高功率高效率光纤耦合半导体激光模块研制

采用光束整形和空间合束的方法,研制出高功率、高效率多阵列光纤耦合半导体激光模块。将波长为976nm连续工作的5个标准半导体阵列,通过对快轴进行准直和快慢轴光束旋转的方式进行光束整形,准直后进行空间合束,经耦合透镜聚焦,耦合入芯径400μm、数值孔径0.22的光纤。测量结果显示:光纤的出光功率最大可达到327 W,光纤耦合效率大于93.6%。     

28 W环绕式高密度注入波导激光器

报道了一种新型结构形式的环绕式高密度注入波导激光器原理样机。采用环绕式高密度侧面注入技术,利用经过特殊工艺处理的裸增益光纤,当注入泵浦功率320 W时,获得了最高输出功率为28 W的连续激光,斜率效率20%,中心波长1080 nm。结果表明,环绕式高密度注入波导结构形式是可行的,且输出功率和斜率效率具有较大的提升空间。     

Multi-coupler side-pumped Yb-doped double-clad fiber laser

The side-coupler of angle polished method, using angle-polished multimode fiber and optical adhesive, is used to efficiently pump an Yb-doped double-clad fiber laser. The maximum coupling efficiency of 78.6% is achieved by the side-coupler for a multimode fiber with a circular core of 200 μm and a double-clad fiber with a 350/400 μm D-shaped inner cladding. While laser diodes (LDs) with three side-couplers are simultaneously used as pump sources, maximum output power of 1.38 W and slope efficiency of 48.9% are demonstrated in the fiber laser system.     

Quartz CO2 waveguide laser with a separated diffraction grating

A quartz CO₂ waveguide laser with external totally reflecting mirrors and a NaCl plate for the output power coupling is described. The output power was measured as a function of the distance of the mirrors from the waveguide aperture. Using a diffraction grating instead of one of the mirrors the output power at the 10 P(20) line was measured as a function of the mirror position. The results sustain the assumption of a multimode waveguide structure.     

Edge-pumped, folded zig-zag Nd:YAG slab laser

 We report the design and performance of conduction-cooled, edge-pumped, folded zig-zag continuous wave Nd:YAG slab laser. The Nd:YAG slab is pumped with waveguide coupled laser diode bars. The coupling efficiency of waveguide to laser diode radiation is 97%. In a folded zig-zag resonator, a maximum output power of 37 W in multimode operation is achieved for an incident pump power of nearly 180 W on the Nd:YAG slab. This corresponds to an optical-to-optical conversion efficiency of 20% and slope efficiency of 32%. We obtained more than 10 W of output power with the beam quality factors in the width dimension and in the thickness dimension equal to 8.     

Thin Nd:YAG slab laser pumped by lens duct coupled diode laser stacks

High power continuous wave operation of a diode face-pumped thin Nd:YAG slab laser is reported. A novel pumping geometry for a thin Nd:YAG slab using cylindrical lens duct coupled diode laser stacks is demonstrated. In a close-coupled resonator, a maximum laser output power of 260 W in multimode operation is obtained. This corresponds to a slope efficiency of 34% and an optical-to-optical efficiency of 27%, respectively. In high-brightness operation, a polarized laser output of 70 W has been obtained with a beam quality factor close to 4 in both directions. The polarization contrast ratio is >100. PACS 42.55.Xi; 42.60.Pk; 42.60.By     

Tapered fused fiber bundle coupler capable of 1 kW laser combining and 300 W laser splitting

A high efficiency 7 × 1 multimode fiber coupler using the method of fusion and tapering is reported. This coupler can be applied to combine laser power, ad it can be used as a 1 × 7 splitter with reversible simultaneously. In the experiment, for combiner, coupling output power of 1032 W is obtained with the input power of 1066 W. The total coupling efficiency is 96.8%. The average insertion loss of each input fiber is 0.14 dB at ∼150 W input power. To splitter, the sum of 7 output ports power is 294 W with the input power of 341 W, and the insertion loss is about 13.8%. This fiber coupler can be applied in pumping all-fiber double clad fiber laser, as well as power combination and splitting of fiber lasers.     

High-power multi-mode laser to single-mode pump conversion

A novel pump-sharing module for multi-channel amplifiers based on integration of high-power multimode semiconductor lasers and planar waveguide circuits is proposed. The feedback-free modules are designed for optimum coupling, throughput and power uniformity on silicon using BPM method and fabricated via the sol-gel process of photo patternable precursors. Modal properties of the multimode lasers are considered by studying spectrum and spatial distribution of laser output power at different temperatures. Employing an 1500 mW 980 nm multimode laser (TE polarized), via lens and Butt coupling up to 1250 mW of laser output is coupled into the multimode channel waveguides, which are tapered and branched to four single mode waveguides. The measured pump power from splitter outputs, randomly polarized, exceeds 600 mW. At constant temperatures ranging from 22 °C to 30 °C, the pump-sharing modules exhibit good stability with a power uniformity of <0.5 dB over hours.     

Efficiency improvement of multimode Tm3+ doped double cladding silica fiber laser by in-line biconical tapers

Efficiencies improvement of LD (laser diode) pumped multimode large mode area (LMA) Tm³⁺ doped double cladding silica fiber lasers with different in-line biconial tapers were reported. Two types of multimode Tm³⁺ doped fiber were used in this experiment. Each type of fiber was made into three fiber lasers, a uniform geometry fiber laser and two tapered fiber lasers with different taper parameters. Biconical tapers located several centimeters from the output end of the multimode fiber lasers were made by heating and stretching method. Although the threshold of the best tapered fiber laser was added 200 mW, the slope efficiency (25.3%) and the maximum output power (1.31 W) of the fiber laser increased by 10.3% and 350 mW respectively, in comparison with the un-tapered one. Pre and post output laser power ratio was 6.3–15.6. Simultaneously, the laser spectrum moved to shorter wavelengths. The same trends of these characteristics were also observed in the other three tapered fiber lasers.     

Double-clad Tm3+-doped silica fiber laser with Bragg grating inscribed directly into active core by femtosecond laser

We report for the first time to inscribe the Fiber Bragg Grating (FBG) in Tm³⁺-doped multimode double-clad silica fiber by 800 nm femtosecond laser with a phase mask. The 1.35 μm period Bragg grating is written into the fiber core, which is responded to the laser center wavelength located at nearly 1960 nm. Continuous wave total output power of 11.5 W is obtained under the launched pump power of 29.8 W, corresponding to a slope efficiency of 45.0% and a conversion efficiency of 38.6%.     

大模场面积光纤激光器79.4 W单横模输出

 采用光纤缠绕方法,对国产大模场面积多模光纤激光器缠绕前后的输出性能进行了对比研究。将光纤激光器输出端在半径为65 mm的圆筒上缠绕两圈后,获得了单横模输出。光纤缠绕前后,激光器的光束质量因子由1.24减小为1.06,斜率效率由64.7％减小为54.3％。当泵浦功率为149 W时,缠绕前后的输出功率分别为94.7 W和79.4 W。虽然缠绕后功率有所减小,但激光亮度增加了15％。同时对实验所用光纤的缠绕损耗进行了理论计算,实验结果与理论计算值符合得较好。     

Compact TEM<Subscript>00</Subscript> grazing-incidence Nd:GdVO<Subscript>4</Subscript> laser using a folded cavity

A compact diode-side-pumped Nd:GdVO₄ laser system using a folded cavity and grazing-incidence configuration is presented. The highest multimode output power obtained was 21.8 W at 36 W of effective diode pump power. Highest optical-to-optical conversion efficiency of 61.5% was achieved at 33 W of effective diode pump power with 20.3 W of multimode output power. For single-mode TEM₀₀ operation, an intracavity telescope was adopted for mode matching in the horizontal direction. Because of the folded cavity and the intracavity telescope, this laser head was the most compact to our knowledge of the TEM₀₀ grazing-incidence laser geometry. At last, an output power of 15 W was produced at 36 W of effective diode pump power. The stable Q-switching operation was also obtained. PACS 42.55.-f; 42.55.Xi; 42.60.Gd     

Experimental study of a high power and high efficiency CW diode-side-pumped Nd:YAG laser

This paper reports on the characterization of a diode-side-pumped CW Nd:YAG laser. A side-pumped configuration with 9 laser diodes is used for the laser. Pump light is directly coupled into the Nd:YAG rod without focusing lenses and the pump light distribution in the Nd:YAG rod was calculated. A maximum output power of 150 W in multimode operation is obtained for a pumping power of 400 W. The optical–optical efficiency is 37%. Output power of the laser under different output couplers, resonator lengths and temperatures of the cooling water have been studied.     

High power continuous-wave diode-laser-pumped Nd:YAG laser

We report on a diode-laser-pumped cw Nd: YAG laser operating at a power level of 150 W. By using a transverse pump geometry, the radiation of 54 diode lasers with an output power of 10 W each is coupled into a Nd:YAG rod. In multimode operation, an optical slope efficiency of 32% and an optical to optical efficiency of 29% are obtained. In TEM₀₀ operation, an output power of more than 30 W is realized with an optical to optical efficiency of 10%.     

Diode-pumped Nd:YAG laser using reflective pump optics

We have examined the performance of a diode-laser side-pumped Nd:YAG laser using elliptical mirrors to focus the output of 6 × 10 W laser-diode arrays into the Nd: YAG rod. The multimode cw output power was 14 W with an optical to optical efficiency of 29%. With a resonator designed for TEM₀₀ mode operation 12 W of output was achieved.     

基于光束填充的多单管半导体激光器光纤耦合

为了进一步提高多单管半导体激光器的输出功率,通过对常见的阶梯型多单管半导体阵列进行分析,提出在光斑尺寸较小的慢轴方向对光束进行填充,在同样的耦合条件下,使更多的激光能量耦合进光纤中,实现更高功率的输出。文中使用光参数积作为评价光束质量的指标,论证了慢轴光束填充的可行性,利用ZEMAX仿真软件对8路常见阶梯型多单管半导体阵列和12路填充阵列进行对比仿真,在不影响耦合效率的前提下,实现了将12路波长为860 nm、输出功率3 W的单管半导体激光器耦合进芯径105 μm、数值孔径0.22的光纤中,光纤输出功率为33.4 W,光纤耦合效率为92.78%。仿真结果表明,对慢轴方向进行光束填充可以在一定程度上提高多单管半导体激光的功率输出。     

Yb:CaGdAlO4 thin-disk laser

We present the first demonstration of a Yb:CALGO thin-disk laser. In a slightly multimode configuration, we obtained up to 30?W of average power at a slope efficiency of 40% and an optical-to-optical efficiency of 32%. With a single-mode cavity, an average power of 25?W was achieved. A tuning range from 1018 to 1052?nm could be demonstrated by inserting a prism into the cavity. In the Q-switched regime, we obtained 1?mJ of pulse energy at a repetition rate of 100?Hz.     

High-power continuous-wave cladding-pumped Raman fiber laser

We demonstrate a high-power single-mode cladding-pumped Raman fiber laser. The Raman fiber laser consists of a 1.2 km long germanium-doped double-clad fiber in a linear cavity, which is spliced to a single-mode fiber. The laser is end pumped by a multimode erbium-ytterbium-doped fiber, which is coupled to the inner cladding of the Raman fiber. The embedded core was designed to be single mode at the Raman Stokes wavelength, and up to 10 W of power was obtained at 1660 nm from the single-mode fiber end. The laser has a slope efficiency of 67% and a threshold of 6.5 W.     

High-peak-power tunable laser operation of Yb:SrF2

Growth, spectroscopic properties, and laser performance of Yb:SrF(2) crystals have been investigated. In spatial multimode operation of a diode-pumped Yb:SrF(2) laser a slope efficiency of 46% was measured. 180W output power with high beam quality at a pulse duration of 1.5ms was achieved by installing a mode cleaning aperture. A maximum average output power of 270mW and a tuning range of 73nm was observed.     

High efficiency TEM00 mode, diode-pumped, conduction-cooled, Nd:YAG zig-zag slab laser

We report a compact, conduction-cooled, highly efficient, continuous wave (CW) Nd:YAG slab laser in diode-side-pumped geometry. To achieve high efficiency, a novel laser head for Nd:YAG slab has been developed. For an absorbed pump power of 27.6 W, maximum output power of 10.4 W in multimode and 8.2 W in near-diffraction-limited beam quality has been obtained. Slope and optical-to-optical conversion efficiencies are 45.3% and 37.7% in multimode with beam quality factors (M²) in x and y directions equal to 32 and 8, respectively. TEM₀₀ mode operation was achieved in a hybrid resonator with slope and optical-to-optical conversion efficiencies of 43.2% and 29.7%, respectively. Beam quality factors in x and y directions are ?1.5 and ?1.6 for the whole output power range. The laser radiation was linearly polarized and polarization contrast ratios are >1200:1 in the multimode and 1800:1 in the TEM₀₀ mode operation. In passive Q-switching with Cr⁴⁺:YAG crystal of 68% initial transmission, 18 ns pulsewidth has been achieved with an average power of 2 W at a repetition rate of 16 kHz.