Direct dimethyl ether synthesis over mesoporous Cu–Al2O3 catalyst via CO hydrogenation

Research on Chemical Intermediates - Syngas conversion to dimethyl ether (DME) is an important reaction (STD) in C1 chemistry since DME not only possesses high value but also can be used as a vital...     

Modelling (vapour + liquid) and (vapour + liquid + liquid) equilibria of {water (H2O) + methanol (MeOH) + dimethyl ether (DME) + carbon dioxide (CO2)} quaternary system using the Peng–Robinson EoS with Wong–Sandler mixing rule

The (vapour + liquid) equilibria (VLE) and (vapour + liquid + liquid) equilibria (VLLE) binary data from literature were correlated using the Peng–Robinson (PR) equation of state (EoS) with the Wong–Sandler mixing rule (WS). Two group contribution activity models were used in the PRWS: UNIFAC–PSRK and UNIFAC–Lby. The systems were successfully extrapolated from the binary systems to ternary and quaternary systems. Results indicate that the PRWS–UNIFAC–PSRK generally displays a better performance than the PRWS–UNIFAC–Lby.     

Adaptation o Cu／ZnO／Al2O3 to Temperature Change in Methanol Synthesis from CO2 Hydrogenation

The induction behavior in CO2 hydrogenation was studied by varying the reaction temperature to investigate the adaptation of the Cu/ZnO/Al2O3 catalyst to the temperature change,The results indicated that a used catalyst had a tendency to keep the last running state in new reaction conditions for MeOH formation,and that this tendency was related to the difference in Cu/Cu^n ration caused by CO2 and CO produced at different reaction temperatures,However,the reverse water-gas shift reaction (BWGS) induced at four temperatures was completely different from that of methanol synthesis,It implied that the two so-called competitive reactions in CO2 H2,RWGS and methanol synthesis,have different, active centers.     

Effect of gamma-irradiation on surface and catalytic properties of CuO−ZnO/Al2O3 system

A copper, zinc and aluminium mixed oxides sample having the nominal composition 0.25 CuO/0.03 ZnO/Al₂O₃ was prepared by impregnating Al(OH)₃ with copper and zinc nitrate solutions, drying at 100 °C then heating in air at 600 °C. The obtained solid was exposed to different doses of -rays (20–160 Mrad). The surface characteristics namelyS _BETV_P andr of different treated adsorbents were determined from N₂ adsorption isothems measured at –196 °C. The catalytic activity of various irradiated solids was determined by following up the kinetics of CO-oxidation by O₂ at 150–200 °C. The results showed that the doses up to 80 Mrad resulted in no significant change in theS _BET but increased slightly theV _P (20%) of the treated adsorbents. The irradiation at 160 Mrad caused an increase of 20% in theS _BET of the irradiated solid sample. The catalytic activity increased progressively by increasing the dose, a dose of 160 Mrad brought about an increase of 140% in the catalyst's activity. The apparent activation energy of the catalytic reaction decreased monotonically by increasing the absorbed dose of -rays which was attributed to a parallel induced decrease in the value of pre-exponential term of the Arrhenius equation. The observed increase in the catalytic activity due to -irradiation has been interpreted as a result of increasing the concentration of catalytically-active sites contributing in chemisorption and catalysis of CO-oxidation via a possible fragmentation of CuO crystallites.     

Al2O3 Effect on the Catalytic Activity of Cu-ZnO-Al2O3-SiO2 Catalysts for Dimethyl Ether Synthesis from CO2 Hydrogenation

The effect of Al2O3 on the Cu-ZnO-Al2O3-SiO2 catalysts prepared by a pseudo sol-gel method has been investigated and these catalysts were characterized by XRD, H2-TPR, XPS, NH3-TPD and CO2- TPD techniques. As revealed by XRD and H2-TPR, the added alumina produces high dispersion of CuO and makes the reduction of CuO difficult. XPS analysis detects a remarkably high Al^3＋ enrichment at the surface of calcined samples, along with a decrease of Eb of Cu 2p3/2, which confirms the Cu-Al interaction. Another important role of Al203 would be to incorporate into the SiO2 structure to form the acid-base sites for ether formation. The reaction results shows that the addition of Al2O3 exhibits a promoting effect on the CO2 conversion only when its content is below 1.4%, and an optimal DME selectivity is obtained when 4.0%Al2O3 is added, indicating a better ＇synergistic effect＇ is present between the methanol forming component and the acidic component in bifunctional catalysts. Possible relationship between the catalytic activity and the Cu-Al interaction as well as the surface acidity is discussed.     

Effect of ZnO on the interfacial bonding between Na2O–B2O3–SiO2 vitrified bond and diamond

Diamond composites were prepared by sintering diamond grains with low melting Na₂O–B₂O₃–SiO₂ vitrified bonds in air. The influence of ZnO on the wettability and flowing ability of Na₂O–B₂O₃–SiO₂ vitrified bonds was characterized by wetting angle, the interfacial bonding states between diamond grains and the vitrified bonds were observed by scanning electron microscope (SEM), and the micro-scale bonding mechanism in the interfaces was investigated by means of energy-dispersive spectrometer (EDS), Fourier transform infrared (FTIR) spectrometer and X-ray photoelectron spectroscopy (XPS). The experimental results showed that ZnO facilitated the dissociation of boron/silicon–oxygen polyhedra and the formation of larger amount of non-bridging oxygen in the glass network, which resulted in the increase of the vitrified bonds' wettability and the formation of –CO, –O–H and –C–H bonds on the surface of diamond grains. B and Si diffused from the vitrified bonds to the interface, and C–C, C–O, CO and C–B bond formed on the surface of sintered diamond grains during sintering process, by which the interfacial bonding between diamond grains and the vitrified bonds was strengthened.     

Effect of zinc oxide on microhardness and sintering behavior of MgO–Al2O3–SiO2 glass–ceramic system

Glass–ceramic in the MgO–Al₂O₃–SiO₂ system with crystallization ability of gahnite (ZnO·Al₂O₃) and mullite were synthesized. It was found that the glass–ceramic containing gahnite phase had desirable mechanical behavior and reached to an acceptable hardness and density. The compositions were designed based on magnesium oxide replacement (from MgO–Al₂O₃–SiO₂ glass–ceramic system) with zinc oxide. Glass–ceramics were characterized by DTA, X-ray diffraction and scanning electron microscopy. Heat treatment at 1100 °C cause form gahnite crystals in glass–ceramic. Microhardness increased with increasing gahnite crystals. To achieve good mechanical properties, the initially formed high gahnite phase must transform.     

(Solid + liquid) equilibria for the ternary system (CsBr + LnBr3 + H2O) (Ln = Pr,Nd, Sm) at T = 298.2 K and atmospheric pressure,thermal and fluorescent properties of Cs2LnBr5·10H2O

The (solid + liquid) phase equilibria of the ternary systems (CsBr + LnBr₃ + H₂O) (Ln = Pr, Nd, Sm) at T = 298.2 K were studied by the isothermal solubility method. The solid phases formed in the systems were determined by the Schreinemakers wet residues technique, and the corresponding phase diagrams were constructed based on the measured data. Each of the phase diagrams, with two invariant points, three univariant curves, and three crystallization regions corresponding to CsBr, Cs₂LnBr₅·10H₂O and LnBr₃·nH₂O (n = 6, 7), respectively, belongs to the same category. The new solid phase compounds Cs₂LnBr₅·10H₂O are incongruently soluble in water, and they were characterized by chemical analysis, XRD and TG-DTG techniques. The standard molar enthalpies of solution of Cs₂PrBr₅·10H₂O, Cs₂NdBr₅·10H₂O and Cs₂SmBr₅·10H₂O in water were measured to be (52.49 ± 0.48) kJ · mol⁻¹, (49.64 ± 0.49) kJ · mol⁻¹ and (50.17 ± 0.48) kJ · mol⁻¹ by microcalorimetry under the condition of infinite dilution, respectively, and their standard molar enthalpies of formation were determined as being −(4739.7 ± 1.4) kJ · mol⁻¹, −(4728.4 ± 1.4) kJ · mol⁻¹ and −(4724.4 ± 1.4) kJ · mol⁻¹, respectively. The fluorescence excitation and emission spectra of Cs₂PrBr₅·10H₂O, Cs₂NdBr₅·10H₂O and Cs₂SmBr₅·10H₂O were measured. The results show that the upconversion spectra of the three new solid phase compounds all exhibit a peak at 524 nm when excited at 785 nm.     

Effect of Fe2O3 as an accelerator on the reaction mechanism of Al–TiO2 nanothermite system

Thermite reactions between aluminum and metal oxides could lead to the formation of intermetallic matrix composites used in high-temperature industrial applications. Thermite reaction in Al–TiO₂ system needs a considerable amount of energy to take place by mechanochemical or by the combustion synthesis (CS) method due to the low amount of reaction enthalpy in Al–TiO₂ system. In this study, Fe₂O₃ was chosen as a accelerator for this system, to generate a high amount of heat which could be released between Fe₂O₃ and Al, leading to a more convenient reaction between Al and TiO₂ in the CS process. The results of XRD, SEM, and DSC analyses indicated that both the mechanical activation of Al–TiO₂ system in a high-energy ball mill and the Fe₂O₃ addition led to considerable effects of reduction in the reaction temperature and increase in the reaction intensity in Al–TiO₂ nanothermite system. Finally, it was shown that Fe₃Al intermetallic compounds as well as γ-AlTi and alumina phases in the final products were formed after the CS of the milled powders.     

Thermal and kinetic parameters of 30Li2O–55B2O3–5ZnO–xTiO2–(10−x)V2O5 (0 ≤ x ≤ 10) glasses

Journal of Thermal Analysis and Calorimetry - In the present investigation, the effects of titanium and vanadium concentration on the thermal properties have been studied for...     

Thermodynamic stability of solid phases in the system Cu–O–Al2O3 by means of the EMF and DSC-TGA techniques

Journal of Solid State Electrochemistry - Thermodynamic properties of solid phases in the Cu–O–Al2O3 system were measured by means of the EMF method with oxygen concentration galvanic...     

Correlation of CO2 solubility in N-methyldiethanolamine + piperazine aqueous solutions using extended Debye–Hückel model

Solubility data of CO₂ in aqueous N-methyldiethanolamine (MDEA) solutions of concentration (2.52, 3.36, and 4.28) kmol/m³ were obtained at temperatures (313, 323, and 343) K and partial pressures ranging from about (30 to 5000) kPa. A thermodynamic model based on extended Debye–Hückel theory was applied to predict and correlate of CO₂ solubility in various aqueous amine solutions. The effect of piperazine (PZ) concentration on CO₂ loading in MDEA solutions was determined at PZ concentration (0.36, 0.86, and 1.36) kmol/m³. Using experimental data in various temperatures the interaction parameters of activity coefficient model for these systems were determined. The results show the model consistency with experimental and literature data and PZ is beneficial to the CO₂ loading. The comparison of results of this study with previous data work shows the wide range of CO₂ loading considered in this work and the better agreement of model with experimental data. The average absolute relative deviation percent (δ_AAD) for all data points were 8.11%.     

Comparison of the impact of the addition of three alkaline earth metal oxides BaO,SrO and ZnO on sintering of glass–ceramic glazes from the SiO2–Al2O2–CaO–MgO–Na2O–K2O system

Journal of Thermal Analysis and Calorimetry - Glazes are the most important elements in the technology of producing the ceramic wares. They not only give aesthetic effects, like color and gloss,...     

Experimental determination of the liquidus of the binary system (Cu2O + CaO) in air at temperature from (1050 to 1500) °C

The liquidus of the binary system (Cu₂O + CaO) has been experimentally investigated over the temperature range from (1050 to 1500) °C in air. The liquidus has been quantified by the equilibration/quench/analysis technique. Equilibrated specimens were quenched in brine solution of 10 wt% NaCl. Specimens were then examined by Energy-Dispersive X-ray Spectroscopy (EDS) and Electron probe micro-analyzer (EPMA) to quantify liquid chemical compositions. This work reveals that the solubility of CaO in the liquid phase of the binary (Cu₂O + CaO) at higher temperatures is lower than previously reported, and the deviation systematically increases with a corresponding increase in temperature. This is predominant at temperatures between (1300 and 1500) °C where a deviation of up to 5 wt% in CaO solubility is observed. The solubility of Cu₂O in liquid phase for the cuprite saturated section of the binary however is consistent with all the previous authors.     

Thermal characterisation of raw aluminosilicate glazes in SiO<Subscript>2</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–CaO–K<Subscript>2</Subscript>O–Na<Subscript>2</Subscript>O–ZnO system with variable content of ZnO

Thermal properties of raw aluminosilicate ceramic glazes in the multicomponent system of SiO₂–Al₂O₃–CaO–K₂O–Na₂O–ZnO modified by ZnO addition were studied by differential thermal analysis (DTA), dilatometry (DIL), hot-stage microscopy (HSM), X-ray diffraction and fourier transform infrared spectroscopy (FTIR). Using the method of differential thermal analysis, the ways in which zinc oxides affect the temperature of transition (T _g), crystallisation (T _c) were determined. An analysis of the DTA data obtained during thermal tests showed that an increase in ZnO content results in decreasing the T _g value. Also, the influence of ZnO on characteristic temperatures and viscosity of glazes was checked. The introduction of zinc oxide (ZnO) into the glaze composition contributes to the decrease in viscosity of such glazes. An increasing ZnO content in the glazes also causes the reduction in softening (T _s), half-sphere (T _half-sphere) and fusion (T _fusion) temperatures. The mid-infrared spectroscopy showed that the thermal properties of glazes in SiO₂–Al₂O₃–CaO–K₂O–Na₂O–ZnO system modified by addition of ZnO can be associated with the depolymerising influence of zinc ions on the structure of the tested glazes.     

Large-scale synthesis of nano Cu2O/Cu–C for iodide removal in a novel countercurrent two-stage adsorption and membrane separator system

Journal of Radioanalytical and Nuclear Chemistry - A synthesis method was introduced for the large-scale preparation of a nano Cu2O/Cu-modified activated carbon composite, L-nano Cu2O/Cu–C....     

Effect of milling speed on mechanical activation of Al/ZrO2/H3BO3 system to prepare Al2O3–ZrB2 composite powder

A powder mixture of Al/ZrO₂/H₃BO₃ system was mechanically milled under argon in a high-energy planetary mill at different speeds. The XRD and DSC analyses of the as-synthesized samples show that milling operation affects the mechanism, efficiency, and ignition temperature of combustion behavior of the system. XRD analysis of the as-milled samples shows that low-speed milling does not change the phases presented in the sample, while high-speed milling (350, 450 rpm) has led to the formation of new intermetallic phases. This confirms that some reactions between reactants have occurred during high-speed milling.