Ho3+/Yb3+共掺ZnO-Al2O3-GeO2-SiO2玻璃陶瓷的制备和上转换发光性质

综合ZnO-Al₂O₃-SiO₂系和锗酸盐玻璃陶瓷的优点,采用熔融-晶化法首次制备了Ho³⁺/Yb³⁺共掺以ZnAl₂O₄为主晶相的ZnO-Al₂O₃-GeO₂-SiO₂系玻璃陶瓷。因[GeO₄]四面体和[SiO₄]四面体都是玻璃网络形成体,讨论了GeO₂取代SiO₂对玻璃陶瓷样品硬度及发光性能的影响,最终确定GeO₂的取代量为10.55%（w/w）时,玻璃陶瓷综合性能最佳。在980 nm泵浦光的激发下,发现强的绿色（546 nm）和弱的红色（650 nm）上转换发光,并研究了不同Ho³⁺/Yb³⁺掺杂比对样品上转换发光的影响,最终结果表明当Ho³⁺/Yb³⁺掺杂比为1：11（n/n）时样品荧光强度最强,在绿色上转换发光材料方面具有潜在的应用。     

Hydrothermal Synthesis and Up‐conversion Luminescence of Ho3+/Yb3+ Co‐doped PbTiO3

Ho³⁺/Yb³⁺ co‐doped PbTiO₃ nanocrystals with different content of dopant were successfully prepared via a facile hydrothermal method. The purity, morphology, element distribution, chemical state and up‐conversion (UC) photoluminescence (PL) of PbTiO₃ nanocrystals affected by Ho³⁺ dopant are investigated systematically. X‐ray diffraction (XRD) results illustrate that PbTiO₃ samples with the doping Ho³⁺ concentration ranging from 0 to 5 mol‐% are perovskite structure. The doping Ho³⁺ ions have no change on the crystal structure of perovskite PbTiO₃. Owing to the non‐equivalent substitution of Ho³⁺ to Ti⁴⁺ in PbTiO₃, the particle size of Ho³⁺/Yb³⁺ co‐doped PbTiO₃ samples is decreased as well as the particle agglomeration is detected. Moreover, Ho and Yb ions have uniform distributions in the PbTiO₃ nanoparticles as the presence of Ho³⁺ and Yb³⁺ cations. The up‐conversion spectra demonstrate that Ho/Yb co‐doped PbTiO₃ samples have up‐conversion emissions centered at 550 nm, 660 nm and 755 nm, corresponding to the transitions of ⁵F₄(⁵S₂)→⁵I₈, ⁵F₅→⁵I₈ and ⁵S₂(⁵F₄)→⁵I₇ of Ho³⁺ ions. Additionally, the effect of temperature on the UC PL property of Ho³⁺/Yb³⁺ co‐doped PbTiO₃ system is further investigated. The sensitivity and the trend of Ho³⁺/Yb³⁺ co‐doped PbTiO₃ samples in temperature from 298 k to 493K are calculated on the basis of fluorescence intensity ratio (FIR) method. Ho³⁺/Yb³⁺ co‐doped PbTiO₃ nanocrystals are verified the high potential in the optical temperature sensing.     

Effect of Europium Ion Concentrations on the Photoluminescence Emission of Nano-Crystalline BaTiO<Subscript>3</Subscript> Prepared by Sol–Gel Technique

Nano-crystalline. ferroelectric Eu³⁺: BaTiO₃ powders and thin films have been prepared using (Ba(Ac)₂), and titanium butoxide (Ti(C₄H₉O)₄), as precursors. The thin films were prepared by spin coating using the sol–gel method. The evolution of the network bonds and the structural characterization of the prepared samples was studied by Fourier Transform Infrared Spectrometer (FTIR) and X-ray diffraction (XRD) techniques, respectively. The as-grown thin films and powders were found to be amorphous, and crystallized to the tetragonal phase after annealing at 750^∘C in air for 30 min. The crystallite size of the doped sample with 4% Eu³⁺ ions in the form of thin film and powder was found to be equal to = 21 and 32 nm, respectively.The photoluminescence of nano-crystalline powders and thin films at 488 nm were reported. The luminescence spectra of ultra fine Eu³⁺: BaTiO₃ powders and thin films are dominated by the ⁵D₀ → ⁷F_j (j = 0−4) transitions, suggesting a strong distortion of the Eu³⁺ sites. The disorder contributes, together with the presence of numerous charge compensation mechanisms, to the strong inhomogeneous broadening of the ⁵D₀ → ⁷F_j luminescence band of the Eu³⁺.     

Photoacoustic spectroscopic studies of Ho3+, Er3+, and Sm3+ doped polyvinyl alcohol films

Photoacoustic (PA) spectra of Ho³⁺, Er³⁺, and Sm³⁺ doped PVA films were obtained in 350–800 nm range. PA spectra were also obtained for the respective dopant oxides: Ho₂O₃, Er₂O₃, and Sm₂O₃ for comparison. It was found that in PVA the PA sensitivity has increased considerably compared to pure rare earth oxides. The relative intensities of absorption bands at 540 and 637 nm of Ho₃₊: PVA have shown distinct enhancement, indicating the increase in nonradiative relaxation at these excitations. Furthermore, the PA signals at wavelengths for different PA absorption bands were monitored as a function of chopping frequency. These experiments have shown that PA signal varies w⁻¹ both for oxides and PVA samples, suggesting that they behave as thermally thin samples. © 1997 John Wiley & Sons, Inc.     

Ho3+/Yb3+共掺ZnO-Al2O3-GeO2-SiO2玻璃陶瓷的制备和上转换发光性质

综合ZnO-Al_2O_3-SiO_2系和锗酸盐玻璃陶瓷的优点,采用熔融-晶化法首次制备了Ho~(3+)/Yb~(3+)共掺以ZnAl_2O_4为主晶相的ZnO-Al_2O_3-GeO_2-SiO_2系玻璃陶瓷。因[GeO_4]四面体和[SiO_4]四面体都是玻璃网络形成体,讨论了GeO_2取代SiO_2对玻璃陶瓷样品硬度及发光性能的影响,最终确定GeO_2的取代量为10.55%(w/w)时,玻璃陶瓷综合性能最佳。在980 nm泵浦光的激发下,发现强的绿色(546 nm)和弱的红色(650 nm)上转换发光,并研究了不同Ho~(3+)/Yb~(3+)掺杂比对样品上转换发光的影响,最终结果表明当Ho~(3+)/Yb~(3+)掺杂比为1∶11(n/n)时样品荧光强度最强,在绿色上转换发光材料方面具有潜在的应用。     

Influence of Rare Earth Ho3+ Doping on Structural,Microstructure and Magnetic Properties of ZnO Bulk and Thin Film Systems

We have investigated the doping behavior of rare earth element holmium (Ho³⁺) in ZnO semiconductor. The structural, microstructure, and magnetic properties of Zn_1-xHo_xO (x=0.0, 0.04, and 0.05) thin films deposited on Si(100) substrate by thermal evaporation technique were studied. The ceramic targets were prepared by conventional solid state ceramic technique. The pallets used as target were final sintered at 900 oC in the presence of N2 atmosphere. The experimental results of X-ray diffraction (XRD) spectra, surface morphology, and magnetic properties show that the Ho³⁺ doped ZnO thin films has a strong influence on the materials properties. The higher angle shift in peak position and most preferred (101) orientation were observed in XRD pattern. These spectra confirmed the substitution of Ho3+ in ZnO lattice. The surface morphology and stoichiometry for both bulk and thin films were analyzed by scanning electron microscopy and energy dispersive spectroscopy. It was observed that grain size decreases with the increase of Ho³⁺. Room temperature ferromagnetism was observed for Zn_0.95Ho_0.05O films. The ferromagnetism might be attributed to the substitution of Ho ions for Zn²⁺ in ZnO lattices.     

Detection of up-conversion in nano-structure BaTiO<Subscript>3</Subscript> co-doped with Er<Superscript>3+</Superscript> and Yb<Superscript>3+</Superscript> ions

Nano-structure pure barium titanate BaTiO₃ (BT) and (BT) co-doped with constant concentration of Er³⁺ ions and different concentrations of Yb³⁺ ions were prepared using sol–gel method. XRD results confirmed that the pure sample was found to crystallize in tetragonal phase by sintering at 750 °C for 1 h. All major peaks corresponding to perovskite BT phase appeared. Efficient infrared-to-visible up-conversion is reported in the doped samples. The conversion process and results in the generation of visible emissions are discussed. Up-conversion efficiency for red emission predominates in doped samples. Results illustrate the large potential of this class of materials for photonic applications in optoelectronics devices.     

Sol-Gel Processing and Luminescent Properties of Rare-Earth Oxyfluoride Materials

Luminescent rare-earth oxyfluoride materials were prepared by a sol-gel method using trifluoroacetic acid as a fluorine source. Crystalline (La, Eu)OF powders and thin films were obtained by heating gels at typically 600–800°C. Transparent SiO₂-LaOF glass-ceramic thin films were also prepared by mixing the trifluoroacetate sols and silica sols, spin-coating on silica glass substrates and heating at temperatures 600–900°C. Eu³⁺ ions doped in the oxyfluoride materials exhibited a strong red ⁵D₀ ⁷F₂ emission (611 nm) by a charge-transfer (O^2–-Eu³⁺) excitation with ultra-violet radiation (265 nm). It was strongly suggested that the Eu³⁺ activators were preferentially incorporated into the crystalline LaOF phase in the SiO₂-LaOF glass-ceramics.     

Two color up-conversion emissions of Er<Superscript>3+</Superscript>-doped Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanopowders prepared by non-aqueous sol-gel method

Er³⁺-doped Al₂O₃ nanopowders have been prepared by the non-aqueous sol-gel method using the aluminum isopropoxide as precursor, acetylacetone as a chelating agent, nitric acid as a catalyzer, and hydrated erbium nitrate as a dopant under isopropanol environment. The different phase structure, including three crystalline types of (Al, Er)₂O₃ phases, α, γ, θ, and an Er–Al–O stoichiometric compound phase, Al₁₀Er₆O₂₄, was observed for the 0.01–0.5 mol% Er³⁺-doped Al₂O₃ nanopowders at the sintering temperature of 1,000 °C. The green and red up-conversion emissions centered at about 523, 545 and 660 nm, corresponding respectively to the ²H_11/2, ⁴S_3/2→⁴I_15/2 and ⁴F_9/2→⁴I_15/2 transitions of Er³⁺, were detected by a 978 nm semiconductor laser diodes excitation. With increasing Er³⁺ doping concentration from 0.01 to 0.1 mol%, the intensity of the green and red emissions increased with a decrease of the intensity ratio of the green to red emission. When the Er³⁺ doping concentration rose to 5 mol%, the intensity of the green and red emissions decreased with an increase of their intensity ratio. The maximum intensity of both the green and red emissions with the minimum of intensity ratio was obtained, respectively, for the 0.1 mol% Er³⁺-doped Al₂O₃ nanopowders composed of a single α-(Al,Er)₂O₃ phase. The intensity ratio of the green emission at 523 and 545 nm increased monotonously for all Er³⁺ doping concentrations. The two-photon absorption up-conversion process was involved in the green and red up-conversion emissions of the Er³⁺-doped Al₂O₃ nanopowders.     

不同掺杂浓度Tm3+：LiLuF4单晶的1800 nm荧光发射

采用坩埚下降法生长了Tm³⁺掺杂浓度为0.45%,0.90%,1.63%与3.25%（摩尔分数,x）的LiLuF₄单晶.测试了样品的电感耦合等离子体原子发射光谱（ICP-AES）、X射线衍射（XRD）谱、吸收光谱（1400-2000 nm）,并且分析比较了808 nm半导体激光器（LD）激发下荧光光谱. 结果表明：当Tm³⁺的浓度从0.45%变化到3.25%时,1800 nm处的荧光强度呈现了先增后减的趋势,当掺杂浓度约为0.90%时达到最大值,而位于1470 nm处的荧光强度则呈现了相反的趋势. Tm³⁺：³F₄能级的荧光衰减寿命随着掺杂浓度的增加不断减小. 1800 nm处的这种荧光强度变化归结于Tm³⁺离子间的交叉驰豫效应（³H₆,³H₄→³F₄,³F₄）和自身的浓度猝灭效应. 同时计算得到了浓度为0.90%的样品在1890 nm处的最大发射截面为0.392×10^-20 cm². 并且根据Judd-Ofelt 理论所得寿命和测定的荧光寿命计算得到了³F₄→³H₆的最大量子效率约为120%.     

Enhancement of the Up-conversion Luminescence of 12CaO · 7Al2O3:Tm3+/Yb3+ Doped with Alkaline Earth Metal Ions

12CaO?·?7Al₂O₃ doped with lanthanide is characterized by remarkable and technologically important up-conversion emission. However, the low up-conversion efficiency still remains the main limitation for practical applications. To improve the efficiency, bivalent alkaline earth ions (Mg²⁺, Sr²⁺, Ba²⁺)-tridoped Tm³⁺/Yb³⁺/12CaO?·?7Al₂O₃ were synthesized through a high-temperature solid-state reaction. The up-conversion luminescence properties of the samples were investigated by X-ray diffraction, fluorescence spectral measurement pump power, and fluorescence decay curves. The luminescence intensity of samples was significantly enhanced by bivalent alkaline earth ions. 12CaO?·?7Al₂O₃ doped with Sr²⁺ ions has stronger effects on up-conversion enhancement, which is better than Mg²⁺ and Ba²⁺. The up-conversion emission intensity was enhanced by 318 times and the red emission intensity by 218 times with 10?mol% Sr²⁺ ion. Additionally, the blue and red up-conversion emission peaks at 475 and 650?nm corresponding to energy transitions of ¹G₄ → ³H₆ and ¹G₄ → ³F₄, ³F₂ → ³H₆ were characterized using steady-state rate equations.     

The influence of polyvinylpyrrolidone on thick and optical properties of BaTiO<Subscript>3</Subscript>:Er<Superscript>3+</Superscript> thin films prepared by sol–gel method

Erbium (Er³⁺) 0.5% mol doped barium titanate (BaTiO₃) thin films were elaborated via sol–gel method and dip-coating technique using titanium alkoxide and barium pentanedionate. Two syntheses were performed [with and without polyvinylpyrrolidone (PVP)] in order to obtain thick films. The BaTiO₃:Er³⁺ thin films prepared from the sol with PVP were elaborated with 1 layer and those without PVP and were elaborated with 17 layers. In both cases, the films were deposited on silica quartz substrates. Both BaTiO₃:Er³⁺ films presented a cubic phase, as determined by X-ray diffraction. BaTiO₃:Er³⁺ films elaborated with PVP via single-step dip coating produced crack-free films with thicknesses of ~800 nm. SEM micrographs for the obtained BaTiO₃:Er³⁺ films revealed high homogeneity and density. Mapping images obtained from BaTiO₃:Er³⁺ revealed homogeneous distribution of Er³⁺ ions on the surface. XPS analyses of the chemical state and chemical environment of the constituent elements in the compositions showed that Er³⁺ ions in (Ba_1−x Er _x )TiO₃ are in mixed valence of Er³⁺/Er²⁺. The BaTiO₃:Er³⁺-PVP film exhibited luminescent properties under near-infrared excitation, as revealed by green emissions. The BaTiO₃:Er³⁺-PVP film has good potential for optical applications.     

Spectroscopic Properties and Upconversion Studies in Ho3+/Yb3+ Co‐doped Calcium Scandate with Spectrally Pure Green emission

The optical properties of a Ho³⁺/Yb³⁺ co‐doped CaSc₂O₄ oxide material are investigated in detail. The spectral properties are described as a function of doping concentrations. The efficient Yb³⁺→Ho³⁺ energy transfer is observed. The transfer efficiency approaches 50 % before concentration quenching. The concentration‐optimized sample exhibits a strong green emission accompanied with a weak red emission, showing perfect green monochromaticity. The results of the spectral distribution, power dependence, and lifetime measurements are presented. The green, red, and near‐infrared (NIR) emissions around 545, 660, and 759 nm are assigned to the ⁵F₄+⁵S₂→⁵I₈, ⁵F₅→⁵I₈, and ⁵F₄+⁵S₂→⁵I₇ transitions of Ho³⁺, respectively. The detailed study reveals the upconversion luminescence mechanism involved in a novel Ho³⁺/Yb³⁺ co‐doped CaSc₂O₄ oxide material.     

钙钛矿结构荧光材料MZrO3:Eu3+,A (M=Ca2+, Ba2+; A=Li+, Na+, K+)的制备及其发光性质

Calcium and barium zirconate powders based upon CaZrO₃:Eu³⁺,A and BaZrO₃:Eu³⁺,A (A=Li⁺, Na⁺, K⁺) were prepared by combustion synthesis method and heating to ~1000℃ to improve crystallinity.The structure and morphology of materials were examined by X-ray diffraction (XRD) and scanningelectron microscopy (SEM). XRD results showed that CaZrO₃:Eu³⁺,A and BaZrO₃:Eu³⁺,A (A=Li⁺, Na⁺, K⁺) perovskites possessed orthorhombic and cubic structures, respectively. The morphologies of all powderswere very similar consisting of small, coagulated, cubical particles with narrow size distributions andsmooth and regular surfaces. The characteristic luminescences of Eu³⁺ ions in CaZrO₃:Eu³⁺,A (A=Li⁺, Na⁺, K⁺) lattices were present with strong emissions at 614 and 625 nm for ⁵D₀→⁷F₂ transitions with other weakeremissions observed at 575, 592, 655, and 701 nm corresponding to ⁵D₀→⁷F_n transitions (where n=0, 1, 3, 4 respectively). In BaZrO₃:Eu³⁺ both the ⁵D₀→⁷F₁ and ⁵D₀→⁷F₂ transitions at 595 and 613 nm were strong.Photoluminescence intensities of CaZrO₃:Eu³⁺ samples were higher than those of BaZrO₃:Eu³⁺ lattices. Thisremarkable increase of photoluminescence intensity (corresponding to ⁵D₀→⁷F_n transitions) was observedin CaZrO₃:Eu³⁺ and BaZrO₃:Eu³⁺ if co-doped with Li⁺ ions. An additional broad band composed of manypeaks between 440 to 575 nm was observed in BaZrO₃:Eu³⁺,,A samples. The intensity of this band wasgreatest in Li⁺ co-doped samples and lowest for K⁺ doped samples.     

Preparation and up-conversion fluorescence of rare earth (Er or Yb/Er)-doped TiO2 nanobelts

Anatase TiO₂ nanobelts doped with rare earth (RE) ions Yb³⁺, Er³⁺ or Yb³⁺/Er³⁺ have been prepared using layered titanate nanobelts (LTO NBs) with RE ions as the precursor obtained by ion-exchange between LTO NBs and RE ions under hydrothermal process. Various measurement results demonstrate that the RE ions have doped into the lattice of TiO₂, and the Er³⁺ or Yb³⁺/Er³⁺ doped nanobelts show strong visible up-conversion (UC) fluorescence under 980 nm excitation. The UC emission intensity of LTO NBs embedded with Er³⁺ or Yb³⁺/Er³⁺ is slightly higher than that of the corresponding TiO₂ nanobelts doped with RE ions, whereas higher RE doping content leads to the decrease of UC emission intensity due to the concentration-quenching effect.     

Green up-conversion emission in Er3+:BaTiO3 sol-gel powders

Bright green emissions at 549 and 526 nm have been observed from sol-gel derived Er3+:BaTiO3 powders upon excitations at two near infrared (NIR) wavelengths of 973 and 816 nm. The decay characteristics were measured and studied. It was found that the predominant emission at 549 nm has very different lifetimes upon excitation at 973 and 816 nm, which was explained by the mechanisms of excited state absorption (ESA) of individual Er3+ ion and cooperative energy transfer (CET) between two near Er3+ ions for the up-conversion emission. Analysis also showed that 973-nm excitation is more effective for the green up-conversion emission.     

LiYF4晶体中Ho3+离子真空紫外吸收光谱的理论解析

运用配位场理论方法获得了Ho3+离子低自旋4f95d组态的谱项和J-光谱多重态,根据电偶极跃迁选律合理地解析了LiYF4晶体中Ho3+离子在真空紫外区(120～160 nm)的吸收光谱,4个主要的吸收峰分别被归属为从基态(5I8)到Ho3+离子的低自旋4f95d组态的自旋允许跃迁。     

Investigation of Structural and Luminescent Properties of Sol-Gel-Derived Cr‑Substituted Mg3Al1−xCrx Layered Double Hydroxides

In the present work, Cr-substituted Mg₃Al_1−xCr_x layered double hydroxides (LDHs) were synthesised through the phase conversion of sol-gel-derived mixed-metal oxides in an aqueous medium. The chromium substitution level in the range of 1 to 25 mol% was investigated. It was demonstrated that all synthesised specimens were single-phase LDHs. The results of elemental analysis confirmed that the suggested synthetic sol-gel chemistry approach is suitable for the preparation of LDHs with a highly controllable chemical composition. The surface microstructure of sol-gel-derived Mg₃Al_1−xCr_x LDHs does not depend on the chromium substitution level. The formation of plate-like agglomerated particles, which consist of hexagonally shaped nanocrystallites varying in size from approximately 200 to 300 nm, was observed. Optical properties of the synthesised Mg₃Al_1−xCr_x LDHs were investigated by means of photoluminescence. All Cr-containing powders exhibited characteristic emission in the red region of the visible spectrum. The strongest emission was observed for the sample doped with 5 mol% Cr³⁺ ions. However, the emission intensity of samples doped with 1–10 mol% Cr³⁺ ions was relatively similar. A further increase in the Cr³⁺ ion concentration to 25 mol% resulted in severe concentration quenching.     

A sol-gel route for the development of rare-earth aluminum borate nanopowders and transparent thin films

A new sol-gel route was applied to obtain Y_0.9Er_0.1Al₃(BO₃)₄ crystalline powders and amorphous thin films by using Al(acac)₃, B(OPrⁱ)₃, Y(NO₃)₃·6H₂O, and Er(NO₃)₃·5H₂O as starting materials dissolved in propionic acid and ethyl alcohol mixtures. Our study shows that propionic acid acts as good chelant agent for yttrium and erbium ions while ethyl alcohol allows to dissolve Al(acac)₃. This process makes the resulting sols very stable to obtain homogeneous gels and transparent amorphous thin films. In addition, the propionic acid prevents the sol precipitation, making easy porous- and crack-free thin film depositions. Chemical reactions involved in the complexation were discussed. As-prepared powders and films are amorphous and present a good thermal stability due to their high glass transition (746 °C) and crystallization temperatures (830 °C). This new sol-gel route showed to be adequate to obtain dense and crack-free thin films free of organic and hydroxyl groups that can be considered as promising materials to be used in integrated optical systems.     

Upconversion Luminescence from Ho3+ and Yb3+ Codoped α-NaYF4 Single Crystals

The Ho³⁺/Yb³⁺ co-doped α-NaYF₄ single crystal was grown successfully for the first time by a modified Bridgman method in which KF was used as assisting flux and a large temperature gradient (70-90 oC/cm) of solid-liquid interface was adopted. Upconversion emissions at green ～544 nm, red ～657 and ～751 nm were obtained under 980 nm laser diode excitation. The intensity at ～544 nm was much stronger than those of ～657 and ～751 nm. The mechanisms of the upconversion emissions were investigated by studying the relationship between the upconversion intensity and pump power. The optimized Yb³⁺ concentration was about 8.08 mol% when Ho³⁺ concentration was hold at about 1.0 mol%. The results showed that Ho³⁺/Yb³⁺+ doped α-NaYF₄ single crystal was a possible candidate upconversion material for the green solid-state laser.