孔雀石绿在镁铝水滑石负载纳米氧化锌上的快速光降解

用共沉淀法制备Mg-Al水滑石纳米粉,ZnO纳米颗粒均相地覆盖在Mg-Al水滑石表面. 在500 ℃煅烧4 h后,采用XRD和SEM分析晶体结构和形貌. 研究表明在Mg-Al水滑石表面成功地制备了纳米ZnO. 所获得的纳米ZnO光催化剂对孔雀石绿表现出高的光催化降解性能. 归因于ZnO表面的高光催化活性以及Mg-Al水滑石较好的吸附性能,其中Mg-Al水滑石层片结构起了重要作用.     

溶胶-凝胶法制备纳米氧化锌及其光催化性能

采用溶胶-凝胶法制备ZnO纳米粒子,采用X-射线衍射仪(XRD)、透射电镜(TEM)等手段对样品进行了表征;以纳米氧化锌作为光催化剂,利用300W高压汞灯为光源对甲基橙溶液进行光催化实验。实验结果表明:以汞灯为光源,纳米ZnO为催化剂对甲基橙溶液进行光催化时,纳米ZnO的最佳投加量为0.1020g。     

原位核磁共振技术研究共催化剂类型以及光照波长对甲醇光催化重整产物的影响

本文采用原位核磁共振的方法研究了在真实固-液环境中共催化剂类型以及光照波长对甲醇光催化重整产物及光解水产氢产率的影响.结果发现,不同贵金属担载的锐钛矿型二氧化钛催化剂对甲醇光催化重整产物的产量和产率有着不同程度的影响,但是对其动力学特征影响不大.光照波长对甲醇光催化重整产物的产量也影响较大.通过对比甲醇氧化产率与产氢产率,发现共催化剂的种类对光催化反应速率及氧化还原能力起重要作用,且共催化剂的种类会影响体系氧化和还原能力之间的协同性.     

真空冷冻干燥结合微乳液法制备纳米ZnO

真空冷冻干燥技术结合反相微乳液法制备了纳米ZnO粉体。利用XRD、TEM及表面积分析仪对制备过程、粉体的结构、形貌、比表面积、孔容进行了表征。探讨了煅烧温度、干燥方式及真空冷冻干燥的主要参数对纳米ZnO的影响。结果表明:该方法较常规方法制备的纳米ZnO粒径小(平均19nm)、分散性好、比表面积大(567.9m2.g-1),对亚甲基蓝溶液的降解(降解率98.6%)具有较高的光催化活性。     

直接Z型CdO-CdS纳米棒阵列的制备及其光电催化性能研究（英文）

本文通过简单的水热法制备了一种CdO-CdS-维纳米棒阵列,并系统地研究了材料的结构、形貌及其光电化学性质和产氢活性.所得纳米棒为直径100至200 nm的六方柱.通过优化煅烧温度和时间得到了该实验条件下光电催化性能最优的样品.在0 V vs.Ag/AgCl偏压下,CdO-CdS光电流密度为6.5mA/cm~2,光电催化产氢活性为240μmol·cm~(-2)·h~(-1),几乎是纯CdS的2倍.该体系的光电催化性能超过了许多己报道的相似体系.根据材料结构和光电化学性能表征结果,提出了直接z型光催化机理,该机理可以很好地解释光致载流子的高分离效率和优异的氧化还原性能.     

氧化锌纳米棒的生长过程研究

利用高分子聚乙烯吡咯烷酮(PVP)和乙酸锌的配合物作为前驱体,在300 ℃温度下煅烧,并制备了氧化锌纳米棒。生成的产物用XRD,TEM,SAED等测试方法进行了表征。为了研究氧化锌纳米棒的生长过程,我们通过控制制备前驱体所需原料的比例不变,改变在300 ℃温度下煅烧的时间,分别为0.5, 3, 12和24 h,来观察生成产物的形貌特征。实验发现在110 ℃温度下干燥的前驱体中已经有氧化锌微晶生成;在300 ℃温度下煅烧0.5 h后就出现了明显的由几个纳米大小的微晶所组成的氧化锌纳米棒;煅烧3 h后的产物是结构非常完整的径直单晶ZnO纳米棒;12和24 h煅烧前驱体生成的ZnO纳米棒长度有所增加,ZnO的量基本保持不变。实验发现氧化锌的生长是沿着c轴方向,但是在横向也有生长方向。     

原位核磁共振技术研究光催化甲醇重整过程中甲醇与水的相互作用

本文利用原位液体核磁共振技术对真实固液体系光催化甲醇重整过程中水与甲醇之间的相互作用进行了系统性研究,证实了甲醇+水体系中氢键及质子交换相互作用的存在,并且发现催化剂的种类（包括不同晶型,以及同一晶型、不同形貌的TiO₂）、体系温度、光照反应条件都会影响甲醇与水之间的相互作用,进而影响到甲醇重整的效率．这表明催化剂及温度的合适选择对于提升甲醇重整效率起到非常重要的作用．     

镉掺杂氧化锌纳米花的制备及其光催化活性

以氯化锌、氯化镉、氢氧化钠为原料,采用水热法合成Cd掺杂纳米花状ZnO光催化剂,并通过该样品对罗丹明B水溶液的降解来研究其光催化活性。利用X射线衍射(XRD)、扫描电子显微镜(SEM)、X射线能量色散谱(EDS)、光致发光谱(PL)及紫外-可见分光光度计(UV-Vis)等测试手段对材料物性进行表征。实验结果表明:当掺杂Cd2+时,样品形貌发生变化、粒径减小;掺杂Cd2+后的ZnO的吸收边和紫外峰对比于纯ZnO均发生红移,禁带宽度由3.24 eV减小到3.16 eV。通过光催化实验分析可知,掺杂后纳米ZnO光催化剂对罗丹明B水溶液的降解率有所提高,光照3 h其降解率高达98%,说明与纯ZnO相比,Cd掺杂ZnO纳米花具有更高的光催化活性。     

镉掺杂氧化锌纳米花的制备及其光催化活性

以氯化锌、氯化镉、氢氧化钠为原料,采用水热法合成Cd掺杂纳米花状ZnO光催化剂,并通过该样品对罗丹明B水溶液的降解来研究其光催化活性。利用X射线衍射（XRD）、扫描电子显微镜（SEM）、X射线能量色散谱（EDS）、光致发光谱（PL）及紫外-可见分光光度计（UV-Vis）等测试手段对材料物性进行表征。实验结果表明：当掺杂Cd²⁺时,样品形貌发生变化、粒径减小;掺杂Cd²⁺后的ZnO的吸收边和紫外峰对比于纯ZnO均发生红移,禁带宽度由3.24 eV 减小到3.16 eV。通过光催化实验分析可知,掺杂后纳米ZnO光催化剂对罗丹明B 水溶液的降解率有所提高,光照3 h其降解率高达98%,说明与纯ZnO相比,Cd掺杂ZnO纳米花具有更高的光催化活性。     

MoO3-x/PCN的原位合成及其增强光催化产氢性能的研究

本文通过简单的一步浸渍煅烧法原位合成了氧化钼纳米晶/聚合物氮化碳复合光催化剂,该不含铂基助催化剂的氧化钼修饰聚合物氮化碳光催化剂在可见光照射下表现出增强的光催化产氢性能,最高产氢速率为15.6 μmol/h,是普通聚合物氮化碳样品的3倍以上. 相应的结构与性能的分析表明,与后浸渍法不同,在原位生长过程中高分散的超小氧化钼纳米晶体与聚合物氮化碳之间形成了紧密的耦合界面结构,可见光产氢活性的提升源自高分散的超小氧化钼纳米晶与聚合物氮化碳之间形成的紧密界面,以及该界面结构形成的肖特基结带来的有效电荷载流子转移.     

Core/shell structured ZnO/SiO2 nanoparticles: Preparation, characterization and photocatalytic property

ZnO nanoparticles were prepared by a simple chemical synthesis route. Subsequently, SiO₂ layers were successfully coated onto the surface of ZnO nanoparticles to modify the photocatalytic activity in acidic or alkaline solutions. The obtained particles were characterized by Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), transmission electron microscopy (TEM), energy dispersive spectrometry (EDS) and zeta potential. It was found that ultrafine core/shell structured ZnO/SiO₂ nanoparticles were successfully obtained. The photocatalytic performance of ZnO/SiO₂ core/shell structured nanoparticles in Rhodamine B aqueous solution at varied pH value were also investigated. Compared with uncoated ZnO nanoparticles, core/shell structured ZnO/SiO₂ nanoparticles with thinner SiO₂ shell possess improved stability and relatively better photocatalytic activity in acidic or alkaline solutions, which would broaden its potential application in pollutant treatment.     

Structural and optical properties of ZnO nanopowder prepared by microwave-assisted synthesis

We report the characterization of nano-size zinc oxide (ZnO) powder synthesized via microwave-assisted heating of Zn(CH₃COO)₂·2H₂O and NaHCO₃ solution with deionized water (DI water) as the solvent. The as-synthesized ZnO powder was calcined at temperatures from 400 to 800 °C for 8 h. The X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) spectra revealed pure wurtzite structure for the ZnO nanopowder (NP) calcined at 800 °C. Scanning electron microscopy (SEM) images showed increasing size ZnO NP with uniform size distribution with increase in calcination temperature. Significant UV emission at about 373 nm has been observed in the photoluminescence (PL) spectra of the as-synthesized and calcined ZnO NP. Our results showed enhanced PL intensity with a reduced full-width at half-maximum (FWHM) for ZnO NP synthesized at higher calcination temperature.     

Effect of post heat treatment on microstructure and photocatalytic activities of TiO2 nanoribbons

Low-dimensional TiO₂ nanoribbons were synthesized by a simple one-step hydrothermal method. The TiO₂ nanoribbons were calcined over the temperature range 200-800 °C in order to enhance their photocatalytic properties by altering their crystal phase and increasing crystallization. Effects of hydrothermal temperature, calcinated temperature and calcination time on the formation of nanostructures have been observed and characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The (BET) specific surface area of the samples which with different post treatments were determined by N₂ absorption-desorption experiment. In addition, photocatalytic activities of the nanoribbons were evaluated by photodegradation of organic dyes methyl orange under the radiation of UV light. The results reveal that the post-treatments have great effects on the microstructures and the photocatalytic activities of TiO₂ nanoribbons.     

Synthesis of ZnO-SnO2 composite oxides by CTAB-assisted co-precipitation and photocatalytic properties

ZnO-SnO₂ composite oxides with various molar ratios of Sn:Zn have been synthesized at different calcination temperatures via a facile cetyltrimethylammonium bromide (CTAB)-assisted co-precipitation method with Zn(NO₃)₂·6H₂O and SnCl₄·5H₂O as starting materials. XRD, TEM, SEM and BET were employed to characterize the as-prepared samples. It has been found that amorphous intermediates appear between the evolutions of ZnO and SnO₂ crystals. The photocatalytic properties of the composite oxides were investigated using photocatalytic degradation of methyl orange as the probe reaction. The results show that the ZnO-SnO₂ composite oxide with a cube morphology exhibits the best photocatalytic activity, which was prepared with a molar ratio of Zn:Sn of 2:1 and calcination temperature of 700 °C.     

Aqueous synthesis and enhanced photocatalytic activity of ZnO/Fe2O3 heterostructures

We report a facile synthesis of ZnO/Fe₂O₃ heterostructures based on the hydrolysis of FeCl₃ in the presence of ZnO nanoparticles. The material structure, composition, and its optical properties have been examined by means of transmission electron microscopy, scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and diffuse reflectance UV–visible spectroscopy. Results obtained show that 2.9 nm-sized Fe₂O₃ nanoparticles produced assemble with ZnO to form ZnO/Fe₂O₃ heterostructures. We have evaluated the photodegradation performances of ZnO/Fe₂O₃ materials using salicylic acid under UV-light. ZnO/Fe₂O₃ heterostructures exhibited enhanced photocatalytic capabilities than commercial ZnO due to the effective electron/hole separation at the interfaces of ZnO/Fe₂O₃ allowing the enhanced hydroxyl and superoxide radicals production from the heterostructure.     

Co3O4-ZnO hierarchical nanostructures by electrospinning and hydrothermal methods

A new hierarchical nanostructure that consists of cobalt oxide (Co₃O₄) and zinc oxide (ZnO) was produced by the electrospinning process followed by a hydrothermal technique. First, electrospinning of a colloidal solution that consisted of zinc nanoparticles, cobalt acetate tetrahydrate and poly(vinyl alcohol) was performed to produce polymeric nanofibers embedding solid nanoparticles. Calcination of the obtained electrospun nanofiber mats in air at 600 °C for 1 h, produced Co₃O₄ nanofibers with rough surfaces containing ZnO nanoparticles (i.e., ZnO-doped Co₃O₄ nanofibers). The rough surfaced nanofibers, containing ZnO nanoparticles (ZnNPs), were then exploited as seeds to produce ZnO nanobranches using a specific hydrothermal technique. Scanning electron microscopy (SEM), and transmission electron microscopy (TEM) were employed to characterize the as-spun nanofibers and the calcined product. X-ray powder diffractometery (XRD) analysis was used to study the chemical composition and the crystallographic structure.     

Synthesis, characterization and effect of calcination temperature on phase transformation and photocatalytic activity of Cu,S-codoped TiO2 nanoparticles

A novel copper and sulfur codoped TiO₂ photocatalyst was synthesized by modified sol-gel method using titanium(IV) isopropoxide, CuCl₂·2H₂O and thiourea as precursors. The samples were characterized by X-ray diffraction (XRD), diffuse reflectance spectroscopy (DRS), scanning electron microscopy equipped with energy dispersive X-ray micro-analysis (SEM-EDX), transmission electron microscopy (TEM) and Fourier transform infrared (FT-IR) analysis. The XRD results showed undoped and Cu,S-codoped TiO₂ nanoparticles only include anatase phase. Effect of calcination temperature showed rutile phase appears in 650 and 700 °C for undoped and 0.1% Cu,S-codoped TiO₂, respectively. The SEM analysis revealed the doping of Cu and S does not leave any change in morphology of the catalyst surface. The increase of copper doping enhanced “red-shift” in the UV-vis absorption spectra. The TEM images confirmed the dopants suppressed the growth of TiO₂ grains. The photocatalytic activity of samples was tested for degradation of methyl orange (MO) solutions. The results showed photocatalytic activity of the catalysts with 0.05% Cu,0.05% S and 0.1% Cu,0.05% S were higher than that of other catalysts under ultraviolet (UV) and visible irradiation, respectively. Because of synergetic effect of S and Cu, the Cu,S-codoped TiO₂ catalyst has higher activity than undoped and Cu or S doped TiO₂ catalysts.     

从可溶性单源分子前驱体采用溶胶凝胶法制备ZnO/TiO2 纳米复合物

合成了单源分子前驱体Cl₂TiZn(dmae)₄ (dmae为2-二甲基乙醇胺),并以乙醇为溶剂,加入等摩尔量的水对其进行可控水解得ZnO/TiO₂纳米复合凝胶,经pH=9沉淀,在200、400和600 oC 烧结得到不同的产物T₂₀₀、T₄₀₀、T₆₀₀. XRD分析表明未烧结产物为无定形粉末并随着烧结温度升高晶型改善. ZnO呈纤锌矿结构(六方晶系),TiO₂呈板钛矿型结构(正交). BET分析和扫描电镜表明颗粒的大小随着烧结温度的提高而增加. 红外光谱证明Zn-O和Ti-O的特有的振动频率,OH基团烧结后的产物中被去掉. 所有的样品都显示良好的光催化活性, 且T₆₀₀活性最高.     

铈和磷钨酸共掺杂纳米二氧化钛中空纤维的制备及其光催化活性

以棉花纤维为模板,以钛酸四正丁酯、硝酸铈铵和磷钨酸为原料采用模板法制备了一系列铈和磷钨酸共掺杂的、具有中空纤维结构的TiO₂光催化材料, 利用扫描电子显微镜、X射线衍射、BET和紫外-可见光谱等技术对其形貌、晶体结构及表面结构、光吸收特性等进行了表征. 以苯酚溶液的光催化降解为模型反应,考察了不同掺杂量的样品在紫外和可见光下的光催化性能. 结果表明,用模板法制备的TiO₂纤维材料具有中空结构,共掺杂的TiO₂纤维在紫外和可见光条件下较纯TiO₂纤维和单掺杂TiO₂纤维对苯酚溶液具有更好的光催化降解效果, 且铈和磷钨酸的掺杂量显著影响该纤维材料的催化性能;当铈掺杂量为0.3mol%和磷钨酸掺杂量为2mol%,在500 oC焙烧2 h所得中空纤维材料的催化性能最佳,4 h即可使苯酚溶液的降解率达98.5%;重复使用4次仍可使苯酚溶液的降解率保持在87%以上,且该催化剂材料易于离心分离去除.     

A simple sonochemical approach for synthesis and characterization of Zn2SiO4 nanostructures

Zn₂SiO₄ nanoparticles have been successfully prepared via a simple sonochemical method, for the first time. The effect of various parameters including ultrasonic power, ultrasonic irradiation time and different surfactants were investigated to reach optimum condition. The as-prepared nanostructures were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmittance electron microscopy (TEM), Fourier transform infrared (FT-IR) spectra and energy dispersive X-ray microanalysis (EDX). The photocatalytic activity of Zn₂SiO₄ nano and bulk structures were compared by degradation of anionic dye methyl orange in aqueous solution under UV-light irradiation. Moreover, the cyclic voltammetry analysis of Zn₂SiO₄ nano and bulk structures were investigated.