Synthesis and characterization of poly(methyl methacrylate)/casein nanoparticles with a well‐defined core‐shell structure

Well‐defined, core‐shell poly(methyl methacrylate) (PMMA)/casein nanoparticles, ranging from 80 to 130 nm in diameter, were prepared via a direct graft copolymerization of methyl methacrylate (MMA) from casein. The polymerization was induced by a small amount of alkyl hydroperoxide (ROOH) in water at 80 °C. Free radicals on the amino groups of casein and alkoxy radicals were generated concurrently, which initiated the graft copolymerization and homopolymerization of MMA, respectively. The presence of casein micelles promoted the emulsion polymerization of the monomer and provided particle stability. The conversion and grafting efficiency of the monomer strongly depended on the type of radical initiator, ROOH concentration, casein to MMA ratio, and reaction temperature. The graft copolymers and homopolymer of PMMA were isolated and characterized with Fourier transform infrared spectroscopy and differential scanning calorimetry. The molecular weight determination of both the grafted and homopolymer of PMMA suggested that the graft copolymerization and homopolymerization of MMA proceeded at a similar rate. The transmission electron microscopic image of the nanoparticles clearly showed a well‐defined core‐shell morphology, where PMMA cores were coated with casein shells. The casein shells were further confirmed with a zeta‐potential measurement. Finally, this synthetic method allowed us to prepare PMMA/casein nanoparticles with a solid content of up to 31%. Thus, our new process is commercially viable. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3346–3353, 2003     

Novel core-shell nanoparticles and their application in high-capacity immobilization of enzymes

Novel core-shell nanoparticles consisting of poly(methyl methacrylate) (PMMA) cores coated with synthetic polymer and biopolymer (polyethyleneimine, chitosan, and casein) shells were synthesized via direct graft copolymerization of methyl methacry late from hydrophilic polymers in the absence of surfactant. Average hydrodynamic diameters of the nanoparticles ranged from 163 to 263 nm. High-capacity (up to 530 mg/g) immobilizations of enzymes and high-activity retained percentage (E _spe) (up to 90%) were achieved.     

Preparation of CO2‐switchable latexes using N‐[3‐(dimethylamino)propyl]‐methacrylamide (DMAPMAm)

CO₂‐switchable polystyrene (PS), poly(methyl methacrylate) (PMMA), and poly(butyl methacrylate) (PBMA) latexes were prepared via surfactant‐free emulsion polymerization (SFEP) under a CO₂ atmosphere, employing N‐[3‐(dimethylamino)propyl]methacrylamide (DMAPMAm) as a CO₂‐switchable, water‐soluble, and hydrolytically stable comonomer. The conversion of the SFEP of styrene reaches >95% in less than 5 h. The resulting latexes have near monodisperse particles (PDI ≤ 0.05), as confirmed by DLS and TEM. The latexes could be destabilized by bubbling nitrogen (N₂) and heating at 65 °C for 30 min, and easily redispersed by only bubbling CO₂ for a short time without using sonication. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 1059–1066     

A Way to Prepare Core‐Shell Biocompatible Polymeric Nano‐Particles from Gelatin and Acrylic Acid

Narrowly distributed core‐shell nano‐particles at relatively high concentration (30 mg/mL) were prepared via in situ polymerization of acrylic acid in an aqueous solution of biocompatible gelatin. These polymeric nano‐particles, in aqueous solution, had cores mainly comprised of an insoluble inter‐polymer complex of poly(acrylic acid, PAA) and gelatin and shells comprised of soluble gelatin (denoted as gelatin/PAA nano‐particles). Dynamic light scattering and electrophoretic light scattering techniques were used to trace the in situ polymerization process. The structure of the gelatin/PAA nano‐particle was further locked‐in via shell crosslinking; i.e., the reaction between glutaraldehyde and gelatin. Scanning force microscopy (SFM) was used to observe the morphologies of the particles before and after cross‐linking. Furthermore, the pH responsive behaviors of the gelatin/PAA nano‐particles before and after shell crosslinking were studied.     

Preparation of CO2/N2‐Triggered Reversibly Coagulatable and Redispersible Polyacrylate Latexes by Emulsion Polymerization Using a Polymeric Surfactant

We report here a novel approach for making reversibly coagulatable and redispersible polyacrylate latexes by emulsion (co)polymerization of methyl methacrylate (MMA) using a polymeric surfactant, poly(2‐(dimethylamino)ethyl methacrylate)₁₀‐block‐poly(methyl methacrylate)₁₄. The surfactant was protonated with HCl prior to use. The resulted PMMA latexes were readily coagulated with trace amount of caustic soda. The coagulated latex particles, after washing with deionized water, could be redispersed into fresh water to form stable latexes again by CO₂ bubbling with ultrasonication. The recovered latexes could then be coagulated by N₂ bubbling with gentle heating. These coagulation and redispersion processes were repeatable by the CO₂/N₂ bubbling.     

Surface modification of polystyrene latex particles via atom transfer radical polymerization

The atom transfer radical polymerization (ATRP) technique using the copper halide/ N,N′,N′,N″,N″‐pentamethyldiethylenetriamine complex was applied to the graft polymerization of methyl methacrylate and methyl acrylate on the uniform polystyrene (PS) seed particles and formed novel core‐shell particles. The core was submicron crosslinked PS particles that were prepared via emulsifier‐free emulsion polymerization. The crosslinked PS particles obtained were transferred into the organic phase (tetrahydrofuran), and surface modification using the chloromethylation method was performed. Then, the modified seed PS particles were used to initiate ATRP to prepare a controlled poly(methyl methacrylate) (PMMA) and poly(methyl acrylate) (PMA) shell. The final core‐shell particles were characterized using Fourier transform infrared spectroscopy, nuclear magnetic resonance, scanning electron microscopy, thermogravimetric analysis, and elementary analysis. The grafting polymerization was conducted successfully on the surface of modified crosslinked PS particles, and the shell thickness and weight ratio (PMMA and PMA) of the particles were calculated. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 892–900, 2002; DOI 10.1002/pola.10160     

New Route to Smart Core‐Shell Polymeric Microgels: Synthesis and Properties

Summary: A new method has been developed to prepare smart polymeric microgels that consist of well‐defined temperature‐sensitive cores with pH‐sensitive shells. The microgels were obtained directly from aqueous graft copolymerizations of N‐isopropylacrylamide and N,N‐methylenebisacrylamide from water‐soluble polymers containing amino groups such as poly(ethyleneimine) and chitosan. The gel diameters ranged from 300 to 400 nm. The unique core‐shell nanostructures, which had narrow size distributions, exhibited tuneable responses to pH and temperature.

Transmission electron micrograph of the poly(N‐isopropylacrylamide)/chitosan core‐shell microgels.     

Synthesis and characterization of amphiphilic heterograft copolymers with PAA and PS side chains via “Grafting from” approach

The amphiphilic heterograft copolymers poly(methyl methacrylate‐co‐2‐(2‐bromoisobutyryloxy)ethyl methacrylate)‐graft‐(poly(acrylic acid)/polystyrene) (P(MMA‐co‐BIEM)‐g‐(PAA/PS)) were synthesized successfully by the combination of single electron transfer‐living radical polymerization (SET‐LRP), single electron transfer‐nitroxide radical coupling (SET‐NRC), atom transfer radical polymerization (ATRP), and nitroxide‐mediated polymerization (NMP) via the “grafting from” approach. First, the linear polymer backbones poly(methyl methacrylate‐co‐2‐(2‐bromoisobutyryloxy)ethyl methacrylate) (P(MMA‐co‐BIEM)) were prepared by ATRP of methyl methacrylate (MMA) and 2‐hydroxyethyl methacrylate (HEMA) and subsequent esterification of the hydroxyl groups of the HEMA units with 2‐bromoisobutyryl bromide. Then the graft copolymers poly(methyl methacrylate‐co‐2‐(2‐bromoisobutyryloxy)ethyl methacrylate)‐graft‐poly(t‐butyl acrylate) (P(MMA‐co‐BIEM)‐g‐PtBA) were prepared by SET‐LRP of t‐butyl acrylate (tBA) at room temperature in the presence of 2,2,6,6‐tetramethylpiperidin‐1‐yloxyl (TEMPO), where the capping efficiency of TEMPO was so high that nearly every TEMPO trapped one polymer radicals formed by SET. Finally, the formed alkoxyamines via SET‐NRC in the main chain were used to initiate NMP of styrene and following selectively cleavage of t‐butyl esters of the PtBA side chains afforded the amphiphilic heterograft copolymers poly(methyl methacrylate‐co‐2‐(2‐bromoisobutyryloxy)ethyl methacrylate)‐graft‐(poly(t‐butyl acrylate)/polystyrene) (P(MMA‐co–BIEM)‐g‐(PtBA/PS)). The self‐assembly behaviors of the amphiphilic heterograft copolymers P(MMA‐co–BIEM)‐g‐(PAA/PS) in aqueous solution were investigated by AFM and DLS, and the results demonstrated that the morphologies of the formed micelles were dependent on the grafting density. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Compatibilizing effect of a graft copolymer on bacterial poly(3‐hydroxybutyrate)/poly(methyl methacrylate) blends

Blends of isotactic (natural) poly(3‐hydroxybutyrate) (PHB) and poly(methyl methacrylate) (PMMA) are partially miscible, and PHB in excess of 20 wt % segregates as a partially crystalline pure phase. Copolymers containing atactic PHB chains grafted onto a PMMA backbone are used to compatibilize phase‐separated PHB/PMMA blends. Two poly(methyl methacrylate‐g‐hydroxybutyrate) [P(MMA‐g‐HB)] copolymers with different grafting densities and the same length of the grafted chain have been investigated. The copolymer with higher grafting density, containing 67 mol % hydroxybutyrate units, has a beneficial effect on the mechanical properties of PHB/PMMA blends with 30–50% PHB content, which show a remarkable increase in ductility. The main effect of copolymer addition is the inhibition of PHB crystallization. No compatibilizing effect on PHB/PMMA blends with PHB contents higher than 50% is observed with various amounts of P(MMA‐g‐HB) copolymer. In these blends, the graft copolymer is not able to prevent PHB crystallization, and the ternary PHB/PMMA/P(MMA‐g‐HB) blends remain crystalline and brittle. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1390–1399, 2002     

Synthesis of core/shell structure of glycidyl–functionalized poly(methyl methacrylate) latex nanoparticles via differential microemulsion polymerization

The differential microemulsion polymerization technique was used to synthesize the nanoparticles of glycidyl-functionalized poly(methyl methacrylate) or PMMA via a two-step process, by which the amount of sodium dodecyl sulfate (SDS) surfactant required was 1/217 of the monomer amount by weight and the surfactant/water ratio could be as low as 1/600. These surfactant levels are extremely low in comparison with those used in a conventional microemulsion polymerization system. The glycidyl-functionalized PMMA nanoparticles are composed of nanosized cores of high molecular weight PMMA and nano-thin shells of the random copolymer poly[(methyl methacrylate)-ran-(glycidyl methacrylate)]. The particle sizes were about 50 nm. The ratios of the glycidyl methacrylate in the glycidyl-functionalized PMMA were achieved at about 5–26 wt.%, depending on the reaction conditions. The molecular weight of glycidyl-functionalized PMMA was in the range of about 1 × 10⁶ to 3 × 10⁶ g mol⁻¹. The solid content of glycidyl-functionalized PMMA increased when the amount of added glycidyl methacrylate was increased. The glycidyl-functionalized polymer on the surface of nano-seed PMMA nanoparticles was a random copolymer which was confirmed by ¹H-NMR spectroscopy. The amounts of functionalization were investigated by the titration of the glycidyl functional group. The structure of the glycidyl-functionalized PMMA nanoparticles was investigated by means of TEM. The glycidyl-functionalized PMMA has two regions of T_g which are at around 90 °C and 125 °C, respectively, of which the first one was attributed to the poly[(methyl methacrylate)-ran-(glycidyl methacrylate)] and the second one was due to the PMMA. A core/shell structure of the glycidyl-functionalized PMMA latex nanoparticles was observed.     

Sequential double polymer click reactions for the preparation of regular graft copolymers

In this study, graft copolymers with regular graft points containing polystyrene (PS) backbone and poly(methyl methacrylate) (PMMA), poly(tert‐butyl acrylate) (PtBA), or poly (ethylene glycol) (PEG) side chains were simply achieved by a sequential double polymer click reactions. The linear α‐alkyne‐ω‐azide PS with an anthracene pendant unit per chain was produced via atom transfer radical polymerization of styrene initiated by anthracen‐9‐ylmethyl 2‐((2‐bromo‐2‐methylpropanoyloxy)methyl)‐2‐methyl‐3‐oxo‐3‐(prop‐2‐ynyloxy) propyl succinate. Subsequently, the azide–alkyne click coupling of this PS to create the linear multiblock PS chain with pendant anthracene sites per PS block, followed by Diels–Alder click reaction with maleimide end‐functionalized PMMA, PtBA, or PEG yielded final PS‐g‐PMMA, PS‐g‐PtBA or PS‐g‐PEG copolymers with regular grafts, respectively. Well‐defined polymers were characterized by ¹H NMR, gel permeation chromatography (GPC) and triple detection GPC. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of poly[(2‐oxo‐1,3‐dioxolane‐4‐yl) methyl methacrylate‐co‐ethyl acrylate] by incorporation of carbon dioxide into epoxide polymer and the miscibility behavior of its blends with poly(methyl methacrylate) or poly(vinyl chloride)

This study was related to the investigation of the chemical fixation of carbon dioxide to a copolymer bearing epoxide and the application of the cyclic carbonate group containing copolymer‐to‐polymer blends. In the synthesis of poly[(2‐oxo‐1,3‐dioxolane‐4‐yl) methyl methacrylate‐co‐ethyl acrylate] [poly(DOMA‐co‐EA)] from poly(glycidyl methacrylate‐co‐ethyl acrylate) [poly(GMA‐co‐EA)] and CO₂, quaternary ammonium salts showed good catalytic activity. The films of poly(DOMA‐co‐EA) with poly(methyl methacrylate) (PMMA) or poly(vinyl chloride) (PVC) blends were cast from N,N′‐dimethylformamide solution. The miscibility of the blends of poly(DOMA‐co‐EA) with PMMA or PVC have been investigated both by DSC and visual inspection of the blends. The optical clarity test and DSC analysis showed that poly(DOMA‐co‐EA) containing blends were miscible over the whole composition range. The miscibility behaviors were discussed in terms of Fourier transform infrared spectra and interaction parameters based on the binary interaction model. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1472–1480, 2001     

Synthesis of poly[(2‐oxo‐1,3‐dioxolane‐ 4‐yl)methyl methacrylate‐co‐styrene] by addition reaction of carbon dioxide and its compatibility with poly(methyl methacrylate) or poly(vinyl chloride)

We investigated the chemical fixation of carbon dioxide (CO ₂) to a copolymer bearing epoxide and the application of the cyclic carbonate group containing copolymer to polymer blends. In the synthesis of poly[(2‐oxo‐1,3‐dioxolane‐4‐yl)methyl methacrylate‐co‐styrene] [poly(DOMA‐co‐St)] from the addition of CO ₂ to poly(glycidyl methacrylate‐co‐styrene) [poly(GMA‐co‐St)], quaternary ammonium salts showed good catalytic activity at mild reaction conditions. The CO ₂ addition reaction followed pseudo first‐order kinetics with the concentration of poly(GMA‐co‐St). In order to expand the applications of the CO ₂ fixed copolymer, polymer blends of this copolymer with poly(methyl methacrylate) (PMMA) or poly(vinyl chloride) (PVC) were cast from N,N′‐dimethylformamide (DMF) solution. Miscibility of blends of poly(DOMA‐co‐St) with PMMA or PVC have been investigated both by differential scanning calorimetry (DSC) and visual inspection of the blends, and the blends were miscible over the whole composition ranges. The miscibility behaviors were also discussed in terms of FT‐IR spectra. Copyright © 2002 John Wiley & Sons, Ltd.     

Synthesis and swelling behavior of amphiphilic comb‐like branched polymer (AA‐co‐CMS)‐g‐PMMA

Copolymerization of acrylic acid and p‐chloromethylstyrene (p‐CMS) in dioxane initiated with α,α′‐azobisisobutyronitrile was carried out to produce macroinitiator P(AA‐co‐CMS) containing PhCH₂Cl group at 65°C. Then methyl methacrylate was grafted onto P(AA‐co‐CMS) backbone using PhCH₂Cl group as an initiation site and FeCl₂/triphenyl phosphine complex as a catalyst. The resulted copolymer (AA‐co‐CMS)‐g‐PMMA with a comb‐like branched structure has a hydrophilic backbone (PAA) and hydrophobic side chains (PMMA). Compositions and structures of macroinitiator and the grafted product of P(AA‐co‐CMS)‐g‐PMMA were determined by ¹H‐NMR, infrared (IR), and gel permeation chromatography (GPC). The average graft number, the average length of branch chains, the graft ratio, and the graft efficiency were investigated. The swelling behavior of the comb‐like branched polymer was also investigated. The gradual increase of swelling ratios was accompanied by an increase of pH and temperature. The kinetic exponents indicated that the swelling transport mechanisms transformed from Fickian diffusion to non‐Fickian transport as the decreasing pH. Copyright © 2009 John Wiley & Sons, Ltd.     

Dispersion polymerization of MMA in supercritical CO2 stabilized by random copolymers of 1H,1H–perfluorooctyl methacrylate and 2‐(dimethylaminoethyl methacrylate)

A series of random copolymers, composed of 1H,1H‐perfluorooctyl methacrylate (FOMA) and 2‐dimethylaminoethyl methacrylate (DMAEMA) were prepared as stabilizers for the dispersion polymerization of methyl methacrylate in supercritical CO₂ (scCO₂). Free‐flowing, spherical poly(methyl methacrylate) (PMMA) particles were produced in high yield by the effective stabilization of poly(FOMA‐co‐DMAEMA) containing 34–67 w/w % (15–41 m/m %) FOMA structural units. Less stabilized but micron‐sized discrete particles could be obtained even with 25 w/w % (10 m/m %) FOMA stabilizer. The result showed that the composition of copolymeric stabilizers had a dramatic effect on the size and morphology of PMMA. The particle size was controllable with the surfactant concentration. The effect of the monomer concentration and the initial pressure on the polymerization was also investigated. The dry polymer powder obtained from dispersion polymerization could be redispersed to form stable aqueous latexes in an acidic buffered solution (pH = 2.1) by an electrostatic stabilization mechanism due to the ionization of DMAEMA units in the stabilizer. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1365–1375, 2008     

Nanosphere formation in copolymerization of methyl methacrylate with poly(ethylene glycol) macromonomers

Polymeric nanospheres consisting of poly(methyl methacrylate) (PMMA) cores and poly(ethylene glycol) (PEG) branches on their surfaces were prepared by free radical copolymerization of methyl methacrylate (MMA) with PEG macromonomers in ethanol/water mixed solvents. PEG macromonomers having a methacryloyl (MMA‐PEG) and p‐vinylbenzyl (St‐PEG) end group were used. It has become clear that the obtained polymer dispersions form three kinds of states, particle dispersion (milky solution), clear solution, and gel/precipitation. It was found that the reaction parameters such as MMA concentration, molecular weight, and concentration of PEG macromonomers, and water content can affect nanosphere formation in a copolymerization system. The water volume fraction of mixed ethanol/water solvents affected the particle size of the nanospheres. These differences in the formation of nanospheres were due to the solvophilic/solvophobic balance between the copolymers and solvents during the self‐assembling process of the copolymers. The sizes of nanospheres can be controlled by varying concentration of PEG macromonomer and water content in solvents. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1811–1817, 2000     

Preparation of PMMA/acid-modified chitosan core-shell nanoparticles and their potential as gene carriers

The core-shell nanoparticles consisting of poly(methyl methacrylate) (PMMA) cores surrounded by various acid-modified chitosan shells were synthesized using a surfactant-free emulsion copolymerization, induced by a tert-butylhydroperoxide (TBHP) solution. Methyl methacrylate (MMA) was grafted onto four acid-modified chitosans (hydrochloric, lactic, aspartic, and glutamic acids) with MMA conversions up to 64%. The prepared nanoparticles had diameter ranging from 100 to 300 nm characterized by atomic force microscopy and displayed highly positive surface charges up to +77 mV. Transmission electron microscopic images clearly revealed well-defined core-shell morphology of the nanoparticles where PMMA cores were coated with acid-modified chitosan shells. The effect of acid-modified chitosans on particle size, intensity of surface charge, morphology, and thermal stability were determined systematically. The plasmid DNA/nanoparticles complexes were investigated with ζ-potential measurement. The results suggested that these nanoparticles can effectively complex with plasmid DNAs via electrostatic interaction and could be used as gene carriers.

Self‐assembly behavior of amphiphilic linear‐block‐dendritic copolymers with long subchains: Dependences on dendron generation and mixing dynamics

Block copolymers composed of acrylic acid and methyl methacrylate with three topologies of double linear blocks, poly(acrylic acid) (PAA) linear block/poly(methyl methacrylate) (PMMA) G1‐dendron and PAA linear block/PMMA G2‐dendron have been prepared by the combination of atom transfer radical polymerization and azide–alkyne click reaction. Proton nuclear magnetic resonance spectroscopy, Fourier transform infrared spectroscopy, and gel permeation chromatography have been adopted thoroughly to identify the chemical structure of those block copolymers with expected topologies. The self‐assembly of those block copolymers in the selective solvent has been performed through two mixing routes of gentle and abrupt variation in solvent selectivity, and the morphology of the obtained self‐assemblies/aggregates was observed by transmission electron microscopy. Because the abrupt variation route altered sharply the solvent quality during the mixing, the intermolecular association of polymer chains resulted in the smaller self‐assemblies but the further growth of smaller self‐assemblies was not observed. On the contrary, the gentle variation route changed gradually the solvent quality during the mixing, favoring not only the intermolecular association but also the further growth of self‐assemblies to result in larger aggregates. The final morphology of those assemblies/aggregates also exhibited the dependence of PMMA dendron generation. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1446–1456     

Microsphere synthesis by dispersion copolymerization of methyl methacrylate with poly(acrylic acid) macromonomers: pH effect on microsphere formation

The pH effect on microsphere formation in the dispersion copolymerization of methyl methacrylate with vinylbenzyl-terminated poly(acrylic acid) (PAA) macromonomers is studied. The diameter of poly(methyl methacrylate) (PMMA) microspheres is minimum around pH = 8. Dynamic light scattering data indicate that the shell thickness of PAA-grafted chains shows a maximum around this pH. The degree of expansion of PAA chains drastically affects the particle size of PMMA microspheres during the dispersion copolymerization.     

Effect of graft polymer on the formation of micron-sized,monodisperse, "onion-like" alternately multilayered poly(methyl methacrylate)/polystyrene composite particles by reconstruction of morphology with the solvent-absorbing/releasing method

Some factors contributing to the formation of an alternately multilayered structure of micron-sized, monodisperse poly(methyl methacrylate) (PMMA)/polystyrene (PS) (1/1, w/w) composite particles by reconstruction of the morphology with the solvent-absorbing/releasing method (SARM) were discussed. The original composite particles, which were produced by seeded dispersion polymerization (SDP) of styrene, had a core–shell structure. When PS/PMMA (1/1, w/w) composite particles produced by SDP of methyl methacrylate were treated by the SARM with toluene, the reconstructed morphology of the composite particles was not the multilayered structure but a hemisphere (or core–shell). The PS/PMMA composite particle contained less than 10 wt% PMMA- g-PS. On the other hand, the PMMA/PS composite particles contained about 40 wt% graft polymer. The graft polymer would exist at the interfaces of the alternate multilayers and decrease their interfacial energy. This was the main reason why the alternately multilayered structure was constructed by the SARM, though the total interfacial area between PMMA and PS layers in the multilayered particle is much larger than that of the hemisphere (or core–shell).