Quinone transfer radical polymerization (QTRP) of styrene: Catalysis by different metal complexes

Styrene has been polymerized by a Quinone Transfer Radical Polymerization (QTRP) based on the redox reaction of an ortho‐quinone and a metal catalyst. Several metal acetylacetonates have been tested in this work. The radical polymerization of styrene is largely controlled when phenanthrenequinone (PhQ) is used with catalytic amounts of Co(acac)₂, Ni(acac)₂, Mn(acac)_{2 or 3}, and Al(acac)₃. As a rule, in the presence of all these metallic complexes, the polystyrene molar mass increases with the monomer conversion, and polydispersity (M_w/M_n) is in the 1.3–1.6 range (at least until 40% monomer conversion). Styrene polymerization has also been resumed by polystyrene chains prepared by QTRP. In the specific case of manganese acetylacetonates, an amine or phosphine ligand has to be added for the control to be effective. Finally, two mechanistic hypotheses have been proposed, depending on whether the oxidation state of the metal can be easily changed or not. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2723‐2733, 2005     

Controlled radical polymerization of styrene mediated by the C‐phenyl‐N‐tert‐butylnitrone/AIBN pair: Kinetics and electron spin resonance analysis

Kinetics of the free radical polymerization of styrene at 110 °C has been investigated in the presence of C‐phenyl‐N‐tert‐butylnitrone (PBN) and 2,2′‐azobis(isobutyronitrile) (AIBN) after prereaction in toluene at 85 °C. The effect of the prereaction time and the PBN/AIBN molar ratio on the in situ formation of nitroxides and alkoxyamines (at 85 °C), and ultimately on the control of the styrene polymerization at 110 °C, has been investigated. As a rule, the styrene radical polymerization is controlled, and the mechanism is one of the classical nitroxide‐mediated polymerization. Only one type of nitroxide (low‐molecular‐mass nitroxide) is formed whatever the prereaction conditions at 85 °C, and the equilibrium constant (K) between active and dormant species is 8.7 × 10^?10 mol L^?1 at 110 °C. At this temperature, the dissociation rate constant (k_d) is 3.7 × 10^?3 s^?1, the recombination rate constant (k_c) is 4.3 × 10⁶ L mol^?1 s^?1, whereas the activation energy (E_a,diss.), for the dissociation of the alkoxyamine at the chain‐end is ～125 kJ mol^?1. Importantly, the propagation rate at 110 °C, which does not change significantly with the prereaction time and the PBN/AIBN molar ratio at 85 °C, is higher than that for the thermal polymerization at 110 °C. This propagation rate directly depends on the equilibrium constant K and on the alkoxyamine and nitroxide concentrations, as well. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1219–1235, 2007     

Abilities of 1‐(9‐anthrylmethyloxy)‐2‐pyridone and related compounds to initiate radical and cationic photopolymerizations

This study explored the abilities of 1‐(9‐anthrylmethyloxy)‐2‐pyridone and related compounds, which absorb long‐wavelength light (>350 nm), to photochemically initiate radical and cationic polymerizations. It was found that the irradiation of the title compounds initiates the radical polymerization of styrene whereas the cationic polymerization of oxetane proceeds in the presence of these photoinitiators to a negligible extent. The behavior of 9‐anthrylmethyloxyl and amidyl radicals in the photopolymerization process of styrene was discussed based on ¹H NMR, UV, and fluorescence spectral data. In addition, the photoinitiation ability of the anthrylmethyloxyl end group was also investigated by using its model compound. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2859–2865, 2004     

Investigations of thermal polymerization in the stable free‐radical polymerization of 2‐vinylnaphthalene

The feasibility of utilizing stable free‐radical polymerization (SFRP) in the synthesis of well‐defined poly(2‐vinylnaphthalene) homopolymers has been investigated. Efforts to control molecular weight by manipulating initiator concentration while maintaining a 2,2,6,6‐tetramethylpiperidinyl‐1‐oxy (TEMPO):benzoyl peroxide (BPO) molar ratio of 1.2:1 proved unsuccessful. In addition, systematic variations of the TEMPO: BPO molar ratio did not result in narrow molecular weight distributions. In situ Fourier transform infrared spectroscopy (FTIR) indicated that the rate of monomer disappearance under SFRP and thermal conditions were identical. This observation indicated a lack of control in the presence of the stable free radical, TEMPO. The similarities in chemical structure between styrene and 2‐vinylnaphthalene suggested thermally initiated polymerization occurred via the Mayo mechanism. A kinetic analysis of the thermal polymerization of styrene and 2‐vinylnaphthalene suggested that the additional fused ring in 2‐vinylnaphthalene increased the propensity for thermal polymerization. The observed rate constant for thermal polymerization of 2‐vinylnaphthalene was determined using in situ FTIR spectroscopy and was one order of magnitude greater than styrene, assuming pseudo‐first‐order kinetics. Also, an Arrhenius analysis indicated that the activation energy for the thermal polymerization of 2‐vinylnaphthalene was 30 kJ/mol less than styrene. © 2002 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 583–590, 2002; DOI 10.1002/pola.10131     

Hydrogen‐bonding characteristics and unique ring‐opening polymerization behavior of Ortho‐methylol functional benzoxazine

Monofunctional benzoxazine with ortho‐methylol functionality has been synthesized and highly purified. The chemical structure of the synthesized monomer has been confirmed by ¹H and ¹³C nuclear magnetic resonance spectroscopy (NMR), Fourier transform infrared spectroscopy (FT‐IR) and elemental analysis. One‐dimensional (1D) ¹H NMR is used with respect to varied concentration of benzoxazines to study the specific nature of hydrogen bonding in both ortho‐methylol functional benzoxazine and its para counterpart. The polymerization behavior of benzoxazine monomer has been also studied by in situ FT‐IR and differential scanning calorimetry, experimentally supporting the polymerization mechanism of ortho‐methylol functional benzoxazine we proposed before. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3635–3642     

1,3‐dichlorotetra‐n‐butyldistannoxane as a novel ATRP initiator: Property,catalysis ability,and mechanism

1,3‐dichloro‐tetra‐n‐butyl‐distannoxane, which contains Sn? Cl bonds, was used as a novel initiator for atom transfer radical polymerization of styrene in bulk. Some interesting results that were thought to be related to the characteristics of the 1,3‐dihalotetra‐alkyl‐distannoxanes had been obtained. The concentration of the 1,3‐dichlorotetra‐n‐butyl‐distannoxane in the bulk solution of styrene was confirmed to be an important factor for the different results of the polymerization. The corrected theoretical molecular weights, which were based on the proposed mechanism, accorded with the GPC results very well. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 942–948, 2007     

Acrylonitrile‐containing polymers via a combination of metal‐catalyzed living radical and nitroxide‐mediated free‐radical polymerization routes

2‐Phenyl‐2‐[(2,2,6,6‐tetramethylpiperidino)oxy] ethyl 2‐bromopropanoate was successfully used as an initiator in consecutive living radical polymerization routes, such as metal‐catalyzed living radical polymerization and nitroxide‐mediated free‐radical polymerization, to produce various types of acrylonitrile‐containing polymers, such as styrene–acrylonitrile, polystyrene‐b‐styrene–acrylonitrile, polystyrene‐b‐poly(n‐butyl acrylate)‐b‐polyacrylonitrile, and polystyrene‐b‐polyacrylonitrile. The kinetic data were obtained for the metal‐catalyzed living radical polymerization of styrene–acrylonitrile. All the obtained polymers were characterized with ¹H NMR, gel permeation chromatography, and differential scanning calorimetry. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3374–3381, 2006     

Anionic polymerization of o‐substituted styrene derivatives: Control of reactivity and stereochemistry by aminomethyl group

Ortho‐substituted styrenes, such as 2‐(N,N‐dimethylaminomethyl)styrene ( 1 ), 2‐(1‐pyrrolidinylmethyl)styrene ( 2 ), and 2‐[(S)‐2‐(1‐pyrrolidinylmethyl)‐1‐pyrrolidinylmethyl]styrene ( 3 ), were synthesized, and the effects of the ortho‐substituents on the polymerizability and stereoregularity of the obtained polymers using the anionic method were examined. The bulkiness and coordination of the ortho‐substituted amino groups to the counter cation significantly affected the polymerizability and stereochemistry of the obtained polymers. The anionic and radical polymerizations of 2 with a less hindered ortho‐substituent afforded polymers in good yields, whereas those of 1 and 3 resulted in lower yields. The anionic polymerization of 3 bearing an optically active diamine derivative at the ortho‐position with n‐butyllithium in toluene at 0 °C gave a polymer with a high stereoregularity and stable regular conformation based on the stereoregular backbone structure. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4088–4094, 2000     

Kinetic analysis of styrene atom transfer radical polymerization: Extraction of radical‐radical termination rate coefficients

Kinetic studies of the atom transfer radical polymerization (ATRP) of styrene are reported, with the particular aim of determining radical‐radical termination rate coefficients (<k_t>). The reactions are analyzed using the persistent radical effect (PRE) model. Using this model, average radical‐radical termination rate coefficients are evaluated. Under appropriate ATRP catalyst concentrations, <k_t> values of approximately 2 × 10⁸ L mol^?1 s^?1 at 110 °C in 50 vol % anisole were determined. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5548–5558, 2004     

Relevance of a prereaction for the in situ NMP of styrene using the C‐Phenyl‐N‐tert‐butylnitrone/2,2′‐azobis(isobutyronitrile) pair

In this article, we compare two routes for carrying out in situ nitroxide‐mediated polymerization of styrene using the C‐phenyl‐N‐tert‐butylnitrone (PBN)/2,2′‐azobis(isobutyronitrile) (AIBN) pair to identify the best one for an optimal control. One route consists in adding PBN to the radical polymerization of styrene, while the other approach deals with a prereaction between the nitrone and the free radical initiator prior to the addition of the monomer and the polymerization. The combination of ESR and kinetics studies allowed demonstrating that when the polymerization of styrene is initiated by AIBN in the presence of enough PBN at 110 °C, fast decomposition of AIBN is responsible for the accumulation of dead polymer chains at the early stages of the polymerization, in combination with controlled polystyrene chains. On the other hand, PBN acts as a terminating agent at 70 °C with the formation of a polystyrene end‐capped by an alkoxyamine, which is not labile at this temperature but that can be reactivated and chain‐extended by increasing the temperature. Finally, the radical polymerization of styrene is better controlled when the nitrone/initiator pair is prereacted at 85 °C for 4 h in toluene before styrene is added and polymerized at 110 °C. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1085–1097, 2009     

Cyclometalated 2‐phenylpyridine complex [RuII(o‐C6H4‐py)(MeCN)4]PF6 as a tunable catalyst for living radical polymerization

The cyclometalated complex [Ru^II(o‐C₆H₄‐py)(MeCN)₄]PF₆ ( 1 ) with a σ‐Ru? C bond and four substitutionally labile acetonitrile ligands mediates radical polymerization of different vinyl monomers, viz. n‐butyl acrylate, methyl methacrylate, and styrene, initiated by three alkyl bromides: ethyl 2‐bromoisobutyrate, methyl 2‐bromopropionate, and 1‐phenylethyl bromide. The polymerization requires the presence of Al(OiPr)₃ and occurs uncontrollably as a conventional radical process. The variation of the molar ratio of the components of the reaction mixture, such as initiator, Al(OiPr)₃ and catalyst, affected the polymerization rates and the molecular weights but did not improve the control. A certain level of control has been achieved by adding 0.5 eq of SnCl₂ as a reducing agent. Tin(II) chloride decreased the rate of polymerization and simultaneously the molecular weights became conversion‐dependent and the polydispersities were also narrowed. Remarkably, the level of control was radically improved in the presence of excess of the poorly soluble catalyst ( 1 ), when the added amount of ( 1 ) was not soluble any more, i.e., under heterogeneous conditions, the system became adjustable and the living polymerization of all three monomers was finally achieved. Possible mechanisms of the ( 1 )‐catalyzed polymerization are discussed. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4193–4204, 2008     

Sequential photodecomposition of bisacylgermane type photoinitiator: Synthesis of block copolymers by combination of free radical promoted cationic and free radical polymerization mechanisms

A block copolymer of cyclohexene oxide (CHO) and styrene (St) was prepared by using bifunctional visible light photoinitiator dibenzoyldiethylgermane (DBDEG) via a two‐step procedure. The bifunctionality of the photoinitiator pertains to the sequential photodecomposition of DBDEG through acyl germane bonds. In the first step, photoinitiated free radical promoted cationic polymerization of CHO using DBDEG in the presence of diphenyliodonium hexafluorophosphate (Ph₂I⁺PF) was carried out to yield polymers with photoactive monobenzoyl germane end groups. These poly(cyclohexene oxide) (PCHO) prepolymers were used to induce photoinitiated free radical polymerization of styrene (St) resulting in the formation of poly(cyclohexene oxide‐block‐styrene) (P(CHO‐b‐St)). Successful blocking has been confirmed by a strong change in the molecular weight of the prepolymer and the block copolymer as well as NMR, IR, and DSC spectral measurements. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4793–4799, 2009     

Living/controlled radical polymerization of styrene with a new initiating system: DCDPS/FeCl3/PPh3

The living/controlled radical polymerization of styrene was investigated with a new initiating system, DCDPS/FeCl₃/PPh₃, in which diethyl 2,3‐dicyano‐2,3‐diphenylsuccinate (DCDPS) was a hexa‐substituted ethane thermal iniferter. The polymerization mechanism belonged to a reverse atom transfer radical polymerization (ATRP) process. The polymerization was controlled closely in bulk (at 100 °C) or in solution (at 110 °C) with a high molecular weight and quite narrow polydispersity (M_w/M_n = 1.18 ∼ 1.28). End‐group analysis results by ¹H NMR spectroscopy showed that the polymer was ω‐functionalized by a chlorine atom, which also was confirmed by the result of a chain‐extension reaction in the presence of a FeCl₂/PPh₃ or CuCl/bipy (2,2′‐bipyridine) catalyst via a conventional ATRP process. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 101–107, 2000     

Polymerization of o‐quinodimethanes. IV. Radical polymerization of 1‐cyano‐o‐quinodimethane in the presence of TEMPO

The radical polymerization behavior of 1‐cyano‐o‐quinodimethane generated by thermal isomerization of 1‐cyanobenzocyclobutene in the presence of 2,2,6,6‐tetramethylpiperidine‐N‐oxide (TEMPO) and the block copolymerization of the obtained polymer with styrene are described. The radical polymerization of 1‐cyanobenzocyclobutene was carried out in a sealed tube at temperatures ranging from 100 to 150 °C for 24 h in the presence of di‐tert‐butyl peroxide (DTBP) as a radical initiator and two equivalents of TEMPO as a trapping agent of the propagation end radical to obtain hexane‐insoluble polymer above 130 °C. Polymerization at 150 °C with 5 mol % of DTBP in the presence of TEMPO resulted in the polymer having a number‐average molecular weight (M_n ) of 2900 in 63% yield. The structure of the obtained polymer was confirmed as the ring‐opened polymer having a TEMPO unit at the terminal end by ¹H NMR, ¹³C NMR, and IR analyses. Then, block copolymerization of the obtained polymer with styrene was carried out at 140 °C for 72 h to give the corresponding block copolymer in 82% yield, in which the unimodal GPC curve was shifted to a higher molecular weight region. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3434–3439, 2000     

Synthesis of poly(methyl methacrylate)‐b‐polystyrene containing a crown ether unit at the junction point via combination of atom transfer radical polymerization and nitroxide mediated radical polymerization routes

Poly(methyl methacrylate)‐b‐polystyrene (PMMA‐b‐PS) containing a benzo‐15‐crown‐5 unit at the junction point was prepared by combining atom transfer radical polymerization and nitroxide‐mediated radical polymerization. For this purpose, 6,7,9,10,12,13,15,16‐octahydro‐5,8,11,14,17‐pentaoxa‐benzocyclopentadecene‐2‐carboxylic acid 3‐(2‐bromo‐2‐methyl‐propionyloxy)‐2‐methyl‐2‐[2‐phenyl‐2‐(2,2,6,6‐tetramethyl‐piperidin‐1‐yloxy)‐ethoxycarbonyl]‐propyl ester ( 3 ) was synthesized and used as an initiator in atom transfer radical polymerization of methyl methacrylate in the presence of CuCl and pentamethyldiethylenetriamine at 60°C. A linear behavior was observed in both plots of ln([M]₀/[M]) versus time and M_n,_GPC versus conversion indicating that the polymerization proceeded in a controlled/living manner. Thus obtained PMMA precursor was used as a macroinitiator in nitroxide‐mediated radical polymerization of styrene (St) at 125°C to give well‐defined PMMA‐b‐PS with crown ether per chain. Kinetic data were also obtained for copolymerization. Moreover, potassium picrate (K⁺ picrate) complexation of 3 and PMMA‐b‐PS copolymer was studied. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3242–3249, 2006     

Novel dinitroxide mediating agent for stable free‐radical polymerization

A novel dinitroxide mediating agent that was suitable for stable free‐radical polymerization was synthesized and used in the block copolymerization of styrene and t‐butyl styrene. Quantitative yields of a novel dinitroxide based on 1,6‐hexamethylene diisocyanate and 4‐hydroxy‐2,2,6,6‐tetramethyl‐1‐piperidinyloxy were obtained. Various experimental parameters, including the nitroxide‐to‐initiator molar ratio, were examined, and it was determined that the polymerization was most controlled under conditions similar to those of conventional 2,2,6,6‐tetramethyl‐1‐piperidinyloxy‐mediated stable free‐radical polymerization. Moreover, the dinitroxide mediator proved to be a viable route for the facile two‐step synthesis of triblock copolymers of styrene and t‐butyl styrene. However, the dinitroxide mediation process resulted in a higher than expected level of nitroxide decomposition, which resulted in polymers possessing a terminal alkoxyamine and an adjacent hydroxylamine rather than a preferred internal bisalkoxyamine. This decomposition resulted in the formation of diblock copolymer species during the triblock copolymer synthesis. Gel permeation chromatography was used to monitor the chain‐end decomposition kinetics, and the determined observed rate constant (5.89 × 10^?5 s^?1) for decomposition agreed well with previous studies for other dinitroxide mediating agents. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1547–1556, 2004     

Direct through anionic,cationic, and radical active species: Terminal carbon–halogen bond for “controlled”/living polymerizations of styrene

In this work, we examined the synthesis of novel block (co)polymers by mechanistic transformation through anionic, cationic, and radical living polymerizations using terminal carbon–halogen bond as the dormant species. First, the direct halogenation of growing species in the living anionic polymerization of styrene was examined with CCl₄ to form a carbon–halogen terminal, which can be employed as the dormant species for either living cationic or radical polymerization. The mechanistic transformation was then performed from living anionic polymerization into living cationic or radical polymerization using the obtained polymers as the macroinitiator with the SnCl₄/n‐Bu₄NCl or RuCp^*Cl(PPh₃)/Et₃N initiating system, respectively. Finally, the combination of all the polymerizations allowed the synthesis block copolymers including unprecedented gradient block copolymers composed of styrene and p‐methylstyrene. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 465–473     

Well‐defined polyoxazoline‐based alkoxyamines as efficient macroinitiators in nitroxide‐mediated radical polymerization of styrene

The synthesis of two well‐defined 2,2,5‐trimethyl‐4‐phenyl‐3‐azahexane‐3‐nitroxide‐terminated poly(2‐methyl‐2‐oxazoline) with narrow dispersity (M_w/M_n = 1.1) has been achieved for the first time. The insertion of the alkoxyamine end groups at one or both ends of poly(2‐methyl‐2‐oxazoline) (PMEOX) chains has been successfully done using a method based on “terminating reagent method.” These macroinitiators have molecular weights ranging from 6.3 × 10³ to 9.4 × 10³ g mol^?1. In contrast, attempt to introduce the alkoxyamine group at one end of PMEOX chain through the “initiator method” has furnished a mixture of alkoxyamine‐graft polyoxazolines because of rearrangement of alkoxyamine occurring during the synthesis of PMEOX. The macroinitiators obtained by terminating reagent method have been used successfully for polymerization of styrene by nitroxide‐mediated radical polymerization (NMP), which exhibited all the expected features of a controlled system. The control of NMP has been proved by a good agreement between theoretical and experimental molecular weights and by narrow dispersity (M_w/M_n < 1.2). Different types of well‐defined multiblock copolymers have been prepared: diblock copolymers poly[(2‐methyl‐2‐oxazoline)‐b‐(styrene)] (PMEOX‐b‐PS) and, for the first time, triblock copolymers poly[(styrene)‐b‐(2‐methyl‐2‐oxazoline)‐b‐(styrene)] (PS‐b‐PMEOX‐b‐PS). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Atom transfer radical polymerization of styrene using the novel initiator ethyl 2‐N,N‐(diethylamino)dithiocarbamoyl‐butyrate

The atom transfer radical polymerizations (ATRPs) of styrene initiated by a novel initiator, ethyl 2‐N,N‐(diethylamino)dithiocarbamoyl‐butyrate (EDDCB), in both bulk and solution were successfully carried out in the presence of copper(I) bromide (CuBr) and N,N,N′,N″,N″‐pentamethyldiethylenetriamine at 115 °C. The polymerization rate was first‐order with respect to the monomer concentration, and the molecular weights of the obtained polymers increased linearly with the monomer conversions with very narrow molecular weight distributions (as low as 1.17) up to higher conversions in both bulk and solution. The polymerization rate was influenced by various solvents in different degrees in the order of cyclohexanone > dimethylformamide > toluene. The molecular weight distributions of the produced polymers in cyclohexanone were higher than those in dimethylformamide and toluene. The results of ¹H NMR analysis and chain extension confirmed that well‐defined polystyrene bearing a photo‐labile N,N‐(diethylamino)dithiocarbamoyl group was obtained via ATRP of styrene with EDDCB as an initiator. The polymerization mechanism for this novel initiation system is a common ATRP process. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 32–41, 2006     

The efficient cyclopolymerization of silyl‐tethered styrenic difunctional monomers

The synthesis and characterization of innovative difunctional styrene‐based monomers and their cyclopolymerization is reported. Difunctional silyl‐based protecting groups with different steric hindrance (either methyl/phenyl or phenyl/phenyl) are used as “tethers” for two 4‐vinylbenzyl reactive moieties. We demonstrate that efficient cyclopolymerization, performed under free‐radical conditions or RAFT‐mediated, takes place for both monomers. RAFT polymerization allows excellent control of M_n and higher degree of polymerization when compared to uncontrolled radical polymerization, yet not optimal control of dispersities. The silyl tethering group could be removed to afford poly(p‐hydroxymethylstyrene). Thermogravimetric analysis (TGA) demonstrates the thermal robustness of the new cyclopolymers, and gives an insight on the ability of the corresponding deprotected polymer to chelate metals ions. The described strategy opens possibilities to achieve sequence control through a cyclopolymerization/tether removal strategy, when having two suitable aromatic systems with opposing electronic character and reactivities in chain cyclopolymerization. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1593–1599