Synthesis,characterization, and degradation of poly(ethylene‐b‐ε‐caprolactone) diblock copolymer

Poly(ethylene‐b‐ε‐caprolactone) (PE‐b‐PCL) diblock copolymers were synthesized by ring‐opening polymerization (ROP) of ε‐caprolactone (CL) with α‐hydroxyl‐ω‐methyl polyethylene (PE‐OH) as a macroinitiator and ammonium decamolybdate (NH₄)₈[Mo₁₀O₃₄] as a catalyst. Polymerization was conducted in bulk (130–150°C) with high yield (87–97%). Block copolymers with different compositions were obtained and characterized by ¹H and ¹³C NMR, MALDI‐TOF, SAXS, and DSC. End‐group analysis by NMR and MALDI‐TOF indicates the formation of α‐hydroxyl‐ω‐methyl PE‐b‐PCL. The PE‐b‐PCL degradation was studied using thermogravimetric analysis (TGA) and alkaline hydrolysis. The PCL block was hydrolyzed by NaOH (4M), without any effect on the PE segment. Copyright © 2009 John Wiley & Sons, Ltd.     

The influence of hard‐segments on two‐phase structure and shape memory properties of PCL‐based segmented polyurethanes

Poly(ε‐caprolactone)‐based segmented polyurethanes (PCLUs) were prepared from poly(ε‐caprolactone) diol, diisocyanates (DI), and 1,4‐butanediol. The DIs used were 4,4′‐diphenylmethane diisocyanate (MDI), 2,4‐toluenediisocyanate (TDI), isophorone diisocyanate (IPDI), and hexamethylene diisocyanate (HDI). Differential scanning calorimetry, small‐angle X‐ray scattering, and dynamic mechanical analysis were employed to characterize the two‐phase structures of all PCLUs. It was found that HDI‐ and MDI‐based PCLUs had higher degree of microphase separation than did IPDI‐ and TDI‐based PCLUs, which was primarily due to the crystallization of HDI‐ and MDI‐based hard‐segments. As a result, the HDI‐based PCLU exhibited the highest recovery force up to 6 MPa and slowest stress relaxation with increasing temperature. Besides, it was found that the partial damage in hard‐segment domains during the sample deformation was responsible for the incomplete shape‐recovery of PCLUs after the first deformation, but the damage did not develop during the subsequent deformation. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 557–570, 2007     

Molecular composites composed of castor oil‐modified poly(ε‐caprolactone) and self‐assembled hydroxystearic acid fibers

After (R)‐12‐hydroxystearic acid (HSA) was mixed at 100 °C with the castor oil‐modified poly(ε‐caprolactone) (CO‐PCL) prepared by the ring‐opening polymerization of ε‐caprolactone in the presence of castor oil, the mixture was gradually cooled to room temperature to give a solidified CO‐PCL/HSA composite. The CO‐PCL/HSA sample showed an exothermic peak at around 67–71 °C which was lower than the melting point of HSA (76.8 °C), indicating the formation of mesogenic HSA aggregates. The rheological measurement of the CO‐PCL/HSA revealed the formation of HSA organogel at around 67–55 °C during the cooling process from the melt. Furthermore, the polarized and normal optical microscopic analyses of CO‐PCL/HSA on the cooling stage revealed that anisotropic fibrous materials are formed at around 60 °C and then the fibrous network propagated over the matrix polymer. The flexural modulus and storage modulus of the CO‐PCL/HSA composite increased with increasing HSA content. The CO‐PCL/HSA composite annealed at 60 °C for 2 h on the cooling process had a higher flexural and storage modulus than the sample without annealing. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1281–1289, 2010     

Rheological behavior of biocomposites of silk fibroin fiber and poly(ε‐caprolactone): Effect of fiber network

Rheological behavior was examined for biocomposites of rod‐like silk fibroin (SF) fiber and poly(ε‐caprolactone) (PCL) to investigate an effect(s) of the SF fiber network therein on the mechanical properties. At 160 °C where PCL was a homogeneous melt, linear viscoelastic tests revealed that the SF/PCL composites hardly relax to behave essentially as elastic solids (more precisely, plastic solids before yielding) at low frequencies. The corresponding equilibrium modulus G₀ increased strongly with the SF volume fraction ?_SF (G₀ ～ ?) and was attributable to the elastic bending of the SF fibers incorporated in the network. The Doi‐Kuzuu model for non‐Brownian rods was modified for the SF/PCL composites by incorporating the rod–rod contact at equilibrium. The G₀ calculated from this model was satisfactorily close to the data, in both ?_SF dependence and magnitude, lending support to the assignment of the composite elasticity to the fiber bending. The storage modulus G′ measured under large‐amplitude oscillatory shear (LAOS) was smaller than the linear viscoelastic G′, and this difference between the linear and nonlinear moduli was enhanced for the composites with a larger SF content and at lower frequencies. This nonlinear effect was attributable to a decrease of the effective fiber–fiber contacts sustaining the elasticity under LAOS. Under steady shear, the SF/PCL composites exhibited nonlinear (plastic) flow behavior associated with the stress overshoot, and their apparent viscosity was comparable to/lower than the viscosity of neat PCL matrix. The overshoot became much less significant on application of a second shear immediately after the first shear, while the overshoot was partly recovered after a quiescent rest between the first and second shears. These nonlinear features were attributable to slippage between shear‐oriented fibers and PCL matrix. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1957–1970, 2009     

Zinc(II) complexes of Triaza and Amidinate ligands: Efficient initiators for the ring‐opening polymerization of ε‐Caprolactone and rac‐Lactide

Zinc complexes supported by tertiary 1,3,5‐triazapenta‐1,3‐dienate ligand (L¹) and N ‐benzoyl‐N′ ‐arylbenzamidinate [aryl =2,6‐diisopropylphenyl (L²), phenyl (L³)] ligands have been synthesized and characterized. The reaction of L¹H with ZnEt₂ affords a mononuclear zinc complex [L¹ZnEt] ( 1 ) in good yield. Tetra nuclear zinc complex [(L¹)₂Zn₄O(OAc)₄] ( 2 ) is prepared by treating L¹H with one equivalent of Zn(OAc)₂ in toluene. Further, dinuclear zinc complexes [L²ZnEt]₂ ( 3 ) and [L³ZnEt]₂ ( 4 ) are obtained in good yields from L²H and L³H with ZnEt₂ in toluene respectively_. The complexes 1–4 have been characterized by ¹H/¹³C NMR spectroscopy and single crystal X‐ray diffraction studies. All of the complexes have been explored for their catalytic activity toward the ring‐opening polymerization (ROP) of ε ‐caprolactone. It has been found that complex 1 is an active catalyst for the polymerization of ε ‐caprolactone in presence of a cocatalyst benzyl alcohol (BnOH). While complex 2 is as active as 1 there is no need for a cocatalyst for the polymerization to proceed. Dinuclear zinc complexes 3 and 4 show very high activity for the ROP of ε ‐caprolactone (CL) and rac ‐lactide (LA) without requiring a cocatalyst. The resultant polymers are found to have very high molecular weight (M _n = 296 X 10³ g mol⁻¹) and relatively narrow polydispersity index compared to 1 and 2 .     

Syntheses of trimethoxysilyl‐endcapped polylactones via 3‐mercaptopropyl trimethoxysilane

Monofunctional polylactones were prepared by Bu₂Sn(OMe)₂‐initiated ring‐opening polymerization of ε‐caprolactone (εCL) followed by acylation with bromoacetylbromide. Telechelic polylactones and polylactides were prepared via ring‐expansion polymerization with 2,2‐dibutyl‐2‐stanna‐1,3‐dioxepane (DSDOP) or 2,2‐dibutyl‐2‐stanna‐pentaoxacyclotridecane (Bu₂SnTEG) as cyclic initiator. In situ combination of the polymerization with condensation by means of bromoacetylbromide yielded polylactones having bromoacetate endgroups. These endgroups were subjected to nucleophilic substitution with 3‐mercaptopropyl trimethoxysilane (3‐MPTMS). Analogous experiments were conducted with dl‐lactide. The telechelic trimethoxysilyl‐endcapped polylactones were characterized by viscosity, ¹H and ¹³C NMR‐spectroscopy, and MALDI‐TOF mass spectrometry. The mass spectra revealed small amounts of cyclic oligolactones as byproducts in all samples. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3667–3674, 2005     

Thermoplastic elastomers based on poly(l‐Lysine)‐Poly(ε‐Caprolactone) multi‐block copolymers

Novel thermoplastic elastomers based on multi‐block copolymers of poly(l ‐lysine) (PLL), poly(N‐ε‐carbobenzyloxyl‐l ‐lysine) (PZLL), poly(ε‐caprolactone) (PCL), and poly(ethylene glycol) (PEG) were synthesized by combination of ring‐opening polymerization (ROP) and chain extension via l ‐lysine diisocyanate (LDI). SEC and ¹H NMR were used to characterize the multi‐block copolymers, with number‐average molecular weights between 38,900 and 73,400 g/mol. Multi‐block copolymers were proved to be good thermoplastic elastomers with Young's modulus between 5 and 60 MPa and tensile strain up to 1300%. The PLL‐containing multi‐block copolymers were electrospun into non‐woven mats that exhibited high surface hydrophilicity and wettability. The polypeptide–polyester materials were biocompatible, bio‐based and environment‐friendly for promising wide applications. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3012–3018     

Toughening modification of PLLA with PCL in the presence of PCL‐b‐PLLA diblock copolymers as compatibilizer

To obtain an effective compatibilizer for the blends of poly(L‐lactide) (PLLA) and poly(ε‐caprolactone) (PCL), the diblock copolymers PCL‐b‐PLLA with different ratios of PCL/PLLA (CL/LA) and different molecular weights (M_n) were synthesized by ring‐opening polymerization (ROP) of L‐lactide with monohydric poly(ε‐caprolactone) (PCL‐OH) as a macro‐initiator. These copolymers were melt blended with PLLA/PCL (80/20) blend at contents between 3.0 and 20 phr (parts per hundred resin), and the effects of added PCL‐b‐PLLA on the mechanical, morphological, rheological, and thermodynamic properties of the PLLA/PCL/PCL‐b‐PLLA blends were investigated. The compatibility between PLLA matrix and PCL phase was enhanced with decreasing in CL/LA ratios or increasing in M_n for the added PCL‐b‐PLLA. Moreover, the crystallinity of PLLA matrix increased because of the added compatibilizers. The PCL‐b‐PLLA with the ratio of CL/LA (50/50) and M_n ≥ 39.0 kg/mol were effective compatibilizers for PLLA/PCL blends. When the content of PCL‐b‐PLLA is greater than or equal to 5 phr, the elongations at break of the PLLA/PCL/PCL‐b‐PLLA blends all reached approximately 180%, about 25 times more than the pristine PLLA/PCL(80/20) blend.     

Real‐time SAXS and WAXS study of the multiple melting behavior of poly(ε‐caprolactone)

The multiple melting behavior of poly(ε‐caprolactone) (PCL) was investigated by real‐time small angle X‐ray scattering (SAXS) and wide angle X‐ray scattering (WAXS) measurements coupling with differential scanning calorimetry (DSC). Semicrystalline specimens prepared by a continuous cooling process showed lengthening of the Bragg period during the progress of double melting. A model of variable thickness of lamella was proposed to fit to the SAXS patterns and revealed that both the crystalline lamella and the amorphous layer contributed to the increase in Bragg period while the later dominated the contribution. The model of variable thickness although satisfied the SAXS data was unable to compromise the data from other probing tools. A modification of the model proposed that each lamella piling up to construct the stacks in the crystallites was itself nonuniform in thickness. The modification with the parallel occurrence of the mechanism of surface melting and crystallization successfully compromised the observations from SAXS, DSC, and optical microscopy and provided a new perspective for the explanation to lengthening of the Bragg period related to multiple melting behavior. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1777–1785, 2010     

Shape Memory Properties and Enzymatic Degradability of Poly(ε‐caprolactone)‐Based Polyurethane Urea Containing Phenylalanine‐Derived Chain Extender

Biodegradable shape memory polymers are promising biomaterials for minimally invasive surgical procedures. Herein, a series of linear biodegradable shape memory poly(ε‐caprolactone) (PCL)‐based polyurethane ureas (PUUs) containing a novel phenylalanine‐derived chain extender is synthesized. The phenylalanine‐derived chain extender, phenylalanine‐hexamethylenediamine‐phenylalanine (PHP), contains two chymotrypsin cleaving sites to enhance the enzymatic degradation of PUUs. The degradation rate, the crystallinity, and mechanical properties of PUUs are tailored by the content of PHP. Meanwhile, semicrystalline PCL is not only hydrolytically degradable but also vital for shape memory. Good shape memory ability under body temperature is achieved for PUUs due to the strong interactions in hard segments for permanent crosslinking and the crystallization‐melt transition of PCL to switch temporary shape. The PUUs would have a great potential in application as implanting stent.     

Poly(ε‐caprolactone)–poly(isobutylene): A crystallizing,hydrogen‐bonded pseudo‐block copolymer

The crystallization of block copolymers (BCPs) under homogeneous and heterogeneous nucleation is currently well understood revealing the strong interplay of crystallization in competition to microphase separation. This article reports investigations on synthesis and crystallization processes in weakly interacting supramolecular pseudo‐BCPs, composed of poly(ε‐caprolactone) (PCL) and poly(isobutylene) (PIB) blocks, connected by a specifically interacting hydrogen bond (thymine/2,6‐diaminotriazine). Starting from ring opening polymerization of ε‐caprolactone, the use of “click”‐chemistry enabled the introduction of thymine endgroups onto PCL polymer, thus generating the fully thymine‐substituted pure PCLs ( 1a , 1b ) as judged via NMR and MALDI analysis. Physical mixing of 1a , 1b with a bivalent, bis(2,6‐diaminotriazine)‐containing molecule ( 2 ) generated the bivalent polymers BC1 and BC2 , whereas mixing of 1a or 1b with the 2,6‐diaminotriazine‐substituted PIB ( 3 ) generated the supramolecular pseudo‐BCPs BC3 and BC4 . Thermal investigations (DSC, Avrami analysis) revealed only minor changes in the crystallization behavior of BC1 – BC4 with Avrami exponents close to three, indicative of a confluence of the growing crystals during the crystallization process. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and characterization of tercopolymers derived from ε‐caprolactone,trimethylene carbonate,and lactide

A series of tri‐components copolymers with different molar ratios were synthesized via bulk ring‐opening copolymerization of trimethylene carbonate (TMC), L ‐lactide (LLA), and ε‐caprolactone (ε‐CL), using stannous octoate as catalyst. The sequence structure of the tercopolymer chain was characterized by ¹H and ¹³C nuclear magnetic resonance (NMR), Fourier transform infrared (FTIR), and gel permeation chromatography (GPC). The results showed that although block sequence of the corresponding monomers still existed in the tercopolymer chain, the random tercopolymers were ultimately obtained due to the transesterification during polymerization. For the samples TP1 and TP2, longer sequence of LLA existed in the molecular chains. The thermal properties of tercopolymers were investigated by differential scanning calorimetry (DSC) and the mechanical properties of the resulting copolymers were studied by using a tensile tester. The results indicated that the properties of these copolymers could be adjusted by changing the compositions of the copolymers. The resulting tercopolymers are expected to have potential uses as nerve regeneration and other biomedicine materials. Copyright © 2007 John Wiley & Sons, Ltd.     

Physical Properties and Erosion Behavior of Poly(trimethylene carbonate‐co‐ε‐caprolactone) Networks

Form‐stable resorbable networks are prepared by gamma irradiating trimethylene carbonate (TMC)‐ and ε‐caprolactone (CL)‐based (co)polymer films. To evaluate their suitability for biomedical applications, their physical properties and erosion behavior are investigated. Homopolymer and copolymer networks that are amorphous at room temperature are flexible and rubbery with elastic moduli ranging from 1.8 ± 0.3 to 5.2 ± 0.4 MPa and permanent set values as low as 0.9% strain. The elastic moduli of the semicrystalline networks are higher and range from 61 ± 3 to 484 ± 34 MPa. The erosion behavior of (co)polymer networks is investigated in vitro using macrophage cultures, and in vivo by subcutaneous implantation in rats. In macrophage cultures, as well as upon implantation, a surface erosion process is observed for the amorphous (co)polymer networks, while an abrupt decrease in the rate and a change in the nature of the erosion process are observed with increasing crystallinity. These resorbable and form‐stable networks with tuneable properties may find application in a broad range of biomedical applications.

     

Fabrication of Compositional‐Gradient Biodegradable Polymeric Films Showing Self‐Bending Deformation

A compositional graded film of poly(ε‐caprolactone) (PCL) with 4,4′‐thiodiphenol (TDP), in the film thickness direction, was fabricated by self‐diffusing of TDP in the PCL melt. We found out the self‐bending deformation of the gradient film, which bent into a rolled‐up shape by itself. The initial shape of the film was flat when the sample was quenched from the melt. Upon the fast crystallization of PCL, the gradient film bent to the side with low TDP content. Then, after PCL crystallized the film bent to the opposite direction, that is, to the side with high TDP content. This bending to the TDP rich region was induced by not only the crystallization of PCL but also mass transfer due to the diffusion of TDP from TDP rich region to poor region.

     

Electrospun Poly(ε‐caprolactone)/Polyhedral Oligomeric Silsesquioxane‐Based Copolymer Blends: Evolution of Fiber Internal Structures

This study reports the structural transition of electrospun poly(ε‐caprolactone) (PCL)/poly[(propylmethacryl‐heptaisobutyl‐polyhedral oligomeric silsesquioxane)‐co‐(methyl meth­acrylate)] (POSS‐MMA) blends, from PCL‐rich fibers, to bicontinuous PCL core/POSS‐MMA shell fibers, to POSS‐MMA‐rich fibers with a discontinuous PCL inner phase. A ternary phase diagram depicting the electrospinnability of PCL/POSS‐MMA solutions is constructed by evaluating the morphological features of fibers electrospun from solutions with various concentrations and PCL/POSS‐MMA blend ratios. X‐ray diffraction, Raman spectroscopy, and differential scanning calorimetry are further used to characterize the electrospun PCL/POSS‐MMA hybrid fibers. These physicochemical characterization results are thoroughly discussed to understand the internal structures of the hybrid fibers, which are directly correlated to the phase separation behavior of the electrospun solutions. The current study provides further insight into the complex phase behavior of POSS‐copolymer‐based systems, which hold great potential for a broad spectrum of biomedical applications.

     

Synthesis and Characterization of Star‐Shaped Diblock Poly(ε‐caprolactone)/Poly(ethylene oxide) Copolymers

Summary: Star‐shaped hydroxy‐terminated poly(ε‐caprolactone)s (ssPCL), with arms of different lengths, were obtained by ring‐opening polymerization (ROP) of ε‐caprolactone initiated by pentaerythritol, and were condensed with α‐methyl‐ω‐(3‐carboxypropionyloxy)‐poly(ethylene oxide)s ( = 550–5 000) to afford four‐armed PCL‐PEO star diblock copolymers (ssPCL‐PEO). The polymers were characterized by ¹H and ¹³C NMR spectroscopy and size‐exclusion chromatography (SEC). The melting behavior of ssPCLs was studied by differential scanning calorimetry (DSC). X‐ray diffraction and DSC techniques were used to investigate the crystalline phases of ssPCL‐PEOs.

The part of the synthesis of four‐armed star‐shaped diblock poly(ε‐caprolactone)‐poly(ethylene oxide) copolymers as described.     

Viscoelastic properties of poly(ε‐caprolactone) – hydroxyapatite micro‐ and nano‐composites

Various composites have been proposed in the literature for the fabrication of bioscaffolds for bone tissue engineering. These materials include poly(ε‐caprolactone) (PCL) with hydroxyapatite (HA). Since the biomaterial acts as the medium that transfers mechanical signals from the body to the cells, the fundamental properties of the biomaterials should be characterized. Furthermore, in order to control the processing of these materials into scaffolds, the characterization of the fundamental properties is also necessary. In this study, the physical, thermal, mechanical, and viscoelastic properties of the PCL‐HA micro‐ and nano‐composites were characterized. Although the addition of filler particles increased the compressive modulus by up to 450%, the thermal and viscoelastic properties were unaffected. Furthermore, although the presence of water plasticized the polymer, the viscoelastic behavior was only minimally affected. Testing the composites under various conditions showed that the addition of HA can strengthen PCL without changing its viscoelastic response. The results found in this study can be used to further understand and approximate the time‐dependent behavior of scaffolds for bone tissue engineering. Copyright © 2012 John Wiley & Sons, Ltd.     

Synthesis and properties of photocurable biodegradable multiblock copolymers based on poly(ε‐caprolactone) and poly(L‐lactide) segments

Photocurable biodegradable multiblock copolymers were synthesized from poly(ε‐caprolactone) (PCL) diol and poly(L ‐lactide) (PLLA) diol with 4,4′‐(adipoyldioxy)dicinnamic acid (CAC) dichloride as a chain extender derived from adipoyl chloride and 4‐hydroxycinnamic acid, and they were characterized with Fourier transform infrared and ¹H NMR spectroscopy, gel permeation chromatography, wide‐angle X‐ray diffraction, differential scanning calorimetry, and tensile tests. The copolymers were irradiated with a 400‐W high‐pressure mercury lamp from 30 min to 3 h to form a network structure in the absence of photoinitiators. The gel concentration increased with time, and a concentration of approximately 90% was obtained in 90–180 min for all the films. The photocuring hardly affected the crystallinity and melting temperature of the PCL segments but reduced the crystallinity of the PLLA segments. The mechanical properties, such as the tensile strength, modulus, and elongation, were significantly affected by the copolymer compositions and gel concentrations. Shape‐memory properties were determined with cyclic thermomechanical experiments. The CAC/PCL and CAC/PCL/PLLA (75/25) films photocured for 30–120 min showed good shape‐memory properties with strain fixity rates and recovery rates of approximately 100%. The formation of the network structure and the crystallization and melting of the PCL segments played very important roles for the typical shape‐memory properties. Finally, the degradation characteristics of these copolymers were investigated in a phosphate buffer solution at 37 °C with proteinase‐k and Pseudomonas cepacia lipase. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2426–2439, 2005     

d‐Fructose Modification Enhanced Internalization of Mixed Micelles in Breast Cancer Cells via GLUT5 Transporters

d ‐Fructose modified poly(ε‐caprolactone)‐polyethylene glycol (PCL‐PEG‐Fru) diblock amphiphile is synthesized via Cu(I)‐catalyzed click chemistry, which self‐assembles with D‐α‐tocopheryl polyethylene glycol 1000 succinate (TPGS) into PCL‐PEG‐Fru/TPGS mixed micelles (PPF MM). It has been proven that glucose transporter (GLUT)5 is overexpressed in MCF‐7 cells other than L929 cells. In this study, PPF MM exhibit a significantly higher uptake efficiency than fructose‐free PCL‐PEG‐N₃/TPGS mixed micelles in both 2D MCF‐7 cells and 3D tumor spheroids. Also, the presence of free d ‐fructose competitively inhibits the internalization of PPF MM in MCF‐7 cells other than L929 cells. PPF MM show selective tumor accumulation in MCF‐7 breast tumor bearing mice xenografts. Taken together, PPF MM represent a promising nanoscale carrier system to achieve GLUT5‐mediated cell specific delivery in cancer therapy.