Separation and determination of amitriptyline and nortriptyline by dispersive liquid-liquid microextraction combined with gas chromatography flame ionization detection

Dispersive liquid–liquid microextraction (DLLME) coupled with gas chromatography–flame ionization detection (GC–FID) was applied for the determination of two tricyclic antidepressant drugs (TCAs), amitriptyline and nortriptyline, from water samples. This method is a very simple and rapid method for the extraction and preconcentration of these drugs from environmental sample solutions. In this method, the appropriate mixture of extraction solvent (18 μL Carbon tetrachloride) and disperser solvent (1 mL methanol) are injected rapidly into the aqueous sample (5.0 mL) by syringe. Therefore, cloudy solution is formed. In fact, it is consisted of fine particles of extraction solvent which is dispersed entirely into aqueous phase. The mixture was centrifuged and the extraction solvent is sedimented on the bottom of the conical test tube. 2.0 μL of the sedimented phase is injected into the GC for separation and determination of TCAs. Some important parameters, such as kind of extraction and disperser solvent and volume of them, extraction time, pH and ionic strength of the aqueous feed solution were optimized. Under the optimal conditions, the enrichment factors and extraction recoveries were between 740.04–1000.25 and 54.76–74.02%, respectively. The linear range was (0.005–16 μg mL⁻¹) and limits of detection were between 0.005 and 0.01 μg mL⁻¹ for each of the analytes. The relative standard deviations (R.S.D.) for 4 μg mL⁻¹ of TCAs in water were in the range of 5.6–6.4 (n = 6). The performance of the proposed technique was evaluated for determination of TCAs in blood plasma.     

Determination of organochlorine pesticides in ground water samples using solid-phase microextraction by gas chromatography-electron capture detection

A direct immersion solid-phase microextraction coupled with gas chromatography-electron capture detection (SPME-GC-ECD) method was optimized and validated for the quantitative determination of 18 organochlorine pesticides in ground water. Ionic strength, stirring speed, adsorption and desorption time and pH were some of the parameters investigated in order to select the optimum conditions for SPME with a 50/30 DVB/CAR/PDMS fiber coating. The SPME-GC/ECD method showed good linear response below 10 ng L⁻¹ with R² values in the range of 0.9950–0.9997. The repeatability of the measurements were lower than 10%. Values of relative recoveries located within the acceptable range (80–120%). Limits of quantification (LOQ) from 4.5 × 10⁻³ to 1.5 ng L⁻¹ were obtained. On average 8 organochlorines were found per sample, even so all the 18 organochlorines were quantified among them. Substances such as endrin ketone, γ-BHC and β-BHC were the pesticides determined in larger concentration (0.06–305 ng L⁻¹), while methoxychlor and aldrin in smaller amounts (0.151–1.55 ng L⁻¹). Measured levels of organochlorine pesticides were above the limits established by Brazilian regulations.     

Structure and conformational properties of carbonylbisimidosulfuryl fluoride, O=C(N=S(O)F2)2

The molecular structure and conformational properties of O=C(N=S(O)F₂)₂ (carbonylbisimidosulfuryl fluoride) were determined by gas electron diffraction (GED) and quantumchemical calculations (HF/3-21G* and B3LYP/6-31G*). The analysis of the GED intensities resulted in a mixture of 76(12)% syn–syn and 24(12)% syn–anti conformer (ΔH⁰=H⁰(syn–anti)−H⁰(syn–syn)=1.11(32) kcal mol⁻¹) which is in agreement with the interpretation of the IR spectra (68(5)% syn–syn and 32(5)% syn–anti, ΔH⁰=0.87(11) kcal mol⁻¹). syn and anti describe the orientation of the S=N bonds relative to the C=O bond. In both conformers the S=O bonds of the two N=S(O)F₂ groups are trans to the C–N bonds. According to the theoretical calculations, structures with cis orientation of an S=O bond with respect to a C–N bond do not correspond to minima on the energy hyperface. The HF/3-21G* approximation predicts preference of the syn–anti structure (ΔE=−0.11 kcal mol⁻¹) and the B3LYP/6-31G* method results in an energy difference (ΔE=1.85 kcal mol⁻¹) which is slightly larger than the experimental values. The following geometric parameters for the O=C(N=S)₂ skeleton were derived (r_a values with 3σ uncertainties): C=O 1.193 (9) Å, C–N 1.365 (9) Å, S=N 1.466 (5) Å, O=C–N 125.1 (6)° and C–N=S 125.3 (10)°. The geometric parameters are reproduced satisfactorily by the HF/3-21G* approximation, except for the C–N=S angle which is too large by ca. 6°. The B3LYP method predicts all bonds to be too long by 0.02–0.05 Å and the C–N=S angle to be too small by ca. 4°.     

Metal doped silica membrane reactor: Operational effects of reaction and permeation for the water gas shift reaction

In this work, we investigate the performance of metal (Cobalt) doped silica membranes in a membrane reactor (MR) configuration for the low temperature water gas shift (WGS) reaction. The membranes were hydrostable and showed activated transport even after 2 weeks exposure to steam. High CO conversions resulted in the H₂ and CO partial pressures in the reaction chamber moving in opposite directions, thus favouring H₂/CO separation to treble (5–15) from 150 to 250 °C. On the other hand, the separation of H₂/CO₂ remained relatively low (2–4) as the driving force for diffusion or partial pressure of these gases remained equal in the reaction chamber irrespective of the extent of conversion. Below approximately 40% CO conversion, the MR is ineffective as the H₂ driving force for permeation was so low that H₂/CO selectivity was below unity. Operating under equilibrium limited conversion (space velocities 7500 h⁻¹) conditions, very high conversions in excess of 95% were observed and there were no significant advantages of the MR performance over the packed bed reactor (PBR). However, for higher throughputs (space velocities 38000 and 75000 h⁻¹) conversion is affected by the reaction rate, and relatively enough H₂ is removed from the reactor through the membrane. Increasing temperature to 250 °C as a function of the space velocity (75000 h⁻¹) allowed for the CO conversion in the MR to shift up to 12% as compared to the PBR.     

Analysis of acrylamide in different foodstuffs using liquid chromatography–tandem mass spectrometry and gas chromatography–tandem mass spectrometry

Acrylamide levels over a wide range of different food products were analysed using both liquid chromatography–tandem mass spectrometry (HPLC–MS–MS) and gas chromatography–tandem mass spectrometry (GC–MS–MS). Two different sample preparation methods for HPLC–MS–MS analysis were developed and optimised with respect to a high sample throughput on the one hand, and a robust and reliable analysis of difficult matrices on the other hand. The first method is applicable to various foods like potato chips, French fries, cereals, bread, and roasted coffee, allowing the analysis of up to 60 samples per technician and day. The second preparation method is not as simple and fast but enables analysis of difficult matrices like cacao, soluble coffee, molasses, or malt. In addition, this method produces extracts which are also well suited for GC–MS–MS analysis. GC–MS–MS has proven to be a sensitive and selective method offering two transitions for acrylamide even at low levels up to 1 μg kg⁻¹. For the respective methods the repeatability (n=10), given as coefficient of variation, ranged from 3% (acrylamide content of 550 μg kg⁻¹) to 12% (acrylamide content of 8 μg kg⁻¹) depending on the food matrix. The repeatability (n=3) for different food samples spiked with acrylamide (5–1500 μg kg⁻¹) ranged from 1 to 20% depending on the spiking level and the food matrix. The limit of quantification (referred to a signal-to-noise ratio of 9:1) was 30 μg kg⁻¹ for HPLC–MS–MS and 5 μg kg⁻¹ for GC–MS–MS. It could be demonstrated that measurement uncertainties were not only a result of analytical variability but also of inhomogeneity and stability of the acrylamide in food.     

A novel sol-gel-based amino-functionalized fiber for headspace solid-phase microextraction of phenol and chlorophenols from environmental samples

A novel amino-functionalized polymer was synthesized using 3-(trimethoxysilyl) propyl amine (TMSPA) as precursor and hydroxy-terminated polydimethylsiloxane (OH-PDMS) by sol–gel technology and coated on fused-silica fiber. The synthesis was designed in a way to impart polar moiety into the coating network. The scanning electron microscopy (SEM) images of this new coating showed the homogeneity and the porous surface structure of the film. The efficiency of new coating was investigated for headspace solid-phase microextraction (SPME) of some environmentally important chlorophenols from aqueous samples followed by gas chromatography–mass spectrometry (GC–MS) analysis. Effect of different parameters influencing the extraction efficiency such as extraction temperature, extraction time, ionic strength and pH was investigated and optimized. In order to improve the separation efficiency of phenolic compounds on chromatography column all the analytes were derivatized prior to extraction using acetic anhydride at alkaline condition. The detection limits of the method under optimized conditions were in the range of 0.02–0.05 ng mL⁻¹. The relative standard deviations (R.S.D.) (n = 6) at a concentration level of 0.5 ng mL⁻¹ were obtained between 6.8 and 10%. The calibration curves of chlorophenols showed linearity in the range of 0.5–200 ng mL⁻¹. The proposed method was successfully applied to the extraction from spiked tap water samples and relative recoveries were higher than 90% for all the analytes.     

Diagnostics of water-containing gas mixtures using thermal laser-induced gratings

Laser-induced gratings (LIGs) experiments, employing vibrational-overtone excitation of H₂O molecules through rovibrational transitions of the (2 1 1) ← (0 0 0) band around 820 nm to produce gratings, have been performed in humid ambient air, in a room-temperature cell with neat water vapor or that diluted in buffer gas at pressures of 0.02–4 bar, and in the vicinity of premixed atmospheric pressure CH₄-air flame, with the aim to investigate the feasibilities of the techniques for accomplishing gas diagnostics or tracing H₂O at various temperatures and pressures.

In highly vibrationally-excited H₂O rapid multi-stage collisional thermalization processes occur, and as a result both strong oscillatory (due to standing acoustic waves) and stationary (due to stationary density modulations) contributions to LIGs have been observed in gas mixtures.

Temporal profiles of LIG signals recorded at various conditions of gas mixtures employed have been analysed in frame of a model of a two- or three-stage R–T, V–V′, and V–T collisional relaxation of H₂O and buffer gas molecules. The informative parameters, like adiabatic sound velocity, gas temperature, H₂O mole fraction have been derived. The results of the analysis are presented, demonstrating possibilities and challenges of the technique in application to gas diagnostics.     

Simultaneous determination of sugars and organic acids in aged vinegars and chemometric data analysis

Aceto Balsamico Tradizionale of Modena (ABTM) is a typical product (PDO denomination) of the province of Modena produced by cooked grape must which undergoes a long ageing period (at least 12 years) in series of wooden casks (batterie). The study of the transformations of this product during ageing is extremely relevant in order to control the authenticity of ABTM towards succedaneous products and mislabelling of age.

This paper presents the results of the investigation of sugars and fixed organic acids in ABTM samples of different ages, coming from different batterie. The analytes were simultaneously determined by a gas chromatographic method optimised for this peculiar matrix.

The method shows good separation and resolution of the investigated chemical species and allows their determination in the concentration ranges reported in brackets: malic (7.6–15.5 g kg⁻¹), tartaric (4.0–9.7 g kg⁻¹), citric (0.6–1.5 g kg⁻¹) and succinic (0.36–0.62 g kg⁻¹) acid and glucose (153–294 g kg⁻¹), fructose (131–279 g kg⁻¹), xylose (011–0.39 g kg⁻¹), ribose (0.078–0.429 g kg⁻¹), rhamnose (0.061–0.195 g kg⁻¹), galactose (0.136–0.388 g kg⁻¹), mannose (0.41–1.46 g kg⁻¹), arabinose (0.33–1.00 g kg⁻¹) and sucrose (0.46–6.84 g kg⁻¹), with mean associated errors ranging from 5 to 19% depending on the analytes.

Moreover, the recovery values are always satisfactory, being close to one for most of the analytes.

Furthermore, in order to assess the degree of variability of the different analytes content with vinegar ageing and the similarity/dissimilarity among series of casks a three-way data analysis method (Tucker3) is proposed. The chemometric technique applied on the data set shows differences between the samples on the bases of their different ageing period, and between the batterie, which traditionally have an own peculiar production procedure.     

A multi-commuted flow injection system with a multi-channel propulsion unit placed before detection: Spectrophotometric determination of ammonium

A flow system with a multi-channel peristaltic pump placed before the solenoid valves is proposed to overcome some limitations attributed to multi-commuted flow injection systems: the negative pressure can lead to the formation of unwanted air bubbles and limits the use of devices for separation processes (gas diffusion, dialysis or ion-exchange). The proposed approach was applied to the colorimetric determination of ammonium nitrogen. In alkaline medium, ammonium is converted into ammonia, which diffuses over the membrane, causing a pH change and subsequently a colour change in the acceptor stream (bromothymol blue solution). The system allowed the re-circulation of the acceptor solution and was applied to ammonium determination in surface and tap water, providing relative standard deviations lower than 1.5%. A stopped flow approach in the acceptor stream was adopted to attain a low quantification limit (42 μg L⁻¹) and a linear dynamic range of 50–1000 μg L⁻¹ with a determination rate of 20 h⁻¹.     

Trace analysis of chlorobenzenes in water samples using headspace solvent microextraction and gas chromatography/electron capture detection

In the present work, a rapid method for the extraction and determination of chlorobenzenes (CBs) such as monochlorobenzene, 1,2-dichlorobenzene, 1,3-dichlorobenzene, 1,4-dichlorobenzene, 1,2,3-trichlorobenzene and 1,2,4-trichlorobenzene in water samples using the headspace solvent microextraction (HSME) and gas chromatography/electron capture detector (ECD) has been described. A microdrop of the dodecane containing monobromobenzene (internal standard) was used as extracting solvent in this investigation. The analytes were extracted by suspending a 2.5 μl extraction drop directly from the tip of a microsyringe fixed above an extraction vial with a septum in a way that the needle passed through the septum and the needle tip appeared above the surface of the solution. After the extraction was finished, the drop was retracted back into the needle and injected directly into a GC column. Optimization of experimental conditions such as nature of the extracting solvent, microdrop and sample temperatures, stirring rate, microdrop and sample volumes, the ionic strength and extraction time were investigated. The optimized conditions were as follows: dodecane as the extracting solvent, the extraction temperature, 45 °C; the sodium chloride concentration, 2 M; the extraction time, 5.0 min; the stirring rate, 500 rpm; the drop volume, 2.5 μl; the sample volume, 7 ml; the microsyringe needle temperature, 0.0 °C. The limit of detection (LOD) ranged from 0.1 μg/l (for 1,3-dichlorobenzene) to 3.0 μg/l (for 1,4-dichlorobenzene) and linear range of 0.5–3.0 μg/l for 1,2-dichlorobenzene, 1,3-dichlorobenzene and from 5.0 to 20.0 μg/l for monochlorobenzene and from 5.0 to 30 μg/l for 1,4-dichlorobenzene. The relative standard deviations (R.S.D.) for most of CBs at the 5 μg/l level were below 10%. The optimized procedure was successfully applied to the extraction and determination of CBs in different water samples.     

Gas transport property of polyallylamine–poly(vinyl alcohol)/polysulfone composite membranes

Polyallylamine (PAAm) was synthesized by free radical polymerization and characterized by Fourier transform infrared resonance (FT-IR) spectroscopy, hydrogen nuclear magnetic resonance (¹H NMR) spectroscopy and differential scanning calorimetry (DSC). The composite membranes were prepared by using PAAm–poly(vinyl alcohol) (PVA) blend polymer as the separation layer and polysulfone (PSF) ultrafiltration membranes as the support layer. The surface and cross-section morphology of the membrane was inspected by environmental scanning electron microscopy (ESEM). The gas transport property of the membranes, including gas permeance, flux and selectivity, were investigated by using pure CO₂, N₂, CH₄ gases and CO₂/N₂ gas mixture (20 vol% CO₂ and 80 vol% N₂) and CO₂/CH₄ gas mixture (10 vol% CO₂ and 90 vol% CH₄). The plots of gas permeance or flux versus feed gas pressure imply that CO₂ permeation through the membranes follows facilitated transport mechanism whereas N₂ and CH₄ permeation follows solution–diffusion mechanism. Effect of PAAm content in the separation layer on gas transport property was investigated by measuring the membranes with 0–50 wt% PAAm content. With increasing PAAm content, gas permeance increases initially, reaches a maximum, and then decreases gradually. For CO₂/N₂ gas mixture, the membranes with 10 wt% PAAm content show the highest CO₂ permeance of about 1.80 × 10⁻⁵ cm³ (STP) cm⁻² s⁻¹ KPa⁻¹ and CO₂/N₂ selectivity of 80 at 0.1 MPa feed gas pressure. For CO₂/CH₄ gas mixture, the membranes with 20 wt% PAAm content display the highest CO₂ permeance of about 1.95 × 10⁻⁵ cm³ (STP) cm⁻² s⁻¹ KPa⁻¹ and CO₂/CH₄ selectivity of 58 at 0.1 MPa feed gas pressure. In order to explore the possible reason of gas permeance varying with PAAm content, the crystallinity of PVA and PAAm–PVA blend polymers was measured by X-ray diffraction (XRD) spectra. The experimental results show an inverse relationship between crystallinity and gas permeance, e.g., a minimum crystallinity and a maximum CO₂ permeance are obtained at 20 wt% PAAm content, indicating that the possibility of increasing CO₂ permeance with PAAm content due to the increase of carrier concentration could be weakened by the increase of crystallinity.     

The efficacy of nitrosonaphthol functionalized XAD-16 resin for the preconcentration/sorption of Ni(II) and Cu(II) ions

Amberlite XAD-16 resin has been functionalized using nitrosonaphthol as a ligand and characterized employing elemental, thermogravimetric analysis and FT-IR spectroscopy. The sorption of Ni(II) and Cu(II) ions onto this functionalized resin is investigated and optimized with respect to the sorptive medium (pH), shaking speed and equilibration time between liquid and solid phases. The monitoring of the influence of diverse ions on the sorption of metal ions has revealed that phosphate, bicarbonate and citrate reduce the sorption up to 10–14%. The sorption data followed Langmuir, Freundlich, and Dubinin–Radushkevich (D–R) isotherms. The Freundlich parameters computed are 1/n = 0.56 ± 0.03 and 0.49 ± 0.05, A = 9.54 ± 1.5 and 6.0 ± 0.5 mmol g⁻¹ for Ni(II) and Cu(II) ions, respectively. D–R isotherm yields the values of X_m = 0.87 ± 0.07 and 0.35 ± 0.05 mmol g⁻¹ and of E = 9.5 ± 0.23 and 12.3 ± 0.6 kJ mol⁻¹ for Ni(II) and Cu(II) ions, respectively. Langmuir characteristic constants estimated are Q = 0.082 ± 0.005 and 0.063 ± 0.003 mmol g⁻¹, b = (4.7 ± 0.2) × 10⁴ and (7.31 ± 0.11) × 10⁴ l mol⁻¹ for Ni(II) and Cu(II) ions, respectively. The variation of sorption with temperature gives thermodynamic quantities of ΔH = −58.9 ± 0.12 and −40.38 ± 0.11 kJ mol⁻¹, ΔS = −183 ± 10 and −130 ± 8 J mol⁻¹ K⁻¹ and ΔG = −4.4 ± 0.09 and −2.06 ± 0.08 kJ mol⁻¹ at 298 K for Ni(II) and Cu(II) ions, respectively. Using kinetic equations, values of intraparticle transport and of first order rate constant have been computed for both the metal ions. The sorption procedure is utilized to preconcentrate these ions prior to their determination in tea, vegetable oil, hydrogenated oil (ghee) and palm oil by atomic absorption spectrometry using direct and standard addition methods.     

Crystalline polysilicate magadiite with intercalated n-alkylmonoamine and some correlations involving thermochemical data

Synthesized hydrated lamellar acidic crystalline magadiite (H₂Si₁₄O₂₉·2H₂O) nanocompound was used as host for intercalation of polar n-alkylmonoamine molecules of the general formula H₃C(CH₂)_nNH₂ (n = 1–6) in aqueous solution. The original interlayer distance (d) of 1500 pm, determined by X-ray powder diffraction patterns, increases after intercalation. The values correlated with the number of aliphatic amine carbon (n_c) atoms: d = [(1312 ± 11) + (21 ± 2)]n_c. The amount of intercalated amines (N_s), decreased as n_c increased: N_s = [(5.82 ± 0.04) − (0.45 ± 0.01)]n_c. The acidic layered nanocompound was calorimetrically titrated with the amines and the thermodynamic data gave exothermic values for all guest molecules, as shown by the correlation: Δ_intH = −[(24.45 ± 0.49) − (1.91 ± 0.10)]n_c and d = [(1576 ± 16) − (10.8 ± 1.0)]Δ_intH. The negative values of the Gibbs energies and the positive entropies also presented the correlations: Δ_intG = −[(22.8 ± 0.2) − (0.2 ± 0.1)]n_c and Δ_intS = [(6 ± 1) + (5 ± 1)]n_c, respectively.     

Polarographic chemometric determination of zinc and nickel in aqueous samples

Polarographic chemometric methods were applied to the determination of zinc and nickel in aqueous solutions previously acidified with 0.1 M acetate buffer (pH 4.2). The studied methods are multivariate methods including classical least squares (CLS), principal component regression (PCR) and partial least squares (PLS); derivative ratio methods (first, ¹D and second, ²D derivative ratio). A comparative study was considered. The studied chemometric methods do not need the presence of any reduction potential shift reagent in spite of the great overlap between the two metals polarograms. A training set consisting of 10 binary mixture solutions in the possible combinations containing 0.13–9.30 μg/ml Zn(II) and 0.20–12.25 μg/ml Ni(II) was used to develop the chemometric calibrations (CLS, PCR and PLS). A validation set containing the synthetic mixtures in the range of 0.29–9.00 μg/ml for Zn(II) and 0.30–11.60 μg/ml for Ni(II) was used to validate the multivariate calibrations. Same mixtures were used to develop the derivative ratio methods. The polarograms were recorded and their current values were measured within the potential range −920 to −1052 mV at 2 mV intervals. The mean percentage recoveries obtained using CLS, PCR and PLS were found to be 99.5 ± 1.5%, 100.0 ± 1.1% and 100.0 ± 1.0% for Zn(II) and 99.4 ± 1.3%, 99.7 ± 1.2% and 99.9 ± 1.0% for Ni(II), respectively. The mean percentage recoveries obtained using ¹D at −950 mV, ¹D at −1010 mV, ¹D at −950 mV–¹D at −1010 mV and ²D at −986 mV for Zn(II) were found to be 99.7 ± 1.2%, 99.2 ± 1.6%, 99.4 ± 1.4% and 99.4 ± 1.4%; and using ¹D at −1030 mV and ²D at −1010 mV for Ni(II) were found to be 100.5 ± 1.3% and 100.4 ± 1.3%, respectively. Interferences due to the presence of Cd, Co, Pb, Fe, Mn, Ca, Mg, Cu and Al were studied. The applicability of the proposed methods was assessed through the determination of both metals in tap drinking-water. Samples were subjected if required up to a 20-fold preconcentration step by microwaving in pyrex vessels. The results were compared with those obtained using the zincon and the heptoxime colorimetric reference methods for the determination of zinc and nickel, respectively.     

Analysis for chloroanisoles and chlorophenols in cork by stir bar sorptive extraction and gas chromatography–mass spectrometry

A complete methodology for the determination of chloroanisoles and chlorophenols in cork material is proposed. The determination is accomplished by means of a previous liquid–solid extraction followed by stir bar sorptive extraction (SBSE) coupled to gas chromatography–mass spectrometry (GC–MS). Two different liquid–solid extraction experiments were conducted and eight compounds considered (2,6-dichloroanisole, 2,4-dichloroanisole, 2,4,6-trichloroanisole, 2,4,6-trichlorophenol, 2,3,4,6-tetrachloroanisole, 2,3,4,6-tetrachlorophenol, pentachloroanisole and pentachlorophenol). From the results obtained we can conclude that high volume extraction extending extraction time up to 24 h is the best choice if we have to release compounds from the inner surfaces of cork stoppers. Recovery percentages ranged from 51% for pentachloroanisole to 81% for 2,4-dichloroanisole. This method allows the determination of an array of compounds involved in cork taint at very low levels from 1.2 ng g⁻¹ for 2,4,6-tricholoroanisole to 23.03 ng g⁻¹ for 2,3,4,6-tetrachlorophenol.     

Determination of chlorite in drinking water by on-line coupling of capillary isotachophoresis and capillary zone electrophoresis

An isotachophoresis (ITP)–capillary zone electrophoresis (CZE) combination was used for the determination of chlorite in drinking waters. No sample preparation is needed and no interfering by other anions in tap water was observed. The reached limits of detection with conductivity detector were 0.012–0.017 mg l⁻¹. By four-fold sample loading with a 30 μl valve, 0.005 mg l⁻¹ of chlorite was determined with R.S.D.=3.3%. The concentrations of 0.05 and 0.20 mg l⁻¹ were measured with R.S.D. of 2.2 and 2.7%, respectively. The recoveries of chlorite from drinking water were 96–106% in the range of 0.02–0.20 mg l⁻¹. The R.S.D. values of migration times (inter-day) were up to 1.3%. The time for analysis is about 15 min.     

Preparation of novel ion exchange polyurethane foam and its application for separation and determination of palladium in environmental samples

The new strong anion exchanger (PUFIX) from polyurethane foam was prepared by coupling of the primary amine of the foam matrix with ethyl iodide. PUFIX was characterized using different tools (IR spectra, elemental analysis, density and thermal analysis). The sorption properties of the new anion exchanger (PUFIX) and chromatographic behaviour for separation and determination of palladium(II) ions at low concentrations from aqueous iodide or thiocyanate media were investigated by a batch and dynamic processes. The maximum sorption of Pd(II) was in the pH range of 0.3–2. The kinetics of sorption of the Pd(II) by the PUFIX was found to be fast with average values of half-life of sorption (t_1/2) of 3.32 min. The variation of the sorption of Pd(II) with temperature gives average values of ΔH, ΔS, ΔG and ΔE to be −38.3 kJ mol⁻¹, −100.7 J K⁻¹ mol⁻¹, −8.3 and 11.8 kJ mol⁻¹, respectively. The sorption capacity of PUFIX was 1.69 mmol g⁻¹ for Pd(II), preconcentration factors of values ≈250 and the recovery 99–100% were achieved (R.S.D. ≈ 1.24%). The lower detection limit, 1.28 ng mL⁻¹ was evaluated using spectrophotometric method (R.S.D. ≈ 2.46%).     

Conformational studies of cyclopropylmethyl isocyanate from temperature dependent FT-IR spectra of xenon solutions and ab initio calculations

Variable temperature (−55 to −100 °C) studies of the infrared spectra (3200 to 100 cm⁻¹) of cyclopropylmethyl isocyanate, c-C₃H₅CH₂NCO, dissolved in liquefied xenon, have been carried out. The infrared spectra (gas and solid) as well as the Raman spectrum of the liquid have been recorded from 3200 to 100 cm⁻¹. By analyzing six conformer pairs in xenon solutions, an enthalpy difference of 193 ± 19 cm⁻¹ (2.31 ± 0.23 kJ/mol) was obtained with the gauche–cis rotamer (the first designation indicates the orientation of the CNCO group with respect to the three-membered ring, the second designation indicates the relative orientation of the NCO group with respect to the bridging CC bond) the more stable form and the only form present in polycrystalline solid. The abundance of the cis–trans conformer present at ambient temperature is 16 ± 1%. The potential function governing the conformational interchange has been obtained from B3LYP/6-31G(d) calculations and the two-dimensional potential has been obtained. From MP2 ab initio calculations utilizing various basis sets with diffuse functions, the gauche–cis conformer is predicted to be more stable by 223 to 269 cm⁻¹, which is consistent with the experimental results. However, without diffuse functions the predicted conformational energy differences are much smaller (77–166 cm⁻¹). Similar diffuse function dependency affects density functional theory calculations by the B3LYP method to a lesser extent. A complete vibrational assignment for the gauche–cis conformer is proposed and several fundamentals for the cis–trans conformer have been identified. The structural parameters, dipole moments, conformational stability, vibrational frequencies, infrared intensities and Raman activities have been predicted from ab initio calculations and r₀ structural parameters are estimated. These experimental and theoretical results are compared to the corresponding quantities of some similar molecules.     

Comparison of AFS and ICP-MS detection coupled with gas chromatography for the determination of methylmercury in marine samples

Inductively coupled plasma mass spectrometry (ICP-MS) and atomic fluorescence spectrometry (AFS) coupled with gas chromatography (GC) have been evaluated as element specific detectors for the determination of methylmercury in marine samples. Detection limits for methylmercury chloride, obtained using ICP-MS and AFS, were 0.9 and 0.25 pg as Hg, respectively. Methylmercury was determined in marine tissue reference materials IAEA 142 and NIST 8044 mussel homogenate, and DOLT-2 dogfish liver by GC–AFS, with found values of 45±7, 26±4, and 671±41 ng g⁻¹, compared with certified values of 47±4, 28±2, and 693±53 ng g⁻¹. The analyses of IAEA 142 and NIST 8044 were repeated using GC–ICP-MS, with found values of 48±9 and 30±3 ng g⁻¹, respectively. Methylmercury was determined in real samples of ringed seal and beluga whale, with found values of 801±62 and 2830±113 ng g⁻¹, respectively.