Views on quality tests of radiopharmaceuticals

The quality tests of radionuclides produced from generators (⁹⁹Mo→^99mTc,¹¹³Sn→^113mIn) have been reviewed. The quality controls of radiopharmaceuticals derived from these radionuclides and prepared with the help of ready-for-use reagents assembled in kits have been presented. The possibility of new tests regarding sterility (by means of a radiometric method) and detection of endotoxin (based on gelification of limulus amoebocyte lysate) have been suggested.     

Au@Pt Core-Shell Nanoparticle Bioconjugates for the Therapy of HER2+ Breast Cancer and Hepatocellular Carcinoma. Model Studies on the Applicability of 193mPt and 195mPt Radionuclides in Auger Electron Therapy

^193mPt and ^195mPt radionuclides are therapeutically attractive Auger electron emitters with notably high Auger electron yield per decay. The present paper summarizes the first step of research on the applications of core-shell (Au@Pt) nanoparticles for electron Auger therapy of HER2+ (human epidermal growth factor receptor 2) breast cancer and hepatocellular carcinoma. Gold nanoparticles (30 nm) were synthesized covered with a platinum shell at high efficiency (>80%) and were further evaluated for in vitro studies such as binding affinity, internalization and cytotoxicity. To find the mechanism(s) responsible for platinum cytotoxicity in HepG2 cells, the platinum concentration in isolated cell nuclei and cytoplasm was determined using ICP-MS (inductively coupled plasma mass spectrometry). Lack of platinum in cell nuclei suggests that the cytotoxic effect is associated with the generation of reactive oxygen species (ROS) and reactive nitrogen species (RNS). Studies carried out on the SKOV-3 cell line with the use of a synthesized targeting bioconjugate (Au@Pt-PEG-trastuzumab) revealed a high affinity of this preparation to HER2+ cells, its internalization, its placement in the perinuclear area and partial intranuclear location. The specific binding for HER2 negative cells, MDA-MB-231, was negligible and Au@Pt-PEG-trastuzumab did not enter these cells. The results obtained are promising and warrant future investigation of Auger electron therapy using ^193mPt and ^195mPt based radiopharmaceuticals.     

Thermally Stable and Regenerable Platinum–Tin Clusters for Propane Dehydrogenation Prepared by Atom Trapping on Ceria

Ceria (CeO₂) supports are unique in their ability to trap ionic platinum (Pt), providing exceptional stability for isolated single atoms of Pt. The reactivity and stability of single‐atom Pt species was explored for the industrially important light alkane dehydrogenation reaction. The single‐atom Pt/CeO₂ catalysts are stable during propane dehydrogenation, but are not selective for propylene. DFT calculations show strong adsorption of the olefin produced, leading to further unwanted reactions. In contrast, when tin (Sn) is added to CeO₂, the single‐atom Pt catalyst undergoes an activation phase where it transforms into Pt–Sn clusters under reaction conditions. Formation of small Pt–Sn clusters allows the catalyst to achieve high selectivity towards propylene because of facile desorption of the product. The CeO₂‐supported Pt–Sn clusters are very stable, even during extended reaction at 680 °C. Coke formation is almost completely suppressed by adding water vapor to the feed. Furthermore, upon oxidation the Pt–Sn clusters readily revert to the atomically dispersed species on CeO₂, making Pt–Sn/CeO₂ a fully regenerable catalyst.     

Effect of Ru addition on the structural characteristics and the electrochemical activity for ethanol oxidation of carbon supported Pt–Sn alloy catalysts

Binary Pt–Sn/C (1:1) and ternary Pt–Sn–Ru/C (1:1:0.3 and 1:1:1) catalysts were synthesized by reduction of precursors with formic acid, and their activity for ethanol oxidation was compared with that of commercial Pt/C and Pt–Ru/C catalysts. Linear sweep voltammetry measurements at 40 and 90 °C showed that for potentials higher than 0.3 V vs. RHE, the Pt–Sn–Ru/C (1:1:0.3) catalyst presents the highest activity for ethanol electro-oxidation, while the electrochemical activity of the Pt–Sn–Ru/C (1:1:1) catalyst was lower than that of both the binary Pt–Sn/C and Pt–Ru/C catalysts. Tests in a single direct ethanol fuel cell confirmed the superior performance of the Pt–Sn–Ru/C (1:1:0.3) electrocatalyst. The positive effect of the Ru presence in the Pt–Sn–Ru/C (1:1:0.3) catalyst was ascribed to the interactions between Sn and Ru oxides.     

195Pt, 119Sn and 31P NMR studies of alkyl,aryl and acyl trichlorostannate complexes of platinum(II). The crystal structure of trans-[Pt(SnCl3)(COC6H5)(PEt3)2]

¹⁹⁵Pt, ¹¹⁹Sn and ³¹P NMR characteristics of the complexes trans-[Pt(SnCl₃)(carbon ligand)(PEt₃)₂] (1a-1e) are reported, (carbon ligand = CH₃ (1a), CH₂Ph (1b), COPh (1c), C₆Cl₅ (1d), C₆Cl₄Y (e); Y = meta- and para-NO₂, CF₃, Br, H, CH₃, OCH₃, or Pt(SnCl₃)(PEt₃)₂. The values of ¹J(¹⁹⁵Pt, ¹¹⁹Sn) vary from 2376 to 11895 Hz with the COPh ligand having the smallest and the C₆Cl₅ ligand the largest value, making a total range for this coupling constant, when the dimer syn-trans-[PtCl(SnCl₃)(PEt₃)]₂ is included, of ca. 33000 Hz. In the meta- and para-substituted phenyl complexes ¹J(¹⁹⁵Pt, ¹¹⁹Sn) (a) is greater for electron-withdrawing substituents, (b) varies more for the meta-substituted derivatives (5634 to 7906 Hz) than for the para analogues (6088 to 7644 Hz) and (c) has the lowest values when the Pt(SnCl₃)(PEt₃)₂ group is the meta- or para-substituent. The direction of the change in ¹J(¹⁹⁵Pt, ¹¹⁹Sn) is opposite to that found for ¹J(¹⁹⁵Pt, ¹¹⁹P). For the aryl complexes linear correlations are observed between δ(¹¹⁹Sn), ¹J(¹⁹⁵Pt, ¹¹⁹Sn), ¹J(¹⁹⁵Pt, ³¹P), ¹J(¹¹⁹Sn, ³¹P) and the Hammett substituent constant σⁿ. δ(¹¹⁹Sn) and ¹J(¹⁹⁵Pt, ¹¹⁹Sn) are related linearly to v(Pt-H) in the complexes trans-[PtH(C₆H₄Y)(PEt₃)₂]; δ(¹¹⁹Sn) and δ(¹H) (hydride) are also linearly related. Based on ¹J(¹⁹⁵Pt, ¹¹⁹Sn), the acyl ligand is suggested to have a very large NMR trans influence. The differences in the NMR parameters for (1a-e) are rationalized in terms of differing σ- and π-bonding abilities of the carbon ligands.The structure of 1c has been determined by crystallographic methods. The complex has a slightly distorted square planar geometry with trans-PEt₃ ligands. Relevant bond lengths (Å) and bond angles (°) are: PtSn, 2.634(1), PtP, 2.324(4) and 2.329(4), PtC, 2.05(1); PPtP, 170.7(6), SnPtC, 173.0(3), SnPtP, 92.1(1), 91.7(1), PPtC, 88.8(4) and 88.3(4). The PtSn bond separation is the longest yet observed for square-planar platinum trichlorostannate complexes, and would be consistent with a large crystallographic trans influence of the benzoyl ligand. The PtSn bond separation is shown to correlate with ¹J(¹⁹⁵Pt, ¹¹⁹Sn).     

Separation of113mIn from113Sn on an isotope generator with inorganic ionite

A method of preparation of hydrated zirconium oxide suitable for^113mIn generators was elaborated. A good separation of^113mIn from¹¹³Sn was obtained in the course of routine use of generator, with a very small admixture of zirconium in the eluate.     

113Sn-113mIn generator with a glass beads column

The adsorption characteristics of ¹¹³Sn(IV) and ^113mIn(III) on glass beads from NaCl solutions have been studied. On the basis of these studies, ¹¹³Sn-^113mIn generator has been prepared by adsorbing ¹¹³Sn on the glass beads column. ^113mIn has been eluted by the 0.16M NaCl solution with pH 3.0, remaining ¹¹³Sn adsorbed on the glass beads. The yield of ^113mIn has been about 73% in the first 6 ml of eluate, while the breakthrough of ¹¹³Sn has been about 0.042%.     

Thermally Stable and Regenerable Platinum–Tin Clusters for Propane Dehydrogenation Prepared by Atom Trapping on Ceria

Ceria (CeO₂) supports are unique in their ability to trap ionic platinum (Pt), providing exceptional stability for isolated single atoms of Pt. The reactivity and stability of single-atom Pt species was explored for the industrially important light alkane dehydrogenation reaction. The single-atom Pt/CeO₂ catalysts are stable during propane dehydrogenation, but are not selective for propylene. DFT calculations show strong adsorption of the olefin produced, leading to further unwanted reactions. In contrast, when tin (Sn) is added to CeO₂, the single-atom Pt catalyst undergoes an activation phase where it transforms into Pt–Sn clusters under reaction conditions. Formation of small Pt–Sn clusters allows the catalyst to achieve high selectivity towards propylene because of facile desorption of the product. The CeO₂-supported Pt–Sn clusters are very stable, even during extended reaction at 680 °C. Coke formation is almost completely suppressed by adding water vapor to the feed. Furthermore, upon oxidation the Pt–Sn clusters readily revert to the atomically dispersed species on CeO₂, making Pt–Sn/CeO₂ a fully regenerable catalyst.     

Zirconium silicotungstate matrix as a prospective sorbent material for the preparation of <Superscript>113</Superscript>Sn/<Superscript>113m</Superscript>In generator

The zirconium silicotungstate (ZrSiW) was studied as an effective sorbent material to be used in the ¹¹³Sn/^113mIn generator. The results elucidated that the distribution coefficient of ¹¹³Sn (3700 mL/g) is greater than ^113mIn (275 mL/g) from 0.1 M HCl acid solution to the ZrSiW material. The maximum sorption capacity of Sn (IV) was found to be 33 mg per gram ZrSiW (~?0.3 mmol/g). The elution yield of ^113mIn was found to be >?78?±?6.4% with an acceptable purity of radionuclidic and radiochemical (≥?99.99 and 96.8%, respectively). The rigorous separation of ^113mIn from the ¹²⁵Sb was carried out due to its long half-life (2.758 years) and beta emission that causes tissue damage. Zr, W and Si levels are below the permitted limit in the ^113mIn eluate.     

Cross-sections for formation of 195mPt through natPt(n,x)195mPt reaction over neutron energy range 13–15 MeV

The cross-sections for formation of metastable state of ¹⁹⁵Pt (^195mPt, 98.85 keV, 4.02 d) through ^natPt(n,x)^195mPt reaction induced by 13.5–14.6 MeV neutrons were measured. Measurements were corrected for gamma-ray attenuations, random coincidence (pile-up), dead time and fluctuation of neutron flux. The data for ^natPt(n,x)^195mPt reaction cross-sections are reported to be 438±46, 399±44 and 372±43 mb at 13.5±0.2, 14.1±0.1 and 14.6±0.2 MeV incident neutron energies, respectively.     

Radiochemical studies on generator eluted113mIn chloride

^113mIn is milked out of a¹¹³Sn-^113mIn generator with dilute hydrochloric acid for use in nuclear medicine. The concentrations of the various impurities like Sn, Zr and their colloidal forms which may trap^113mIn activity have to be initially evaluated before releasing the generator for medicinal use. The authors have evaluated the purity of the^113mIn-chloride obtained from the generators in detail. The possibility of using a mixture of HCl and NaCl as an alternative eluent for^113mIn has also been investigated. It has been observed that this new eluent gives greater yields of^113mIn and renders the final manipulation of isotonicity of indium labelled compounds easy.     

Accurate prediction of 195Pt-NMR chemical shifts for hydrolysis products of [PtCl6]2− in acidic and alkaline aqueous solutions by non-relativistic DFT computational protocols

The ¹⁹⁵Pt-NMR chemical shifts of all possible hydrolysis products of [PtCl₆]^2? in acidic and alkaline aqueous solutions are calculated employing simple non-relativistic density functional theory computational protocols. Particularly, the GIAO-PBE0/SARC-ZORA(Pt) ∪ 6-31 + G(d)(E) computational protocol augmented with the universal continuum solvation model (SMD) performs the best for calculation of the ¹⁹⁵Pt-NMR chemical shifts of the Pt(IV) complexes existing in acidic and alkaline aqueous solutions of [PtCl₆]^2?. Excellent linear plots of δ_calcd(¹⁹⁵Pt) chemical shifts versus δ_exptl(¹⁹⁵Pt) chemical shifts and δ_calcd(¹⁹⁵Pt) versus the natural atomic charge Q_Pt are obtained. Very small changes in the Pt–Cl and Pt–O bond distances of the octahedral [PtCl₆]^2?, [Pt(OH)₆]^2?, and [Pt(OH₂)₆]⁴⁺ complexes have significant influence on the computed σ^{iso 195}Pt magnetic shielding tensor elements of the anionic [PtCl₆]^2? and the computed δ ¹⁹⁵Pt chemical shifts of [Pt(OH)₆]^2? and [Pt(OH₂)₆]⁴⁺. An increase of the Pt–Cl and Pt–O bond distances by 0.001 Å (1 mÅ) is accompanied by a downfield shift increment of 17.0, 19.4, and 37.6 ppm mÅ^?1, respectively. Counter-anion effects in the case of the highly positive charged complexes drastically improve the accuracy of the calculated ¹⁹⁵Pt chemical shifts providing values very close to the experimental ones.     

Etude des generateurs d'indium-113m

Methods are proposed for the determination of¹¹³Sn in the eluate of an^113mIn generator as well as for the analysis of its chemical and radionuclidic purity. Two generators of different origin have been studied. The presence of the radioisotopes¹¹³Sn,¹²⁵Sb,^125mTe and the elements Zr, Si and Fe have been found in the eluate. Recommendations are given for the use of such generators.     

Low Pt content Pt–Ru–Ir–Sn quaternary catalysts for anodic methanol oxidation in DMFC

In this communication we report our research work on low Pt content Pt–Ru–Ir–Sn quaternary catalysts for use in DMFC anodes. The carbon-supported quaternary metal alloy catalyst was synthesized according to the solution reduction method and was deposited onto a carbon fiber paper or a carbon aerogel nanofoam to form the anode for direct methanol fuel cells. The Pt loading of the electrode is 0.1 mg/cm². The testing results from a three-electrode electrochemical cell show that the simultaneous use of higher Ir (25–35 wt.%) and Sn (10 wt.%) content gives satisfactory stability and higher activity for methanol oxidation than the commercially available E-TEK anode (80%[0.5Pt 0.5Ru]/C on carbon cloth). Energy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), scanning electron microscope (SEM), and Bruner–Emmett–Teller method (BET) measurements were carried out to characterize the composition, structure, morphology, and surface area of the developed catalysts.     

Development of new <Superscript>116</Superscript>Cd/Pt target for cyclotron produced <Superscript>117m</Superscript>Sn as a medical radiometal

The radioisotope ^117mSn has recently attracted considerable attention because of its application in theranostics and its imaging using 159-keV γ-photons. In this study, we developed a target system that yielded ^117mSn via a ¹¹⁶Cd(α, 3n)^117mSn nuclear reaction. A separable Pt substrate was utilized to prepare the enriched ¹¹⁶Cd target to be irradiated, and the enriched ¹¹⁶Cd in a cadmium acetate solution was electroplated onto the Pt substrate. The substrate was thermally analyzed via ANSYS simulations, and the plating thickness was optimized through calculations with TALYS code. The production of ^117mSn was confirmed through the emission measurement of inherent gamma rays.     

Structural characteristics of the coordination nodes of the anticarcinogenic dimeric complex di-μ-guanine-bis[cis-dichloroaquoplatinum(II)] in the crystalline tetrahydrate

Structural characteristics of coordination nodes in the anticarcinogenic crystalline hydrate of the di-μ-guanine-bis-[cis-dichloroaquoplatinum(II)] dimeric complex were investigated by IR, NMR (¹H,¹³C, and¹⁹⁵Pt), and EXAFS methods. The guanine molecules in the keto form of the complex bridge the platinum atoms by the head-to-tail principle, and the coordination nodes are polyhedra of pentaccordinated platinum(II), PtCl₂NO₂, with the distances R(Pt?Cl)=2.44 Å and R(Pt?N(O))=2.06 Å. The distances from the platinum atom to the nearest atoms not chemically bonded to the metal are R(Pt?C)=2.86 Å and R(Pt?Pt)=5Å.     

NMR in powders and single crystals of the metal-alloy cluster [HNi38Pt6(CO)48]5-

The 44 atom core Ni38Pt6 in the metal cluster compound [HNi₃₈Pt₆(CO)₄₈]^5- is the largest metal atom core, that has been realized in a single crystal. By ¹⁹⁵Pt NMR we have studied the electron density at the Pt-core atoms in powders and single crystals of two varieties of this compound. The large line widths can be explained by charge fluctuations between the metal cores, which are about 17 Å apart. The relaxation rates, which resemble those in randomly-packed Pt309 cluster compounds, confirm such an interpretation.     

Dünnschichtchromatographie als Hilfsmittel in der Radiochemie. 4. Mitteilung Trennung von 113Sn und 113mIn

Thin-layer chromatography is applied to the separation of ^113mIn from ¹¹³Sn. Different factors influencing migration and separation of the ions are investigated. The method can be used for the examination of the purity of isolated ^113mIn solutions.     

Electrocatalysts for methanol oxidation with ultra low content of Pt and Ru

We have developed efficient electrocatalysts for methanol oxidation using new synthetic method facilitating deposition of Pt–Ru very thin nanoplatelets on carbon nanoparticles The method involves oxidation of carbon support, adsorption of Pb²⁺, its reduction and galvanic displacement of Pb⁰ by Pt and/or Ru. The Pt mass activity of this catalyst is about 10 times higher than that of the commercial Pt–Ru/C. The catalyst with the 1:1 Pt/Ru ratio displayed the highest methanol oxidation activity per surface Pt atom. Our results demonstrate the new synthetic method that yields the catalyst with potential for solving the problem of high Pt loading in direct methanol fuel cell anodes.     

Separation of <Superscript>113m</Superscript>In from <Superscript>113</Superscript>Sn based on activated carbon used as column matrix

The activated carbon was prepared by using corncobs and characterized by sorpatometer for using as an exchanger material to separate the generated ^113mIn from ¹¹³Sn and ^124,125Sb. To optimize the separation process, the different parameters like acetone percentage, HCl concentration were studied. The exchange capacity of Sn(IV) is 7.6 meq/g onto the activated carbon and the elution efficiency of ^113mIn > 80% by using 10 mL of 0.2 M HCl-80% acetone with flow rate 1 mL/min. The radionuclidic purity and radiochemical purity of the eluted ^113mIn were examined and clarified the presence of ^124,125Sb with relatively high level as radio impurities, so further separation was carried out by using Dowex 1×8 as an anion exchanger below the activated carbon matrix on the same separation column to adsorb the ¹¹³Sn and ^124,125Sb, which escape from the activated carbon matrix.