Calorimetric and Dielectric Study of the Segmented Biodegradable Poly(ester‐urethane)s Based on Bacterial Poly[(R)‐3‐hydroxybutyrate]

Two series of segmented poly(ester‐urethane)s were synthesized from bacterial poly[(R)‐3‐hydroxybutyrate]‐diol (PHB‐diol), as hard segments, and either poly(ε‐caprolactone)‐diol (PCL‐diol) or poly(butylene adipate)‐diol (PBA‐diol), as soft segments, using 1,6‐hexamethylene diisocyanate as a chain extender. The hard‐segment content varied from 0 to 50 wt.‐%. These materials were characterized using ¹H NMR spectroscopy and GPC. The polymers obtained were investigated calorimetrically and dielectrically. DSC showed that the T_g of either the PCL or PBA soft segments are shifted to higher temperatures with increasing PHB hard‐segment content, revealing that either the PCL or PBA are mixed with small amounts of PHB in the amorphous domains. The results also showed that the crystallization of soft or hard segments was physically constrained by the microstructure of the other crystalline phase, which results in a decrease in the degree of crystallinity of either the soft or hard segments upon increase of the other component. The dielectric spectra of poly(ester‐urethane)s, based on PCL and PHB, showed two primary relaxation processes, designated as α_S and α_H, which correspond to glass–rubber transitions of PCL soft and PHB hard segments, respectively. Whereas in the case of other poly(ester‐urethane)s, derived from PBA and PHB, only one relaxation process was observed, which broadens and shifts to higher temperature with increasing PHB hard‐segment content. It was concluded from these results that our investigated materials exhibit micro‐phase separation of the hard and soft segments in the amorphous domains.     

Pi‐conjugated chain extenders for the synthesis of optoelectronic segmented polyurethanes

The optical properties of mechanochromic materials change under mechanical stress. Segmented polyurethanes are elastomers composed of amorphous, saturated chain soft segments, and rigid pi‐conjugated hard domains. Within aggregates of hard domains pi–pi interactions may form and result in perturbation of the optoelectronic properties of the system. Disruption and restoration of these electronic interactions within the material may lead to observable mechanochromic response. A series of oligothiophene diols and diamines, as well as a naphthalene diimide diol, have been synthesized for incorporation into the hard domains of segmented polyurethanes and polyureas using long poly(tetramethylene oxide) chains as soft segments. The resulting polymers were evaluated to determine their extent of polymerization and their thermal stability. The optical properties of the materials were studied in solution and as thin films. Where possible the electrochemical properties of the polymers were also explored. The length of the soft segment chains in the segmented polyurethanes hindered electronic coupling of hard domains. Future work involving smaller, more solubilizing soft segments may allow for easier material characterization and mechanochromic response. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Poly(caprolactone) containing highly branched segmented poly(ester urethane)s via A2 with oligomeric B3 polymerization

Highly branched, poly(caprolactone) (PCL) containing segmented poly(ester urethane)s were synthesized via polymerization of A₂ and oligomeric B₃ type monomers. An isocyanate functional butanediol‐based A₂ hard segment was synthesized and immediately reacted with a poly(caprolactone)‐based trifunctional (B₃) soft segment. Characterization of thermal properties using DMA and DSC analysis demonstrated that the PCL segment remained amorphous in branched poly(ester urethane)s. Conversely, the crystallinity of PCL segment was retained to some extent in a linear analogue with equivalent soft segment molecular weight. Tensile testing revealed a slight decrease in Young's modulus and tensile strength for the highly branched polymers compared with a linear analogue. However, highly branched poly(ester urethane)s demonstrated lower hysteresis. In addition to synthesis of highly branched polymers, poly(ester urethane) networks were synthesized from a highly branched hydroxyl‐terminated precursor and a low molar mass diisocyanate as the crosslinking agent. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6285–6295, 2008     

Synthesis and characterization of semicrystalline cycloaliphatic polyester/poly(dimethylsiloxane) segmented copolymers

High molecular weight poly(dimethylsiloxane)/semicrystalline cycloaliphatic polyester segmented copolymers based on dimethyl-1,4-cyclohexane dicarboxylate were prepared and characterized. The copolymers were synthesized using a high trans content isomer that afforded semicrystalline morphologies. Aminopropyl-terminated poly(dimethylsiloxane) (PDMS) oligomers of controlled molecular weight were synthesized, end capped with excess diester to form a diester-terminated oligomer, and incorporated via melt transesterification step reaction copolymerization. The molecular weight of the polysiloxane and chemical composition of the copolymer were systematically varied. The polysiloxane segment was efficiently incorporated into the copolymers via an amide link and its structure was unaffected by low concentrations of titanate transesterification catalyst, as shown by control melt experiments. The homopolymer and copolymers were characterized by solution, thermal, mechanical, and surface techniques. The segmented copolymers were microphase separated as determined by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and by transmission electron microscopy (TEM). It was demonstrated that relatively short poly(dimethylsiloxane) segment lengths and compositions were required to maintain single phase melt polymerization conditions. This was, in fact, the key to the successful preparation of these materials. The copolymers derived from short poly(dimethylsiloxane) segments demonstrated good mechanical properties, melt viscosities representative of single phase polymer melts, and were easily compression molded into films. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 3495–3506, 1997     

Preparation and characterization of N‐methyl‐substituted polyurethane

We prepared N‐methyl‐substituted polyurethanes with different substitution degrees from sodium hydride, methyl p‐toluene sulfonate, and polyether–polyurethane containing poly(oxytetramethylene) glycol, 4,4′‐diphenylmethane diisocyanate, and 1,4‐butanediol. The chemical structures were characterized with Fourier transform infrared and ¹H NMR. To investigate the effects of the N‐substitution degree on the morphology, thermal stability, and mechanical properties, we used differential scanning calorimetry, thermogravimetric analysis, and a universal testing machine. As the substitution degree increased, the new free (1708 cm^?1) and bonded (1650 cm^?1) carbonyl peaks increased. There was no bonded carbonyl peak in fully substituted polyurethane because the urethane groups had no hydrogen. At a small substitution degree, we observed a slight increase in the glass‐transition temperature and decrease in the endotherms of soft‐segment and hard‐segment domains due to the decrease in the hard‐segment domain and the increase in the urethane groups in the soft‐segment domain. The hard‐segment domain decreased and then disappeared as the N‐methyl substitution degree increased. These changes in the morphology resulted (1) in decreased modulus and tensile strength for the films because of the decrease in physical crosslinking points and (2) improved thermal stability as the substitution degree increased. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4077–4083, 2002     

Positron annihilation properties of copolyimides and copolyamides with microphase‐separated structures

The positron annihilation lifetime (PAL) of a series of copolyimides and copolyamides with microphase‐separated structures was measured to investigate the effects of different hard‐segment polymers on the PAL properties of soft‐segment domains of poly(dimethyl‐siloxane) (PDMS) and poly(ethylene oxide) (PEO). The lifetime (τ₃) and intensity (I₃) of the long‐lived component are given as a function of the PDMS or PEO content for a series of copolymers, of which the density roughly obeys the additive rule except for the PDMS‐segmented copolyamides. The PDMS‐segmented copolyimides and copolyamides show much smaller I₃ values than those estimated from the additive rule. The lifetime distribution of the long‐lived component for the PDMS‐segmented copolyamides is composed of two components. The longer‐lifetime component is attributed to pure PDMS domains, and the shorter‐lifetime component is attributed to the polyamide domains, intermediate phases, and PDMS domains containing small amounts of short amide blocks. Despite the high PDMS content, the latter component is rather large. Thus, the positronium formation in the PDMS domains of the copolyimides and copolyamides is effectively reduced. This can be explained by the combination of the difference in the electron affinity of the PDMS and polyimide or polyamide segments and the incomplete phase separation. The PEO‐segmented copolyimides show much smaller I₃ values than those predicted from the additive rule. This is likely attributable to the effects of the intermediate phases. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1123–1132, 2000     

Synthesis and characterization of model diblock copolymers of poly(dimethylsiloxane) with poly(1,4‐butadiene) or poly(ethylene)

Model diblock copolymers of poly(1,4‐butadiene) (PB) and poly(dimethylsiloxane) (PDMS), PB‐b‐PDMS, were synthesized by the sequential anionic polymerization (high vacuum techniques) of butadiene and hexamethylciclotrisiloxane (D₃) in the presence of sec‐BuLi. By homogeneous hydrogenation of PB‐b‐PDMS, the corresponding poly(ethylene) and poly(dimethylsiloxane) block copolymers, PE‐b‐PDMS, were obtained. The synthesized block copolymers were characterized by nuclear magnetic resonance (¹H and ¹³C NMR), size‐exclusion chromatography (SEC), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), transmission electron microscopy (TEM), and rheology. SEC combined with ¹H NMR analysis indicates that the polydispersity index of the samples (M_w/M_n) is low, and that the chemical composition of the copolymers varies from low to medium PDMS content. According to DSC and TGA experiments, the thermal stability of these block copolymers depends on the PDMS content, whereas TEM analysis reveals ordered arrangements of the microphases. The morphologies observed vary from spherical and cylindrical to lamellar domains. This ordered state (even at high temperatures) was further confirmed by small‐amplitude oscillatory shear flow tests. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1579–1590, 2006     

Synthesis and characterization of a novel biodegradable,thermoplastic polyurethane elastomer

A series of biodegradable, thermoplastic polyurethane elastomers poly(?‐caprolactone‐co‐lactide(polyurethane [PCLA–PU] were synthesized from a random copolymer of L ‐lactide (LA) and ?‐caprolactone (CL), hexamethylene diisocyanate, and 1,4‐butanediol. The effects of the LA/CL monomer ratio and hard‐segment content on the thermal and mechanical properties of PCLA–PUs were investigated. Gel permeation chromatography, IR, ¹³C NMR, and X‐ray diffraction were used to confirm the formation and structure of PCLA–PUs. Through differential scanning calorimetry, tensile testing, and tensile‐recovery testing, their thermal and mechanical properties were characterized. Their glass‐transition temperatures were below ?8 °C, and their soft domains became amorphous as the LA content increased. They displayed excellent mechanical properties, such as a tensile strength as high as 38 MPa, a tensile modulus as low as 10 MPa, and an elongation at break of 1300%. Therefore, they could find applications in biomedical fields, such as soft‐tissue engineering and artificial skin. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5505–5512, 2006     

Polyisobutylene‐based segmented polyureas. I. Synthesis of hydrolytically and oxidatively stable polyureas

Novel segmented polyurea elastomers containing soft polyisobutylene (PIB) segments were synthesized and characterized. The key ingredient, primary amine‐telechelic PIB oligomers (NH₂‐PIB‐NH₂) with number average molecular weights of 2500 and 6200 g/mol were synthesized. PIB‐based polyureas were prepared by using various aliphatic diisocyanates and diamine chain extenders with hard segment contents between 9.5 and 46.5% by weight. All copolymers displayed microphase morphologies as determined by dynamic mechanical analysis. Tensile strengths of nonchain‐extended and chain‐extended polyureas showed a linear dependence on the urea hard segment content. PIB‐based polyureas prepared with NH₂‐PIB‐NH₂ of M_n = 2500 g/mol, 4,4′‐methylendbis(cyclohexylisocyantate), and 1,6‐diaminohexane containing 45% hard segment exhibited 19.5 MPa tensile strength which rose to 23 MPa upon annealing at 150 °C for 12 h. With increasing hard segment content, elongation at break decreased from ～ 450% to a plateau of 110%. The hydrolytic and oxidative stability of PIB‐based polyureas were unprecedented. Although commercial “oxidatively resistant” thermoplastic polyurethanes degraded severely upon exposure to boiling water or concentrated nitric acid, the experimental polyureas survived without much degradation in properties. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 38–48, 2009     

Biobased polyurethanes from polyether polyols obtained by ionic‐coordinative polymerization of epoxidized methyl oleate

A series of poly(ether urethane) networks were synthesized from polyether polyols obtained by ionic‐coordinative polymerization of epoxidized methyl oleate (EMO) using 4,4′‐methylenebis(phenyl isocyanate) or l ‐lysine diisocyanate as coupling agents. Moreover, a variety of segmented poly(ether urethane) networks with different hard segment contents were obtained using 1,3‐propanediol as the chain extender. The materials were characterized by differential scanning calorimetry, thermogravimetric analysis, dynamic mechanical thermal analysis, and tensile properties. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Well‐defined PE‐b‐PDMS diblock copolymers via the combination of thiol‐ene click and esterification reactions: Facile synthesis and compatibilization for HDPE/silicone oil blends

Well‐defined diblock copolymers of linear polyethylene (PE) and poly(dimethylsiloxane) (PDMS) have been synthesized through a facile route combining the thiol‐ene click chemistry of vinyl‐terminated polyethylene (PE‐ene) and the sequential esterification reaction. The resulting diblock copolymers are characterized by ¹H NMR, FT‐IR, DSC, TGA, and TEM. In addition, the PE‐b‐PDMS diblock copolymers have been evaluated as compatibilizers in the blends of high‐density polyethylene (HDPE) and silicone oil. The morphological analysis and mechanical properties demonstrate that the compatibilized blends with low loading concentration of PE‐b‐PDMS display significant improvements in modulus of elasticity and elongation at break as compared to the uncompatibilized binary blends. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3205–3212     

New segmented poly(ester‐urethane)s from renewable resources

The physical and mechanical properties of aliphatic homopolyesters from monomers obtainable from renewable resources, namely, 1,3‐propanediol and succinic acid, were improved by their combination with aromatic urethane segments capable of establishing strong intermolecular hydrogen bonds. Segmented poly(ester‐urethane)s were synthesized from dihydroxy‐terminated oligo(propylene succinate)s chain‐extended with 4,4′‐diisophenylmethane diisocyanate. The newly synthesized materials were exhaustively characterized by ¹H NMR spectroscopy, size exclusion chromatography, differential scanning calorimetry, dynamic mechanical analysis, and with respect to their main static mechanical properties, an Instron apparatus was used. The average repeat number of the hard segments, evaluated by NMR, ranged from 4 to 9, whereas that of the flexible segments was about 14. The degree of crystallinity, glass‐transition temperature, melting point, tensile strength, elongation, and Young's modulus were influenced by the ratio between hard and soft segments of the segmented copolymer in a predictable way. The results demonstrated that poly(ester‐urethane)s from 1,3‐propanediol and succinic acid are promising thermoplastics. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 630–639, 2001     

Synthesis and characterization of model polybutadiene‐1,4‐b‐polydimethylsiloxane‐b‐polybutadiene‐1,4 copolymers

Model copolymers of poly(butadiene) (PB) and poly(dimethylsiloxane) (PDMS), PB‐b‐PDMS‐b‐PB, were synthesized by sequential anionic polymerization (high vacuum techniques) of 1,3‐butadiene and hexamethylciclotrisiloxane (D₃) on sec‐BuLi followed by chlorosilane‐coupling chemistry. The synthesized copolymers were characterized by nuclear magnetic resonance (¹H NMR), size‐exclusion chromatography (SEC), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). SEC and ¹H NMR results showed low polydispersity indexes (M_w/M_n) and variable siloxane compositions, whereas DSC and TGA experiments indicated that the thermal stability of the triblock copolymers depends on the PDMS composition. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2726–2733, 2007     

Control of hard segment size in polyurethane formation

In general, segmented polyurethane elastomers are prepared by reacting an isocyanate-capped polyol prepolymer with a short-chain diol chain extender, yielding an elastomer with hard segments of uniform size. However, the hard segment size will not be uniform if the polyurethane polymer is prepared by forming the hard segment first, followed by soft segment formation. Because the mechanical properties of polyurethane elastomers depend on the relative ratio of the hard to soft segments as well as the effectiveness of the hard segment as a physical crosslinker, the control of the size distribution of the hard segment is a key factor in designing polyurethane elastomers. It was found that reaction conditions can affect the size distribution of hard segments derived from an aliphatic diisocyanate with differential reactivity between the two isocyanate groups. Lower reaction temperatures and simultaneous mixing of all reactants gave the preferred size distribution of hard segments. © 1995 John Wiley & Sons, Inc.     

Self‐assembly and morphology of polydimethylsiloxane supramolecular thermoplastic elastomers

Functionalization of polydimethylsiloxanes (PDMS) polymers with hydrogen‐bonding ureidopyrimidinone (UPy) groups leads to supramolecular thermoplastic elastomers. In previous studies, no lateral stacking of UPy dimers was observed in UPy‐functionalized polymers, unless additional urethane or urea groups were built into the hard block. However, we have shown that when PDMS is used as the soft block, this lateral aggregation of UPy dimers does take place, since long fibers could be observed in the atomic force microscopy (AFM) phase image. Also in bulk, the presence of these interactions was proven by oscillatory shear experiments. We attribute this aggregation to the incompatibility of soft block and hard block, leading to phase separation. Moreover, we have shown that additional urethane or urea groups in the hard block do lead to materials with more fibers and higher melting points. For the UPy‐urea functionalized PDMS even single fibers are observed with AFM when dropcasted from a very diluted solution. When the length of the soft block is increased, the morphology changes from fibrous to spherical. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3877–3885, 2008     

Morphology of polyurethanes with triol monomer crosslinked on hard segments

Polyester‐based polyurethanes containing ≈60 wt % of polyester were synthesized from low molecular weight polyester (M_n ≈2000) and 4,4′‐methylene bis(phenyl isocyanate) (MDI), with butanediol as a chain extender and glycerol as a crosslinker. The triol crosslinker was used in substitution for the 1,4‐butanediol chain extender; thus, the crosslinker was chemical bonded to the hard segments of polyurethane. The morphologies of these polyurethanes were studied by differential scanning calorimetry (DSC), small‐angle X‐ray scattering (SAXS), TMA (thermal mechanical analysis), and FTIR (Fourier transform infrared spectroscopy). Owing to the highly steric hindrance, the presence of triol crosslinker in the hard segments resulted in a decrease in the aggregation of hard segments through hydrogen bonding. The experimental results revealed that the degree of phase segregation of soft and hard segments decreased with increasing the triol crosslinker content in the hard segments. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2673–2681, 1999     

Structure and physical properties of segmented polyurethane elastomers containing chemical crosslinks in the hard segment

Two series of segmented polyurethanes, one containing 50% soft segments and the other with 70% soft segments were synthesized. Chemical crosslinks were introduced through the hard segment in a controlled way. Chemical polyurethane networks were characterized by swelling. The effect of the degree of crosslinking on properties was examined. It was found that chemical crosslinks in the hard segment reduce the mobility of the soft phase and destroy the crystallinity of the hard phase, but they improve heat stability of the hard domains. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36 : 221–235, 1998     

Poly(ester urethane)s with polycaprolactone soft segments: A morphological study

Two series of poly(ester urethane)s were prepared, containing polycaprolactone (PCL) as the soft segment with molecular weights of 530 and 2000. In each series, the soft‐segment/hard‐segment ratio was varied, and the morphological changes were monitored with differential scanning calorimetry, dynamic mechanical thermal analysis, wide‐angle X‐ray scattering, and scanning electron microscopy techniques. The polyurethanes with longer PCL segments retained their crystallinity, whereas those with shorter PCL segments did not. A morphological model is proposed, in which a continuous PCL‐rich matrix contains both PCL crystallites and domains of urethane hard segments. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4117–4130, 2002     

Structure and properties of segmented poly(urethaneurea)s with relatively short hard‐segment chains

We report the structure and properties of segmented poly(urethaneurea) (SPUU) with relatively short hard‐segment chains. The SPUU samples comprised poly(tetramethylene glycol) prepolymer as a soft segment and 4,4′‐diphenylmethane diisocyanate (MDI) units as a hard segment that were extended with ethylenediamine. To discuss quantitatively the conformation of the soft‐segment chain in the microphase‐separated domain space, we used SPUU samples for which the molecular weights of the hard‐ and soft‐segment chains are well characterized. The effects of the cohesive force in the hard‐segment chains on the structure and properties of SPUU were also studied with samples of different chain lengths of the hard segment, although the window of x_H, the average number of MDI units in a hard‐segment chain, was narrow (2.38 ≤ x_H ≤ 2.77). There were urethane groups in the soft segments and urea groups in the hard segments. Because of a strong cohesive force between the urea groups, we could control the overall cohesive force in the hard‐segment chains by controlling the chain lengths of the hard segment. First of all, microphase separation was found to be better developed in the samples with longer hard‐segment chains because of an increase of the cohesive force. It was also found that the interfacial thickness became thinner. The long spacing for the one‐dimensionally repeating hard‐ and soft‐segment domains could be well correlated with the molecular characteristics when the assumption of Gaussian conformation was employed for the soft‐segment chains. This is unusual for strongly segregated block copolymers and might be characteristic of multiblock copolymers containing rod–coil chains. The tensile moduli and thermal stability temperature, T_H, increased with an increase of the cohesive force, whereas the glass‐transition temperature, the melting temperature, and the degree of crystallinity of the soft‐segment chains decreased. The increase in T_H especially was appreciable, although the variation in the chain length of the hard segment was not profound. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1716–1728, 2000     

1,5-萘二异氰酸酯与1,4-丁二醇基为基质的多嵌段聚氨酯弹性体的合成与性能

利用 1 ,5_萘二异氰酸酯 (NDI)和 1 ,4_丁二醇 (BDO)为均匀硬质分子单体 ,与不同软质分子单体 (聚醚、聚酯、聚硅氧烷 )缩合制备多嵌段聚氨酯弹性体 ,详细研究了硬嵌段相 (NDI)弹性体的结构与性能间的关系 ,发现随着硬嵌段相长度的增加 ,或者氨基甲酸酯中胺基与聚醚、聚酯、聚硅氧烷中软段氧原子间氢键的减弱 ,都导致微相分离程度的增加 ,造成聚合物熔点和熔化热的升高。硬嵌段相熔化的多峰行为是由于形成了NDI/BDO半微晶区 ,在退火时转变为更加有序的结晶微区 ,当温度高于 1 80℃时 ,由于氢键的断裂 ,NDI/BDO硬嵌段发生分解反应 ,该过程源于不很有序的硬嵌段半结晶微区。当温度高于 2 5 0℃时 ,发生快速的分解。在动态力学行为方面 ,NDI基聚醚弹性体比其它硅氧烷基的弹性体展示了更高的硬嵌段区的稳定性 ,同时 ,在使用温度范围内 ,也显示出最高的储能模量值 ,表明刚性对温度的依赖性 ,以及NDI/BDO硬嵌段中活性填料的显著影响