High‐quality poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐p‐phenylenevinylene] synthesized by a solid–liquid two‐phase reaction: Characterizations and electroluminescence properties

Poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐p‐phenylenevinylene] (MEH‐PPV) with a molar mass of 26–47 × 10⁴ g mol^?1 and a polydispersity of 2.5–3.2 was synthesized by a liquid–solid two‐phase reaction. The liquid phase was tetrahydrofuran (THF) containing 1,4‐bis(chloromethyl)‐2‐methoxy‐5‐(2′‐ethylhexyloxy)benzene as the monomer and a certain amount of tetrabutylammonium bromide as a phase‐transfer catalyst. The solid phase consisted of potassium hydroxide particles with diameters smaller than 0.5 mm. The reaction was carried out at a low temperature of 0 °C and under nitrogen protection. No gelation was observed during the polymerization process, and the polymer was soluble in the usual organic solvents, such as chloroform, toluene, THF, and xylene. A polymer light‐emitting diode was fabricated with MEH‐PPV as an active luminescent layer. The device had an indium tin oxide/poly(3,4‐ethylenedioxylthiophene) (PEDOT)/MEH‐PPV/Ba/Al configuration. It showed a turn‐on voltage of 3.3 V, a luminescence intensity at 6.1 V of 550 cd/m², a luminescence efficiency of 0.43 cd/A, and a quantum efficiency of 0.57%. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3049–3054, 2004     

Crosslinkable poly(p‐phenylenevinylene) derivative

To simplify the fabrication of multilayer light‐emitting diodes, we prepared a p‐phenylenevinylene‐based polymer capped with crosslinkable styrene through a Wittig reaction. Insoluble poly(p‐phenylenevinylene) derivative (PPVD) films were prepared by a thermal treatment. The photoluminescence and ultraviolet–visible (UV–vis) absorbance of crosslinked films and noncrosslinked films were studied. We also studied the solvent resistance of crosslinked PPV films with UV–vis absorption spectra and atomic force microscopy. Double‐layer devices using crosslinked PPVD as an emitting layer, 2‐(4‐tert‐butylphenyl)‐5‐phenyl‐1,3,4‐oxadiazole (PBD) in poly(methyl methacrylate) as an electron‐transporting layer, and calcium as a cathode were fabricated. A maximum luminance efficiency of 0.70 cd/A and a maximum brightness of 740 cd/m² at 16 V were demonstrated. A 12‐fold improvement in the luminance efficiency with respect to that of single‐layer devices was realized. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2124–2129, 2004     

Poly(alkylthio‐p‐phenylenevinylene): Synthesis and electroluminescent and photovoltaic properties

Two alkylthio‐substituted poly(p‐phenylenevinylene) (AT–PPV) derivatives, poly(2‐octylthio‐p‐phenylenevinylene) (OT–PPV) and poly[5‐methoxy‐2‐(2′‐ethyl‐hexylthio)‐p‐phenylenevinylene] (MEHT–PPV), were synthesized by a Heck coupling reaction for the investigation of the effect of alkylthio groups on the optoelectronic properties of poly(p‐phenylenevinylene) derivatives. The absorption peaks of OT–PPV and MEHT–PPV solutions were located at 431 and 438 nm, respectively. As for solid films, an OT–PPV film showed an absorption maximum wavelength at 444 nm, 13 nm redshifted in comparison with its solution value, whereas an MEHT–PPV film displayed the same absorption peak position as its dilute solution; this indicated that there was no interchain interaction in the MEHT–PPV film. Polymeric light‐emitting diodes (PLEDs) and polymer solar cells (PSCs) based on OT–PPV and MEHT–PPV were fabricated and characterized. Very narrow bandwidths of the electroluminescence (EL) spectra of the two AT–PPVs were found, with the full width at half‐maximum of the emission being 40 and 47 nm for OT–PPV and MEHT–PPV, respectively. The maximum EL efficiency of the single‐layer PLED based on MEHT–PPV with Al as a cathode reached 1.49 cd/A. The PSC based on a blend of OT–PPV and [6,6]‐phenyl‐C₆₁ butyric acid methyl ester (PCBM) showed the power conversion efficiency of 1.4% under the illumination of AM1.5 (80 mW/cm²). © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1279–1290, 2006     

Synthesis and photovoltaic properties of poly(p‐phenylenevinylene) derivatives containing oxadiazole

A novel poly(p‐phenylenevinylene) PPV‐based copolymer (3C‐OXD‐PPV) with electron‐deficient oxadiazole segments as the side chain has been successfully synthesized through the Gilch polymerization. The obtained copolymer is soluble in common organic solvents such as chloroform, tetrahydronfuran, and 1,1,2,2‐tetrachloroethane. The copolymer was characterized by ¹H NMR, elemental analysis and GPC. TGA measurement of the copolymer shows it has good thermal stability with decomposition temperature higher than 350 °C. The absorption, electrochemical properties of the 3C‐OXD‐PPV were investigated and also compared with the properties of MEH‐PPV. The HOMO and LUMO levels of 3C‐OXD‐PPV were estimated from the electrochemical cyclic voltammograms. Bulk‐heterojunction PVCs were fabricated by using 3C‐OXD‐PPV blended PCBM as an active layer. The PCE of the PVC is 1.60% under 100 mW cm^?2 AM 1.5 illumination, which indicates that 3C‐OXD‐PPV is a potential candidate for the application of polymer PVC. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1003–1012, 2009     

Ellipsometry study of the photo‐oxidation of poly[(2‐methoxy‐5‐hexyloxy)‐ p‐phenylenevinylene]

Poly(p‐phenylenevinylene) (PPV) and its derivatives exhibit strong luminescence, being serious candidates to be used as active layers in organic light‐emitting diodes. However, the structural degradation caused by photo‐oxidation is an obstacle for commercial applications of such materials. Here, we show that spectroscopy ellipsometry is a useful technique to investigate the photo‐oxidation of poly[(2‐methoxy‐5‐hexyloxy)‐p‐phenylenevinylene] (MH‐PPV), a PPV derivative, which emits a red color light. Spectroscopy ellipsometry enables determination of the complex dielectric function—?*(E)—of MH‐PPV thin‐layer films exposed to air, in the 2.1–4.2 eV energy range, as a function of the light exposure time (t_e). By using the Lorentz model to fit the experimental ?*(E) curves, it was inferred that the interactions among polymeric chains increase with t_e. From ?*(E), it is also possible to obtain the complex refractive index, N*(E) = n + ik. At higher energies (where k ? n), n increases from 1.32 to 1.40 with the photo‐oxidation progress. The behavior of n was investigated by using the Lorenz–Lorentz equation, taking into account the contribution for n by the chromophores of MH‐PPV. The effect of photo‐oxidation, mainly due to the replacement of vinyl C?C by the ketone C?O bonds, is confirmed by Fourier transform infrared measurements, an effect that reduces the average effective polymer conjugation length. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1033–1041, 2004     

Synthesis and electrochemical and electroluminescent properties of N‐phenylcarbazole‐substituted poly(p‐phenylenevinylene)

An N‐phenylcarbazole‐containing poly(p‐phenylenevinylene) (PPV), poly[(2‐(4′‐carbazol‐9‐yl‐phenyl)‐5‐octyloxy‐1,4‐phenylenevinylene)‐alt‐(2‐(2′‐ethylhexyloxy)‐5‐methoxy‐1,4‐phenylenevinylene)] (Cz‐PPV), was synthesized, and its optical, electrochemical, and electroluminescent properties were studied. The molecular structures of the key intermediates, the carbazole‐containing boronic ester and the dialdehyde monomer, were crystallographically characterized. The polymer was soluble in common organic solvents and exhibited good thermal stability with a 5% weight loss at temperatures above 420 °C in nitrogen. A cyclic voltammogram showed the oxidation peak potentials of both the pendant carbazole group and the PPV main chain, indicating that the hole‐injection ability of the polymer would be improved by the introduction of the carbazole‐functional group. A single‐layer light‐emitting diode (LED) with a simple configuration of indium tin oxide (ITO)/Cz‐PPV (80 nm)/Ca/Al exhibited a bright yellow emission with a brightness of 1560 cd/m² at a bias of 11 V and a current density of 565 mA/cm². A double‐layer LED device with the configuration of ITO/poly(3,4‐ethylenedioxy‐2,5‐thiophene):poly (styrenesulfonic acid) (60 nm)/Cz‐PPV (80 nm)/Ca/Al gave a low turn‐on voltage at 3 V and a maximum brightness of 6600 cd/m² at a bias of 8 V. The maximum electroluminescent efficiency corresponding to the double‐layer device was 1.15 cd/A, 0.42 lm/W, and 0.5%. The desired electroluminescence results demonstrated that the incorporation of hole‐transporting functional groups into the PPVs was effective for enhancing the electroluminescent performance. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5765–5773, 2005     

Versatile route for tuning optical properties of poly(2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylenevinylene)

In this contribution, we report a versatile method for tuning optical properties of poly(2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylenevinylene) (MEH‐PPV) in its solution with 1,2‐dichloroethane, accomplished by reacting with pyridinium formate (PF), a volatile organic salt. We can systematically control the positions of absorption and photoluminescent (PL) spectra of MEH‐PPV by adjusting the concentration of PF in the solution. The addition of 10 vol % PF caused a blue‐shift in the absorption spectra by about 65 nm. When the concentration of PF decreased to 0.1 vol %, the blue‐shift occurred to a lesser extent, about 25 nm. The measurements of PL spectra showed similar behaviors. The λ_max shifted from 558 nm to 546 and 552 nm when 10 and 0.1 vol % of PF were added, respectively. The changes of PL colors from orange to yellow and green, respectively, were observed by naked eyes. Structural investigation by nuclear magnetic resonance and Fourier‐transformed infrared spectroscopy indicated that the changes of the optical properties were due to chemical modifications along the main chain and the side groups of MEH‐PPV. These results implied a simple route for engineering the HOMO–LUMO energy gap of MEH‐PPV, which could be utilized in advanced applications such as organic light‐emitting devices and solar cells. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 696–705, 2009     

Synthesis and characterization of naphthyl‐substituted poly(p‐phenylenevinylene)s with few structural defects for polymer light‐emitting diodes

A series of naphthyl‐substituted poly(p‐phenylenevinylene)s (2N‐PPV, 4N‐PPV, and NAP‐PPV) has been synthesized and characterized by Fourier transform IR, ¹H NMR, and elemental analysis. The polymers possess excellent solubility, high molecular weights, good thermal stability, and high photoluminescence efficiencies. Thermogravimetric analysis reveals the onset of degradation to be 347, 301, and 306 °C for 2N‐PPV, 4N‐PPV, and NAP‐PPV, respectively. The differential scanning calorimetry investigation gives the respective glass‐transition temperature values of 118, 135, and 141 °C. The UV and photoluminescence spectra measurements reveal that the polymers exhibit similar optical properties, indicating that side‐chain substitution has little effect on the optical properties of this series of polymers. Proton NMR measurement of the signal due to tolane–bisbenzyl defects at around 2.7 ppm indicates that all the polymers have negligible amounts of tolane–bisbenzyl defects along the polymer main chain as a result of the steric bulk imposed by the naphthalene side chain. The highest occupied and lowest unoccupied molecular orbital energy levels of the polymers are investigated through cyclic voltammetry. Polymer light‐emitting diodes utilizing the polymers as the emissive layer with a configuration of indium tin oxide/poly(3,4‐ethylenedioxythiophene)/polymer/Ba/Al are fabricated and evaluated. The diodes emit blue‐green to yellow‐green light with maximum peaks at 518, 542, and 486 nm for 2N‐PPV, 4N‐PPV, and NAP‐PPV, respectively. The respective turn‐on electric fields of the diodes are 0.84, 0.69, and 0.83 MV/cm and the respective maximum external quantum efficiencies are 0.08, 0.54, and 0.02%. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1647–1657, 2004     

Homologous series of alkylsilylphenyl‐substituted poly (p‐phenylenevinylene)s for light‐emitting diodes

Substituent‐induced electroluminescence polymers—poly[2‐(2‐dimethyldodecylsilylphenyl)‐1,4‐phenylenevinylene] [(o‐R₃Si)PhPPV], poly[2‐(3‐dimethyldodecylsilylphenyl)‐1,4‐phenylenevinylene] [(m‐R₃Si)PhPPV], and poly[2‐(4‐dimethyldodecylsilylphenyl)‐1,4‐phenylenevinylene] [(p‐R₃Si)PhPPV]—were synthesized according to the Gilch polymerization method. The band gap and spectroscopic data were tuned by the dimethyldodecylsilyl substituent being changed from the ortho position to the para position in the phenyl side group along the polymer backbone. The weight‐average molecular weights and polydispersities were 8.0–96 × 10⁴ and 3.0–3.4, respectively. The maximum photoluminescence wavelengths for (o‐R₃Si)PhPPV, (m‐R₃Si)PhPPV, and (p‐R₃Si)PhPPV appeared around 500–530 nm in the green emission region. Double‐layer light‐emitting diodes with an indium tin oxide/poly(3,4‐ethylenedioxythiophene)/polymer/Al configuration were fabricated with these polymers. The turn‐on voltages and the maximum brightness of (o‐R₃Si)PhPPV, (m‐R₃Si)PhPPV, and (p‐R₃Si)PhPPV were 6.5–8.7 V and 1986–5895 cd/m², respectively. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2347–2355, 2004     

Chain composition dependence of luminescence properties for copolymers of 2‐methoxy‐5‐2′‐ethyl‐hexyloxy‐1,4‐phenylenevinylene and 2,3‐diphenyl‐5‐octyl‐1,4‐phenylenevinylene

The copolymers of 2‐methoxy‐5‐2′‐ethyl‐hexyloxy‐1,4‐phenylenevinylene (MEH‐PV) and 2,3‐diphenyl‐5‐octyl‐1,4‐phenylenevinylene were prepared via the Gilch route with their chain compositions and the reactivity ratios of the monomers estimated by ¹H NMR spectroscopy. The results indicated that the copolymers tended to form an alternative copolymer as the feed ratio of the monomers closed to one‐half. When an individual copolymer solution in tetrahydrofuran was spun‐cast to form a film, the MEH‐PV units were able to attract the like units from the adjacent chains. As a result, the ultraviolet–visible absorption spectrum of the alternative copolymer in film form was broader than the spectra of those with different compositions. The photoluminescence spectra of the copolymers in film form exhibited the characteristic shoulder of poly(2‐methoxy‐5‐2′‐ethyl‐hexyloxy‐1,4‐phenylenevinylene), even though the content of MEH‐PV units was not great enough for the formation of repeat units in sequence. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2180–2186, 2003     

Intramolecular energy transferable (2,2‐diphenylvinyl)phenyl substituted poly(p‐phenylenevinylene) derivative with efficient photoluminescence and electroluminescence

A poly(p‐phenylenevinylene) (PPV) derivative containing a bulky (2,2‐diphenylvinyl)phenyl group in the side chain, EHDVP‐PPV, was synthesized by Gilch route. The reduced tolane‐bisbenzyl (TBB) defects, as well as the structure of the polymer, was confirmed by various spectroscopic methods. The intramolecular energy transfer from the (2,2‐diphenylvinyl)phenyl side group to the PPV backbone was studied by UV‐vis and photoluminescence (PL) of the obtained polymer and model compound. The polymer film showed maximum absorption and emission peaks at 454 and 546 nm, respectively, and high PL efficiency of 57%. A yellow electroluminescence (λ_max = 548 nm) was obtained with intensities of 6479 cd/m² when the light‐emitting diodes of ITO/PEDOT/EHDVP‐PPV/LiF/Al were fabricated. The maximum power efficiency of the devices was 0.729 lm/W with a turn‐on voltage of 3.6 V. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5636–5646, 2004     

Soluble,saturated‐red‐light‐emitting poly(p‐phenylenevinylene) containing triphenylamine units and cyano groups

A conjugated poly(p‐CN‐phenylenevinylene) (PCNPV) containing both electron‐donating triphenylamine units and electron‐withdrawing cyano groups was prepared via Knoevenagel condensation in a good yield. Gel permeation chromatography suggested that the soluble polymer had a very high weight‐average molecular weight of 309,000. A bright and saturated red emission was observed under UV excitation in solution and film. Cyclic voltammetry showed that the polymer presented quasi‐reversible oxidation with a relatively low potential because of the triphenylamine unit. A single‐layer indium tin oxide/PCNPV/Mg–Ag device emitted a bright red light (633 nm). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3947–3953, 2004     

Green‐emitting poly[(1,3‐phenylenevinylene)‐alt‐ (1,4‐phenylenevinylene)]s: Effect of the substitution patterns on the optical properties

Green‐emitting substituted poly[(2‐hexyloxy‐5‐methyl‐1,3‐phenylenevinylene)‐alt‐(2,5‐dihexyloxy‐1,4‐phenylenevinylene)]s ( 6 ) were synthesized via the Wittig–Horner reaction. The polymers were yellow resins with molecular weights of 10,600. The ultraviolet–visible (UV–vis) absorption of 6 (λ_max = 332 or 415 nm) was about 30 nm redshifted from that of poly[(2‐hexyloxy‐5‐methyl‐1,3‐phenylenevinylene)‐alt‐(1,4‐phenylenevinylene)] ( 2 ) but was only 5 nm redshifted with respect to that of poly[(1,3‐phenylenevinylene)‐alt‐(2,5‐dihexyloxy‐1,4‐phenylenevinylene)] ( 1 ). A comparison of the optical properties of 1 , 2 , and 6 showed that substitution on m‐ or p‐phenylene could slightly affect their energy gap and luminescence efficiency, thereby fine‐tuning the optical properties of the poly[(m‐phenylene vinylene)‐alt‐(p‐phenylene vinylene)] materials. The vibronic structures were assigned with the aid of low‐temperature UV–vis and fluorescence spectroscopy. Light‐emitting‐diode devices with 6 produced a green electroluminescence output (emission λ_max ～ 533 nm) with an external quantum efficiency of 0.32%. Substitution at m‐phenylene appeared to be effective in perturbing the charge‐injection process in LED devices. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1820–1829, 2004     

Novel saturated red‐emitting poly(p‐phenylenevinylene) copolymers with narrow‐band‐gap units of 2,1,3‐benzothiadiazole synthesized by a palladium‐catalyzed Stille coupling reaction

Novel poly(p‐phenylenevinylene) (PPV) copolymers derived from 1‐methoxy‐4‐octyloxyphenylene (MOP), 2,1,3‐benzothiadiazole (BT), and trans‐1,2‐bis(tributylstannyl)ethylene were first prepared by a palladium‐catalyzed Stille coupling reaction. The feed ratios of MOP to BT were 99.5:0.5, 99:1, 95:5, 85:15, 70:30, and 50:50. An efficient energy transfer from the 2‐methoxy‐5‐octyloxy‐p‐phenylenevinylene segment to the narrow‐band‐gap units was observed. The poly(2‐methoxy‐5‐octyloxy‐p‐phenylenevinylene‐2,1,3‐benzothiadiazolevinylene) copolymers emitted deep red light. The maximum electroluminescence emission of these PPV copolymers occurred at 659–724 nm and was accompanied by gradual redshifting with an increasing BT concentration. The photophysical properties were examined in comparison with those of copolymers based on BT and fluorene or N‐alkylcarbazole doped with the same BT concentration in the copolymer main chain. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2325‐2336, 2005     

Control of molecular aggregation in symmetrically substituted π‐conjugated bulky poly(p‐phenylenevinylene)s and their copolymers

A new series of symmetrically substituted bulky PPV‐copolymers based on poly(bis‐2,5‐(2‐ethylhexyloxy)‐1,4‐phenylenevinylene) ( BEH‐PPV ) bearing tricyclodecane (TCD) pendants were synthesized to study the effect of chain aggregation in the π‐conjugated polymer backbone. The composition of the copolymers was varied up to 100 mol % and the structures of the copolymer were confirmed by NMR and FTIR. The molecular weights of the copolymers were obtained as M_w = 11,500–1,78,800 depending on the TCD‐incorporation in BEH‐PPV. The origin of the π‐aggregation was investigated using mixture of solvents (polar or nonpolar) or temperature as external stimuli. Absorption, photoluminescence, and time‐resolved fluorescence decay techniques were employed as tools to trace molecular aggregation in solution and solid state. The TCD‐substituted bulky copolymers showed almost twice the enhancement in photoluminescence compared with that of BEH‐PPV . Solvent‐induced aggregation studies of copolymers revealed the existence of strong molecular aggregation in BEH‐PPV compared with that of bulky copolymers. Variable temperature studies further evidence for the reversibility of molecular aggregation on heating/cooling cycles and showed isosbetic points with respect to free and aggregated polymer chains. Time‐resolved fluorescent studies confirmed the existence of free and aggregated π‐conjugated species with a life time of 0.1 to 1.0 ns. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2631–2646, 2009     

Syntheses and electroluminescence properties of conjugated poly(p‐phenylene vinylene) derivatives bearing dendritic pendants

A series of new poly(p‐phenylene vinylene) derivatives with different dendritic pendants—poly{2‐[3′,5′‐bis(2″‐ethylhexyloxy)benzyloxy]‐1,4‐phenylenevinylene} (BE–PPV), poly{2‐[3′,5′‐bis(3″,7″‐dimethyl)octyloxy]‐1,4‐phenylenevinylene} (BD–PPV), poly(2‐{3′,5′‐bis[3″,5″‐bis(2?‐ethylhexyloxy)benzyloxy]benzyloxy}‐1,4‐phenylenevinylene) (BBE–PPV), poly(2‐{3′,5′‐bis[3″,5″‐bis(3?,7?‐dimethyloctyloxy)benzyloxy]benzyloxy}‐1,4‐phenylenevinylene) (BBD–PPV), and poly[(2‐{3′,5′‐bis[3″,5″‐bis(2?‐ethylhexyloxy)benzyloxy]benzyloxy}‐1,4‐phenylenevinylene)‐co‐(2‐{3′,5′‐bis[3″,5″‐bis(3?,7?‐dimethyloctyloxy)benzyloxy]benzyloxy}‐1,4‐phenylenevinylene)] (BBE‐co‐BBD–PPV; 1:1)—were successfully synthesized according to the Gilch route. The structures and properties of the monomers and the resulting conjugated polymers were characterized with ¹H and ¹³C NMR, elemental analysis, gel permeation chromatography, thermogravimetric analysis, ultraviolet–visible absorption spectroscopy, photoluminescence, and electroluminescence spectroscopy. The obtained polymers possessed excellent solubility in common solvents and good thermal stability, with a 5% weight loss temperature of more than 328 °C. The weight‐average molecular weights and polydispersity indices of BE–PPV, BD–PPV, BBE–PPV, BBD–PPV, and BBE‐co‐BBD–PPV (1:1) were in the range of 1.33–2.28 × 10⁵ and 1.35–1.53, respectively. Double‐layer light‐emitting diodes (LEDs) with the configuration of indium tin oxide/polymer/tris(8‐hydroxyquinoline) aluminum/Mg:Ag/Ag devices were fabricated, and they emitted green‐yellow light. The turn‐on voltages of BE–PPV, BD–PPV, BBE–PPV, BBD–PPV, and BBE‐co‐BBD–PPV (1:1) were approximately 5.6, 5.9, 5.5, 5.2, and 4.8 V, respectively. The LED devices of BE–PPV and BD–PPV possessed the highest electroluminescent performance; they exhibited maximum luminance with about 860 cd/m² at 12.8 V and 651 cd/m² at 13 V, respectively. The maximum luminescence efficiency of BE–PPV and BD–PPV was in the range of 0.37–0.40 cd/A. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3126–3140, 2005     

Synthesis and chiroptical properties of poly (p‐phenylenevinylene‐alt‐m‐phenylenevinylene) bearing (−)‐trans‐myrtanoxyl groups on the p‐phenylene rings

Chiral poly(p‐phenylenevinylene‐alt‐m‐phenylenevinylene)s bearing (?)‐trans‐myrtanoxyl groups on the p‐phenylene rings were synthesized by Wittig's reaction and Heck's reaction, respectively, namely Myr‐PMPV‐w and Myr‐PMPV‐h correspondingly. The chiroptical properties of the polymers were investigated in chlorobenzene solution by circular dichroism. The results showed that both Myr‐PMPV‐w and Myr‐PMPV‐h showed no Cotton effect due to their irregular molecular structure. By the treatment with I₂, most of the cis‐vinylene linkages in Myr‐PMPV‐w were converted to trans‐vinylenes, consequently, the structure of Myr‐PMPV‐w became much more regular, and the resulting polymer ( iso‐Myr‐PMPV‐w ) showed strong bisignate Cotton effects in the π–π* transition. Compared to its analogous poly(p‐phenylenevinylene) (PPV) ( iso‐Myr‐PPV‐w ), iso‐Myr‐PMPV‐w showed much stronger Cotton effect, its maximum g value was about one order of magnitude higher than that of iso‐Myr‐PPV‐w under the same conditions. With increasing concentration and decreasing temperature, the g_max value of iso‐Myr‐PMPV‐w increased, and the maximum absorption was slightly blue‐shifted, but the shape and range of absorption curves did not changed significantly, and no clear isosbestic point could be observed. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3336–3343, 2008     

Synthesis and optoelectronic properties of luminescent poly(p‐phenylenevinylene) derivatives containing electron‐transporting 1,3,4‐oxadiazole groups

Three random copolymers ( P1–P3 ) comprising phenylenevinylene and electron‐transporting aromatic 1,3,4‐oxadiazole segments (11, 18, 28 mol %, respectively) were prepared by Gilch polymerization to investigate the influence of oxadiazole content on their photophysical, electrochemical, and electroluminescent properties. For comparative study, homopolymer poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐p‐phenylenevinylene] ( P0 ) was also prepared by the same process. The polymers ( P0–P3 ) are soluble in common organic solvents and thermally stable up to 410 °C under a nitrogen atmosphere. Their optical properties were investigated by absorption and photoluminescence spectroscopy. The optical results reveal that the aromatic 1,3,4‐oxadiazole chromophores in P1–P3 suppress the intermolecular interactions. The HOMO and LUMO levels of these polymers were estimated from their cyclic voltammograms. The HOMO levels of P0–P3 are very similar (?5.02 to ?5.03 eV), whereas their LUMO levels decrease readily with increasing oxadiazole content (?2.7, ?3.08, ?3.11, and ?3.19 eV, respectively). Therefore, the electron affinity of the poly(p‐phenylenevinylene) chain can be gradually enhanced by incorporating 1,3,4‐oxadiazole segments. Among the polymers, P1 (11 mol % 1,3,4‐oxadiazole) shows the best EL performance (maximal luminance: 3490 cd/m², maximal current efficiency: 0.1 cd/A). Further increase in oxadiazole content results in micro‐phase separation that leads to performance deterioration. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4377–4388, 2007     

Comparative study of the optical,electrochemical, electrolumiscent,and photovoltaic properties of dendritic pendants modified poly(p‐phenylene vinylene)s

In this study, the optical, electrochemical, electrolumiscent, and photovoltaic properties of a series of poly(p‐phenylene vinylene) (PPV) derivatives bearing different dendritic pendants, poly{2‐[3′,5′‐bis(2″‐ethylhexyloxy)benzyloxy]‐1,4‐phenylenevinylene} (BE‐PPV), poly{2‐[2′,5′‐bis(3″,7″‐dimethyl)octyloxy]‐1,4‐phenylenevinylene} (BD‐PPV), poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylenevinylene] (MEH‐PPV), poly{2‐[3′,5′‐bis(2″‐ethylhexyloxy)benzyloxy]‐1,4‐phenylenevinylene}‐co‐poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylenevinylene] (BE‐co‐MEH‐PPV), and poly{2‐[2′,5′‐bis(3″,7″‐dimethyl)octyloxy]‐1,4‐phenylenevinylene}‐co‐poly[2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐1,4‐phenylenevinylene] (BD‐co‐MDMO‐PPV), were investigated. The steric pendants strongly affect the absorption spectra, photoluminescence (PL) sepctra, the onset oxidation/reduction potentials, and further affect the electrolumiscent and photovoltaic properties. Copolymerization can reduce the steric effect and improve the electrolumiscent and photovoltaic properties. The brightness of light‐emitting diodes base on copolymer BE‐co‐MEH‐PPV and BD‐co‐MDMO‐PPV reached 3988 and 3864 cd/m², respectively, much higher than that based on homopolymer BE‐PPV (523 cd/m²) and BD‐PPV (333 cd/m²), also higher than that based on MEH‐PPV (3788 cd/m²). The power conversion efficiency (PCE) of solar cells based on BE‐co‐MEH‐PPV and BD‐co‐MDMO‐PPV reached 1.41, 0.76%, respectively, much higher than that based on BE‐PPV (0.24%) and BD‐PPV (0.14%). Copyright © 2010 John Wiley & Sons, Ltd.     

Conformation and luminescence characteristics of nanopoly[2‐metoxy‐5‐(2′‐ethyl‐hexyloxy)‐p‐phenylene vinylene] in two‐dimensional arrays

With anodic alumina with an ordered nanopore array used as a template, poly[2‐metoxy‐5‐(2′‐ethyl‐hexyloxy)‐p‐phenylene vinylene] (MEH–PPV) was embedded into the nanopores, and then two‐dimensional arrays of light‐emitting nanopolymers were prepared. By the measurement and analysis of photoluminescence and photoluminescence excitation spectra of the samples, it was demonstrated that the optical properties of the nano‐MEH–PPV arrays were obviously different from those of MEH–PPV films. The conformations of the MEH–PPV chains in the nanopores, films, and solutions and their effects on the optical properties were examined. It was determined experimentally that the conformations of the MEH–PPV chains in the solutions were maintained in the nano‐MEH–PPV arrays. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3037–3041, 2006