The optical properties and energy transition process in nanocomposite of polyvinyl-pyrrolidone polymer and Mn-doped ZnS

This study has been carried out on the optical properties of polyvinyl-pyrrolidone (PVP), the energy transition process in nanocomposite of PVP capped ZnS:Mn nanocrystalline and the influence of the PVP concentration on the optical properties of the PVP capped ZnS:Mn nanocrystalline thin films synthesized by the wet chemical method. The microstructures of the samples were investigated by X-ray diffraction, the atomic absorption spectroscopy, and transmission electron microscopy. The results showed that the prepared samples belonged to the sphalerite structure with the average particle size of about 2–3 nm. The optical properties of samples are studied by measuring absorption, photoluminescence (PL) spectra and time-resolved PL spectra in the wavelength range from 200 to 700 nm at 300 K. From data of the absorption spectra, the absorption edge of PVP polymer was found about of 230 nm. The absorption edge of PVP capped ZnS:Mn nanoparticles shifted from 322 to 305 nm when the PVP concentration increases. The luminescence spectra of PVP showed a blue emission with peak maximum at 394 nm. The luminescence spectra of ZnS:Mn–PVP exhibits a blue emission with peak maximum at 437 nm and an orange–yellow emission of ion Mn²⁺ with peak maximum at 600 nm. While the PVP coating did not affect the microstructure of ZnS:Mn nanomaterial, the PL spectra of the PVP capped ZnS:Mn samples were found to be affected strongly by the PVP concentration.     

Strong green luminescence of Ni2+-doped ZnS nanocrystals

ZnS nanoparticles doped with Ni²⁺ have been obtained by chemical co-precipitation from homogeneous solutions of zinc and nickel salt compounds, with S^2- as precipitating anion, formed by decomposition of thioacetamide (TAA). The average size of particles doped with different mole ratios, estimated from the Debye–Scherrer formula, is about 2–2.5 nm. The nanoparticles could be doped with nickel during synthesis without altering the X-ray diffraction pattern. A Hitachi M-850 fluorescence spectrophotometer reveals the emission spectra of samples. The absorption spectra show that the excitation spectra of Ni-doped ZnS nanocrystallites are almost the same as those of pure ZnS nanocrystallites (λ_ex=308–310 nm). Because a Ni²⁺ luminescent center is formed in ZnS nanocrystallites, the photoluminescence intensity increases with the amount of ZnS nanoparticles doped with Ni²⁺. Stronger and stable green-light emission (520 nm) (its intensity is about two times that of pure ZnS nanoparticles) has been observed from ZnS nanoparticles doped with Ni²⁺. Received: 18 December 2000 / Accepted: 17 March 2001 / Published online: 20 June 2001     

Synthesis and photoluminescent and nonlinear optical properties of manganese doped ZnS nanoparticles

In this work we synthesized ZnS:Mn²⁺ nanoparticles by chemical method using PVP (polyvinylpyrrolidone) as a capping agent in aqueous solution. The structure and optical properties of the resultant product were characterized using UV-vis optical spectroscopy, X-ray diffraction (XRD), photoluminescence (PL) and z-scan techniques. UV-vis spectra for all samples showed an excitonic peak at around 292 nm, indicating that concentration of Mn²⁺ ions does not alter the band gap of nanoparticles. XRD patterns showed that the ZnS:Mn²⁺ nanoparticles have zinc blende structure with the average crystalline sizes of about 2 nm. The room temperature photoluminescence (PL) spectrum of ZnS:Mn²⁺ exhibited an orange-red emission at 594 nm due to the ⁴T₁-⁶A₁ transition in Mn²⁺. The PL intensity increased with increase in the Mn²⁺ ion concentration. The second-order nonlinear optical properties of nanoparticles were studied using a continuous-wave (CW) He-Ne laser by z-scan technique. The nonlinear refractive indices of nanoparticles were in the order of 10⁻⁸ cm²/W with negative sign and the nonlinear absorption indices of these nanoparticles were obtained to be about 10⁻³ cm/W with positive sign.     

Large two-photon absorbance of chitosan–ZnS quantum dots nanocomposite film

ZnS semiconductor nanoparticles with average size of 3.4 nm were prepared in situ in chitosan film. TEM, UV–vis spectra and PL spectra show the ZnS nanoparticles in chitosan template were monodispersed and well passivated. The two-photon absorption coefficient (β) of the chitosan–ZnS quantum dots (QDs) nanocomposite film was obtained to be 2.29×10² cm/Gw from a standard Z-scan setup with femtosecond laser pusles at 790 nm wavelength. Results show the novel biomacromolecule/QDs nanocomposite film has large third-order optical nonlinear absorption, the mechanism responsible for which was discussed.     

Highly luminescent undoped and Mn-doped ZnS nanoparticles by liquid phase pulsed laser ablation

In this paper we report the synthesis of highly luminescent ZnS and Mn-doped ZnS nanoparticles with uniform particle size distribution by liquid phase pulsed laser ablation. The formation of nanosized ZnS crystallites was confirmed by high-resolution transmission electron microscopy (HRTEM) images. The optical properties of these nanoparticles were studied by room temperature photoluminescence (PL) spectra. The PL emission from the ZnS nanoparticles shows a sharp peak in the UV region (334 nm) corresponding to the band edge and a broad peak in the visible region which can be attributed to the sulphur vacancies, cation vacancies and surface states in the nanocrystals. The yellow emission from the Mn-doped ZnS nanoparticles can be attributed to the radiative transition between ⁴T₁ and ⁶A₁ levels within the 3d⁵ orbital of Mn²⁺.     

Spectroscopy of Nickel-Doped Zinc Sulfide Nanoparticles

ABSTRACT

In the present study, Zn_1?xNi_xS (x = 0.0–0.8 mol%) nanoparticles were prepared through the chemical route and the synthesis involved the mixing and drying of zinc acetate and sodium sulphide in an appropriate ratio with the addition of Ni²⁺ at a proper concentration. The structural and spectroscopic studies are investigated by X-ray diffraction (XRD), absorption spectra, emission and excitation spectra, and Raman spectra. Compared with that of the pristine materials, the absorption band-edge demonstrates an apparently blue shift, which is attributed to the quantum size effect. The average particle size of ZnS nanoparticles is in the range of 2–4 nm deduced from the XRD line broadening. Excited at about 330 nm, a blue emission band at 425 nm can be observed, which corresponds to Ni²⁺ luminescent center; this result is consistent with the postulation that Ni²⁺ replaced the Zn²⁺ ions in the lattice of ZnS nanocrystals. Excitation spectra also confirm the above postulation. The effect of different concentrations of nickel is also studied by Raman spectra.     

Photoluminescence characteristics of ZnS nanocrystallites doped with Ti3+and Ti4+

Direct synthesis of ZnS nanocrystallites doped with Ti³⁺ or Ti⁴⁺ by precipitation has led to novel photoluminescence properties. Detailed X-ray diffraction (XRD), fluorescence spectrophotometry, UV–vis spectrophotometry and X-ray photoelectron spectroscopy (XPS) analysis reveal the crystal lattice structure, average size, emission spectra, absorption spectra and composition. The average crystallite size doped with different mole ratios, estimated from the Debye–Scherrer formula, is about 2.6±0.2 nm. The nanoparticles can be doped with Ti³⁺ and Ti⁴⁺ during the synthesis without the X-ray diffraction pattern being altered. The strong and stable visible-light emission has been observed from ZnS nanocrystallites doped with Ti³⁺ (its maximum fluorescence intensity is about twice that of undoped ZnS nanoparticles). However, the fluorescence intensity of the ZnS nanocrystallites doped with Ti⁴⁺ is almost the same as that of the undoped ZnS nanoparticles. The emission peak of the undoped sample is at 440–450 nm. The emission spectrum of the doped sample consists of two emission peaks, one at 420–430 nm and the other at 510 nm. Received: 27 April 2001 / Accepted: 16 August 2001 / Published online: 17 October 2001     

Photoluminescent properties of ZnS nanoparticles prepared by electro-explosion of Zn wires

We study the photoluminescent properties of ZnS nanoparticles without the influence of dopants or magnetic impurities. The ZnS nanoparticles reported in this case were synthesized by a novel method of electro-explosion of wire (EEW). The nanoparticles were prepared employing electro-explosion of pure zinc wires in a cell filled with sulfide ions to produce a free-standing compound ZnS semiconductor. To investigate the structural and optical properties, these nanoparticles were characterized by X-ray powder diffraction (XRD), atomic force microscopy (AFM), UV–visible and photoluminescence (PL) spectroscopy. Consistent with the enhancement of the PL intensity of the 443 nm peak due to deep blue emission of ZnS particles, the XRD of the nanoparticles reveals a hexagonal phase of ZnS nanocrystallites prepared by our novel synthesis technique.      

Synthesis of high quality and monodisperse CdS:Mn/ZnS and CdS:Mn/CdS core–shell nanoparticles

CdS:Mn²⁺/ZnS and CdS:Mn²⁺/CdS core–shell nanoparticles were synthesized in aqueous medium via chemical precipitation method in an ambient atmosphere. Polyvinylpyrrolidone (PVP) was used as a capping agent. The effect of the shell (ZnS and CdS) thickness on CdS:Mn²⁺ nanoparticles was investigated. Inorganically passivated core/shell nanocrystals having a core (CdS:Mn²⁺) diameter of 4 nm and a ZnS-shell thickness of ∼0.5 nm exhibited improved PL intensity. Optimum concentration of doping ions (Mn²⁺) was selected through optical study. For all the core–shell samples two emission peaks were observed, the first one is band edge emission in the lower wavelength side due to energy transfer to the Mn²⁺ ions in the crystal lattice; the second emission is characteristic peak of Mn²⁺ ions (⁴T₁ → ⁶A₁). The XRD, TEM and PL results showed that the synthesized core–shell particles were of high quality and monodisperse.     

Structural and optical characterization of ZnS nanoparticles co-doped with Mn and Te

Nanoparticles of Zinc sulfide co-doped with equal atomic percentages of Mn and Te (5, 10 and 15 at%) were synthesized for the first time by chemical co-precipitation method. Thiophenol was used to passivate the surface of the particles. The as-prepared samples were amorphous in nature and nano-crystallinity was induced after calcining at 300 °C/2 h. The nanoparticles were characterized by EDAX, XRD, TEM, optical absorption and PL studies. EDAX spectra revealed only minor deviations of the dopant concentrations from the target compositions. The nanoparticles showed cubic structure. The particle size estimated from XRD/TEM was in the range 3–5 nm. Optical absorption studies showed a blue-shift of the fundamental absorption edge with respect to that of bulk ZnS. PL spectra showed emission in the red region with composition dependent emission wavelength. ZnS nanoparticles doped with Mn (5 and 10 at%) were also synthesized and characterized for comparison.     

Synthesis and characterization of Cu doped ZnS nanoparticles using TOPO and SHMP as capping agents

Undoped and Cu²⁺ doped (0.2-0.8%) ZnS nanoparticles have been synthesized through chemical precipitation method. Tri-n-octylphosphine oxide (TOPO) and sodium hexametaphosphate (SHMP) were used as capping agents. The synthesized nanoparticles have been analyzed using X-ray diffraction (XRD), transmission electron microscope (TEM), Fourier transform infrared spectrometer (FT-IR), UV-vis spectrometer, photoluminescence (PL) and thermo gravimetric-differential scanning calorimetry (TG-DTA) analysis. The size of the particles is found to be 4-6 nm range. Photoluminescence spectra were recorded for ZnS:Cu²⁺ under the excitation wavelength of 320 nm. The prepared Cu²⁺-doped sample shows efficient PL emission in 470-525 nm region. The capped ZnS:Cu emission intensity is enhanced than the uncapped particles. The doping ions were identified by electron spin resonance (ESR) spectrometer. The phase changes were observed in different temperatures.     

Synthesis, characterization and optical properties of water-soluble ZnS:Mn nanoparticles

ZnS nanoparticles with Mn²⁺ doping (0.5-20%) have been prepared through a simple chemical method, namely the chemical precipitation method. The structure of the nanoparticles has been analyzed using X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM) and UV-vis spectrometer. The size of the particles is found to be 3-5 nm range. Photoluminescence spectra were recorded for undoped ZnS nanoparticles using an excitation wavelength of 320 nm, exhibiting an emission peak centered at around 445 nm. However, from the Mn²⁺-doped samples, a yellow-orange emission from the Mn²⁺⁴T₁-⁶A₁ transition is observed along with the blue emission. The prepared Mn²⁺-doped sample shows efficient emission of yellow-orange light with the peak emission 580 nm with the blue emission suppressed. The maximum PL intensity is observed only at the excitation energy of 3.88 eV (320 nm). Increase in stabilizing time up to 48 h in de-ionized water yields the enhancement of emission intensity of doped (4% Mn²⁺) ZnS. The correlation made through the concentration of Mn²⁺ versus PL intensity resulted in opposite trend (mirror image) of blue and yellow emissions.     

A study on optical,photoluminescence and thermoluminescence properties of ZnO and Mn doped-ZnO nanocrystalline particles

Pure ZnO and Mn (1%wt.) doped-ZnO nanocrystalline particles were synthesized by reverse micelle method. The structural properties of the nanoparticles were investigated by X-Ray Diffraction (XRD) and Transmission Electron Microscopy (TEM) techniques. UV–vis and photoluminescence (PL) spectroscopy was used for analyzing the optical properties of the nanoparticles. XRD and TEM results revealed the formation of ZnO and Mn doped-ZnO nanocrystalline particles with pure wurtzite crystal structure and average particle size of 18–21 nm. From UV–vis studies, the optical band gap energy of 3.53 and 3.58 eV obtained for ZnO and Mn doped-ZnO nanoparticles, respectively. Further optical analysis showed that the refractive index decreases from 2.35 to 1.35 with the change of wavelength. Room-temperature photoluminescence analysis of all samples showed four main emission bands including a strong UV emission band, a weak blue band, a week blue–green band, and a weak green band which indicated their high structural and optical quality. Moreover, the samples exposed to gamma rays sources of ¹³⁷Cs and ⁶⁰Co and their thermoluminescence properties were investigated. The thermoluminescence response of ZnO and Mn doped-ZnO nanocrystalline particles as a function of dose exhibited good linear ranges, which make them very promising detectors and dosimeters suitable for ionizing radiation.     

Mechano-chemical synthesis and optical properties of ZnS nanoparticles

In the present work, we report the synthesis and optical properties of ZnS nanoparticles produced by the mechano-chemical route. We used zinc acetate and sodium sulphide as source materials in a high energy planetary ball mill at rotation speed of 300 rpm and vial rotation speed of 600 rpm with ball to powder (BPR or charge ratio CR) 5:1 for 30 and 90 min. The milled powders were washed with methanol to remove impurity and dried at 300 °C for 1 h. The prepared nanoparticles have been characterized using X-ray diffraction (XRD), Field emission scanning electron microscope (FESEM), UV–vis–NIR spectrophotometer and Fluorescence spectroscopy. The crystallite size of the synthesized ZnS nanoparticles is found to be in the range 7–8 nm which was calculated using Debye–Scherer's formula. The value of optical band gap has been found to be in the range 3.80–4.15 eV. Room temperature photoluminescence (PL) spectrum of ZnS samples exhibit a blue emission peaked at 466 nm under UV excitation.     

The influence of annealing temperature on the structure,morphologies and optical properties of ZnO nanoparticles

ZnO nanoparticles (NPs) have been successfully synthesized by the simple solution method at low temperature. The effects of annealing temperature on the structure and optical properties of ZnO NPs were investigated in detail by X-ray diffraction, transmission electron microscopy (TEM), ultraviolet–visible (UV–vis) spectroscopy and photoluminescence (PL) measurements. As the annealing temperature was increased above 180 ^°C the particles morphology evolved from spherical to hexagonal shape, indicating that the average particle size increased from 11 nm to 87 nm. The UV-vis and PL spectra showed a red-shift from 3.62 to 3.33 eV when the annealing temperature was increased.     

Synthesis,structural, optical,and magnetic properties of Co doped,Sm doped and Co+Sm co-doped ZnS nanoparticles

The compositional, structural, optical and magnetic properties of ZnS, Zn_0.98Co_0.02S, Zn_0.98Sm_0.02S and Zn_0.96Co_0.02Sm_0.02S nanoparticles synthesized by a hydrothermal method are presented and discussed. X-ray diffraction (XRD), high resolution transmission electron microscopy (HRTEM) and selected area electron diffraction (SAED) studies revealed that all the samples exhibited cubic structure without any impurity phases. X-ray photoelectron spectroscopy (XPS) results revealed that the Co and Sm ions existed in +2 and +3 states in these samples. The photoluminescence (PL) spectra of all the samples exhibited a broad emission in the visible region. The room temperature magnetization versus applied magnetic field (M–H) curves demonstrated that the Sm+Co doped nanoparticles exhibited enhanced ferromagnetic behavior compare to Co and Sm individually doped ZnS nanoparticles, which is probably due to the exchange interaction between conductive electrons with local spin polarized electrons on the Co²⁺ or Sm³⁺ ions. This study intensifies the understanding of the novel performances of co-doped ZnS nanoparticles and also provides possibilities to fabricate future spintronic devices.     

Preparation, characterization and study of optical properties of ZnS nanophosphor

In this work the preparation, characterization and photoluminescence studies of pure and copper-doped ZnS nanophosphors are reported, which are prepared by using solid-state reaction technique at a temperature of 100 °C. The as-obtained samples were characterized by X-ray diffraction (XRD) and UV-VIS Reflectance spectroscopy. The XRD analysis confirms the formation of cubic phase of undoped as well as Cu²⁺-doped ZnS nanoparticles. Furthermore it shows that the average size of pure as well as copper-doped samples ranges from 15 to 50 nm. The room-temperature PL spectra of the undoped ZnS sample showed two main peaks centered at around 421 and 450 nm, which are the characteristic emissions of interstitial zinc and sulfur vacancies, respectively. The PL of the doped sample showed a broad-band emission spectrum centered at 465 nm accompanied with shoulders at around 425, 450 and 510 nm, which are the characteristic emission peaks of interstitial zinc, sulfur vacancies and Cu²⁺ ions, respectively. Our experimental results indicate that the PL spectrum confirms the presence of Cu²⁺ ions in the ZnS nanoparticles as expected.     

Effect of surface on the optical structure and thermal properties of organically capped CdS nanoparticles

Cadmium sulfide (CdS) nanoparticles were synthesized by a novel wet chemical route with various organic thiol stabilizers. Systematic experimental studies, including X-ray diffraction (XRD), ultraviolet–visible (UV–vis) spectroscopy, Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), photoluminescence (PL) spectroscopy, and time-resolved photoluminescence (TRPL), have evidenced that the stability, crystallinity, and optical properties of the CdS nanoparticles are affected by the organic groups which generate significant effects in surface reconstruction. Particle size was evaluated from UV–vis spectroscopy using the effective mass approximation (EMA) method and from XRD patterns based on Scherrer?s formula. The S–H vibrations are not detectable in the infrared (IR) spectra of any of the bound ligands, which are expected for thiols covalently bound to the surface of nanoparticles. PL studies reveal that the emission from the nanostructures is not much influenced by the surface states, indicating a good passivation of the particle?s surface. The time-resolved measurements reveal a biexponential decay behavior. The fast decay component is attributed to the recombination of core states, while the slow decay component of PL is associated with the charge-carrier recombination process with the involvement of surface states.     

Synthesis and photoluminescence of water-soluble Mn-doped ZnS quantum dots

The water-soluble Mn²⁺-doped ZnS quantum dots (Mn:ZnS d-dots) were synthesized by using thioglycolic acid (TGA) as stabilizer in aqueous solutions in air, and characterized by X-ray powder diffraction (XRD), UV-vis absorption spectra and photoluminescence (PL) emission spectroscopy. The sizes of Mn:ZnS d-dots were determined to be about 2 nm using XRD measurements and the UV-vis absorption spectra. It was found that the Mn²⁺⁴T₁ → ⁶A₁ emission intensity of Mn:ZnS d-dots significantly increased with the increase of Mn²⁺ concentration, and showed a maximum when Mn²⁺ doping content was 1.5%. If Mn²⁺ concentration continued to increase, namely more than 1.5%, the Mn²⁺⁴T₁ → ⁶A₁ emission intensity would decrease. In addition, the effects of TGA/(Zn + Mn) molar ratio on PL were investigated. It was found that the peak intensity ratio of Mn²⁺⁴T₁ → ⁶A₁ emission to defect-states emission showed a maximum when the TGA/(Zn + Mn) molar ratio was equal to 1.8.     

核壳结构CdS/ZnS纳米微粒的制备与光学特性

用微乳液法制备CdS纳米微粒 ,以ZnS对其进行表面修饰 ,得到具有核壳结构的CdS/ZnS纳米微粒 .采用X射线衍射 (XRD)、透射电镜 (TEM )表征其结构、粒度和形貌 ,紫外 可见吸收光谱 (UV)、光致发光光谱(PL)表征其光学特性 .制得的CdS近似呈球形 ,直径为 3.3nm ;以XRD和UV证实了CdS/ZnS核壳结构的实现 .研究了不同ZnS壳层厚度对CdS纳米微粒光学性能的影响 ,UV谱表明随着壳层厚度的增加纳米微粒的吸收带边有轻微的红移 ,同时短波吸收增强 ;PL谱表明壳层ZnS的包覆可减少CdS纳米微粒的表面缺陷 ,带边直接复合发光的几率增大 ,具有合适的壳层厚度时发光效率大大提高 .