Effects of molecular mass and surface treatment on adsorbed poly(methyl methacrylate) on silica

The behavior of relatively monodisperse adsorbed poly(methyl methacrylate) (PMMA) samples, from 19 to 587 kDa on silica, was studied using modulated differential scanning calorimetry and FTIR. On untreated Cab? O? Sil silica, the glass transition temperatures (T_gs) were higher (by around 30 °C), and the transitions were significantly broader (by a factor of 5–6) than those for the corresponding bulk samples. While the T_gs for the bulk polymers showed the expected dependence on molecular mass, the polymers on untreated silica showed little dependence, i.e., at the same adsorbed amounts, the glass transitions were very similar. The FTIR spectra of the adsorbed PMMA (on untreated silica) showed the presence of at least two resonances, one for the bound (hydrogen bonded to surface silanols) and another for free carbonyls. Fitting of the spectra allowed the estimation of the bound fractions of carbonyls that were dependent on the adsorbed amount, but not molecular mass. On Cab? O? Sil treated with hexamethyldisilizane (HMDS), the adsorbed PMMA exhibited glass transition behavior with little molecular‐mass dependence; the T_gs for the different PMMA samples were very similar to those of the high‐molecular mass bulk polymer, but with additional broadening of about a factor of 2. FTIR spectra for the PMMA samples on the treated silica did not show significant amounts of any of the hydrogen‐bonded carbonyl groups. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 649–658, 2008     

Bound fractions of methacrylate polymers adsorbed on silica using FTIR

The H‐bonding of carbonyl groups on a series of methacrylate polymers with silanols on fumed silica was studied with transmission FTIR. The set included poly(alkyl methacrylates) with alkyl groups, (n‐C_nH_2n+1) of n = 1, 2, 4, and 12 and poly(benzyl methacrylate). Shifts in the vibrational frequencies for bound carbonyl groups (of ～20 cm^?1 lower than those found in the bulk) were observed in the adsorbed polymer samples. A series of samples with different adsorbed amounts (varying from 0.5 to 2.0 mg m^?2) of each polymer was prepared to determine the effect of the side chain on the H‐bonding. The fractions of bound carbonyls, p, for each of the methacrylate polymers studied, were calculated from a model based on the ratios of the absorption coefficients of the bound to free carbonyl resonances, X (= α_b/α_f). The X values were determined from linear regressions of the ratios of the free to bound carbonyl intensities as a function of the amounts of adsorbed polymer, M_t. The bound fractions, p, were observed to decrease with increase in adsorbed amounts and with increase in the lengths of the side chains of the methacrylate polymers, except for poly(lauryl methacrylate) (PLMA). PLMA has a very low glass transition temperature (T_g) and is likely rubbery on the surface, whereas the other polymers are likely glassy at ambient temperature. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1911–1918, 2010     

Thermal analysis and FT‐IR studies of adsorbed poly(ethylene‐stat‐vinyl acetate) on silica

Adsorbed poly(ethylene‐stat‐vinyl acetate) (PEVAc) on fumed silica was studied using temperature‐modulated differential scanning calorimetry (TMDSC) and FT‐IR spectroscopy. The properties of the copolymers were compared with poly(vinyl acetate) (PVAc) and low density polyethylene (LDPE) as references. TMDSC analysis of the copolymer‐silica samples in the glass transition region was complicated for the copolymers because of the ethylene crystallinity. Nevertheless, examination of the glass transition region for small adsorbed amounts of these copolymers indicated the presence of tightly‐ and loosely‐bound polymer segments, similar to other polymers which have an attraction to silica. Compared with bulk polymers with the same composition, the tightly‐bound polymers showed an increased glass transition temperature (T_g) and a loosely‐bound fraction with a lower T_g than bulk. FT‐IR spectra of the surface copolymers indicated that the fraction of bound carbonyls (p) increased as the fraction of vinyl acetate in the copolymers decreased, consistent with the notion that the carbonyls from vinyl acetate preferentially find their way to the silica surface. Spectra from samples with different adsorbed amounts of polymer were used to obtain the amount of bound polymer (M_b) and the ratio of molar absorption coefficients of bound carbonyls to free carbonyls (X). The copolymers had very large p values (up to 0.8) at small adsorbed amounts and dependent on the composition of the polymer. However, an analysis of the bound fractions, based on only the vinyl acetate groups, superimposed the data, suggesting that the ethylene units simply dilute the vinyl acetate groups in the surface polymer. The sample with the smallest fraction of vinyl acetate did not show this behavior and may be considered to be “carbonyl poor.” © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 727–736     

Surface‐initiated atom transfer radical polymerization grafting of poly(2,2,2‐trifluoroethyl methacrylate) from flat silicon wafer surfaces

Poly(2,2,2‐trifluoroethyl methacrylate) (PTFEMA), a partially fluorinated polymer, was directly grafted from silicon wafer surfaces by a surface‐initiated atom‐transfer radical polymerization (ATRP). The polymer layer thickness increased linearly with monomer conversion and molecular weight of free polymers in solution. The thickness was mainly determined by the experimental conditions such as activator/deactivator ratio, monomer/catalyst ratio, and monomer concentration. PTFEMA layers of more than 100‐nm thick were obtained. The grafted PTFEMA chains were “living” and allowed the extension of a second block of PMMA. X‐ray photoelectron spectroscopy study showed that the chemical compositions at the surfaces agreed well with their theoretical values. A novel surface‐attachable difunctional initiator was also synthesized and applied to the grafting of PTFEMA. The grafting density was doubled using this difunctional initiator, from 0.48 to 0.86 chains/nm². © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1252–1262, 2006     

Methacrylic acid and methyl methacrylate oligomers adsorbed to porous isotactic poly(methyl methacrylate) ultrathin films and mechanistic studies of living template polymerization

Methacrylic acid (MAA), methyl methacrylate (MMA), methacrylamide, and oligomers of MAA and MMA were selected as a model of active radical species in living template polymerization using stereocomplex formation. The adsorption behaviors of the aforementioned model compounds were examined toward porous isotactic‐(it‐) poly(methyl methacrylate) (PMMA) ultrathin films on a quartz crystal microbalance, which was prepared by the extracting of syndiotactic‐(st‐) poly(methacrylic acid) (PMAA) from it‐PMMA/st‐PMAA stereocomplexes. The apparent predominant adsorption of oligomers to monomers was observed in both PMAA and PMMA oligomers, suggesting that the mechanism of template polymerization follows the pick up mechanism. Although vinyl monomers were not incorporated into the porous it‐PMMA ultrathin film, both PMMA and PMAA oligomers were adsorbed at the initial stages. However, adsorbed amounts were limited to about 5 and 15% at 0.1 mol L^?1, respectively, which are much smaller values than corresponding st‐polymers. The results imply that radical coupling reaction is prevented during template polymerization to support the resulting living polymerization. ATR‐IR spectral patterns of oligomer complexes and it‐PMMA slightly changed in both cases, suggesting complex formation. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5879–5886, 2008     

PMMA adsorption over previously adsorbed PS studied by polarized FTIR-ATR

Polarized infrared spectroscopy in attenuated total reflection was used to investigate the adsorption of PMMA (polymethylmethacrylate) onto PS (polystyrene) that was previously adsorbed onto oxidized silicon from dilute solution in carbon tetrachloride at 30°C. The carbonyl group of PMMA forms hydrogen bonds with surface silanol groups, giving segment-surface interaction energy of 4 kT as against 1 kT for PS (k is the Boltzmann constant, T the absolute temperature). The formation of hydrogen-bonding by PMMA was unaffected, in rate or amount, by preadsorbed PS, but a lesser total amount of PMMA adsorbed onto PS, resulting in a higher average bound fraction. The histogram of the mass adsorbed, attributable to subpopulations of chains with different bound fractions, was inferred by subtracting infrared spectra acquired at successive times. Whereas this histogram was broad and bimodal for adsorption onto bare surface, it was narrower and unimodal for adsorption onto preadsorbed PS. © 1995 John Wiley & Sons, Inc.     

Synthesis of amphiphilic poly(methyl methacrylate‐ b‐ethylene oxide) copolymers from monohydroxy telechelic poly(methyl methacrylate) as macroinitiator

The synthesis of well‐defined poly(methyl methacrylate)‐block‐poly(ethylene oxide) (PMMA‐b‐PEO) dibock copolymer through anionic polymerization using monohydroxy telechelic PMMA as macroinitiator is described. Living anionic polymerization of methyl methacrylate was performed using initiators derived from the adduct of diphenylethylene and a suitable alkyllithium, either of which contains a hydroxyl group protected with tert‐butyldimethylsilyl moiety in tetrahydrofuran (THF) at ?78 °C in the presence of LiClO₄. The synthesized telechelic PMMAs had good control of molecular weight with narrow molecular weight distribution (MWD). The ¹H NMR and MALDI‐TOF MS analysis confirmed quantitative functionalization of chain‐ends. Block copolymerization of ethylene oxide was carried out using the terminal hydroxyl group of PMMA as initiator in the presence of potassium counter ion in THF at 35 °C. The PMMA‐b‐PEO diblock copolymers had moderate control of molecular weight with narrow MWD. The ¹H NMR results confirm the absence of trans‐esterification reaction of propagating PEO anions onto the ester pendants of PMMA. The micellation behavior of PMMA‐b‐PEO diblock copolymer was examined in water using ¹H NMR and dynamic light scattering. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2132–2144, 2008     

Interactions and prediction of phase diagrams in ternary blends comprising poly(vinyl acetate), poly(vinyl p‐phenol), and poly(methyl methacrylate)

This study investigated and discovered a new miscible ternary blend system comprising three amorphous polymers: poly(vinyl acetate) (PVAc), poly(vinyl p‐phenol) (PVPh), and poly(methyl methacrylate) (PMMA) using thermal analysis and optical and scanning electron microscopies. The ternary compositions are largely miscible except for a small region of borderline ternary miscibility near the side, where the binary blends of PVAc/PMMA are originally of a borderline miscibility with broad T_g. In addition to the discovering miscibility in a new ternary blend, another objective of this study was to investigate whether the introduction of a third polymer component (PVPh) with hydrogen bonding capacity might disrupt or enhance the metastable miscibility between PVAc and PMMA. The PVPh component does not seem to exert any “bridging effect” to bring the mixture of PVAc and PMMA to a better state of miscibility; neither does the Δχ effect seem to disrupt the borderline miscible PVAc/PMMA blend into a phase‐separated system by introducing PVPh. Apparently, the ternary is able to remain in as a miscible state as the binary systems owing to the fact that PVPh is capable of maintaining roughly equal H‐bonding interactions with either PVAc or PMMA in the ternary mixtures to maintain balanced interactions among the ternary mixtures. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1147–1160, 2006     

Heteroarm H‐shaped terpolymers through click reaction

Heteroarm H‐shaped terpolymers, (polystyrene)(poly(methyl methacrylate))‐ poly(tert‐butyl acrylate)‐(polystyrene)(poly(methyl methacrylate)), (PS)(PMMA)‐PtBA‐(PMMA)(PS), and, (PS)(PMMA)‐poly(ethylene glycol)(PEG)‐(PMMA)(PS), through click reaction strategy between PS‐PMMA copolymer (as side chains) with an alkyne functional group at the junction point and diazide end‐functionalized PtBA or PEG (as a main chain). PS‐PMMA with alkyne functional group was prepared by sequential living radical polymerizations such as the nitroxide mediated (NMP) and the metal mediated‐living radical polymerization (ATRP) routes. The obtained H‐shaped polymers were characterized by using ¹H‐NMR, GPC, DSC, and AFM measurements. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1055–1065, 2007     

Star polymers with POSS via azide–alkyne click reaction

Azidopropyl‐heptaisobutyl‐substituted polyhedral oligomeric silsesquioxane (POSS‐N₃) was reacted with 1,1,1‐tris[4‐(2‐propynyloxy)phenyl]‐ethane ( 1 ) and poly(ethylene glycol) (PEG)‐b‐poly(methyl methacrylate) (PMMA) copolymer with alkyne at its center (PEG‐PMMA‐alkyne) affording the first time synthesis of 3‐arm star POSS and PEG‐PMMA‐POSS 3‐miktoarm star terpolymer, respectively, in the presence of CuBr/N,N,N′,N″,N″‐pentamethyldiethylenetriamine as catalyst and N,N‐dimethylformamide/tetrahydrofuran as solvent at room temperature. The precursors and the target star polymers were characterized comprehensively by ¹H NMR, GPC, and DSC. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5947–5953, 2009     

High‐molecular‐weight symmetrical multiblock copolymers: Synthesis by RAFT polymerization and characterization

High‐molecular‐weight (MW) symmetrical multiblock copolymers, based on the hydrophobic monomers styrene (Sty) and methyl methacrylate (MMA), and the more polar monomer, 2‐vinyl pyridine (2VPy), were prepared using stepwise reversible addition‐fragmentation chain transfer polymerization. All copolymers shared a common poly(ethylene glycol) (PEG) midblock, introduced as a bifunctional macromolecular chain transfer agent. In total, five ABA triblock copolymers, five ABCBA pentablock terpolymers, and two ABCDCBA heptablock quaterpolymers (comprising four different monomer types) were synthesized. The MWs of the multiblock polymers were determined using gel permeation chromatography (GPC) and proton nuclear magnetic resonance (¹H NMR) spectroscopy, with the latter values being closer to the theoretically expected, whereas GPC MW distributions were relatively narrow, broadening with the number of blocks. The compositions of the synthesized polymers, as determined by ¹H NMR spectroscopy, were also close to the expected values. Finally, films cast from chloroform solutions of the pentablock terpolymers P2VPy‐b‐PSty‐b‐PEG‐b‐PSty‐b‐P2VPy, PSty‐b‐PMMA‐b‐PEG‐b‐PMMA‐b‐PSty, and P2VPy‐b‐PMMA‐b‐PEG‐b‐PMMA‐b‐P2VPy examined using transmission electron microscopy exhibited PSty and PMMA cylinders (first two) and lamellae (third terpolymer). © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4957–4965     

Synthesis of PMMA‐b‐PBA block copolymer in homogeneous and miniemulsion systems by DPE controlled radical polymerization

In this research, poly(methyl methacrylate)‐b‐poly(butyl acrylate) (PMMA‐b‐PBA) block copolymers were prepared by 1,1‐diphenylethene (DPE) controlled radical polymerization in homogeneous and miniemulsion systems. First, monomer methyl methacrylate (MMA), initiator 2,2′‐azobisisobutyronitrile (AIBN) and a control agent DPE were bulk polymerized to form the DPE‐containing PMMA macroinitiator. Then the DPE‐containing PMMA was heated in the presence of a second monomer BA, the block copolymer was synthesized successfully. The effects of solvent and polymerization methods (homogeneous polymerization or miniemulsion polymerization) on the reaction rate, controlled living character, molecular weight (M_n) and molecular weight distribution (PDI) of polymers throughout the polymerization were studied and discussed. The results showed that, increasing the amounts of solvent reduced the reaction rate and viscosity of the polymerization system. It allowed more activation–deactivation cycles to occur at a given conversion thus better controlled living character and narrower molecular weight distribution of polymers were demonstrated throughout the polymerization. Furthermore, the polymerization carried out in miniemulsion system exhibited higher reaction rate and better controlled living character than those in homogeneous system. It was attributed to the compartmentalization of growing radicals and the enhanced deactivation reaction of DPE controlled radical polymerization in miniemulsified droplets. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4435–4445, 2009     

Attachment of bis‐(trifluoromethyl)aryl labels onto the chain ends of poly(ethylene terephthalate) (PET) track‐etched membranes and films by surface wet chemistry

Organic chemistry performed at the solid–liquid interface allowed us to achieve the selective chain‐end functionalization of poly(ethylene terephthalate) (PET) membranes and films with perfluorinated labels. The carboxyl endings were activated with water‐soluble carbodiimide and were coupled to 3,5‐bis(trifluoromethyl)benzylamine (1) in aqueous acetonitrile, whereas the hydroxyl endings were activated by tosylation and were also coupled to 1. 3,5‐Bis(trifluoromethyl)phenyl isocyanate (2) was directly fixed on the hydroxyl endings of the polymer substrates in dry organic media. All the derivatized materials were analyzed by X‐ray photoelectron spectroscopy, allowing the quantitative determination of the amounts of surface‐grafted labels. Yields were between 10 and 100 pmol/cm². These surface reactivity assays mimic at best the experimental conditions that would be applied for the covalent anchorage of biologically active molecules onto PET substrates used in cell culture systems. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3510–3520, 2000     

Preparation and properties of polyhedral oligosilsequioxane tethered aromatic polyamide nanocomposites through Michael addition between maleimide‐containing polyamides and an amino‐functionalized polyhedral oligosilsequioxane

Polyhedral oligosilsequioxane (POSS) tethered aromatic polyamide nanocomposites with various POSS fractions were prepared through Michael addition between maleimide‐containing polyamides and amino‐functionalized POSS. The chemical structures of the polyamide–POSS nanocomposites were characterized with Fourier transform infrared and ¹H NMR. The polyamide–POSS nanocomposites exhibited good homogeneity in scanning electron microscopy and transmission electron microscopy observations. POSS modification increased the storage modulus and Young's modulus of the polyamides, slightly decreased their glass‐transition temperatures from 312 to 305 °C, and significantly lowered their dielectric constants from 4.45 to 3.35. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4632–4643, 2006     

Effect of the polymer matrix on the formation of silver nanoparticles in polymer–silver salt complex membranes

When polymer–silver salt complex membranes were exposed to UV irradiation, the separation performances of both the permeance and selectivity for propylene–propane decreased, which was primarily attributed to the reduction of the silver ions in the membranes to silver nanoparticles. Here, the effect of the polymer matrix on the formation of silver nanoparticles in the polymer–silver salt complex membranes was investigated. This effect was assessed for the complexes of two kinds of silver salts (AgBF₄ and AgCF₃SO₃) with several polymeric ligands containing three different carbonyl groups, including poly(vinyl pyrrolidone) (PVP) with an amide group, poly(vinyl methyl ketone) (PVMK) with a ketone group, and poly(methyl methacrylate) (PMMA) with an ester group. UV–vis spectra and transmission electron microscopy (TEM) images clearly indicated that the reduction rate of the silver ions has the following order in the various polymer matrices: PVP > PVMK > PMMA, whereas the size and the distribution of the nanoparticles exhibited the reverse order. The tendency to form silver nanoparticles was explained in terms of the differences between the comparative strengths of the interactions of the silver ions with the different carbonyl oxygens in the matrices, as well as that of the silver ions with counteranions, which was characterized by X‐ray photoelectron spectroscopy (XPS) and FT‐Raman spectroscopy. It was concluded that when the concentration of free silver ions was low due to weak polymer–silver ion and strong silver ion–anion interactions, as found with PMMA, the reduction rate of silver ions to silver nanoparticles was slow. Therefore, the PMMA–silver complex membranes were less sensitive to decreases in separation performance upon UV irradiation than compared to the PVP membranes. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1168–1178, 2006     

Fabrication of well‐developed nano‐ribbons composed of hierarchically grown isotactic poly(methyl methacrylate) crystals on substrates

Well‐developed nano‐ribbons composed of isotactic poly(methyl methacrylate) (it‐PMMA) were successfully fabricated on mica via a simple solution‐casting method. Typical morphologies with about 0.6 nm thickness and 30–40 nm widths, thermal stability, and alternative structural analyses suggested that nano‐ribbons were composed of two‐dimensional folded chain crystals of it‐PMMA. Typically, nano‐ribbons were developed by incubating tetrahydrofuran (THF) solutions at 20 °C for at least 2 months, more than equi‐amounts of water were added to incubated THF solutions, and solutions were cast onto mica. It was found that, after the aforementioned incubation of THF solutions, it‐PMMA chains adopted trans‐trans (tt) conformations, which are precursors for it‐PMMA crystals, suggesting that THF is a unique solvent for it‐PMMA. By adding water, a poor solvent for it‐PMMA, to THF solutions, it‐PMMA aggregates formed with several hundreds of nanometer sizes, further promoting an increase in the population of the tt conformation. Nano‐ribbons were similarly formed on silicon wafer substrates, suggesting that hydrophilic substrates were essential for the formation of nano‐ribbons. Interestingly, a modulation of the above described method, with the slight evaporation of THF from a THF/water solution before casting onto mica, succeeded in the development of epitaxially adsorbed nano‐ribbons. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3098–3110, 2009     

Thermal Analysis of Adsorbed Poly(methyl methacrylate) on Silica

Modulated differential scanning calorimetry has been used to quantify the glass transitions of small adsorbed amounts of poly(methyl methacrylate) (PMMA) on silica. While a relatively narrow, single glass transition was found for bulk PMMA, broader two-component transitions were found for the adsorbed polymer. A two-state model based on loosely bound polymer (glass transition similar to bulk) and more tightly bound polymer (glass transition centered around 156 degrees C) was used to interpret the thermograms. On the basis of this model, the amount of tightly bound polymer was found to be approximately 1.3 mg/m2, corresponding to a 1.1 nm thick layer. The change in heat capacity for the tightly bound polymer at the glass transition temperature was estimated to be about 16% of that of the bulk polymer.     

Synthesis and characterization of poly(methyl methacrylate)/casein nanoparticles with a well‐defined core‐shell structure

Well‐defined, core‐shell poly(methyl methacrylate) (PMMA)/casein nanoparticles, ranging from 80 to 130 nm in diameter, were prepared via a direct graft copolymerization of methyl methacrylate (MMA) from casein. The polymerization was induced by a small amount of alkyl hydroperoxide (ROOH) in water at 80 °C. Free radicals on the amino groups of casein and alkoxy radicals were generated concurrently, which initiated the graft copolymerization and homopolymerization of MMA, respectively. The presence of casein micelles promoted the emulsion polymerization of the monomer and provided particle stability. The conversion and grafting efficiency of the monomer strongly depended on the type of radical initiator, ROOH concentration, casein to MMA ratio, and reaction temperature. The graft copolymers and homopolymer of PMMA were isolated and characterized with Fourier transform infrared spectroscopy and differential scanning calorimetry. The molecular weight determination of both the grafted and homopolymer of PMMA suggested that the graft copolymerization and homopolymerization of MMA proceeded at a similar rate. The transmission electron microscopic image of the nanoparticles clearly showed a well‐defined core‐shell morphology, where PMMA cores were coated with casein shells. The casein shells were further confirmed with a zeta‐potential measurement. Finally, this synthetic method allowed us to prepare PMMA/casein nanoparticles with a solid content of up to 31%. Thus, our new process is commercially viable. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3346–3353, 2003     

Surface and interface morphology of polystyrene/poly(methyl methacrylate) thin‐film blends and bilayers

The surface and interface morphologies of polystyrene (PS)/poly(methyl methacrylate) (PMMA) thin‐film blends and bilayers were investigated by means of atomic force microscopy (AFM) and X‐ray photoelectron spectroscopy. Spin‐coating a drop of a PS solution directly onto a PMMA bottom layer from a common solvent for both polymers yielded lateral domains that exhibited a well‐defined topographical structure. Two common solvents were used in this study. The structure of the films changed progressively as the concentration of the PS solution was varied. The formation of the blend morphology could be explained by the difference in the solubility of the two polymers in the solvent and the dewetting of PS‐rich domains from the PMMA‐rich phase. Films of the PS/PMMA blend and bilayer were annealed at temperatures above their glass‐transition temperatures for up to 70 h. All samples investigated with AFM were covered with PS droplets of various size distributions. Moreover, we investigated the evolution of the annealed PS/PMMA thin‐film blend and bilayer and gave a proper explanation for the formation of a relatively complicated interface inside a larger PS droplet. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 9–21, 2006     

Synthesis and characterization of pyrene bearing amphiphilic miktoarm star polymer and its noncovalent interactions with multiwalled carbon nanotubes

A novel amphiphilic miktoarm star polymer, polystyrene‐poly(ethylene glycol)‐poly(methyl methacrylate), bearing a pyrene group at the end of PS arm (Pyrene‐PS‐PEG‐PMMA) was successfully synthesized via combination of atom transfer radical polymerization and click chemistry. The structure and composition of the amphiphilic miktoarm star polymer were characterized by gel permeation chromatography and ¹H NMR. The functionalization of multiwalled carbon nanotubes (MWCNTs) via “π–π” stacking interactions with pyrene‐PS‐PEG‐PMMA miktoarm star polymer was accomplished and the resulting polymer‐MWCNTs hybrid was analyzed by using ¹H NMR, UV–vis, fluorescence spectroscopy, and thermal gravimetric analysis. The high‐resolution transmission electron microscopy and analytical techniques aforementioned confirmed that the noncovalent functionalization of MWCNT's with the amphiphilic miktoarm star polymer was successfully achieved. The MWCNT/pyrene‐PS‐PEG‐PMMA exhibited significant dispersion stability in common organic solvents such as dimethyl formamide, chloroform, and tetrahydrofuran. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012