Performance improvement of polysulfone ultrafiltration membrane by blending with polyaniline nanofibers

Polyaniline (PANI) nanofibers were used to improve hydrophilic property and permeability of polysulfone (PS) membrane. PS membrane and PS/PANI nanofibers blended membranes with different PANI–PS mass ratios (1, 5, 10, and 15 wt.%) were prepared by phase inversion process. The blended membranes showed similar bovine serum albumin (BSA) and albumin egg (AE) rejections to PS membrane. The blended membranes had larger porosity and better hydrophilic property than PS membrane, which caused the improvement of their permeability. Pure water fluxes of the blended membranes with PANI–PS mass ratios of 1 and 15 wt.% were 1.6 and 2.4 times that of PS membrane, respectively. During the filtration of BSA solution, the blended membranes had slower flux decline rate than PS membrane. Moreover, stable permeate fluxes of the blended membranes with PANI–PS mass ratios of 1 and 15 wt.% were 2.0 and 2.5 times that of PS membrane, respectively. Compared with PS membrane, mechanical property and thermal stability of the blended membranes with less PANI–PS mass ratio, e.g. 1 wt.%, had no obvious change. For the blended membrane with PANI–PS mass ratio of 15 wt.%, breaking strength increased 28% and elongation at break decreased 30.6%.     

Synthesis,characterization and microwave absorption properties of polyaniline/Sm-doped strontium ferrite nanocomposite

Sm-doped strontium ferrite nanopowders (SrSm_0.3Fe_11.7O₁₉) and their composites of polyaniline (PANI)/SrSm_0.3Fe_11.7O₁₉ with 10 wt% and 20 wt% ferrite were prepared by a sol–gel method and an in-situ polymerization process, respectively. The structure, magnetic properties and microwave absorption properties of the samples were characterized by means of X-ray diffraction (XRD), Fourier transform infrared spectra (FT-IR), transmission electron microscope (TEM), vibrating sample magnetometer (VSM) and vector network analyzer, respectively. The particle size of SrSm_0.3Fe_11.7O₁₉ was about 35 nm by using XRD. The ferrite successfully packed by PANI. PANI/SrSm_0.3Fe_11.7O₁₉ possessed the best absorption property with the optimum matching thickness of 3 mm in the frequency of 2–18 GHz. The value of the maximum reflection loss (RL) were −26.0 dB at 14.2 GHz with the 6.5 GHz bandwidth and −24.0 dB at 13.8 GHz with the 7.9 GHz bandwidth for the samples with 10 wt% and 20 wt% ferrite, respectively.     

Preparation and characterization of polyethersulfone/silver nanocomposite ultrafiltration membrane for antibacterial applications

Antimicrobial ultrafiltration membranes were prepared by coating silver nanoparticles on the surface of polyethersulfone (PES) membranes which were fabricated via phase inversion induced by the immersion precipitation technique, and their morphology and performance were compared with the antimicrobial PES membranes synthesized by adding the silver nanoparticles into the casting solution during the phase inversion process. For this purpose, stable and uniform colloidal solutions of the silver nanoparticles were prepared by chemical reduction of silver salt using fructose and dimethylformamide as a reducing agent. The silver nanoparticles were characterized by ultraviolet–visible spectroscopy, X‐ray powder diffraction and dynamic light scattering analysis. The morphology and surface properties of the prepared membranes were examined by field emission scanning electron microscopy and atomic force microscopy analysis. Moreover, the separation properties, antimicrobial efficiency and amount of silver release from the PES nanocomposite membranes during the cross flow ultrafiltration were determined. The results indicated that the silver content of the coated PES membranes was greater than the membranes fabricated by the solution blending method. Also, the permeation flux of the silver‐coated membranes was similar to the neat PES membranes, while the membranes prepared by the second approach had less flux. The membranes synthesized by both coating and blending methods showed high antimicrobial and bactericidal activity against gram‐negative bacteria such as Escherichia coli and gram‐positive bacteria such as Staphylococcus aureus. Finally, the prepared antimicrobial membranes were successfully used for the ultrafiltration of raw milk to reduce the microbial load during the concentration process. Copyright © 2014 John Wiley & Sons, Ltd.     

Synthesis,characterization and antibacterial properties of a novel nanocomposite based on polyaniline/polyvinyl alcohol/Ag

In this study, a novel nanocomposite based on polyaniline/polyvinyl alcohol/Ag (PANI/PVA/Ag) has been successfully synthesized. The chemical reduction method was used to produce Ag nanoparticle colloidal solution from Ag⁺ ions. The polymerization of aniline occurred in situ for the preparation of polyaniline (PANI) in the presence of ammonium persulfate. With exposure to Ag nanoparticles on the PANI/PVA composite, a new nanocomposite was obtained. The morphology and particle size of the novel nanocomposite was studied by scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier transform infrared (FT-IR) analyses. According to XRD analysis, the size of nanoparticles was found to be in the range of 10–17 nm. SEM images showed the favored shape of nanoparticles as triangle which is a benign shape for antibacterial analysis. The antibacterial activity of the obtained nanocomposite was also evaluated against Gram positive bacteria Staphylococcus aureus (Staph. aureus) and Gram negative Escherichia coli (E. coli) using the paper disk diffusion method. The antibacterial study showed that the PANI/PVA composite did not have a very good antibacterial activity but PANI/PVA/Ag nanocomposites were found to be effective against two bacteria.     

Preparation and characterization of a conductive polyaniline/polysulfone film and evaluation of the effect of co-solvent

A novel conductive dense membrane composed of polyaniline (PANI) and polysulfone (PSU) was prepared. To improve the solubility of PANI in N-methyl pyrrolidone (NMP) and consequently increase the conductivity of the eventual film, a tertiary amine (1,3-dimethyl-2-imidazolidinone, DMI) was added to the solvent as a co-solvent. Different PANI solution concentrations in NMP/DMI were used to make blend films via solution blending with PSU solution in NMP in different ratio’s of PANI/PSU. The effect of the PSU fraction on the properties of the membrane has been investigated. The electrical conductivity, doping degree, crystallinity, miscibility of the polymers and shape stability were investigated. It was observed that an increase in the PSU fraction causes a decrease in the conductivity as well as less film deformation after doping. The conductivity and shape stability of the blend film were optimized by a change in PANI concentration in the casting solution and a change in the PSU fraction. The best conductivity was achieved using 3% PANI solution in NMP/DMI and the minimum percentage of PSU, allowing good shape stability after doping, was found to be 40%.     

Antifouling ultrafiltration membrane composed of polyethersulfone and sulfobetaine copolymer

A new random copolymer was synthesized by reacting hydrophilic N,N-dimethyl-N-methacryloxyethyl-N-(3-sulfopropyl) (DMMSA) with hydrophobic butyl methacrylate (BMA) through a conventional radical polymerization. The as-prepared sulfobetaine copolymer (DMMSA–BMA) was blended with polyethersulfone (PES) to fabricate antifouling ultrafiltration membrane for BSA separation. The X-ray photoelectron spectroscopy analysis of blend membranes revealed concentration of sulfobetaine groups at the membrane surfaces that endowed the membrane with higher hydrophilicity and better antifouling property. For the membrane with 8.0 wt% DMMSA–BMA copolymer concentration (No. 5), irreversible fouling has been considerably reduced and the flux recovery rate of the blend membrane reached as high as 82.8%. Furthermore, the blend membrane could effectively resist BSA fouling in a wide pH range from 4.0 to 8.0.     

Pervaporation separation of water + isopropanol mixtures using novel nanocomposite membranes of poly(vinyl alcohol) and polyaniline

Novel nanocomposite polymeric membranes containing nanosized (30–100 nm) polyaniline (PANI) particles dispersed in poly(vinyl alcohol) (PVA) were prepared and used in the pervaporation separation of water–isopropanol feed mixtures ranging from 10 to 50 mass% of water at 30 °C. Of the three nanocomposite membranes prepared, the membrane containing 40:60 surface atomic concentration ratio of PANI:PVA produced the highest selectivity of 564 compared to a value of 77 observed for the plain PVA membrane. Flux of the nanocomposite membranes was lower than those observed for the plain PVA membrane, but selectivity improved considerably. Membranes were characterized by differential scanning calorimetry, dynamic mechanical thermal analyzer, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy and scanning electron microscopy. The highest selectivity with the lowest flux was observed for 10 mass% water containing feed mixture. Flux increased with increasing amount of water in the feed, but selectivity decreased considerably. These results were attributed to the acid-doped PANI particles in the PVA membrane as a result of change in the micromorphology of the nanocomposite membranes. In addition, molar mass between cross-links and fractional free volume of the membranes are responsible for the varying membrane performance. Temperature effect on permeability was investigated for 10 mass% water containing feed with the membrane containing higher concentration of PANI particles, the presence of which could be responsible for varied effect of water permeation through the membrane. Membranes of this study could remove as much as 98% of water from the feed.     

Facile fabrication and characterization of novel polyaniline/titanate composite nanotubes directed by block copolymer

In this work, we present a facile method for preparation of novel polyaniline(PANI)/titanate composite nanotubes by in situ chemical oxidative polymerization directed by poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (PEO-PPO-PEO) triblock copolymer. The block copolymer adsorbed onto the surface of the titanate nanotubes acts as a soft template. The obtained nanocomposite has a core-shell structure in which titanate nanotubes are encapsulated by uniform PANI layers. Their structure and morphology were characterized by various experimental techniques. A possible formation mechanism of composite nanotubes is also proposed in the paper.     

A comparison between polysulfone,zirconia and organo-mineral membranes for use in ultrafiltration

In this paper, representative polymeric (a PSf/PVP membrane), ceramic (a ZrO₂ membrane) and organo-mineral (a ZrO₂/PSf membrane) ultrafiltration membranes, all in the tubular configuration, are being compared for their basic membrane properties, and for the typical ultrafiltration application of protein recovery of cheese whey. These three different membranes with a quite similar pore size (the cut-off values for each of the three membranes were comprised between 25 000 and 50 000 Dalton) showed pure water permeability coefficients between 135 and 1250 l/h m² bar. The highest pure water flux was found for the organo-mineral membrane, the lowest for the polymeric membrane. By FESEM analysis of the top-surfaces (skin) of both the PSf/PVP and the ZrO₂/PSf membrane a strong difference in surface-porosity was found. These results were claimed to partially explain the difference in pure water flux. From SEM pictures of the cross-section of the ZrO₂/PSf membrane it could also be seen that the skin layer thickness is smaller, at these places where particles are present near the skin-surface, compared to the rest of the membrane as well as to the skin of the PSf/PVP membrane. These latter observations were also used to further explain the flux difference between the PSf/PVP and the ZrO₂/PSf membrane.     

Preparation, characterization and effect of annealing on performance of cellulose acetate/sulfonated polysulfone and cellulose acetate/epoxy resin blend ultrafiltration membranes

Polymeric membranes based on cellulose acetate (CA)--sulfonated polysulfone blends at three different polymer compositions were prepared by solution blending and phase inversion technique, characterized and subjected to annealing at 70, 80 and 90 °C. The permeate water flux, separation of bovine serum albumin and its flux by the blend membranes before and after thermal treatment, have been compared and discussed. Similarly, CA and epoxy resin (diglycidyl ether of bisphenol-A) were blended in various compositions, in the presence and in the absence of polyethyleneglycol 600 as non-solvent additive, using N,N^′-dimethylformamide as solvent, and used for preparing ultraflltration membranes by phase inversion technique. The polymer blend composition, additive concentration, casting and gelation conditions were optimized. Blend membranes were characterized in terms of compaction, pure water flux, water content and membrane resistance. The effects of polymer blend composition and additive concentration on the above parameters were determined and the results are discussed.     

Preparation and characterization of aqueous polyaniline battery using a modified polyaniline electrode

A rechargeable battery of the type Zn/ZnCl₂, NH₄Cl/polyaniline (PAn)-reticulated vitreous carbon was successfully prepared based on a PAn modified electrode. Voltage of the battery was 1.2 V. Charge-discharge behavior at a constant load of 2.5 k, recycle ability and the rate of self-discharge were measured. The results showed that the battery has a capacity of 121 mA h g⁻¹ polymer weight and coulombic efficiency was in the range between 75% and 100%. Self-discharge rate was less than 1% per day and the battery showed a good recycle ability. It was also found that even after 70 cycles, the decrease in the open-circuit voltage was less than 5%.     

Preparation,characterization and application of polyaniline/epoxide polysiloxane composite films

Composites of polyaniline(PAn) and epoxide polysiloxane(EPSi) are reported for the first time. EPSi is designed, synthesized and N-grafted onto the PAn backbone through covalent bonds. As-prepared EPSi-g-PAn composites are soluble in organic solvents and the corresponding films can be easily produced via a simple solution-casting procedure. The composite films combine the mechanical characteristics of EPSi and the chemical properties of PAn, enabling the facile introduction of the noble metal particles. The successful fabrication of the composites is confirmed by the investigation of the molecular structure, crystalline structure and microstructure of the materials. The resulting composite films containing noble metal particles are employed as the catalysts for the hydrogenation of phenol to produce cyclohexanone, which exhibit the convenience and recyclability for usage as well as the high catalytic activities, including the conversion ratio of 97%-100% and the selectivity as high as 84%-98%. The present work not only provides a new method to improve the processability of the conducting polymers but also describes a kind of composite materials that may display outstanding preformances in industrial catalysis.     

Fouling reduction in poly(acrylonitrile-co-acrylamide) ultrafiltration membranes

Ultrafiltration membranes with similar pore sizes were prepared from acrylonitrile homopolymer and copolymers with increasing acrylamide content. The membranes containing acrylamide were more hydrophilic, had a smaller dispersion force component of the surface energy, and a smaller negative zeta potential than those prepared from the homopolymer. The effect of the differing surface chemistry of these membranes with similar pore sizes was examined by studying the ultrafiltration of bovine serum albumin (BSA) as a function of feed pH. The hydrophilic membranes showed higher permeate fluxes and flux recoveries than the hydrophobic membrane, in spite of their reduced repulsive electrostatic interaction. With increasing pH, protein transmission increased markedly for the acrylamide containing membranes whereas the transmission through the hydrophobic membrane remained low. These rejection data are explained by the combined effects of the increased hydrophilicity, decreased dispersive surface energy and reduced electrostatic repulsion of the acrylamide containing membranes.     

Enhancing the antifouling property of polyethersulfone ultrafiltration membranes through surface adsorption-crosslinking of poly(vinyl alcohol)

An adsorption-crosslinking process of poly(vinyl alcohol) (PVA) was introduced to modify the surface of polyethersulfone (PES) ultrafiltration membranes for enhancement of their antifouling property. XPS and water contact angle measurement confirmed the obvious enhancement of surface hydrophilicity. Ultrafiltration results showed that the spreading of PVA chains over the hydrophobic membrane surface caused substantial but acceptable decrease on membrane flux. The fouling type analysis indicated that PVA adsorption effectively improved the antifouling property of PES membranes. With a PVA concentration of 0.5 wt% and three cycles of alternative adsorption-crosslinking, the total and irreversible fouling ratio of modified membranes were 0.38 and 0.22, respectively, much lower than those of control PES membrane (0.61 and 0.47), and the flux recovery ratio was increased accordingly. The long-term ultrafiltration experiment demonstrated the improvement of recycling property and the reliability of adsorption-crosslinking process.     

Versatility of hydrophilic and antifouling PVDF ultrafiltration membranes tailored with polyhexanide coated copper oxide nanoparticles

Hydrophilic poly(vinylidene fluoride) (PVDF) nanocomposite ultrafiltration (UF) membranes with excellent antifouling and antibiofouling characteristics are fabricated by employing polyhexanide coated copper oxide nanoparticles (P–CuO NPs). The presence of P–CuO NPs is played a significant role in altering the PVDF membrane matrix and probed by XRD, FTIR, FESEM and contact angle analysis. The PVDF/P–CuO nanocomposite membranes exhibited an outstanding antifouling performance indicated by the superior pure water flux, effective foulant separation and maximum flux recovery ratio during UF experiments as a result of the formation of the hydrophilic and more porous membrane due to the uniform distribution of P–CuO NPs. Particularly, the PVDF/P–CuO-3 membrane showed higher PWF of 152.5 ± 2.4 lm⁻²h⁻¹ and porosity of 64.5% whereas the lower contact angle of 52.5°. Further, it showed the higher rejection of 99.5 and 98.4% and the flux recovery ratio of 99.5 and 98.5% respectively for BSA and HA foulants, demonstrated its increased water permeation, foulant separation and antifouling behavior. Further, the decent antibacterial activity is showed by the PVDF/P–CuO nanocomposite membranes with the formation of halo-zone around the membrane when exposed to the bacterial medium demonstrated that, by this process an antibacterial water treatment membrane can be developed by simple phase inversion technique with good membrane stability.     

Electrorheological characteristics of polyaniline/titanate composite nanotube suspensions

In this paper, one-dimensional polyaniline/titanate (PANI/TN) composite nanotubes were synthesized by in situ chemical oxidative polymerization directed by block copolymer. These novel nanocomposite particles were used as a dispersed phase in electrorheological (ER) fluids, and the ER properties were investigated under both steady and dynamic shear. It was found that the ER activity of PANI/TN fluids varied with the ratio of aniline to titanate, and the PANI/TN suspensions showed a higher ER effect than that made by sphere-like PANI/TiO₂ nanoparticles. These observations were well interpreted by their dielectric spectra analysis; a larger dielectric loss enhancement and a faster rate of interfacial polarization were responsible for a higher ER activity of nanotubular PANI/TN-based fluids.     

Preparation, characterization, and photocatalytic activity of polyaniline/ZnO nanocomposite

Polyaniline (PANI)/zinc oxide (ZnO) nanocomposite was synthesized by in-situ polymerization. X-ray diffraction patterns, UV?Cvisible spectroscopy, SEM, and TEM were used to characterize the composition and structure of the nanocomposite. Nanostructured PANI/ZnO composite was used as photocatalyst in the photodegradation of methylene blue dye molecules in aqueous solution. The photocatalytic activity of PANI/ZnO nanocomposite under UV and visible light irradiation was evaluated and was compared with that of ZnO nanoparticles. ZnO/PANI core?Cshell nanocomposite had greater photocatalytic activity than ZnO nanoparticles and pristine PANI under visible light irradiation. According to these results, application of PANI as a shell on the surface of ZnO nanoparticles causes the enhanced photocatalytic activity of the PANI/ZnO nanocomposite. Also UV?Cvisible spectroscopy studies showed that the absorption peak for PANI/ZnO nanocomposite has a red shift toward visible wavelengths compared with the ZnO nanoparticles and pristine PANI. The effect of different operating conditions on the photocatalytic performance of PANI/ZnO nanocomposite in the photodegradation of methylene blue dye molecules was investigated in a bath experimental setup.     

抗污染PVA/PVDF电纺纳米纤维复合超滤膜的制备及过滤性能

以聚对苯二甲酸二醇酯(PET)无纺布为基底,聚偏氟乙烯(PVDF)纳米纤维为支撑层,聚乙烯醇(PVA)纳米纤维膜为分离层,采用静电纺丝法制备超滤膜,并用水/丙酮混合溶液对复合纳米纤维膜表面进行溶液处理,再加入戊二醛交联改性得到致密分离层.采用扫描电子显微镜(SEM)和红外光谱(FTIR)表征了复合超滤膜的表面,用水接触角(WCA)表征复合超滤膜的亲水性.在0.02 MPa恒压下死端过滤油/水乳液,测试复合超滤膜的过滤性能.结果表明,最优条件下制备的复合超滤膜死端过滤油/水乳液的通量为(42.50±4.78)L/(m~2·h),截留率达到(95.72±0.33)%;循环使用5次后,依然具有较好的过滤性能,常压下死端过滤复合超滤膜的纯水通量为(3469±28)L/(m~2·h).     

Tailoring polyethersulfone/quaternary ammonium polysulfone ultrafiltration membrane with positive charge for dye and salt selective separation

Polyethersulfone (PES)/quaternary ammonium polysulfone (QAPSf) blend ultrafiltration (UF) membranes with positive charge were fabricated by nonsolvent induced phase separation (NIPS) for use in dye and salt selective separation. QAPSf was synthesized by nucleophilic substitution with chloromethylated polysulfone (CMPSf). The effect of the PES/QAPSf mass ratio on the morphology and performance of blend UF membranes were studied. The membranes' zeta potentials gradually changed from negative to positive with decreases in the PES/QAPSf mass ratio. At PES/QAPSf mass ratios of 30:70 and 10:90, the zeta potentials of the membranes reached +1.8 mV and + 5.9 mV, respectively. Additionally, the contact angles of the membranes decreased from 74° to 52° as the QAPSf content increased from 0 wt% to 90 wt%. Furthermore, the membrane with a PES/QAPSf mass ratio of 30:70 showed a high water permeance (181.4 LMH bar⁻¹) and excellent dye and salt selective separation performance. The rejection ratios reached 99.1%, 87.8%, 99.6%, and 92.4% for dyes Congo red, methyl blue, Alixin blue 8GX, and basic blue 24, respectively, while those for salts Na₂SO₄, MgSO₄, MgCl₂, and NaCl were ≤ 10%. In addition, the PES/QAPSf membranes showed excellent antifouling performance and good operating stability with dye-salt mixtures of various pHs and salt concentrations.     

Preparation and characterization of anthracenecarboxylic acid doped polyaniline thin films

Doped polyaniline films were prepared with electrochemistry method. A small conjugated molecule, anthracenecarboxylic acid(2-ACA), was used as the dopant, considering its electrical activeness due to the conjugated π-π* structure. Film morphology of doped and undoped polyaniline samples was investigated. The corresponding changes in optical and electrical properties after ACA doping were discussed. By measuring and calculating their energy level distribution, a promising application of polyaniline thin films as buffer layer in optic-electric devices is expectable.