Synthesis and characterization of materials prepared via the copolymerization of ethylene with 1‐octadecene and norbornene using a [(π‐cyano‐nacnac)Cp] zirconium complex

[3‐Cyano‐2‐(2,6‐diisopropylphenyl)aminopent‐2‐en‐4‐(phenylimine)tris (pentafluorophenyl)borate](η⁵‐C₅H₅)ZrCl₂, [(B(C₆F₅)₃‐ NC‐nacnac)CpZrCl₂], precatalyst ( 2 ) can be treated with low concentrations of methylaluminoxane (MAO) to generate active sites capable of copolymerizing ethylene with 1‐octadecene or norbornene under mild conditions. A series of poly(ethylene‐co‐octadecene) and poly(ethylene‐co‐norbornene) copolymers were prepared, and their properties were characterized by NMR, differential scanning calorimetry, and mechanical analysis. The results show that this system produced poly(ethylene‐co‐octadecene) copolymers with a branching content of about 8 mol %. However, upon increasing the comonomer concentration, a drastic reduction in the M_n of the product is observed concomitant with an increase in comonomer incorporation. This leads to a gradual decrease in Young's modulus and stress at break, indicating an increase in the “softness” of the copolymer. In the case of copolymerizations of ethylene and norbornene, the catalytic system ( 2 /MAO) shows a substantial decrease in reactivity in the presence of norbornene and generates copolymer chains in which 5–10 mol % norbornene is in blocks. We also observe that ethylene norbornene copolymers exhibit a high degree of alternating insertions (close to 50%), as determined by NMR spectroscopy. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Side‐chain crystallization behavior of graft copolymers consisting of amorphous main chain and crystalline side chains: Poly(methyl methacrylate)‐graft‐poly(ethylene glycol) and poly(methyl acrylate)‐graft‐poly(ethylene glycol)

Graft copolymers consisting of amorphous main chain, poly(methyl methacrylate) (PMMA), or poly(methyl acrylate) (PMAc), and crystalline side chains, poly(ethylene glycol) (PEG), have been prepared by copolymerization of PEG macromonomers with methyl methacrylate or methyl acrylate (MMAx or MACx, respectively). Because of the compatibility of PMMA/PEG and PMAc/PEG, from small‐angle X‐ray scattering results, the main and side chains in graft copolymers were suggested to be homogeneous in the molten state. Differential scanning calorimetry (DSC) cooling scans revealed that PEG side chains for graft copolymers with large PEG fractions were crystallized when the sample was cooled, with a cooling rate of 10 °C/min. The spherulite pattern observed by a polarized optical microscope suggested the growth of PEG crystalline lamellae. Crystallization of PEG in MMAx was more restrained than in MACx. From these results, we have concluded that the crystallization behavior of the grafted side chains is strongly influenced by the glass transition of a homogeneously molten sample as well as dilution of the crystallizable chains. Domain spacings for isothermally crystallized graft copolymers were described by interdigitating chain packing in crystalline–amorphous lamellar structure. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 79–86, 2005     

Synthesis and characterization of polystyrene‐b‐poly (1,2‐isoprene‐ran‐3,4‐isoprene) block copolymers with azobenzene side groups

Polystyrene‐b‐poly(1,2‐isoprene‐ran‐3,4‐isoprene) block copolymers with azobenzene side groups were synthesized by the esterification of azobenzene acid chloride with polystyrene‐b‐hydroxylated poly(1,2‐isoprene‐ran‐3,4‐isopenre) block copolymers for creating new photochromic materials. The resulting block copolymers with azobenzene side groups were characterized for structural, thermal, and morphological properties. IR and NMR spectroscopies confirmed that the polymers obtained had the expected structures. Differential scanning calorimetric measurements by heating runs clearly showed the glass transitions of polystyrene and polyisoprene main chains and two distinct first‐order transitions at temperatures of azobenzene side groups around 48 and 83 °C. The microstructure of these block copolymer films was investigated using both transmission electron microscopy (TEM) and near‐field optical microscopy (NOM). TEM images revealed typical microphase‐separated morphologies such as sphere, cylinder, and lamellar structures. The domain spacing of microphase‐separated cylindrical morphology in the NOM image agreed with that of the TEM results. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2406–2414, 2002     

Correlation of the melting behavior and copolymer composition distribution of Ziegler–Natta‐catalyst and single‐site‐catalyst polyethylene copolymers

The multimodal differential scanning calorimetry melting endotherms observed for commercial linear low‐density polyethylenes are due to broad and multimodal short‐chain‐branching distributions. Multiple peaks, observed in melting endotherms of isothermally melt‐crystallized and compositionally homogeneous polyethylene copolymers are due to intrachain heterogeneity. This intrachain heterogeneity is quantified by the distribution of ethylene sequence lengths within the chains. These compositionally homogeneous copolymers undergo a primary crystallization, which produces a population of thicker lamellae, creating a network that places severe restrictions on segment transport in subsequent secondary crystallization, which produces a population of thinner crystals. The restrictions on segment transport imposed by the initial network created by the primary crystallization of thicker lamellae severely limits the total crystallinity achieved in the random copolymers studied. The solution crystallization of such copolymers produces a continuous distribution due to more facile segment transport in a dilute solution, in contradistinction to the multimodal distribution produced in the melt crystallization. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2800–2818, 2001     

Controlled copolymerization of vinyl acetate with 1‐alkenes and their fluoro derivatives by degenerative transfer

The degenerative transfer copolymerization of vinyl acetate with ethene and higher 1‐alkenes, as well as their fluoro derivatives (R_fCH?CH₂), under mild conditions was carried out using AIBN as the initiator and ethyl iodoacetate as the control agent. The obtained random copolymers were fairly high in alkene content, with high molecular weights and relatively narrow polydispersities. The quasi‐living nature of the copolymerization allowed the synthesis of a block terpolymer by sequential addition of two different 1‐alkene comonomers to a vinyl acetate copolymerization system. The fluorinated side chains of vinyl acetate/fluoro alkene copolymers segregate toward the air‐side of thin films, resulting in advancing water contact angle as high as 114°. 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3728–3736, 2005     

Synthesis of polyallene‐based graft copolymer via 6‐methyl‐1,2‐heptadien‐4‐ol and styrene

A series of well‐defined graft copolymers with a polyallene‐based backbone and polystyrene side chains were synthesized by the combination of living coordination polymerization of 6‐methyl‐1,2‐heptadien‐4‐ol and atom transfer radical polymerization (ATRP) of styrene. Poly(alcohol) with polyallene repeating units were prepared via 6‐methyl‐1,2‐heptadien‐4‐ol by living coordination polymerization initiated by [(η³‐allyl)NiOCOCF₃]₂ firstly, followed by transforming the pendant hydroxyl groups into halogen‐containing ATRP initiation groups. Grafting‐from route was employed in the following step for the synthesis of the well‐defined graft copolymer: polystyrene was grafted to the backbone via ATRP of styrene. The cleaved polystyrene side chains show a narrow molecular weight distribution (M_w/M_n = 1.06). This kind of graft copolymer is the first example of graft copolymer via allene derivative and styrenic monomer. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5509–5517, 2007     

NMR investigation of effect of dissolved salts on the thermoresponsive behavior of oligo(ethylene glycol)‐methacrylate‐based polymers

The synthesis of thermo‐ and ionic‐responsive copolymers based on polyethylene glycol methyl ether methacrylate (OEGMA) and 2,2,2‐trifluoroethyl acrylate (TFEA) via reversible addition‐fragmentation chain transfer polymerization is described. Reactivity ratios for the copolymerization of OEGMA and TFEA are r_OEGMA = 2.46 and r_TFEA = 0.22, indicating that OEGMA is incorporated more rapidly than TFEA monomers. The copolymers are thermosensitive and exhibit volume phase transitions (lower critical solution behavior) at temperature, which depend on copolymer composition and the presence of added salts in the aqueous solutions. It was found that the copolymers exhibited LCST transitions at temperatures below 353 K only in salt solutions. ¹H NMR measurements indicated that motion of the protons located in and near the hydrophobic main chain are more sensitive to temperature than protons in the hydrophilic OEGMA side chains. The hydrophilic side chains remain largely hydrated; however, the presence of two distinct conformations of the terminal groups of the side chains was confirmed. The influence of OEGMA side chain length, copolymer composition, and salt type on aggregation behavior and dynamics was examined in detail. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2375–2385     

Poly(epichlorohydrin) modified with 3,4,5‐tris(dodecyloxy)benzoate: The structure and dynamics of the aliphatic side chains in the columnar mesophase

We investigated the dynamics and structure of the aliphatic side chains of a randomly grafted copolymer, obtained through the chemical modification of poly(epichlorohydrin) with potassium 3,4,5‐tris(dodecyloxy)benzoate, with solid‐state ¹³C NMR. Below 283 K, the aliphatic chains partially crystallized in an all‐anti conformation. The calorimetric data were compatible with an orthorhombic packing. Below 323 K, the polymer exhibited a columnar mesophase. Spin–lattice relaxation times were determined in this temperature range and at 333 K, that is, in the isotropic phase. In the liquid‐crystalline state, some carbons exhibited a double decay in the spin–lattice relaxation, and this was attributed to presence of the liquid‐crystalline phase. This hypothesis was supported by a conformational analysis performed by molecular modeling. The activation energies of the relaxation processes in the mesophase were also estimated. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2099–2111, 2005     

Polydispersity of ethylene sequence length in metallocene ethylene/α‐olefin copolymers. I. Characterized by thermal‐fractionation technique

In this article, the polydispersity of the ethylene sequence length (ESL) in ethylene/α‐olefin copolymers was studied by atomic force microscopy (AFM) and the thermal‐fractionation technique. The crystal morphology observation by AFM showed that morphology changed gradually with decreasing average ESL from complete lamellae over shorter and more curved lamellae to a granular‐like morphology, and the mixed morphology was observed after stepwise crystallization from phase‐separated melt. This result indicated that the ethylene sequence with different lengths crystallized into a crystalline phase with a different size and stability at the copolymer systems. The thermal‐fractionation technique was used to characterize the polydispersity of ESL. Three of the following statistical terms were introduced to describe the distribution of ESL and the lamellar thickness: the arithmetic mean L?_n, the weight mean L?_w, and the broadness index I = L?_w/L?_n. It was concluded that the polydispersity of ESL could be quantitatively characterized by the thermal‐fractionation technique. The effects of temperature range, temperature‐dependent specific heat capacity C_p of copolymer, and the molecular weight on the results of thermal fractionation were discussed. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 813–821, 2002     

Synthesis and properties of gradient copolymers based on 2‐phenyl‐2‐oxazoline and 2‐nonyl‐2‐oxazoline

In this study, the structure–property relationships for a series of statistical 2‐nonyl‐2‐oxazoline (NonOx) and 2‐phenyl‐2‐oxazoline (PhOx) copolymers were investigated for the first time. The copolymerization kinetics were studied and the reactivity ratios were calculated to be r_NonOx = 7.1 ± 1.4 and r_PhOx = 0.02 ± 0.1 revealing the formation of gradient copolymers. The synthesis of a systematical series of NonOx–PhOx copolymers is described, whereby the amount of NonOx was increased in steps of 10 mol %. The thermal and surface properties were investigated for this series of well‐defined copolymers. The thermal properties revealed a linear decrease in glass transition temperature for copolymers containing up to 39 wt % NonOx. Furthermore, the melting temperature of the copolymers containing 0 to 55 wt % PhOx linearly decreased most likely due to disturbance of the NonOx crystalline domains by incorporation of PhOx in the NonOx part of the copolymer. The surface energies of spincoated polymer films revealed a strong decrease in surface energy upon incorporation of NonOx in the copolymers due to strong phase separation between NonOx and PhOx allowing the NonOx chains to orient to the surface. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6433–6440, 2009     

Chain composition dependence of luminescence properties for copolymers of 2‐methoxy‐5‐2′‐ethyl‐hexyloxy‐1,4‐phenylenevinylene and 2,3‐diphenyl‐5‐octyl‐1,4‐phenylenevinylene

The copolymers of 2‐methoxy‐5‐2′‐ethyl‐hexyloxy‐1,4‐phenylenevinylene (MEH‐PV) and 2,3‐diphenyl‐5‐octyl‐1,4‐phenylenevinylene were prepared via the Gilch route with their chain compositions and the reactivity ratios of the monomers estimated by ¹H NMR spectroscopy. The results indicated that the copolymers tended to form an alternative copolymer as the feed ratio of the monomers closed to one‐half. When an individual copolymer solution in tetrahydrofuran was spun‐cast to form a film, the MEH‐PV units were able to attract the like units from the adjacent chains. As a result, the ultraviolet–visible absorption spectrum of the alternative copolymer in film form was broader than the spectra of those with different compositions. The photoluminescence spectra of the copolymers in film form exhibited the characteristic shoulder of poly(2‐methoxy‐5‐2′‐ethyl‐hexyloxy‐1,4‐phenylenevinylene), even though the content of MEH‐PV units was not great enough for the formation of repeat units in sequence. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2180–2186, 2003     

Synthesis and characterization of donor–acceptor poly(3‐hexylthiophene) copolymers presenting 1,3,4‐oxadiazole units and their application to photovoltaic cells

We have used Grignard metathesis polymerization to prepare poly(3‐hexylthiophene)‐based copolymers containing electron‐withdrawing 4‐tert‐butylphenyl‐1,3,4‐oxadiazole‐phenyl moieties as side chains. We characterized these copolymers using ¹H and ¹³C nuclear magnetic resonance spectroscopy, thermogravimetric analysis, and gel permeation chromatography. The band gap energy of copolymer was determined from the onset of the optical absorption. The quenching effects were observed in the photoluminescence spectra of the copolymers incorporating pendant electron‐deficient 1,3,4‐oxadiazole moieties on the side chains. The photocurrents of devices were enhanced in the presence of an optimal amount of the 1,3,4‐oxadiazole moieties, thereby leading to improved power conversion efficiencies. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3331–3339, 2010     

Homo‐ and copolymerization of ethylene and norbornene with bis(β‐diketiminato) titanium complexes activated with methylaluminoxane

Homo‐ and copolymerization of ethylene and norbornene were investigated with bis(β‐diketiminato) titanium complexes [ArNC(CR₃)CHC(CR₃)NAr]₂TiCl₂ (R = F, Ar = 2,6‐diisopropylphenyl 2a; R = F, Ar = 2,6‐dimethylphenyl 2b ; R = H, Ar = 2,6‐diisopropylphenyl 2c ; R = H, Ar = 2,6‐dimethylphenyl 2d) in the presence of methylaluminoxane (MAO). The influence of steric and electric effects of complexes on catalytic activity was evaluated. With MAO as cocatalyst, complexes 2a–d are moderately active catalysts for ethylene polymerization producing high‐molecular weight polyethylenes bearing linear structures, but low active catalysts for norbornene polymerization. Moreover, 2a – d are also active ethylene–norbornene (E–N) copolymerization catalysts. The incorporation of norbornene in the E–N copolymer could be controlled by varying the charged norbornene. ¹³C NMR analyses showed the microstructures of the E–N copolymers were predominantly alternated and isolated norbornene units in copolymer, dyad, and triad sequences of norbornene were detected in the E–N copolymers with high incorporated content of norbornene. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 93–101, 2008     

Long‐chain‐branched polyethene by the copolymerization of ethene and nonconjugated α,ω‐dienes

Ethene was copolymerized (1) with 1,5‐hexadiene with rac‐ethylenebis(indenyl)zirconium dichloride/methylaluminoxane (MAO) used as a catalyst and (2) with 1,7‐octadiene with bis(n‐butylcyclopentadienyl)zirconium dichloride/MAO and rac‐ethylenebis(indenyl)hafnium dichloride (Et[Ind]₂HfCl₂)/MAO used as catalysts at 80 °C in toluene. The copolymer microstructure and the influence of diene incorporation on the rheological properties were examined. Ethene and 1,5‐hexadiene formed a copolymer in which a major fraction of the 1,5‐hexadiene was incorporated into rings and a small fraction formed 1‐butenyl branches. The copolymerization of ethene with 1,7‐octadiene resulted in a higher selectivity toward branch formation. Some of the branches formed long‐chain‐branching (LCB) structures. The ring formation selectivity increased with decreasing ethene concentration in the polymerization reactor. Melt rheological properties of the diene copolymers resembled those of metallocene‐catalyzed LCB homopolyethenes and depended on the vinyl content, the catalyst, and the polymerization conditions. At high diene contents, all three catalysts produced crosslinked polyethene. This was especially pronounced with Et[Ind]₂HfCl₂, where only 0.2 mol % 1,7‐octadiene in the copolymer was required to achieve significantly modified rheological properties. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3805–3817, 2001     

Synthesis and characterization of polytulipalin‐g‐polylactide copolymers

Graft copolymers of poly(tulipalin A) (PT) and poly(DL‐lactide) (PDLLA) (PT‐g‐PDLLA) having various graft lengths and ratios were synthesized by free‐radical copolymerization of α‐methylene‐γ‐butyrolactone (MBL) and PDLLA macromonomers (HEMA‐PDLLA) terminated by 2‐hydroxyethyl methacrylate (HEMA)‐terminated. HEMA‐PDLLA were synthesized by ring opening polymerization (ROP) of DL‐lactide in the presence of HEMA. Both HEMA‐PDLLA and the copolymers were characterized by NMR spectroscopy and gel permeation chromatography (GPC). The thermal properties of the graft copolymers were found to depend on the graft length and the ratio. The copolymers consisting of PDLLA side chains of M_n = 500 Da showed a single T_g between T_gs of the two component polymers, suggesting a miscible state of PT and PDLLA. In contrast, the copolymers consisting of PDLLA side chains of M_n = 1100, 2000, and 7000 Da showed two isolated T_g, suggesting two segregated domains. The AFM phase images of the copolymers supported the single and phase‐separated morphologies for the former and latter systems, respectively. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Copolymerization of propylene with higher α‐olefins in the presence of the syndiospecific catalyst i‐Pr(Cp)(9‐Flu)ZrCl2/MAO

The catalyst system i‐Pr(Cp)(9‐Flu)ZrCl₂/methylaluminoxane was used for the synthesis of random syndiotactic copolymers of propylene with 1‐hexene, 1‐dodecene, and 1‐octadecene as comonomers. An investigation of the microstructure by ¹³C NMR spectroscopy revealed that the stereoregularity of the copolymers decreased because of an increase in skipped insertions in the presence of the higher 1‐olefin. The melting temperature of the copolymers, as measured by differential scanning calorimetry (DSC), decreased linearly with increasing comonomer content independently of the comonomer nature. During the DSC heating cycle, an exothermic peak indicating a crystallization process was observed. The decrease in the crystallization temperature with higher 1‐olefin content, measured by crystallization analysis fractionation, indicated a small but significant dependence on the nature of the comonomer. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 128–140, 2002     

Radical copolymerization of chlorotrifluoroethylene with 4‐bromo‐3,3,4,4‐tetrafluorobut‐1‐ene

The radical copolymerization of chlorotrifluoroethylene (CTFE) with 3,3,4,4‐tetrafluoro‐4‐bromobut‐1‐ene (BTFB) initiated by tert‐butylperoxypivalate is presented. The microstructures of the obtained copolymers are determined by means of NMR spectroscopies and elemental analysis and show that random copolymers were obtained. A wide range of poly(CTFE‐co‐BTFB) copolymers is synthesized, containing from 17 to 89 mol % of CTFE. In all the cases, CTFE is the less reactive of both comonomers. T_d^10% values, ranging from 163 up to 359 °C, are dependent on the BTFB content. These variations of thermal property are attributed to the increase in the number of C‐H and C‐Br bonds breakdown when the BTFB molar percentage in the copolymer is higher. T_g values range from 19 to 39 °C and a decreasing trend is observed when increasing the amount of BTFB in the copolymer. This observation arises from the higher flexibility of the copolymer when increasing the number of fluorobrominated lateral chains. These original fluoropolymers bearing reactive pendant bromo groups are suitable candidates for various applications. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1714–1720     

Synthesis,complex formation,and dilute‐solution associative behavior of linear poly(methacrylic acid)‐graft‐poly(2‐ethyl‐2‐oxazoline)*

Poly(methacrylic acid) (PMA) and poly(2‐ethyl‐2‐oxazoline) (PEOZO) are a polyacid/polybase pair capable of forming reversible, pH‐responsive, hydrogen‐bonding complexes stabilized by hydrophobic effects in aqueous media. Linear PMA was modified with long‐chain (number‐average molecular weight: 10,000) PEOZO via statistical coupling reactions in organic media to prepare a series of PMA‐graft‐PEOZO copolymers. Potentiometric titrations revealed that the presence of tethered PEOZO markedly increases the pK_a values for PMA‐g‐PEOZO copolymers as compared with simple PMA/PEOZO mixtures at degrees of ionization, α, between 0.0 and 0.1. The dilute‐solution PMA–PEOZO intramolecular association has been probed by monitoring the PEOZO NMR spin–spin (T₂) relaxation as a function of pH. Covalently attached PEOZO side chains participate in complexation at higher values of α than untethered PEOZO. Surprisingly, most PEOZO side chains did not take part in hydrogen bonding at low α, and the highest level of PEOZO incorporation induced a decrease in the number of PMA/PEOZO hydrogen bonds. The polymer self‐diffusion as a function of α was measured with dynamic light scattering. At low pH, the copolymers had no charge and they were in a collapsed form. At high pH, the expected conformational expansion of the PMA units was enhanced at moderate levels of PEOZO incorporation. However, the highest PEOZO incorporation induced the onset of intramolecular associations between PEOZO units along the copolymer chains. Low shear rheometry and light scattering measurements were used in conjunction with the T₂ NMR measurements to propose a model consistent with the aforementioned behavior. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2520–2533, 2004     

Pendant side‐chain sterics against electrostatic forces: Influencing short‐range ordering in random polyelectrolytes

The length of pendant side chains in charged, random, comb‐shaped polymers dictates the nature of their short‐range ordering. Random copolymers, and terpolymer, of 4‐vinylpyridine (4VP), styrene, and isoprene were synthesized and subsequently fully quaternized with 1‐alkylbromides having varying number of carbons on the alkyl group ranging from 2 to 8. Evaluation by wide angle X‐ray scattering revealed that dipole–dipole attraction facilitates the formation of ionomer cluster morphology in samples with two carbons on the pendant side chain, whereas for samples with four or more carbons on the pendant side chains, side‐chain sterics was dominant resulting in periodic backbone spacing. Copolymers with isoprene, having flexible backbones, favor the formation of ionomer cluster morphology while styrene copolymers having rigid backbones disfavor the formation of ionomer clusters. An “in‐line” dipole model was developed to predict the separation distance at which both ionomer cluster and backbone–backbone morphologies could coexist. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1325–1336     

Poly(ethylene imine)‐graft‐poly(ethylene oxide) brush‐like copolymers: Preparation,thermal properties,and selective supramolecular inclusion complexation with α‐cyclodextrin

Poly(ethylene imine)‐graft‐poly(ethylene oxide) (PEI‐g‐PEO) copolymers were synthesized via Michael addition reaction between acryl‐terminated poly(ethylene oxide) methyl ether (PEO) and poly(ethylene imine) (PEI). The brush‐like copolymers were characterized by means of Fourier transform infrared spectroscopy and nuclear magnetic resonance spectroscopy. It is found that the crystallinity of the PEO side chains in the copolymers remained unaffected by the PEI backbone whereas the crystal structure of PEO side chains was altered to some extent by the PEI backbone. The crystallization behavior of PEO blocks in the copolymers suggests that the bush‐shaped copolymers are microphase‐separated in the molten state. The PEO side chains of the copolymers were selectively complexed with α‐cyclodextrin (α‐CD) to afford hydrophobic side chains (i.e., PEO/α‐CD inclusion complexes). The X‐ray diffraction (XRD) shows that the inclusion complexes (ICs) of the PEO side chains displayed a channel‐type crystalline structure. It is identified that the stoichiometry of the inclusion complexation of the PEI‐g‐PEO with α‐CD is close to that of the control PEO with α‐CD. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2296–2306, 2008