Preparation and characterization of optically active polystyrene via a chiral nitroxide‐mediated polymerization

2,2,6,6‐Tetramethyl‐4‐[d‐(+)‐10‐camphorsulfonyl]‐1‐piperidinyloxy was synthesized and used as a chiral nitroxide for the bulk polymerizations of styrene initiated with benzoyl peroxide (BPO), tetraethylthiuram disulfide (TETD), and thermal initiation. The results showed that the polymerizations proceeded in a controlled/living way; that is, the kinetics presented approximately first‐order plots, and the number‐average molecular weights of the polymers with narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight) increased with the monomer conversion linearly. The molecular weight distributions in the case of thermal initiation were narrower than those in the case of BPO and TETD, whereas the polymerization rate with BPO or TETD as an initiator was obviously faster than that with thermal initiation. In addition, successful chain‐extension reactions were carried out, and the structures of the obtained polymers were characterized by gel permeation chromatography and ¹H NMR. The specific rotations of the polymers were also measured by polarimetric analysis. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1522–1528, 2006     

Living radical emulsion polymerization using the nanoprecipitation technique: An extension to atom transfer radical polymerization

Living radical polymerizations of styrene were performed under emulsion atom transfer radical polymerization conditions with latexes prepared by a nanoprecipitation technique recently developed for the stable free‐radical polymerization process. Latexes were prepared by the precipitation of a solution of low‐molecular‐weight polystyrene in acetone into a solution of a surfactant in water. The resulting particles were swollen with styrene and then heated. The effects of various surfactants and hydrophobic ligands, the reaction temperature, and the ligand/copper(I) bromide ratio were studied. The best results were obtained with the nonionic surfactant Brij 98 in combination with the hydrophobic ligand N,N‐bis(2‐pyridylmethyl)octadecylamine and a ligand/copper(I) bromide ratio of 1.5 at a reaction temperature of 85–90 °C. Under these conditions, latexes with good colloidal stability with average particle diameters of 200 nm were obtained. The molecular weight distributions of the polystyrenes were narrow, although the experimental molecular weights were slightly larger than the theoretical ones because not all the macroinitiator appeared to reinitiate. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4027–4038, 2006     

Atom transfer radical polymerization of sodium2‐acrylamido‐2‐methylpropanesulfonate

The first example of well‐controlled atom transfer radical polymerization (ATRP) of a permanently charged anionic acrylamide monomer is reported. ATRP of sodium 2‐acrylamido‐2‐methylpropanesulfonate (NaAMPS) was achieved with ethyl 2‐chloropropionate (ECP) as an initiator and the CuCl/CuCl₂/tris(2‐dimethylaminoethyl)amine (Me₆TREN) catalytic system. The polymerizations were carried out in 50:50 (v/v) N,N‐dimethylformamide (DMF)/water mixtures at 20 °C. Linear first‐order kinetic plots up to a 92% conversion for a target degree of polymerization of 50 were obtained with [ECP]/[CuCl]/[CuCl₂]/[Me₆TREN] = 1:1:1:2 and [AMPS] = 1 M. The molecular weight increased linearly with the conversion in good agreement with the theoretical values, and the polydispersities decreased with increasing conversion, reaching a lower limit of 1.11. The living character of the polymerization was confirmed by chain‐extension experiments. Block copolymers with N,N‐dimethylacrylamide and N‐isopropylacrylamide were also prepared. The use of a DMF/water mixed solvent should make possible the synthesis of new amphiphilic ionic block copolymers without the use of protecting group chemistry. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4446–4454, 2005     

Emulsion atom transfer radical block copolymerization of 2‐ethylhexyl methacrylate and methyl methacrylate

The emulsion atom transfer radical block copolymerization of 2‐ethylhexyl methacrylate (EHMA) and methyl methacrylate (MMA) was carried out with the bifunctional initiator 1,4‐butylene glycol di(2‐bromoisobutyrate). The system was mediated by copper bromide/4,4′‐dinonyl‐2,2′‐bipyridyl and stabilized by polyoxyethylene sorbitan monooleate. The effects of the initiator concentration and temperature profile on the polymerization kinetics and latex stability were systematically examined. Both EHMA homopolymerization and successive copolymerization with MMA proceeded in a living manner and gave good control over the polymer molecular weights. The polymer molecular weights increased linearly with the monomer conversion with polydispersities lower than 1.2. A low‐temperature prepolymerization step was found to be helpful in stabilizing the latex systems, whereas further polymerization at an elevated temperature ensured high conversion rates. The EHMA polymers were effective as macroinitiators for initiating the block polymerization of MMA. Triblock poly(methyl methacrylate–2‐ethylhexyl methacrylate–methyl methacrylate) samples with various block lengths were synthesized. The MMA and EHMA reactivity ratios determined by a nonlinear least‐square method were ～0.903 and ～0.930, respectively, at 70 °C. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1914–1925, 2006     

Synthesis of diblock copolymers by combining stable free radical polymerization and atom transfer radical polymerization

A stable nitroxyl radical functionalized with an initiating group for atom transfer radical polymerization (ATRP), 4‐(2‐bromo‐2‐methylpropionyloxy)‐2,2,6,6‐tetramethyl‐1‐piperidinyloxy (Br‐TEMPO), was synthesized by the reaction of 4‐hydroxyl‐2,2,6,6‐tetramethyl‐1‐piperidinyloxy with 2‐bromo‐2‐methylpropionyl bromide. Stable free radical polymerization of styrene was then carried out using a conventional thermal initiator, dibenzoyl peroxide, along with Br‐TEMPO. The obtained polystyrene had an active bromine atom for ATRP at the ω‐end of the chain and was used as the macroinitiator for ATRP of methyl acrylate and ethyl acrylate to prepare block copolymers. The molecular weights of the resulting block copolymers at different monomer conversions shifted to higher molecular weights and increased with monomer conversion. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2468–2475, 2006     

Reversible‐addition fragmentation chain transfer radical emulsion polymerization by a nanoprecipitation process

Polymerizations of styrene under emulsion reversible‐addition fragmentation chain transfer polymerization conditions are reported. Using a recently developed nanoprecipitaiton process, emulsion particles were formed by the precipitation of an acetone solution of a macroRAFT agent into an aqueous solution of poly(vinyl alcohol). The particles were then swollen with monomer and subsequently polymerized. Emulsion polymerizations were performed at 65 and 75 °C in which either KPS, BPO, or a combination of both was used as an initiating source. Reactions were also performed at temperatures over 100 °C in which the thermal initiation of styrene was used as an initiating source. In all cases, the polymerizations proceeded in a living manner, yielding polymers that showed an incremental increase in molecular weight with time and had narrow molecular weight distributions. Plots of number‐ average molecular weight versus conversion were linear, indicating a controlled polymerization. The resulting latices were colloidally stable and gave particle size distributions with a typical average particle diameter in the 150 nm range. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5708–5718, 2006     

New antibacterial cationic surfactants prepared by atom transfer radical polymerization

Efficient antibacterial surfactants have been prepared by the quaternization of the amino groups of poly(ethylene‐co‐butylene)‐b‐poly[2‐(dimethylamino)ethylmethacrylate] (PEB‐b‐PDMAEMA) diblock copolymers by octyl bromide. The diblock copolymers have been synthesized by ATRP of 2‐(dimethylamino)ethylmethacrylate (DMAEMA) initiated by an activated bromide‐end‐capped poly(ethylene‐co‐butylene). In the presence of CuBr, 1,4,7,10,10‐hexamethyl‐triethylenetetramine (HMTETA), and toluene at 50 °C, the initiation is slow in comparison with propagation. This situation has been improved by the substitution of CuCl for CuBr, all the other conditions being the same. Finally, the addition of an excess of CuCl₂ (deactivator) to the CuCl/HMTETA catalyst is very beneficial in making the agreement between the theoretical and experimental number‐average molecular weights excellent. The antibacterial activity of PEB‐b‐PDMAEMA quaternized by octyl bromide has been assessed against bacteria and is comparable to the activity of a commonly used disinfectant, that is, benzalkonium chloride. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1214‐1224, 2006     

A novel rate‐accelerating additive for atom transfer radical polymerization of styrene

The polymerization of styrene was mediated by copper (I) bromide/pentramethldiethyltriamine (PMDETA) using ethyl 2‐bromopropionate (EBP) as initiator and a catalytic amount of malononitrile (MN) as a novel rate‐accelerating additive. The optimal molar ratios of MN/EBP under which the polymerization of styrene can proceed fastest was 4:1. The rate‐enhancement‐efficiency had a dependence on temperature and the apparent rate constant of polymerization improved by a factor of 2.67 at 85 °C. Polymerization resulted in a conversion as high as 87% in 4.3 h in the presence of MN, while a conversion of 79.7% was gained even in 10 h without MN at 85 °C. The polymerizations of styrene in the presence of MN proceeded in a living fashion indicated by the first‐order kinetic plots, with the increase of M_n with respect to conversion and the relatively narrow polydispersity. The possible rate enhancing mechanism is that the addition of MN weakens the coordination between the copper center and ligand and facilitates the atom transfer process. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4082–4090, 2007     

The synthesis of poly[6,8‐dioxabicyclo[3.2.1]octane‐b‐(ethylene glycol)‐b‐6,8‐dioxabicyclo[3.2.1]octane] by controlled cationic ring‐opening polymerization

The triblock copolymer poly[6,8‐dioxabicyclo[3.2.1]octane‐b‐(ethylene glycol)‐b‐6,8‐dioxabicyclo[3.2.1]octane] was prepared by the controlled cationic ring‐opening polymerization of 6,8‐dioxabicyclo[3.2.1]octane (6,8‐DBO) from a macroinitiator. The macroinitiator, poly(ethylene glycol) (PEG) di(1‐chloroethyl ether), was prepared via the addition of HCl to PEG divinyl ether and was characterized with ¹³C NMR, ¹H NMR, and gel permeation chromatography (GPC). Upon preparation, a small fraction of the chain ends underwent a cyclization reaction to form inactive chain ends. When the macroinitiator was used in polymerizations of 6,8‐DBO with ZnI₂ as an activator, linear kinetic plots were observed, a linear increase in the copolymer molecular weight with conversion was seen, and the molecular weight distributions of the copolymer samples remained constant at about 1.40. Confirmation of the triblock structure of the final product was obtained with ¹H NMR spectra, ¹³C DEPT spectra, and GPC chromatograms. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4081–4087, 2000     

Eutectic mixtures as a green alternative for efficient catalyst recycling in atom transfer radical polymerizations

A new solvent mixture, based on ethanol/reline (EM: eutectic mixture), was investigated for the supplemental activator and reducing agent atom transfer radical polymerization (SARA ATRP) of methyl acrylate (MA) near room temperature, for the first time, affording complete catalyst recovery and reuse. The kinetic results revealed that the polymerizations were controlled, with polymers having narrow molecular weight distributions (? < 1.2). The “living” character of the resultant PMA was confirmed by the synthesis of a well‐defined PMA‐b‐PBA block copolymer. Remarkably, it was demonstrated that the Cu(0)/CuBr₂/Me₆TREN (Me₆TREN: tris[2‐(dimethylamino)ethyl]amine) could be recovered from the final reaction mixture and reused for new successful SARA ATRP of MA, suggesting that the reported system could be very attractive from both the economic and environmental perspectives. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 371–381     

Synthesis of linear and starlike polymers from poly(propylene glycol) methacrylate using controlled radical polymerization

The copper‐catalyzed atom transfer radical polymerization (ATRP) of poly(propylene glycol) methacrylate (PPGM) in solution to produce linear and starlike polymers is reported, using methylethyl ketone as the solvent and a temperature of 80 °C. The ATRP system used was efficient for polymerization of the functionalized monomer without protecting hydroxyl end groups of monomer. The polymerizations were consistent with “living” or controlled processes, as revealed by the linear evolution of molecular weight with conversion. Increasing the [M]₀:[I]₀ ratio resulted in increasing molecular weights, whereas the polydispersity indices remained low (M_w/M_n < 1.4) even at high conversion. Decreasing the [CuBr]₀:[I]₀ ratio resulted in lower conversions, slightly larger polydispersities, and decreased molecular weights, likely resulting from a lower initiation efficiency. Polymers were characterized by ¹H and ¹³C NMR; molecular weights of polymers with low degrees of polymerization were estimated by end‐group analysis from ¹³C NMR spectra obtained using distortionless enhancement by polarization transfer and the gated decoupling techniques. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 334–343, 2002     

Phosphorus ligands for iron(III)‐mediated ATRP of styrene via generation of activators by monomer addition

Styrene polymerization via generation of activators by monomer addition (GAMA) for atom transfer radical polymerization (ATRP) has been examined extensively with bulk FeX₃ and FeX₂ at 110 °C in conjunction with various phosphorus‐bearing ligands. It was found that GAMA possesses advantages over normal ATRP. Most importantly, narrower polydispersity index (PDI) values were observed from the styrene polymerizations with Fe(III) over those with Fe(II). Every instance of 2‐(diphenylphosphino)‐N,N′‐dimethyl‐[1,1′‐biphenyl]‐2‐amine and 2‐(diphenylphosphino) pyridine with the Fe(III) system were controlled excellently without addition of any radical initiator or reducing agent additives. Initiator type was found to exert a significant factor to influence on the controllability of polymerization. The initiation of 1‐phenylethyl chloride and methyl‐2‐chloropropionate gave rise to formation of polymers with narrow PDI (1.05–1.20), whereas those from 1‐phenylethyl bromide increased to 1.35. The GAMA of bulk styrene exhibited the best performance in terms of both rate and controllability compared with toluene and anisole. Both formation of block copolymer from the macroinitiator and efficient perturbation of polymerization with 2,2,6,6‐tetramethylpiperidine 1‐oxyl provided firm evidence to support the living and radical characteristics for the GAMA of styrene. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 144–151, 2010     

2‐[(Diphenylphosphino)methyl]pyridine as ligand for iron‐based atom transfer radical polymerization

2‐[(Diphenylphosphino)methyl]pyridine (DPPMP) was successfully used as a bidentate ligand in the iron‐mediated atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) with various initiators and solvents. The effect of the catalytic system on ATRP was studied systematically. Most of the polymerizations with DPPMP ligand were well controlled with a linear increase in the number‐average molecular weights (M_n) versus conversion and relatively low molecular weight distributions (M_w/M_n = 1.10–1.3) being observed throughout the reactions, and the measured molecular weights matched the predicted values. Initially added iron(III) bromide improved the controllability of the polymerization reactions in terms of molecular weight control. The ratio of ligand to metal influenced the controllability of ATRP system, and the optimum ratio was found to be 2:1. It was shown that ATRP of MMA with FeX₂/DPPMP catalytic system (X = Cl, Br) initiated by 2‐bromopropionitrile (BPN) was controlled more effectively in toluene than in polar solvents. The rate of polymerization increased with increasing the polymerization temperature and the apparent activation energy was calculated to be 56.7 KJ mol^?1. In addition, reverse ATRP of MMA was able to be successfully carried out using AIBN in toluene at 80 °C. Polymerization of styrene (St) was found to be controlled well by using the PEBr/FeBr₂/DPPMP system in DMF at 110 °C. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2922–2935, 2008     

Outer‐sphere electron transfer metal‐catalyzed polymerization of styrene using a macrobicyclic ligand

The CuBr‐catalyzed polymerizations of styrene in the presence of a macrobicyclic mixed donor (N and S) encapsulating ligand, NH₂capten, were carried out in toluene at 60 and 100 °C. The macrobicyclic nature of the ligand ensures that a transition metal ion is effectively encapsulated (caged) within the three‐dimensional cavity, resulting in activation of radicals through an outer‐sphere electron transfer mechanism. The kinetic data showed that the polymerizations were uncontrolled with little “living” behavior. The external orders of reaction in [CuBr], [NH₂capten], and [CuBr₂] were 0.5, 0.5, and close to zero, respectively, in agreement with the postulated mechanism of little or no deactivation of polymeric radicals and a significant amount of bimolecular termination. Although “living” behavior was not found using the cage ligand, it was decided that it would provide an ideal method for radical coupling experiments to make high‐molecular weight multiblock copolymers from a difunctional PSTY (Br‐PSTY‐Br, PDI = 1.11). The coupling reaction of Br‐PSTY‐Br using CuBr/NH₂capten and excess Cu(0) in toluene at 100 °C gave no loss of the starting Br‐PSTY‐Br. Changing the solvent to the aprotic DMSO resulted in a significant increase in the rate of consumption of starting Br‐PSTY‐Br, with over 87% being used in under 10 min at 60 °C. In addition, higher molecular weight species were also formed, suggesting that OSET gives little or no side reactions on this time scale. It was initially thought that to get such high rates of reaction that the SET‐LRP disproportionation mechanism (2Cu(I) → Cu(0) + Cu(II)) was at play. However, UV–Vis experiments of the CuBr/NH₂capten showed little or no disproportionation products. This important result suggests that DMSO catalyzes the OSET reaction through the stabilization of the radical‐anion intermediate, which then rapidly fragments to a polymeric radical. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 146–154, 2008     

Reversible addition–fragmentation chain transfer polymerization of glycidyl methacrylate with 2‐cyanoprop‐2‐yl 1‐dithionaphthalate as a chain‐transfer agent

A reversible addition–fragmentation chain transfer (RAFT) agent, 2‐cyanoprop‐2‐yl 1‐dithionaphthalate (CPDN), was synthesized and applied to the RAFT polymerization of glycidyl methacrylate (GMA). The polymerization was conducted both in bulk and in a solvent with 2,2′‐azobisisobutyronitrile (AIBN) as the initiator at various temperatures. The results for both types of polymerizations showed that GMA could be polymerized in a controlled way by RAFT polymerization with CPDN as a RAFT agent; the polymerization rate was first‐order with respect to the monomer concentration, and the molecular weight increased linearly with the monomer conversion up to 96.7% at 60 °C, up to 98.9% at 80 °C in bulk, and up to 64.3% at 60 °C in a benzene solution. The polymerization rate of GMA in bulk was obviously faster than that in a benzene solution. The molecular weights obtained from gel permeation chromatography were close to the theoretical values, and the polydispersities of the polymer were relatively low up to high conversions in all cases. It was confirmed by a chain‐extension reaction that the AIBN‐initiated polymerizations of GMA with CPDN as a RAFT agent were well controlled and were consistent with the RAFT mechanism. The epoxy group remained intact in the polymers after the RAFT polymerization of GMA, as indicated by the ¹H NMR spectrum. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2558–2565, 2004     

Facile synthesis of AB2‐type miktoarm star polymers through the combination of atom transfer radical polymerization and ring‐opening polymerization

A novel miktofunctional initiator ( 1 ), 2‐hydroxyethyl 3‐[(2‐bromopropanoyl)oxy]‐2‐{[(2‐bromopropanoyl)oxy]methyl}‐2‐methyl‐propanoate, possessing one initiating site for ring‐opening polymerization (ROP) and two initiating sites for atom transfer radical polymerization (ATRP), was synthesized in a three‐step reaction sequence. This initiator was first used in the ROP of ?‐caprolactone, and this led to a corresponding polymer with secondary bromide end groups. The obtained poly(?‐caprolactone) (PCL) was then used as a macroinitiator for the ATRP of tert‐butyl acrylate or methyl methacrylate, and this resulted in AB₂‐type PCL–[poly(tert‐butyl acrylate)]₂ or PCL–[poly(methyl methacrylate)]₂ miktoarm star polymers with controlled molecular weights and low polydispersities (weight‐average molecular weight/number‐average molecular weight < 1.23) via the ROP–ATRP sequence. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2313–2320, 2004     

Acid dissolution of copper oxides as a method for the activation of Cu(0) wire catalyst for SET‐LRP

Here we reported the acid dissolution of copper oxides as a methodology for the activation of Cu(0) wire used as catalyst in single‐electron transfer living radical polymerization (SET‐LRP). In this method, the oxide layer on the surface of commercial Cu(0) wire was removed by dissolution in a concentrated acid such as nitric acid, glacial acetic acid and hydrochloric acid. SET‐LRP of methyl acrylate catalyzed with Cu(0) wire activated with acids showed comparable k value to that of the nonactivated Cu(0) wire‐catalyzed counterpart. However, the polymerizations catalyzed with activated Cu(0) wire proceeded with no initial induction period, predictable molecular weight evolution with conversion, and narrow molecular weight distribution. Regardless of the activation method, the chain end functionality of α,ω‐di(bromo) poly(methyl acrylate) (PMA) prepared from SET‐LRP initiated with a bifunctional initiator is extremely high, maintaining a 100% chain end functionality at ～90% monomer conversion. The degree of bimolecular termination increased as the polymerization exceeds 92% conversion. However, for binfunctional initiators this small amount of bimolecular termination at high conversion maintains a perfectly bifunctional polymer. Structural analysis by MALDI‐TOF upon thioetherification of α,ω‐di(bromo) PMA with thiophenol and 4‐fluorothiophenol confirmed the high fidelity of bromide chain ends. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

SET‐LRP of methyl acrylate to complete conversion with zero termination

The single electron transfer‐living radical polymerization of methyl acrylate (MA) initiated by bis(2‐bromopropionyl)ethane (BPE) in dimethyl sulfoxide was carried out to 100% monomer conversion and complete absence of bimolecular termination under the following reaction conditions: [MA]/[BPE]/[Me₆‐TREN]/[CuBr₂] = 60/1/0.21/0.01 and [MA]/[BPE]/[TREN]/[CuBr₂] = 60/1/0.25/0.05. These polymerizations were mediated by 0.5 cm of hydrazine‐activated Cu(0) wire of 20 gauge (0.812 cm in diameter), corresponding to a surface area of 0.14 cm² of Cu(0) per 3 mL reaction volume (2/1 v/v monomer/solvent). A higher extent of bimolecular termination (5–13%) was observed at complete conversion when longer lengths of Cu(0) wire were used. In the absence of CuBr₂ the activated Cu(0) wire/Me₆‐TREN catalyst in dimethyl sulfoxide also allowed the synthesis of perfectly bifunctional and monofunctional PMAs at complete conversion. This was also demonstrated by the quantitative reinitiation experiments from the chain(s) end(s) of these macroinitiators. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Reversible addition–fragmentation chain transfer polymerization of styrene under microwave irradiation

Reversible addition–fragmentation chain transfer (RAFT) polymerizations of styrene under microwave irradiation (MI), with or without azobisisobutyronitrile, were successfully carried out in bulk at 72 and 98 °C, respectively. The results showed that the polymerizations had living/controlled features, and there was a significant enhancement of the polymerization rates under MI in comparison with conventional heating (CH) under the same conditions. The polymer structures were characterized with ¹H and ¹³C NMR. The results showed the same structure for both polymers obtained by MI and CH. Successful chain‐extension experimentation further demonstrated the livingness of the RAFT polymerization carried out under MI. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6810‐6816, 2006     

Synthesis of amphiphilic copolymer brushes: Poly(ethylene oxide)‐graft‐polystyrene

A well‐defined amphiphilic copolymer brush with poly(ethylene oxide) as the main chain and polystyrene as the side chain was successfully prepared by a combination of anionic polymerization and atom transfer radical polymerization (ATRP). The glycidol was first protected by ethyl vinyl ether to form 2,3‐epoxypropyl‐1‐ethoxyethyl ether and then copolymerized with ethylene oxide by the initiation of a mixture of diphenylmethylpotassium and triethylene glycol to give the well‐defined polymer poly(ethylene oxide‐co‐2,3‐epoxypropyl‐1‐ethoxyethyl ether); the latter was hydrolyzed under acidic conditions, and then the recovered copolymer of ethylene oxide and glycidol {poly(ethylene oxide‐co‐glycidol) [poly(EO‐co‐Gly)]} with multiple pending hydroxymethyl groups was esterified with 2‐bromoisobutyryl bromide to produce the macro‐ATRP initiator [poly(EO‐co‐Gly)_(ATRP). The latter was used to initiate the polymerization of styrene to form the amphiphilic copolymer brushes. The object products and intermediates were characterized with ¹H NMR, matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry, Fourier transform infrared, and size exclusion chromatography in detail. In all cases, the molecular weight distribution of the copolymer brushes was rather narrow (weight‐average molecular weight/number‐average molecular weight < 1.2), and the linear dependence of ln[M₀]/[M] (where [M₀] is the initial monomer concentration and [M] is the monomer concentration at a certain time) on time demonstrated that the styrene polymerization was well controlled. This method has universal significance for the preparation of copolymer brushes with hydrophilic poly(ethylene oxide) as the main chain. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4361–4371, 2006