion of SPPs, an obvious frequency blue shift is obtained in low confinement region excitation simulation results. Then, according to SPPs' transverse attenuation characteristics, the excited frequency mode instead of cold dispersion corresponding frequency mode matches it. Thence, this excited mode is confirmed to be SPPs' mode. As is well known the lower the frequency, the smaller the confinement factor is and the lower the excitation efficiency, the wider the bandwidth of excited SPPs is. And considering the attenuation in whole structure, the excited surface field contains attenuation signal. In a low confinement factor region, the higher the SPPs' frequency, the higher the excitation efficiency is, while broadband frequency information obtained in attenuation signal provides high frequency information in stimulation signal. Thence, in the beam-wave interaction, as the signal oscillation time increases, the frequency of the oscillation field gradually increases. Thus, compared with cold dispersion, the frequency of excited SPP is blueshifted This hypothesis is verified by monitoring the time domain signal of excited field in low and high confinement factor regions and comparing them. Then, this frequency-blue shift is confirmed to have commonality of SPPs, which is independent of SPPs' material and structure. Finally, this frequency-blue shift is confirmed in an attenuated total reflection (ATR) experiment. Owing to frequency dependence of most of SPPs' devices, such as coherent enhancement radiation and enhancement transmission devices, the frequency-blue shift presented here is of great influence in the SPPs applications.     

Reflection of Surface Plasmon Polaritons by a Corner Reflector of Negative Index Materials

A novel type of corner reflector for the reflection of surface plasmon polariton (SPP) is proposed. The reflector consists of two layers of compensatory media whose permittivity and permeability take opposite signs to that of the corresponding layer of the SP waveguide. By rigorously solving Maxwell's equations, the reflected SPP is proved to exist. The transverse wave vector of the reflected SPP is always antiparallel to that of the incident SPP and no phase retardation is introduced.     

Numerical investigation of the enhanced unidirectional surface plasmon polaritons generator

A unidirectional surface plasmon polaritons(SPPs) generator with greatly enhanced generation efficiency is proposed. The SPPs generator consists of an asymmetric single nanoslit coated with a polyviny alcohol(PVA) film and a silver rectangle block. The generation efficiency of this SPPs generator is investigated using the finite difference time domain method. Due to the presence of the silver rectangle block, the SPPs generation efficiency of the asymmetric single nanoslit with PVA film can be greatly enhanced and the corresponding wavelength with the maximum enhancement factor can be tuned flexibly. The influence of the structural parameters on the generation efficiency is also investigated for the enhanced unidirectional SPPs generator.     

金属-光折变材料复合全息结构对表面等离激元的波前调控

表面等离激元(surface plasmon polaritons, SPPs)控制具有重要意义.表面电磁波全息法是在金属表面设计能有效控制SPP传输的凹槽阵列结构.本文提出一种新的SPP传输的控制方法,利用金属-光折变材料复合全息结构控制SPP传播.在金属表面覆盖一层光折变材料,两束SPP波在光折变材料内干涉生成全息结构,利用此全息结构能够控制SPP的传播.通过时域有限差分法模拟验证,结果显示,通过金属-光折变材料复合全息结构可以有效地控制SPP波束的传输,实现SPP平面波束的单点聚焦、两点聚焦,以及生成零阶和一阶高斯SPP波束.经过优化发现,光折变材料的最佳厚度为3.3μm,最佳折射率调制度为0.06.现有SPP控制器件主要是通过离子束刻蚀,而金属-光折变材料复合全息结构不需要刻蚀,从而扩展了SPP控制的器件的制作方法,为SPPs的全光控制提供了新的思路,使SPP全光控制成为可能,进一步实现了SPP全光开关等功能.     

基于表面等离激元的偏振态控制光开关

利用四个Au纳米棒组成的类矩形纳米棒四聚体结构设计了一种基于偏振态控制的光开关,并采用有限元法研究了该结构对入射光偏振态的响应特性.研究发现,该结构的透射光谱对入射光的偏振方向具有很强的依赖性,当入射光的偏振角度变化π/2时,其特征峰的开关比分别能达到27.81dB和21.65dB.分析表明,该结构的开关效应主要由不同偏振态下所导致的水平双纳米棒和竖直双纳米棒之间的近场耦合强度不同而实现,该结构透射系数与偏振角度的关系服从Malus law.此外,通过改变类矩形纳米棒阵列结构参数,研究了结构参数对其光开关响应特性的影响.在此基础上,通过改变阵列的周期参数,研究了入射光水平偏振和垂直偏振下周期参数对单元结构透射光谱的影响.该研究结果能够为可调谐双波长偏振光开关的设计提供理论依据.     

测量金属膜粗糙度的表面等离子激元光谱方法

介绍了确定金属膜表面粗糙度的表面等离子激元光谱方法。测量了二种银膜在表面等离子激元激发条件下的光散射强度分布。通过与理论计算的拟合，得到了描写这二种银膜／空气同粗糙界面的特征参数。     

Determination of thickness and optical dispersion property of gold film using spectroscopy of surface plasmon in frequency domain

We propose to use wavelength modulation approach, i.e., the spectroscopy of surface plasmon in frequency domain to characterize the optical dispersion property of gold film. Using this method, we determine the dispersion relationship of gold film in a wavelength range from 537.12 nm to 905.52 nm, and our results accord well with the reported results by other authors. This method is particularly suited for studying the optical dispersion properties of thin metal films, because a series of dielectric constants over a wide spectral range can be determined simultaneously via only a single scan of the incident angle, thereby avoiding the repeated measurements required when using angular modulation approach.