Ni-Mo氮化物催化剂:合成及其丙烷氨氧化催化性能简

分别采用溶胶-凝胶法、旋转蒸发微波干燥法、共沉淀法、浸渍法和机械混合法制备Ni-Mo氧化物前驱体. 以H₂和N₂的混合气为氮化气体,采用程序升温氮化法合成了镍钼氮化物催化剂. 利用X射线衍射、总氮含量分析、X射线光电子能谱及H₂程序升温还原对Ni-Mo氧化物前体及氮化物催化剂进行了表征. 将上述Ni-Mo氮化物催化剂用于丙烷氨氧化反应中. 结果表明,Ni-Mo氧化物前驱体的制备方法影响其氮化物催化剂上丙烷氨氧化反应性能. Ni-Mo氮化物催化剂中氮物种的移动性及反应性对产物丙烯腈选择性的影响较大,共沉淀法制备的催化剂存在大量的活性氮物种,因而具有良好的催化丙烷氨氧化反应活性.     

介孔氧化铝负载钒催化剂上丙烷氧化脱氢制丙烯

 采用浸渍法制备了介孔氧化铝 (m-Al2O3) 负载钒催化剂 (V/m-Al2O3), 并考察了其催化丙烷氧化脱氢制丙烯反应活性. 通过 N2 吸附-脱附、透射电镜、X 射线粉末衍射、紫外-可见漫反射光谱、氢-程序升温还原和氨-程序升温脱附对催化剂进行了表征. 结果表明, 介孔氧化铝具有大比表面积、窄孔径分布和两维六方相结构, 在其上负载适量的 V 可实现 V 活性物种的高分散及催化剂的弱酸性, 从而有利于提高丙烷转化率和丙烯选择性. 与共合成法制备的含 V 介孔氧化铝 V/m-Al2O3(C) 和浸渍法制备的 V/?-Al2O3 相比, V/m-Al2O3 表现出更高的催化活性. 这与载体较弱的酸性和较大的比表面积以及 V 物种的高分散有关.     

重稀土复合氧化物多孔板状催化剂用于氨氧化制硝酸的研究 Ⅰ.板状催化剂的反应性能

制备了用于氨氧化制硝酸的含重稀土和钴的复合氧化物催化剂。研究了几种不同的载体和它们的几何形状对催化剂活性的影响。测定了板状催化剂的传质因素。用X射线电子能谱、热重分析等方法比较了复合氧化物和Co_3O_4催化剂的反应稳定性。结果表明,用α-Al_2O_3载体制备的多孔板状催化剂与粒状和蜂窝状催化剂相比具有比表面积大,表面反应性能好等特点。复合氧化物催化剂较Co_3O_4催化剂具有更好的反应稳定性,其原因主要是复合氧化物具有稳定的晶相结构和Co~(3+)活性中心离子。     

Mn-Ce-O催化剂组成对氨超临界水氧化性能的影响

用共沉淀方法制备了锰铈摩尔比分别为10/0、8/2、6/4、5/5、4/6、2/8和0/10的七种Mn-Ce-O复合氧化物催化剂.在450 ℃、25 MPa、停留时间1 s和氧化剂量为化学计量2.94倍的条件下,利用连续超临界水氧化反应装置考察了催化剂组成与其催化氨降解性能的关系.结果表明,催化剂组成与其活性间有着强烈的相关性,锰铈摩尔比为5/5的催化剂表现出最高的活性,氨转化率达到99.7%.用低温N2吸附、X射线衍射以及程序升温还原等方法表征了催化剂比表面积、物相结构和氧化还原性能,揭示了Mn和Ce的氧化物之间存在协同作用.     

负载Pd密偶催化剂的载体效应

采用尿素水解法或吸附沉淀法制备了金属氧化物载体,并用浸渍法负载0.5%Pd制得了Pd/Sn0.4Zr0.6O2,Pd/ZrO2,Pd/SnO2,Pd/SnO2-Al2O3和Pd/Al2O3催化剂.采用原位漫反射红外光谱、拉曼光谱、X射线光电子能谱和程序升温还原等方法对催化剂结构进行了表征,探讨了不同载体对表面PdOx物种化学吸附性质和氧化还原性能的影响,并与样品的丙烷氧化活性相关联.漫反射红外光谱表明,在Pd/SnO2-Al2O3中,Sn对Al2O3表面的Pd原子簇起到稀释作用,促进了Pd的分散,使得其CO线式吸附强度明显高于Pd/Al2O3,但Pd过高的分散度不仅减少了表面Pd-PdO活性位对的数目,而且使反应中间物种Pd-OH之间脱水困难,因而阻塞了活性位,降低了其循环氧化还原活性;而在Sn0.4Zr0.6O2复合氧化物载体中,SnO2有效地阻止了四方晶相ZrO2向稳态单斜晶相转变,且复合载体的比表面积较ZrO2和SnO2有所增加,其表面PdOx物种的分散度适中.此外,Sn0.4Zr0.6O2复合氧化物负载的Pd的价态介于Pd0与Pd2 之间,表面氧空位较多,促进了丙烷中C-H键的活化,使比表面积较低的Pd/Sn0.4Zr0.6O2具有最好的催化丙烷氧化能力,相反比表面积较高的Pd/SnO2-Al2O3活性很差,说明分散度适中且具有较低氧化态的PdOx(0相似文献   

固相球磨法制备丙烷氧化脱氢V2O5/NiO催化剂

以不同温度焙烧制备的NiO和V2O5为前驱物,采用固相球磨法制备了V2O5/NiO催化剂,考察了前驱物的焙烧温度对该催化剂丙烷氧化脱氢制丙烯反应性能的影响,并采用x射线衍射、N2物理吸附、电感耦合等离子体原子发射光谱、透射电子显微镜、H2程序升温还原和x射线光电子能谱等对催化剂进行了表征.结果表明,固相球磨法制备的V2O5/NiO催化剂表现出较好的丙烷氧化脱氢制丙烯催化性能,当以400℃焙烧的氧化物为前驱体时,V2O5/NiO催化剂表面含有较多的未完全还原氧物种Oδ-,因而表现出了较高的丙烯选择性.在475℃反应时,丙烷转化率可达20.1%,丙烯选择性达到71.2%.     

担载钒氧化物催化剂对丙烷选择氧化性能

用等体积浸渍法制备了SBA-15担载的钒基氧化物催化剂,使用X射线衍射（XRD）分析、氮气吸附、紫外激光拉曼、傅里叶变换红外（FTIR）光谱和紫外-可见漫反射（UV-Vis DRS）光谱对催化剂的结构进行了表征,并评价了催化剂对丙烷选择氧化的活性与选择性.实验结果表明SBA-15载体对丙烷选择氧化的活性优于常规的SiO₂载体.SBA-15担载的低载量催化剂是高分散的催化剂体系,在低钒载量（n（V）/n（Si）<2.5%）时,催化剂具有规则的六方介孔结构.低钒载量（n（V）/n（Si）<0.1%）时,隔离四配位的钒氧化物是丙烷选择氧化生成醛类化合物的活性物种;高钒载量（n（V）/n（Si）>2.5%）时,聚合六配位的钒氧化物和微晶钒氧化物是丙烷脱氢或深度氧化的活性物种.     

Cr掺杂的丙烷选择氧化制丙烯酸高效催化剂

在丙烷选择氧化制丙烯酸催化剂MoVTeNbOx的活性相M1基础上掺杂一定量的Cr,当Cr/Nb摩尔比为0.002时,催化剂具有很高的丙烯酸选择性(78.3%)和收率(50.7%);并采用X射线衍射、X射线光电子能谱、程序升温还原、O2程序升温脱附、NH3程序升温脱附和异丙醇氧化等手段对催化剂的构效关系进行了探讨.结果表明,适量Cr的添加可调节催化剂表面Mo6+,V5+和Te4+等物种含量,提高催化剂的氧化能力,使丙烷转化率增加.同时,适量Cr的添加使得催化剂表面酸强度下降,酸性位点数量减少,从而抑制丙烯酸的深度氧化,提高了丙烯酸选择性.     

SBA-15 负载 β-Mg2V2O7 催化剂的制备及其催化丙烷选择氧化脱氢的性能

 以 MgO 修饰的 SBA-15 为载体, 采用浸渍法制备了负载 β-Mg2V2O7 催化剂, 并运用 X 射线衍射、拉曼光谱、紫外-可见漫反射光谱和 H2 程序升温还原等技术对催化剂 V 中心的结构和还原性能进行了表征. 结果表明, β-Mg2V2O7 具有与 α-Mg2V2O7 相同的结构单元, 但其催化丙烷氧化脱氢 (ODH) 反应的初始活性和初始选择性均低于后者. 与体相 β-Mg2V2O7 相比, 负载的 β-Mg2V2O7 上 V 中心分散度以及丙烷 ODH 反应活性和选择性更高, 520 oC 时丙烷 ODH 反应的初始活性提高了约 20 倍, 丙烯初始选择性也从体相的 88.3% 提高到 94.1%, 接近于 α-Mg2V2O7 (94.6%), 并且在 20% 的丙烷转化率时也表现出相似的规律. 这与表征催化剂选择性的两个本征动力学参数 k1/k2 (丙烷初级 ODH 和燃烧反应速率常数之比) 和 k3/k1 (次级丙烯燃烧和初级丙烷 ODH 反应速率常数之比) 反映出的规律一致. 这些对体相和负载的 Mg2V2O7 催化剂催化丙烷 ODH 反应本征特性的认识将有助于设计合成更高效的 Mg-V-O 催化剂, 如基于 α-Mg2V2O7 结构的高分散催化剂, 以获得更高的丙烷 ODH 反应活性和选择性.     

Ni- Co- Al混合氧化物的制备及其丙烷氧化脱氢催化性能

采用恒定pH共沉淀法制备不同Ni/Co摩尔比的3(Ni_xCo_(1-)_x)-Al类水滑石前驱体, 600℃焙烧得3(Ni_xCo_(1-)_x)Al混合氧化物(MMO)催化剂(x=1, 0.95, 0.90, 0.75, 0.50, 0.25, 0),通过电感耦合等离子体发射光谱、 N_2物理吸附-脱附、 X射线衍射和透射电子显微镜表征其组成、表面织构、晶相和微观形貌,考察Ni/Co摩尔比对其丙烷氧化脱氢制丙烯催化性能的影响.结果表明, 3(Ni_(0.90)Co_(0.10))Al MMO催化剂催化性能最佳:丙烯选择性随反应温度升高未发生明显降低,反应温度500℃时丙烷转化率31%、丙烯选择性48%,丙烯收率15%,且催化剂寿命良好.通过X射线光电子能谱、 H_2程序升温还原和原位电导测试研究发现,掺杂少量Co后催化剂表面Ni(II)与Co(II/III)间存在电子交互作用,表面类NiO相分散性提高,晶格氧物种增多,催化剂具有优良的氧化还原可逆性.     

Operando and in situ Raman studies of alumina-supported vanadium phosphate catalysts in propane ammoxidation reaction: activity, selectivity and active phase formation

Alumina-supported VPO materials are efficient catalysts for acrylonitrile production by the propane ammoxidation reaction. In order to understand the structure-activity relationship and the nature of active sites, operando Raman-GC analyses follow the states of vanadium and phosphorous species on an alumina support during ammoxidation. These oxides were supported on γ-alumina by incipient wetness impregnation at a total V + P loading of two monolayers, which led to incipient formation of nanoscaled VPO crystallites possessing a high surface-to-volume ratio. Since catalysis occurs at the catalyst surface, which is related to the surface and outermost layers, this approach allows studying surface species phase transformations near the surface, and relates changes in activity and selectivity to variations in composition and structure. Dispersed surface V(5+) species appear selective to acetonitrile and V(4+) species would promote selectivity to acrylonitrile. This study suggests that V(3+) is probably involved in redox processes during propane ammoxidation and that the balance between these vanadium species would be determined by activation process.     

Preparation and characterization of vanadium(IV) oxide supported on SBA-15 and its catalytic performance in benzene hydroxylation to phenol using molecular oxygen

Preparation of dispersed transition metal oxides catalyst with low oxidation state still remains a challenging task in heterogeneous catalysis.In this study,vanadium oxides supported on zeolite SBA-15 have been prepared under hydrothermal condition using V 2 O 5 and oxalic acid as sources of vanadium and reductant,respectively.The structures of samples,especially the oxidation state of vanadium,and the surface distribution of vanadium oxide species,have been thoroughly characterized using various techniques,including N 2-physisorption,X-ray diffraction(XRD),transmission electron microscopy(TEM),X-ray photoelectron spectroscopy(XPS),UV-visible spectra(UV-Vis) and UV-visible-near infrared spectra(UV-Vis-NIR).It is found that the majority of supported vanadium was in the form of vanadium(IV) oxide species with the low valence of vanadium.By adjusting hydrothermal treatment time,the surface distribution of vanadium(IV) oxide species can be tuned from vanadium(IV) oxide cluster to crystallites.These materials have been tested in the hydroxylation of benzene to phenol in liquid-phase with molecular oxygen in the absence of reductant.The catalyst exhibits high selectivity for phenol(61%) at benzene conversion of 4.6%,which is a relatively good result in comparison with other studies employing molecular oxygen as the oxidant.     

丙烷直接氨氧化制丙烯腈催化剂的研究进展

丙烷直接氨氧化制丙烯腈是一条潜在的具有巨大经济效益的丙烯腈生产路线。本文概述了丙烷直接氨氧化制丙烯腈的催化反应机理，对丙烷直接氨氧化制丙烯腈的催化反应路径进行了归纳，同时对丙烷直接氨氧化制丙烯腈催化剂设计的思想以及日前所开发的几类丙烷直接氨氧化制丙烯腈催化剂体系加以了总结，重点介绍了锑酸盐和钼酸盐催化剂，对锑酸盐和钼酸盐催化剂活性相的结构、影响活性相形成的因素以及催化剂的结构与催化反应性能的关系等问题作了阐述。     

Solvothermal synthesis of nanosized particles of vanadium oxide

The interaction of vanadyl acetate, vanadium(V) oxide, and vanadium(V) isopropylate with capronic acid has afforded a series of nanosized vanadium oxide powders. The products structure has been studied by X-ray diffraction analysis. Both amorphous and crystalline powders of vanadium oxide can be prepared depending on the starting compound, temperature, and the synthesis duration, the V₂O₃ (karelianite) structure being in all the cases the most thermodynamically stable. Photocatalytic properties of the prepared powders have been studied.     

Oxidation of glyoxal to glyoxylic acid by oxygen over V2O5/C catalyst

A novel vanadium oxide catalyst supported on active carbon was prepared by an incipient wetness impregnation method, and the precursor was obtained from oxalic acid aqueous solutions of NH4VO3. The catalyst was applied liquid phase oxidation of glyoxal to glyoxylic acid. It was found that V2O5/C catalyst exhibited obvious activity for glyoxal oxidation. Glyoxylic acid could be obtained without pH regulation during the reaction. By using this catalyst, the conversion of glyoxal and the yield of glyoxalic acid were 29.2% and 13.6%, respectively at 313 K and oxygen flow 0.1 L/rain after reaction for 10 h.     

双溶剂浸渍法制备VOX/MCF催化剂及丙烷选择氧化

采用双溶剂法制备了负载型氧化钒类催化剂(VOx/MCF),N2物理吸附、X射线衍射、透射电镜、拉曼光谱、程序升温脱附、程序升温还原等系统研究了催化剂的物化性质并测试了其在丙烷选择氧化反应中的催化性能.结果表明,由双溶剂法制备的VOx/MCF催化剂具有较好的催化活性,且在氧化钒负载量基本一致的前提下,双溶剂法制备的VOx/MCF催化剂比普通浸渍法制备的VOx/MCF具有更高的催化活性,这与双溶剂法的制备过程可以使得钒物种尽可能进入载体内表面,有利于氧化钒的较好分散有关,而高度分散的氧化钒物种,正是丙烷选择氧化反应的活性中心.     

Preparation,Solid‐state Characteristics,and Catalytic Properties of Promoted Vanadium Phosphate Materials

The syntheses of transition metal promoted (M = Co, Cr, Fe, Mo) supported vanadium phosphate (VPO) catalysts (TiO₂ (anatase), γ‐Al₂O₃) and their characterization by N₂‐adsorption, X‐ray diffractometry (XRD), FTIR‐spectroscopy and determination of V‐valence state is reported. The catalytic properties were checked in the heterogeneous catalytic ammoxidation of 2, 6‐dichlorotoluene to the corresponding nitrile. The catalyst samples were prepared by synthesis of the precursor compound VOHPO₄ · 0.5 H₂O, impregnation using various metal salt solutions and mixing with the support materials. The characterization revealed increased surface areas for all the promoted samples in comparison to the basic materials. XRD showed the formation of (VO)₂P₂O₇ after calcinations as well as patterns of support materials (anatase, γ‐Al₂O₃). The formation of crystalline proportions of mixed oxides were not observed. The catalytic ammoxidation runs revealed a significant effect of the promoter metals on the catalytic properties by an increase of yield by ca. 20 % compared to bulk VPO. Almost complete conversion of 2, 6‐dichlorotoluene and 81 % yield of nitrile were observed using a 25 %VPCoO/γ‐Al₂O₃ catalyst.     

The role of surface basal planes of layered mixed metal oxides in selective transformation of lower alkanes: propane ammoxidation over surface ab planes of Mo-V-Te-Nb-O M1 phase

The surface ab planes of the M1 phase exposed selectively after atomic layer deposition (ALD) of alumina followed by crushing showed significantly improved selectivity to acrylonitrile during propane ammoxidation. The results demonstrated the importance of surface ab planes for the activity and selectivity of the M1 phase in propane ammoxidation and general utility of surface modification by ALD in studies of catalytic behavior of surface planes in layered mixed metal oxides.