Investigation by combined solid‐state NMR and SAXS methods of the morphology and domain size in polystyrene‐b‐polyethylene oxide‐b‐polystyrene triblock copolymers

The microphase structure of a series of polystyrene‐b‐polyethylene oxide‐b‐polystyrene (SEOS) triblock copolymers with different compositions and molecular weights has been studied by solid‐state NMR, DSC, wide and small angle X‐ray scattering (WAXS and SAXS). WAXS and DSC measurements were used to detect the presence of crystalline domains of polyethylene‐oxide (PEO) blocks at room temperature as a function of the copolymer chemical composition. Furthermore, DSC experiments allowed the determination of the melting temperatures of the crystalline part of the PEO blocks. SAXS measurements, performed above and below the melting temperature of the PEO blocks, revealed the formation of periodic structures, but the absence or the weakness of high order reflections peaks did not allow a clear assessment of the morphological structure of the copolymers. This information was inferred by combining the results obtained by SAXS and ¹H NMR spin diffusion experiments, which also provided an estimation of the size of the dispersed phases of the nanostructured copolymers. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 55–64, 2010     

Investigation of the deformation of homogeneous poly(ethylene‐co‐1‐octene) by wide‐ and small‐angle X‐ray scattering using synchrotron radiation

The deformation behavior of homogeneous ethylene‐1‐octene copolymers was investigated as a function of the crystallinity and the crystal size and perfection, respectively, by wide‐ and small‐angle X‐ray scattering using synchrotron radiation. The crystallinity and the crystal size and perfection, respectively, are controlled by the copolymer composition and the condition of melt crystallization. The deformation includes rotation of crystals, followed by plastic deformation and complete melting of the initial crystal population, and final formation of microfibrils. The process of rotation, plastic deformation, and melting of crystals of the initial structure is completed at lower strain if the size and perfection of the crystals, respectively, decrease, that is, if crystals thermally melt at lower temperature. The kinetics of the fibrillation of the initial structure seems independent of the crystal symmetry, that is, rotation and melting of pseudohexagonal and orthorhombic polyethylene crystals (as evident in low‐crystalline specimens) are similar. The structure of the microfibrils, before and after stress release, is almost independent of the condition of prior melt crystallization, which supports the notion of complete melting of the initial crystal population. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1919–1930, 2002     

Structure evolution of α′‐phase poly(lactic acid)

Poly(lactic acid) films consisting of α′‐forms were prepared and uniaxially drawn. The effects of the draw rate at temperatures above the glass transition temperature on chain conformation, degree of crystallinity, and crystalline phase transformation were investigated by a combination of vibrational spectroscopy (infrared and Raman), differential scanning calorimetry, and wide‐angle X‐ray diffraction (WAXD). It was established that the α′‐crystal's phase of poly(lactic acid) films does not transform into either an α or β crystals on uniaxial drawing at a fixed draw ratio of 4. However, the degree of crystallinity was significantly increased on deformation. The structural change as a function of deformation also promotes an increase in the strain‐induced enthalpic relaxation endothermic peak appearing near the glass transition region. While the overall changes in physical properties can be attributed to the changes in the degree of crystallinity as a function of strain rate, polarized Raman spectra, and WAXD clearly illustrated changes and the differences in the amorphous and crystalline orientation as a function of processing conditions. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1446–1454, 2011     

Systematic coarse‐graining of semicrystalline polyethylene

In an effort to accelerate simulations exploring deformation mechanisms in semicrystalline polymers, we have created structure‐based coarse‐grained (CG) models of polyethylene and evaluated the extent to which they can simultaneously represent its amorphous and crystalline phases. Two CG models were calibrated from target data sampled from atomistic simulations of supercooled oligomer melts that differ in how accurately they represent the distribution of bond lengths between CG sites. Both models yield semicrystalline morphology when simulations are performed at ambient conditions, and both accurately predict the glass transition and melt temperatures. A thorough evaluation of the models was then conducted to assess how well they represent various properties of the amorphous and crystalline phases. We found that the model that more faithfully reproduces the target bond length distribution poorly represents the crystalline phase, which results from its inability to reproduce correlations in the structural distributions. The second model, which utilizes a harmonic bond potential and thus reproduces the target bond length distribution less accurately, represents the structure and chain mobility within the crystalline phase more realistically. Furthermore, the latter model more faithfully reproduces the vastly different relaxation timescales of the phases, a critical feature for modeling deformation mechanisms in semicrystalline polymers. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 331–342     

Relationship between fracture toughness and intrinsic deformation parameters in isotropic and flow‐oriented linear low‐density polyethylene

The fracture toughness of isotropic and flow‐oriented linear low‐density polyethylene (LLDPE) is evaluated by the Essential Work of Fracture (EWF) concept, with a special setup of CCD camera to monitor the process of deformation. Allowing for the molecular orientation, flow‐oriented sample, prepared via melt extrusion drawing, is stretched parallel (oriented‐0°) and perpendicular (oriented‐90°) to its original melt extrusion drawing direction, respectively. The obtained values of specific EFW w_e are 34.6, 10.2, and 4.2 N/mm for the oriented‐0°, isotropic and oriented‐90° sample, respectively. With knowledge of intrinsic deformation parameters deduced from uniaxial tensile tests, moreover, a relationship between specific EFW w_e the ratio of true yield stress to strain hardening modulus σ_ty/G is well established. It means that the fracture toughness of polyethylene is determined by both crystalline and amorphous parts, rather than by one of them. Moreover, the true yield stress seems to be nondecisive factors determining the fracture toughness of polyethylene. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2880–2887, 2006     

Effect of strain‐induced molecular ordering on mechanical performance and barrier properties of polylactide nanocomposites

Plastic deformation of polylactide has been known as a self‐reinforcement alternative to improve mechanical and barrier properties. In this study, the structural evolution was investigated during a hot‐drawing process, at different initial strain rates and temperatures above T_g of polylactide. The drawing process at T_g +10 °C, led to the formation of an intermediate molecular ordering, between the crystalline and amorphous phases. A lower fraction of this mesomorphic phase was found to develop with the addition of nanoparticles. An increase in the stretching temperature to T_g +30 °C, caused an improvement of the crystallization kinetics, compared to that of thermally activated crystallization. A strain hardening behavior was observed in the presence of mesophase during a stretching process of the hot‐drawn films at room temperature. Permeability was discerned to its basic components, diffusivity, and solubility coefficients. The matrix degradation influenced the permeability components. The diffusivity decreases in the presence of the impermeable matters. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1865–1876     

Preparation of oriented β‐form poly(L‐lactic acid) by solid‐state extrusion

Melt‐crystallized, low molecular weight poly(L ‐lactic acid) (PLLA) consisting of α crystals was uniaxially drawn by solid‐state extrusion at an extrusion temperature (T_ext) of 130–170 °C. A series of extrusion‐drawn samples were prepared at an optimum T_ext value of 170 °C, slightly below the melting temperature (T_m) of α crystals (～180 °C). The drawn products were characterized by deformation flow profiles, differential scanning calorimetry (DSC) melting thermograms, wide‐angle X‐ray scattering (WAXD), and small‐angle X‐ray scattering as a function of the extrusion draw ratio (EDR). The deformation mode in the solid‐state extrusion of semicrystalline PLLA was more variable and complex than that in the extensional deformation expected in tensile drawing, which generally gave a mixture of α and β crystals. The deformation profile was extensional at a low EDR and transformed to a parabolic shear pattern at a higher EDR. At a given EDR, the central portion of an extrudate showed extensional deformation and the shear component became progressively more significant, moving from the center to the surface region. The WAXD intensities of the (0010)_α and (003)_β reflections on the meridian as well as the DSC melting thermograms showed that the crystal transformation from the initial α form to the oriented β form proceeded rapidly with increasing EDR at an EDR greater than 4. Furthermore, WAXD showed that the crystal transformation proceeded slightly more rapidly at the sheath region than at the core region. This fact, combined with the deformation profiles (shear at the sheath and extensional at the core), indicated that the crystal transformation was promoted by shear deformation under a high pressure rather than by extensional deformation. Thus, a highly oriented rod consisting of only β crystals was obtained by solid‐state extrusion of melt‐crystallized, low molecular weight PLLA slightly below T_m. The structure and properties of the α‐ and β‐form crystals were also studied. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 95–104, 2002     

Higher order structural analysis of stereocomplex‐type poly(lactic acid) melt‐spun fibers

The higher order structure of stereocomplex‐type poly(lactic acid) melt‐spun fibers of an equimolar blend of poly(L ‐lactic acid) and poly(D ‐lactic acid) was analyzed with wide‐angle X‐ray diffraction (WAXD) and birefringence measurements. Two different crystalline structures were observed in the fibers: α‐form homocrystals and stereocomplex crystals. The weight fractions of the two crystals were estimated with the WAXD integrated intensity data. The crystalline orientation factors were obtained from the WAXD measurements. Well‐oriented homocrystals formed during a drawing process at the crystallization temperature of the homocrystal. Drawing above this temperature caused the stereocomplex crystal to be formed. The crystalline orientation tended to be lower with increasing drawing temperatures. Through the combination of the intrinsic birefringence and the fractions of the α‐form homocrystals and stereocomplex crystals, the birefringence of the amorphous phase was evaluated. The amorphous birefringence stayed positive and decreased with increasing drawing temperature. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 218–228, 2007     

Structure development of polyamide‐66 fibers during drawing and their microstructure characterization

Structure development during drawing was studied for three sets of polyamide‐66 (PA66) fibers with density, optical microscopy, wide‐angle X‐ray diffraction, and Fourier transform infrared spectroscopy. The crystallinity, estimated by density measurements, remained virtually constant with increasing draw ratios, indicating that stress‐induced crystallization did not occur for the PA66 fibers drawn at room temperature, but there was a rapid transformation from a hedrite morphology to a fibrillar one. The absence of stress‐induced crystallization differed from the behavior of polyamide‐6, and this was attributed to the stronger hydrogen bonding between polyamide chains and the higher glass‐transition temperature of PA66. Polarized infrared spectroscopy was used to measure the transition‐moment angles of the vibrations at 936 and 906 cm^?1, which were found to be 48 and 60°, respectively. The crystalline orientation was estimated from the band at 936 cm^?1, and the increase with an increasing draw ratio was in close quantitative agreement with X‐ray diffraction data; this showed that infrared spectroscopy could be used reliably to measure the crystalline orientation of PA66 fibers. Because we were unable to obtain the transition‐moment angle of the amorphous bands, the amorphous orientation was obtained with Stein's equation. The amorphous orientation developed more slowly than the crystalline orientation, which is typical behavior for flexible‐chain polymers. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1940–1948, 2002     

Mechano‐reversible physical aging of elastic oriented syndiotactic polypropylene

Syndiotactic polypropylene (sPP), obtained at 0 °C in the trans‐planar mesophase, was drawn at room temperature up to λ = 6, and left at room temperature for 1 year with fixed or relaxed ends. Data analysis allowed the clarification of the structure of the crystalline phases and their transformations during the aging. In both oriented samples similar structural changes were observed, although they were due to different aging mechanisms. The physical aging led to the crystallization in both samples of an oriented helical form, due to a partial transformation of the mesophase and of the amorphous phase. In the oriented sample aged with fixed ends, a small fraction of the crystalline trans‐planar form III became stable even by releasing the tension after 1 year. This last sample did not undergo the large shrinkage, always observed by unloaded sPP after drawing, and therefore was no more elastic. Also, the sample aged with free ends for 1 year showed a reduced elasticity in terms of both dissipated energy and permanent set. However, after a new deformation up to λ = 6, the fiber recovered its previous elasticity. Indeed a mechano‐reversibility was apparent for the oriented elastic sample of sPP aged at room temperature with free ends, leading to a renewed elasticity. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 599–606, 2008     

Wide‐angle X‐ray diffraction and differential scanning calorimetry study of the crystallization of poly(ethylene naphthalate), poly(butylene naphthalate), and their copolymers

The crystallization behavior of a series of poly(ethylene‐co‐butylene naphthalate) (PEBN) random copolymers was studied. Wide‐angle X‐ray diffraction (WAXD) patterns showed that the crystallization of these copolymers could occur over the entire range of compositions. This resulted in the formation of poly(ethylene naphthalate) or poly(butylene naphthalate) crystals, depending on the composition of the copolymers. Sharp diffraction peaks were observed, except for 50/50 PEBN. Eutectic behavior was also observed. This showed isodimorphic cocrystallization of the PEBN copolymers. The variation of the enthalpy of fusion of the copolymers with the composition was estimated. The isothermal and nonisothermal crystallization kinetics were studied. The crystallization rates were found to decrease as the comonomer unit content increased. The tensile properties were also measured and were found to decrease as the butylene naphthalate content of the copolymers increased. For initially amorphous specimens, orientation was proved by WAXD patterns after drawing, but no crystalline reflections were observed. However, the fast crystallization of drawn specimens occurred when they were heated above the glass‐transition temperature. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 843–860, 2004     

Mechanical properties of oriented low‐density polyethylene with an oriented lamellar‐stack morphology

A quantitative study was undertaken of the anisotropy of low‐strain mechanical behavior for specially oriented polyethylene with controlled crystalline and lamellar orientation. The samples were prepared by the die drawing of injection‐molded rods of polyethylene and annealing. This produced a parallel lamellar structure for which a simple, three‐dimensional composite laminate model could be used to calculate the expected anisotropy. Experimental data, including X‐ray strain measurements of the lateral crystalline elastic constants, showed good quantitative agreement with the model prediction. The X‐ray strain measurements confirmed that the amorphous regions exert large constraints on the crystalline phase in the lateral directions, where an order of magnitude difference was found between the measured apparent lateral crystalline compliances in the lamellar‐stack sample and the expected values for a perfect crystal. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 755–764, 2000     

Elevation of the glass transition temperature in flexible‐chain semicrystalline polymers

In the idealized two‐phase model of a semicrystalline polymer, the amorphous intercrystalline layers are considered to have the same properties as the fully‐amorphous polymer. In reality, these thin intercrystalline layers can be substantially influenced by the presence of the crystals, as individual polymer molecules traverse both crystalline and amorphous phases. In polymers with rigid backbone units, such as poly(etheretherketone), PEEK, previous work has shown this coupling to be particularly severe; the glass transition temperature (T_g) can be elevated by tens of degrees celsius, with the magnitude of the elevation correlating directly with the thinness of the amorphous layer. However, this connection has not been explored for flexible‐chain polymers, such as those formed from vinyl‐type monomers. Here, we examine T_g in both isotactic polystyrene (iPS) and syndiotactic polystyrene (sPS), crystallized under conditions that produce a range of amorphous layer thicknesses. T_g is indeed shown to be elevated relative to fully‐amorphous iPS and sPS, by an amount that correlates with the thinness of the amorphous layer; the magnitude of the effect is severalfold less than that in PEEK, consistent with the minimum lengths of polymer chain required to make a fold in the different cases. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1198–1204, 2007     

Structural development of ultra‐high strength polyethylene fibers: Transformation from kebabs to shishs through hot‐drawing process of gel‐spun fibers

Structural development of ultra‐high strength polyethylene fibers via hot‐drawing processes of as‐spun gel fibers was investigated by means of transmission electron microscopy. It is found that the shish‐kebabs developed in both the as‐spun and drawn fibers can be transformed continuously into the micro‐fibril structure composed mostly of the shish structure through the hot‐drawing process. The structure transformation involves a drastic decrease in diameter of the kebab plus the shish but almost no change in the shish diameter. This result suggests that the chains in the kebabs are incorporated into the shishs and consumed to extend the longitudinal dimension of the shishs during the drawing process. The proposed new deformation model well explains the relationship between the fiber morphology and their mechanical properties: the tensile strength and modulus of the fibers can be determined by the number of the shish in the fiber and the macroscopic diameter of the fiber, which are apriori determined at the spinning process. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1861–1872, 2010     

Melt spinning and laser‐heated drawing of a new semiaromatic polyamide,PA9‐T fiber

Fibers of PA9‐T, a new semiaromatic polyamide containing a long aliphatic chain, were prepared by melt spinning. As‐spun fibers were subsequently drawn with a CO₂ laser‐heated drawing system at different draw ratios and various drawing velocities. On‐line observations of drawing points deciphered two drawing states; namely, flow drawing and neck drawing, over the entire range of drawing. Drawing stress revealed that flow drawing is induced by slight drawing stress under a low draw ratio up to 3, and neck drawing is induced by relatively high drawing stress under a higher draw ratio. The effect of drawing stress and drawing velocity on the development of the structure and properties has been characterized through analysis of birefringence, density, WAXD patterns, and tensile, thermal, and dynamic viscoelastic properties. For the neck‐drawn fibers, almost proportional enhancements of crystallinity and molecular orientation with drawing stress were observed. The flow‐drawn fibers have an essentially amorphous structure, and birefringence and density do not always have a linear relation with properties. The fibers drawn at high drawing speed exhibit improved fiber structure and superior mechanical properties. The maximum tensile strength and Young's modulus of PA9‐T drawn fibers were found to be 652 MPa and 5.3 GPa, respectively. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 433–444, 2004     

Melt drawing of ultra‐high molecular weight polyethylene: Comparison of Ziegler‐ and metallocene‐catalyzed reactor powders

The drawing behavior of the ultra‐high molecular weight polyethylene (UHMW‐PE) melts has been studied by comparing the stress/strain curves for two types of samples as polymerized using conventional Ziegler and newer metallocene catalyst systems. Two UHMW‐PE samples, having the same viscosity average molecular weight of 3.3 × 10⁶, but different molecular weight distribution, have been drawn from melt at special conditions. The sample films for drawing were prepared by compression molding of reactor powders at 180°C in the melt. Differences in the structural changes during drawing and resultant properties, ascribable to their broad or narrow molecular weight distribution, were estimated from tensile tests, SEM observations, X‐ray measurements and thermal analyses. The metallocene‐catalyzed sample having narrower molecular weight distribution, could be effectively drawn from the melt up to a maximum draw ratio (DR) of 20, significantly lower than that obtained for the Ziegler‐catalyzed sample, ∼ 50. The stress/strain curves on drawing were remarkably influenced by draw conditions, including draw temperature and rate. However, the most effective draw for both was achieved at 150°C and a strain rate of 5 min⁻¹, independent of sample molecular weight distribution. The efficiency of drawing, as evaluated by the resultant tensile properties as a function of DR, was higher for the metallocene‐catalyzed sample having narrower molecular weight distribution. Nevertheless, the maximum achieved tensile modulus and strength for the Ziegler sample, 50–55 and 0.90 GPa, respectively, were significantly higher than those for the metallocene sample, 20 and 0.65 GPa, respectively, reflecting the markedly higher drawability for the former than the latter. The stress/strain behavior indicated that the origin of differences during drawing from the melt could be attributed to the ease of chain relaxation for the lower molecular weight chains in the melt. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1921–1930, 1999     

Characterization of the mesostructure of HDPE under “in situ” uniaxial tensile test by incoherent polarized steady‐light transport

This study presents quantitative results related to in situ investigation of the microstructural evolutions of high‐density polyethylene with deformation. These results were obtained thanks to a novel technique (IPSLT) based on the polarized light scattering transport phenomenon. The heterogeneities produced during whitening of the polymer bulk are characterized at the mesoscale level (from hundred of nanometers to a few micrometers). The technique is described as well as the identified parameters it provides, namely: the average size of the scatterers, the anisotropy developed in the medium, and the light transport length, representative of both the volume fraction and size of the heterogeneities. Results obtained during video‐controlled tensile experiments confirm those obtained previously with X‐ray microtomography. They put forward the role of morphological transformations of the amorphous/crystalline phases (especially regarding the creation of fibrillar assemblies) rather than the cavitation phenomenon. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Pressure‐induced amorphization and disordering on cooling in semi‐crystalline polymers: calorimetric evidence for inverse melting in one component system

We report some unusual phase behaviour, of general implication for condensed matter, on the polymer poly‐4‐methyl pentene‐1 (P4MP1) induced by changes in pressure (P) and temperature (T), as observed by in‐situ X‐ray diffraction and high pressure DSC. Upon increasing pressure beyond a threshold value, the polymer, crystalline at ambient conditions, looses its crystalline order isothermally. The process is reversible. This behaviour is observed in two widely separated temperature regions, one below the glass transition temperature (< 50°C) and one close to the melting temperature (250°C), thus showing solid state amorphization and inversion in the melting temperature with increasing pressure. This further suggests inverse melting, i.e. re‐entrant of the two widely separated liquid and amorphous phases along the T‐axis at fixed P. This is confirmed experimentally as disordering in the crystalline structure on cooling. The inverse melting in P4MP1 raises the possibility of exothermic melting and endothermic crystallization as anticipated by Tammann (1903), see reference 1. The anticipated exothermic melting and endothermic crystallization is confirmed experimentally in the one component system P4MP1. We are observing similar features in a range of polymers.     

Multiaxial deformation of polyethylene and polyethylene/clay nanocomposites: in situ synchrotron small angle and wide angle X‐ray scattering study

A unique in situ multiaxial deformation device has been designed and built specifically for simultaneous synchrotron small angle X‐ray scattering (SAXS) and wide angle X‐ray scattering (WAXS) measurements. SAXS and WAXS patterns of high‐density polyethylene (HDPE) and HDPE/clay nanocomposites were measured in real time during in situ multiaxial deformation at room temperature and at 55 °C. It was observed that the morphological evolution of polyethylene is affected by the existence of clay platelets as well as the deformation temperature and strain rate. Martensitic transformation of orthorhombic into monoclinic crystal phases was observed under strain in HDPE, which is delayed and hindered in the presence of clay nanoplatelets. From the SAXS measurements, it was observed that the thickness of the interlamellar amorphous region increased with increasing strain, which is due to elongation of the amorphous chains. The increase in amorphous layer thickness is slightly higher for the nanocomposites compared to the neat polymer. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Interplay between solid state microstructure and photophysics for poly(9,9‐dioctylfluorene) within oriented polyethylene hosts

We present a study of isotropic and uniaxially oriented binary blend films comprising ≤1 wt % of the conjugated polymer poly(9,9‐dioctylfluorene) (PFO) dispersed in both ultra‐high molecular weight (UHMW) and linear‐low‐density (LLD) polyethylene (PE). Polarized absorption, fluorescence and Raman spectroscopy, scanning electron microscopy, and X‐ray diffraction are used to characterize the samples before and after tensile deformation. Results show that blend films can be prepared with PFO chains adopting a combination of several distinct molecular conformations, namely glassy, crystalline, and the so‐called β‐phase, which directly influences the resulting optical properties. Both PFO concentration and drawing temperature strongly affect the alignment of PFO chains during the tensile drawing of the blend films. In both PE hosts, crystallization of PFO takes place during drawing; the resulting ordered chains show optimal optical anisotropy. Our results clarify the PFO microstructure in oriented blends with PE and the processing conditions required for achieving the maximal optical anisotropy. © 2014 The Authors. Journal of Polymer Science Part B: Polymer Physics Published by Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 22–38