Titanium‐mediated living radical styrene polymerizations. V. Cp2TiCl‐catalyzed initiation by epoxide radical ring opening: Effect of solvents and additives

The effects of solvents, additives, ligands, and solvent in situ drying agents as well as catalyst and initiator concentrations have been investigated in the Cp₂TiCl‐catalyzed radical polymerization of styrene initiated by epoxide radical ring opening. On the basis of the solubilization of Cp₂Ti(III)Cl and the polydispersity of the resulting polymer, the solvents rank as follows: dioxane ≥ tetrahydrofuran > diethylene glycol dimethyl ether > methoxybenzene > diphenyl ether ≥ bulk > toluene ? pyridine > dimethylformamide > 1‐methyl‐2‐pyrrolidinone > dimethylacetamide > ethylene carbonate, acetonitrile, and trioxane. Alkoxide additives such as aluminum triisopropoxide and titanium(IV) isopropoxide are involved in alkoxide ligand exchange with the epoxide‐derived titanium alkoxide and lead to broad molecular weight distributions, whereas similarly to strongly coordinating solvents, ligands such as bipyridyl block the titanium active site and prevent the polymerization. By contrast, softer ligands such as triphenylphosphine improve the polymerization in less polar solvents such as toluene. Although mixed hydrides such as lithium tri‐tert‐butoxyaluminum hydride, sodium borohydride, and lithium aluminum hydride react with bis(cyclopentadienyl)titanium dichloride to form mixed titanium hydride species ineffective in polymerization control, simple hydrides such as lithium hydride, sodium hydride, and especially calcium hydride are particularly effective as in situ trace water scavengers in this polymerization. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2015–2026, 2006     

The ligand effect in Ti‐mediated living radical styrene polymerizations initiated by epoxide radical ring opening. 2. Scorpionate and half‐sandwich LTiCl3 complexes

The ligand effect and the reaction conditions for the living radical polymerization of styrene initiated by epoxide radical ring opening was investigated in a series of piano‐stool, Ti(IV) scorpionate and, half‐sandwich metallocenes (LTiCl₃; L = Tp, Cp*, Ind and Cp, where Tp = hydrotris(pyrazol‐1‐ylborato), Cp* = pentamethylcyclopentadienyl, Ind = indenyl and Cp = cyclopentadienyl). The polymerization is mediated by the reversible termination of the growing chains with Ti(III) species derived from Zn reduction of parent Ti(IV) derivatives. A poor performance was observed for TpTiCl₃ because of probable over‐reduction. The strong electron donating effect of Cp* accounts for a strong C? Ti chain end bond and consequently, a living‐like process is observed only at T > 110 °C. However, both Ind and Cp ligands provide a linear dependence of M_n on conversion and narrow polydispersity over a wide range of experimental conditions. Investigation of the effect of temperature and reagent ratios generates an optimum for epoxide/CpTiCl₃/Zn = 1/2/4 at 70–90 °C. On the basis of a combination of steric and electronic properties, the ligands rank as Cp ≥ Ind ? Cp* ? Tp. This trend is different from coordination polymerization, and in conjunction with our previous results on Cp₂TiCl₂, further supports a radical mechanism. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6039–6047, 2005     

The ligand effect in Ti‐mediated living radical styrene polymerizations initiated by epoxide radical ring opening. 1. Alkoxide and bisketonate Ti complexes

Bisketonate and alkoxide Ti(III) complexes derived from Zn reduction of Ti(IV) precursors were evaluated as catalysts for the living radical polymerization (LRP) of styrene initiated by Ti‐catalyzed epoxide radical ring opening and mediated by reversible termination with Ti(III). No polymerization occurred with tris(2,2,6, 6‐tetramethyl‐3,5‐heptanedionato)titanium (III), whereas dichlorobis(2,2,6,6‐tetramethyl‐3,5‐heptanedionato)titanium (IV) affords only a free radical polymerization. Preliminary living features were displayed by (ⁱPrO)₂TiCl₂. Investigations of the effect of epoxide/Ti/Zn ratios, temperature, and nature of the epoxide demonstrated that (ⁱPrO)₃TiCl provides a linear dependence of M_n on conversion over a wide range of conditions with an optimum for [Sty]/[epoxide group]/[Ti]/[Zn] = 50/1/2/4 at 90 °C. However, the polydispersity could not be reduced below 1.4–1.5, with an initiator efficiency of 0.15. These results were rationalized in terms of a combination of decreased Ti oxophilicity and ligand exchange. The lowered oxophilicity decreases the initiation rate and broadens M_w/M_n. The fast alkoxide exchange promotes a weak dependence of the polymerization on reaction conditions and generates macromolecular Ti species with reduced ability to mediate LRP. Thus, while monofunctional epoxides provide homogeneous polymerizations and narrower M_w/M_n, difunctional initiators may lead to gel formation at high conversion. Nonetheless, all polymerizations were light gray to colorless and afforded white polymer. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6028–6038, 2005     

Cp2TiCl‐catalyzed living radical polymerization of styrene initiated from peroxides

The effects of the reaction conditions and nature of the initiator were investigated in the Cp₂Ti(III)Cl‐catalyzed living radical polymerization of styrene initiated by benzoyl peroxide (BPO), tert‐butyl peroxide (TBPO), tert‐butyl peroxybenzoate (TBPOB), dicumyl peroxide (CPO), and tert‐butylperoxy 2‐ethylhexyl carbonate (TBPOEHC). The reversible termination of the growing chains with Cp₂Ti(III)Cl affords a linear dependence of molecular weight on conversion over a wide range of temperatures (60–120 °C) with an optimum in polydispersity (M_w/M_n < 1.2) for St/BPO/Cp₂TiCl₂/Zn = 100/1/3/6 at 60–90 °C. The similarity of the kinetic parameters from polymerizations initiated by peroxides with vastly different half‐life times (t = 1 h, t = 543 h) and the minimum peroxide/Ti = 1/2 ratio required for a living process indicate that initiation occurs primarily by the redox reaction of the peroxide with Cp₂Ti(III)Cl rather than peroxide thermal decomposition. This is consistent with one Ti equivalent consumed in the redox initiation and the second one utilized in the reversible termination of the growing chains. Qualitatively, based on the livingness of the process, these initiators ranked as BPO > TBPOB ～ TBPO > CPO > TBPOEHC. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1106–1116, 2006     

Living ring‐opening polymerization of ϵ‐caprolactone with Ti alkoxides derived from the Cp2TiCl‐catalyzed SET reduction of aldehydes

A series of substituted benzaldehydes were investigated as initiators for the living ring‐opening polymerization (LROP) of ε‐caprolactone (CL) mediated by titanium alkoxides obtained from the Cp₂TiCl‐catalyzed single electron transfer (SET) reduction of the carbonyl group following the in situ reduction of Cp₂TiCl₂ with Zn. The aldehyde initiation was demonstrated (NMR) by the presence of the initiator derived fragment on the polycaprolactone (PCL) chain end. The effect of the nature of the aldehyde functionality (R‐Ph‐CHO, R = H, Cl, PhCH₂O, NMe₂, CH₃O, NO₂, and CHO), reagent ratios ([CL]/[aldehyde] = 50/1 to 400/1, [aldehyde]/[Cp₂TiCl₂] = 1/1 to 1/4, and [Cp₂TiCl₂]/[Zn] = 1/0.5 to 1/2), and temperature (T = 75–120 °C) was investigated over a wide range of values to reveal a living polymerization in all cases with an optimum observed at 90 °C with typical stoichiometric ratios of [CL]/[aldehyde]/[Cp₂TiCl₂]/[Zn] = 100/1/1/2. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2869–2877, 2008     

Synthesis and characterization of well‐defined ABC‐type triblock copolymers via atom transfer radical polymerization and stable free‐radical polymerization

An asymmetric difunctional initiator 2‐phenyl‐2‐[(2,2,6,6 tetramethylpiperidino)oxy] ethyl 2‐bromo propanoate ( 1 ) was used for the synthesis of ABC‐type methyl methacrylate (MMA)‐tert‐butylacrylate (tBA)‐styrene (St) triblock copolymers via a combination of atom transfer radical polymerization (ATRP) and stable free‐radical polymerization (SFRP). The ATRP‐ATRP‐SFRP or SFRP‐ATRP‐ATRP route led to ABC‐type triblock copolymers with controlled molecular weight and moderate polydispersity (M_w/M_n < 1.35). The block copolymers were characterized by gel permeation chromatography and ¹H NMR. The retaining chain‐end functionality and the applying halide exchange afforded high blocking efficiency as well as maintained control over entire routes. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2025–2032, 2002     

Living/controlled radical copolymerization of N‐substituted maleimides with styrene in 1‐butyl‐3‐methylimidazolium hexafluorophosphate and anisole

The atom transfer radical copolymerization of N‐substituted maleimides such as N‐phenylmaleimide (PhMI), N‐cyclohexylmaleimide (ChMI), and N‐butylmaleimide (NBMI) with styrene initiated with dendritic polyarylether 2‐bromoisobutyrates in an ionic liquid, 1‐butyl‐3‐methylimidazolium hexafluorophosphate ([bmim][PF₆]), at room temperature and anisole at 110 °C was investigated. The dendritic‐linear block copolymers obtained in ionic liquid possessed well‐defined molecular weight and low polydispersity (1.05 < M_w/M_n < 1.32) and could be used as a macroinitiator for chain‐extension polymerization, suggesting the living nature of the reaction system. The ionic liquids containing catalyst could be recycled in the atom transfer radical polymerization systems without further treatment. Compared with polymerization conducted in anisole, the polymerization in ionic liquid had a stronger tendency for alternation. The tendency for alternation decreased in the order PhMI > NBMI > ChMI in [bmim][PF₆] and PhMI > ChMI > NBMI in anisole. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2156–2165, 2003     

A copper‐based reverse atom‐transfer radical polymerization process for the living radical polymerization of polyacrylonitrile

The reverse atom‐transfer radical polymerization (RATRP) technique using CuCl₂/2,2′‐bipyridine (bipy) complex as a catalyst was applied to the living radical polymerization of acrylonitrile (AN). A hexasubstituted ethane thermal iniferter, diethyl 2,3‐dicyano‐2,3‐diphenylsuccinate (DCDPS), was firstly used as the initiator in this copper‐based RATRP initiation system. A CuCl₂ to bipy ratio of 0.5 not only gives the best control of molecular weight and its distribution, but also provides rather rapid reaction rate. The rate of polymerization increases with increasing the polymerization temperature, and the apparent activation energy was calculated to be 57.4 kJ mol^?1. Because the polymers obtained were end‐functionalized by chlorine atoms, they were used as macroinitiators to proceed the chain extension polymerization in the presence of CuCl/bipy catalyst system via a conventional ATRP process. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 226–231, 2006     

Star polymers by cross‐linking of linear poly(benzyl‐L‐glutamate) macromonomers via free‐radical and RAFT polymerization. A simple route toward peptide‐stabilized nanoparticles

Poly(benzyl‐L ‐glutamate) (PBLG) macromonomers were synthesized by N‐carboxyanhydride (NCA) polymerization initiated with 4‐vinyl benzylamine. MALDI‐ToF analysis confirmed the presence of styrenic end‐groups in the PBLG. Free‐radical and RAFT polymerization of the macromonomer in the presence of divinyl benzene produced star polymers of various molecular weights, polydispersity, and yield depending on the reaction conditions applied. The highest molecular weight (M_w) of 10,170,000 g/mol was obtained in a free‐radical multibatch approach. It was shown that the PBLG star polymers can be deprotected to obtain poly(glutamic acid) star polymers, which form water soluble pH responsive nanoparticles. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis of polyacrylonitrile via reverse atom transfer radical polymerization catalyzed by FeCl3/isophthalic acid

FeCl₃ coordinated by isophthalic acid was first used as a catalyst in the azobisisobutyronitrile‐initiated reverse atom transfer radical polymerization of acrylonitrile. N,N‐Dimethylformamide was used as a solvent to improve the solubility of the ligand. An FeCl₃‐to‐isophthalic acid ratio of 0.5 not only gave the best control of the molecular weight and its distribution but also provided rather a rapid reaction rate. The effects of different solvents on the polymerization of acrylonitrile were also investigated. The rate of the polymerization in N,N‐dimethylformamide was faster than that in propylene carbonate and toluene. The molecular weight of polyacrylonitrile agreed reasonably well with the theoretical molecular weight in N,N‐dimethylformamide. The rate of polymerization increased with increasing polymerization temperature, and the apparent activation energy was calculated to be 59.9 kJ mol^?1. Reverse atom transfer radical polymerization was first used to successfully synthesize acrylonitrile polymers with a molecular weight higher than 80,000 and a narrow polydispersity as low as 1.22. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 219–225, 2006     

Similarities and differences of epoxide, aldehyde and peroxide initiators for Cp2TiCl-catalyzed styrene living radical polymerizations

Cp₂TiCl is the first example of a single electron transfer (SET) agent that both provides initiating radicals from three different types of functionalities (i.e. radical ring opening of epoxides and reduction of aldehydes and peroxides) and doubles as mediator for the living radical polymerization of styrene (St) by reversibly endcapping the growing polymer chains. An initiator (I) comparison was performed using 1,4-butanediol diglycidyl ether (BDE), benzaldehyde (BA) and benzoyl peroxide (BPO) as models. The investigation of the effect of reaction variables was carried out over a wide range of experimental conditions ([Cp₂TiCl₂]/[I] = 0.5/1-4/1; [Zn]/[Cp₂TiCl₂] = 0.5/1-3/1, [St]/[I] = 50/1-400/1 and T = 60-130 °C) to reveal living polymerization features such as a linear dependence of molecular weight on conversion and narrow molecular weight distribution (M_w/M_n) for each initiator class. However, progressively lower polydispersities and larger initiator efficiencies are obtained with increasing the [Cp₂TiCl₂]/[I] and [Zn]/[Cp₂TiCl₂] ratios and with decreasing temperature. Accordingly, optimum conditions correspond to [St]/[I]/[Cp₂TiCl₂]/[Zn] = [50-200]/[1]/[2-3]/[4-6] at 70-90 °C. By contrast to peroxides, aldehydes and the more reactive epoxides provide alcohol end groups useful in block or graft copolymers synthesis.     

Synthesis of poly(4‐vinylpyridine) by reverse atom transfer radical polymerization

Controlled radical polymerization of 4‐vinylpyridine (4VP) was achieved in a 50 vol % 1‐methyl‐2‐pyrrolidone/water solvent mixture using a 2,2′‐azobis(2,4‐dimethylpentanitrile) initiator and a CuCl₂/2,2′‐bipyridine catalyst–ligand complex, for an initial monomer concentration of [M]₀ = 2.32–3.24 M and a temperature range of 70–80 °C. Radical polymerization control was achieved at catalyst to initiator molar ratios in the range of 1.3:1 to 1.6:1. First‐order kinetics of the rate of polymerization (with respect to the monomer), linear increase of the number–average degree of polymerization with monomer conversion, and a polydispersity index in the range of 1.29–1.35 were indicative of controlled radical polymerization. The highest number–average degree of polymerization of 247 (number–average molecular weight = 26,000 g/mol) was achieved at a temperature of 70 °C, [M]₀ = 3.24 M and a catalyst to initiator molar ratio of 1.6:1. Over the temperature range studied (70–80 °C), the initiator efficiency increased from 50 to 64% whereas the apparent polymerization rate constant increased by about 60%. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5748–5758, 2007     

Copper(0)‐mediated living radical polymerization of acrylonitrile: SET‐LRP or AGET‐ATRP

Cu(0)‐mediated living radical polymerization was first extended to acrylonitrile (AN) to synthesize polyacrylonitrile with a high molecular weight and a low polydispersity index. This was achieved by using Cu(0)/hexamethylated tris(2‐aminoethyl)amine (Me₆‐TREN) as the catalyst, 2‐bromopropionitrile as the initiator, and dimethyl sulfoxide (DMSO) as the solvent. The reaction was performed under mild reaction conditions at ambient temperature and thus biradical termination reaction was low. The rapid and extensive disproportionation of Cu(I)Br/Me₆‐TREN in DMSO/AN supports a mechanism consistent with a single electron transfer‐living radical polymerization (SET‐LRP) rather than activators generated by electron transfer atom transfer radical polymerization (AGET ATRP). ¹H NMR analysis and chain extension experiment confirm the high chain‐end functionality of the resultant polymer. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

“Nascent” Cu(0) nanoparticles‐mediated single electron transfer living radical polymerization of acrylonitrile at ambient temperature

Zn(0)/ppm concentrations of CuBr₂ from 10 to 50 ppm was firstly used to catalyze radical polymerization of acrylonitrile at ambient temperature. The polymerization displayed typical living radical polymerization (LRP) characteristics, as evidenced by pseudo first‐order kinetics of polymerization, linear increase of number‐average molecular weight, and low polydispersity index (PDI) value. Effects of solvent, copper concentration, and initiator concentration on the polymerization reaction and molecular weight as well as PDI were investigated in detail. EC excelled NMP, DMF, and DMSO in terms of rate of polymerization as well as control of molecular weight and PDI. The increase of the copper concentration from 2.5 to 50 ppm leads to a higher rate of polymerization and a better control over the polymerization reaction. ¹H NMR and GPC analyses as well as chain extension reaction confirmed the very high chain‐end functionality of the resultant polymer. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Rapid ring‐opening polymerization of 1,4‐dioxan‐2‐one initiated by titanium alkoxides

Ring‐opening polymerization of 1,4‐dioxan‐2‐one in bulk was initiated by three titanium alkoxides, titanium dichlorodiisopropoxide (TiCl₂(OiPr)₂), titanium chlorotriisopropoxide (TiCl(OiPr)₃), and titanium tetraisopropoxide (Ti(OiPr)₄). The results indicate that the polymerization rate increased with number of OiPr groups in the initiator. High conversion of monomer (90%) and high molecular weight (11.9 × 10⁴ g/mol) of resulting polymer can be achieved in only 5 min at 60 °C with Ti(OiPr)₄ as an initiator. Analysis on nuclear magnetic resonance (NMR) spectra suggests the initiating sites for TiCl₂(OiPr)₂, TiCl(OiPr)₃, and Ti(OiPr)₄ to be 1.9, 2.6, and 3.8, respectively. Coordination‐insertion mechanism for the polymerization via cleavage of the acyl–oxygen bonds of the monomer was proved by NMR investigation. Kinetic studies indicate that polymerization initiated by Ti(OiPr)₄ followed a first‐order kinetics, with an apparent activation energy of 33.7 kJ/mol. It is noteworthy that this value is significantly lower than earlier reported values with other catalysts, namely La(OiPr)₃ (50.5 kJ/mol) and Sn(Oct)₂ (71.8 kJ/mol), which makes it an attractive catalyst for reactive extrusion polymerization. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Schiff base as a novel kind of catalyst for reversible complexation‐mediated radical polymerization of methyl methacrylate

Two kinds of Schiff base, N,N′‐dibenzylidene‐1,2‐diaminoethane (NDBE) and N,N′‐disalicylidene‐1,2‐diaminoethane, have been found as efficient organic catalyst for reversible complexation‐mediated radical polymerization (RCMP) of methyl methacrylate (MMA) for the first time. The polymerization results show obvious features of “living”/controlled radical polymerization. Well‐defined and low‐polydispersity polymers (M_w/M_n = 1.20–1.40) are obtained in RCMP of MMA catalyzed by Schiff base at mild temperature (65–80°C). Moreover, Schiff base also exhibits a particularly high reactivity for RCMP of MMA with in situ formed alkyl iodide initiator. The polymer molecular weight and its polydispersity (M_w/M_n is around 1.20) are well controlled even with high monomer conversion. Notably, when the dosage of azo initiator is same as the dosage of iodine, the polymerization could also be realized in the presence of NDBE. The living feature of synthesized polymer is confirmed through the chain extension experiment. In short, Schiff base is a kind of high‐efficient catalyst for RCMP and reverse RCMP of MMA, which can be one of the most powerful and robust techniques for polymer synthesis. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 1653–1663     

New ligands for the Fe(III)‐mediated reverse atom transfer radical polymerization of methyl methacrylate

A series of (di)picolinic acids and their derivates are investigated as novel complexing tridentate or bidentate ligands in the iron‐mediated reverse atom transfer radical polymerization of methyl methacrylate in N,N‐dimethylformamide at 100 °C with 2,2′‐azobisisobutyrontrile as an initiator. The polymerization rates and polydispersity indices (1.32–1.8) of the resulting polymers are dependent on the structures of the ligands employed. Different iron complexes may be involved in iron‐mediated reverse atom transfer radical polymerization, depending on the type of acid used. ¹H NMR spectroscopy has been used to study the structure of the resulting polymers. Chain‐extension reactions have been performed to further confirm the living nature of this catalytic system. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2912–2921, 2006     

9‐Bromoanthracene photodimers as initiators in controlled radical polymerization: Silane radical atom abstraction coupled with nitroxide mediated polymerization

Slow initiation relative to propagation has previously prevented photodimers of 9‐bromoanthracene or 9‐chloroanthracene, formed by [4 + 4] photocyclization reactions of the analogous 9‐haloanthracene, from being viable initiators in atom transfer radical polymerization (ATRP) reactions. The resulting polymers were found to possess high polydispersity index (PDI) values, much higher than expected number average molecular weight (M_n) values, with the reaction displaying a nonlinear relationship between monomer conversion and M_n. We report here the use of silane radical atom abstraction (SRAA) to create initiating bridgehead radicals in the presence of 2,2,6,6‐tetramethylpiperidine‐1‐oxyl (TEMPO) to mediate the polymerization. When using SRAA coupled with nitroxide mediated polymerization, a dramatic decrease in PDI values was observed compared with analogous ATRP reactions, with M_n values much closer to those anticipated based on monomer‐to‐initiator ratios. Analysis using UV‐Vis spectroscopy indicated only partial anthracene labeling (～ 25%) on the polymers, consistent with thermolysis of the anthracene photodimer coupled with competition between initiation from the bridgehead photodimer radical and silane‐based radical. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6016–6022, 2008     

Synthesis of well‐defined syndiotactic poly(methyl methacrylate) with low‐temperature atom transfer radical polymerization in fluoroalcohol

The copper‐mediated atom transfer radical polymerization of methyl methacrylate (MMA) in 1,1,1,3,3,3‐hexafluoro‐2‐propanol (HFIP) was studied to simultaneously control the molecular weight and tacticity. The polymerization using tris[2‐(dimethylamino)ethyl]amine (Me₆TREN) as a ligand was performed even at ?78°C with a number‐average molecular weight (M_n) of 13,400 and a polydispersity (weight‐average molecular weight/number‐average molecular weight) of 1.31, although the measured M_n's were much higher than the theoretical ones. The addition of copper(II) bromide (CuBr₂) apparently affected the early stage of the polymerization; that is, the polymerization could proceed in a controlled manner under the condition of [MMA]₀/[methyl α‐bromoisobutyrate]₀/[CuBr]₀/[CuBr₂]₀/[Me₆TREN]₀ = 200/1/1/0.2/1.2 at ?20°C with an MMA/HFIP ratio of 1/4 (v/v). For the field desorption mass spectrum of Cu^IBr/Me₆TREN in HFIP, there were [Cu(Me₆TREN)Br]⁺ and [Cu(Me₆TREN)OCH(CF₃)₂]⁺, indicating that HFIP should coordinate to the Cu^I/Me₆TREN complex. The syndiotacticity of the obtained poly(methyl methacrylate)s increased with the decreasing polymerization temperature; the racemo content was 84% for ?78°C, 77% for ?30°C, 75% for ?20°C, and 63% for 30°C. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1436–1446, 2006     

Living/controlled radical polymerization of styrene with a new initiating system: DCDPS/FeCl3/PPh3

The living/controlled radical polymerization of styrene was investigated with a new initiating system, DCDPS/FeCl₃/PPh₃, in which diethyl 2,3‐dicyano‐2,3‐diphenylsuccinate (DCDPS) was a hexa‐substituted ethane thermal iniferter. The polymerization mechanism belonged to a reverse atom transfer radical polymerization (ATRP) process. The polymerization was controlled closely in bulk (at 100 °C) or in solution (at 110 °C) with a high molecular weight and quite narrow polydispersity (M_w/M_n = 1.18 ∼ 1.28). End‐group analysis results by ¹H NMR spectroscopy showed that the polymer was ω‐functionalized by a chlorine atom, which also was confirmed by the result of a chain‐extension reaction in the presence of a FeCl₂/PPh₃ or CuCl/bipy (2,2′‐bipyridine) catalyst via a conventional ATRP process. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 101–107, 2000