Effect of TiO2–Ti and TiO2–TiN composite coatings on corrosion behavior of NiTi alloy

Two kinds of biocompatible coatings were produced in order to improve the corrosion resistance of nickel titanium (NiTi) alloy. A titanium oxide–titanium (TiO₂–Ti) composite was coated on NiTi alloy using electrophoretic method. After the coating process, the samples were heat‐treated at 1000 °C in two tube furnaces, the first one in argon atmosphere and the second one in nitrogen atmosphere at 1000 °C. The morphology and phase analysis of coatings were investigated using scanning electron microscopy and X‐ray diffraction analysis, respectively. The electrochemical behavior of the NiTi and coated samples was examined using polarization and electrochemical impedance spectroscopy tests. Electrochemical tests in simulated body fluid demonstrated a considerable increase in corrosion resistance of composite‐coated NiTi specimens compared to the non‐coated one. The heat‐treated composite coating sample in nitrogen atmosphere had a higher level of corrosion resistance compared to the heat‐treated sample in argon atmosphere, which is mainly due to having nitride phases. Copyright © 2014 John Wiley & Sons, Ltd.     

Discovery and Structure Determination of an Unusual Sulfide Telluride through an Effective Combination of TEM and Synchrotron Microdiffraction

The structure elucidation of the novel sulfide telluride Pb₈Sb₈S₁₅Te₅ demonstrates a new versatile procedure that exploits the synergism of electron microscopy and synchrotron diffraction methods for accurate structure analyses of side‐phases in heterogeneous microcrystalline samples. Suitable crystallites of unknown compounds can be identified by transmission electron microscopy and relocated and centered in a microfocused synchrotron beam by means of X‐ray fluorescence scans. The refined structure model is then confirmed by simulating HRTEM images of the same crystallite. Pb₈Sb₈S₁₅Te₅ consists of chains of heterocubane‐like units. Cation coordination polyhedra form unusually entwined chains of edge‐ and face‐sharing bicapped trigonal prisms. The structure data are precise enough for bond‐valence calculations, which confirm the disordered atom distribution. On this basis, optimization of physical properties becomes feasible.     

Effect of formulation of silica‐based solution on corrosion resistance of silicate coating on hot‐dip galvanized steel

Several silica‐based solutions with 50 g/l of SiO₂ were prepared from sodium silicate solutions and silica sol; the silicate conversion coatings were obtained by immersing hot‐dip galvanized steel sheets in these solutions. These solutions were characterized using high‐resolution transmission electron microscopy and ²⁹Si nuclear magnetic resonance; the morphology of the coatings was observed by SEM and atomic force microscopy while the corrosion resistance was evaluated by electrochemical measurements as well as neutral salt spray tests. The results show that the coatings obtained from the single silica sol solution had poor adhesion and the coating obtained from the sodium silicate solution with low SiO₂/Na₂O molar ratio was uneven. By adding the silica sol to the silicate solution with low molar ratio, uniform coatings with better protection property were obtained. According to the results of ²⁹Si nuclear magnetic resonance spectra, the effects of the distribution of silicate anions with various polymerization degrees in the silica‐based solutions on the microstructure and corrosion resistance of the silicate coatings are discussed. Copyright © 2016 John Wiley & Sons, Ltd.     

Human Serum Albumin Nanotubes with Esterase Activity

A nanocylindrical wall structure was obtained by layer‐by‐layer (LbL) assembly of poly‐L ‐arginine (PLA) and human serum albumin (HSA) and characterized by scanning electron microscopy (SEM), scanning force microscopy (SFM), and cryogenic transmission electron microscopy (cryo‐TEM). SEM and SFM measurements of a lyophilized powder of (PLA/HSA)₃ nanotubes yielded images of round, chimney‐like architectures with approximately 100 nm wall thickness. Cryo‐TEM images of the hydrated sample revealed that the tube walls are composed of densely packed HSA molecules. Moreover, when small‐angle X‐ray scattering was used to characterize the individual PLA and HSA components in aqueous solutions, maximum diameters of approximately 28 nm and 8 nm were obtained, respectively. These values indicate the minimum thickness of wall layers consisting of PLA and HSA. It can also be concluded from SEM as well as from cryo‐TEM images that the protein cylinders are considerably swollen in the presence of water. Furthermore, HSA retains esterase activity if assembled in nanotubes, as indicated by measurements of para‐nitrophenyl acetate hydrolysis under semi‐physiological conditions (pH 7.4, 22 °C). The enzyme activity parameters (Michaelis constant, K_m, and catalytic constant, k_cat) were comparable to those of free HSA.     

Corrosion protection performance of ceria‐copolymer bilayer coating on low nickel stainless steel in 0.5 M H2SO4 medium

In this paper, we have reported the anti‐corrosion performance of ceria / poly (indole‐co‐pyrrole) (Ce/(poly(In‐co‐Py)) bilayer coating on low nickel stainless steel (LN SS). Electrochemical polymerization of (poly (In‐co‐Py)) was achieved on ceria‐coated LN SS (CeO₂/LN SS) in acetonitrile medium containing LiClO₄ (ACN‐LiClO₄) by cyclic voltammetric technique. The coatings were characterized by analytical techniques like Fourier transform infrared spectroscopy, scanning electron microscopy with energy dispersive analysis of X‐ray, respectively. The mechanical behavior of the coatings was studied using peel test, hardness and wear resistance tests. The corrosion defensive performance of this bilayer coating on LN SS was investigated using electrochemical techniques such as potentiodynamic polarization and electrochemical impedance spectroscopy in 0.5 M H₂SO₄. These results show that the bilayer coating on LN SS lowered the permeability of corrosive ions present in the acidic medium and thus acts as a barrier against the attack of corrosive environment. Copyright © 2012 John Wiley & Sons, Ltd.     

Growth and SIMS study of d.c.‐sputtered indium oxide films on silicon

Indium oxide thin films were grown onto Si and quartz substrates by d.c. reactive sputtering of elemental indium. X‐ray diffraction and transmission electron microscopy studies confirmed the single‐phase and polycrystalline nature of the films. Secondary ion mass spectrometry investigations of In₂O₃/Si structures showed the formation of an inhomogeneous interface region ～20 nm thick between In₂O₃ and Si. The overall feature of the interface remained the same under annealing in an oxygen atmosphere, but annealing in an argon atmosphere drastically altered the nature of the interface. The observations indicate that interface formation and stability depend critically on the availability of oxygen. Copyright © 2005 John Wiley & Sons, Ltd.     

Interface characterization of nickel contacts to bulk bismuth tellurium selenide

Transmission electron microscopy (TEM) characterization of nickel contacts to bulk bismuth tellurium selenide [Bi₂(Te,Se)₃] is reported. Samples were prepared in a dual column focused ion beam/scanning electron microscope (FIB/SEM) system using a lift‐out technique, with ion beam energy and exposure times carefully optimized to minimize sample damage. Diffusion of Ni into Bi₂(Te,Se)₃ was observed and the formation of a nickel telluride (NiTe) interfacial region confirmed after heat treatment at 200 °C. Selected area diffraction patterns provided evidence of a modified bismuth telluride–like structure at the interface, identified by analytical electron microscopy to be composed of Ni and Bi₂(Te,Se)₃. Copyright © 2009 John Wiley & Sons, Ltd.     

Interaction of silicic acid with poly(1‐vinylimidazole)

Poly(1‐vinylimidazole) reacts with silicic acid and poly(silicic acid), giving rise to water‐soluble complexes and insoluble composites because of hydrogen bonding. The composition, structure, and morphology of the obtained products have been studied with elemental analysis, Fourier transform infrared spectroscopy, and scanning electron microscopy. The main direction of the reaction depends not only on the initial ratio of the components, concentration, and pH but also on the sequence of the reagent mixing: the presence of poly(1‐vinylimidazole) macromolecules during the formation of silicic acid stabilizes soluble complexes, which precipitate with an excess of H₄SiO₄ only. These soluble complexes may serve as a pattern of particles responsible for the transport of silicic acid in diatom algae and other organisms that assimilate silicon from the environment. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 820–827, 2006     

Formation of a tetragonal Cu3Au alloy at gold/copper interfaces

A gold–copper alloy with a nominal composition of Cu₃Au but with a tetragonal (c = 4a) structure is observed to form at Au/Cu interfaces of gold/copper multilayers deposited on amorphous substrates by d.c. magnetron sputtering. The formation of this non‐equilibrium structure (tentatively D0₂₃) under‐ambient conditions is detected by secondary ion mass spectrometry, x‐ray diffraction and high‐resolution cross‐sectional transmission electron microscopy. Co‐sputtering of Au and Cu under similar conditions produces only conventional fcc Cu₃Au alloy phases, suggesting that interfacial confinement plays a significant role in producing the novel Cu₃Au alloy phase in gold/copper multilayers. Copyright © 2003 John Wiley & Sons, Ltd.     

Electron Beam Induced Transformation of MoO3 to MoO2 and a New Phase MoO

The transformation of MoO₃ induced by electron beam irradiation was studied by electron energy‐loss spectroscopy (EELS) in combination with electron diffraction and high‐resolution transmission electron microscopy (HRTEM) techniques. The routes of structure transformation were dependent on the applied electron current density. In case of low current density, MoO₂ was obtained. In case of high current density, MoO with a rock‐salt structure is suggested to be the final phase. The change in oxidation states of the Mo oxides was deduced from the features in energy‐loss near edge structure (ELNES) of the O K‐edge. Quantitative analysis was successfully employed on Mo M₃‐edge and O K‐edge to obtain the O/Mo ratio of the reduced phases. The mechanisms of different structure transformation behaviors were suggested in the frame of radiolysis enhanced diffusion.     

Corrosion and wear resistance properties of multilayered diamond‐like carbon nanocomposite coating

Multilayered diamond‐like carbon (DLC) nanocomposite coating has been deposited on silicon and stainless steel substrates by combination of cathodic arc evaporation and magnetron sputtering. In order to make DLC coating adhered to metal substrate, a chromium interlayer has been deposited with constant bias voltage of −150 V applied to the substrate. Dense multilayered coating consists of metallic or nonmetallic and tetrahedral carbon (ta‐C) layers with total thickness of 1.44 μm. The coating has been studied for composition, morphology, surface nature, nanohardness, corrosion resistance, and tribological properties. The composition of the coating has been estimated by energy‐dispersive spectroscopy. Field‐emission scanning electron microscopy and atomic force microscopy have been used to study the surface morphology and topography. I_D/I_G ratio of ta‐C:N layer obtained from Raman spectroscopy is 1.2, indicating the disorder in the layer. X‐ray photoelectron spectroscopy studies of individual ta‐C:N, CrN, and Cr‐doped DLC layers confirm the presence of sp²C, sp³C, CrN, Cr₂N, and carbidic carbon, and sp²C, sp³C, and Cr carbide. Nanohardness studies show the maximum penetration depth of 70 to 85 nm. Average nanohardness of the multilayered DLC coating is found to be 35 ± 2.8 GPa, and Young's modulus is 270 GPa. The coating demonstrates superior corrosion resistance with better passivation behavior in 3.5% NaCl solution, and corrosion potential is observed to move towards nobler (more positive) values. A low coefficient of friction (0.11) at different loads is observed from reciprocating wear studies. Wear volume is lower at all loads on the multilayered DLC nanocomposite coating compared to the substrate.     

Cross‐sectional high‐resolution microscopy of thin pretreatment layers on hot dip galvanized steel

Hexavalent chromium containing pretreatments and primers for coil coating are soon to be entirely prohibited, which sets new demands for Cr‐free alternatives. Most of the presently used Cr‐free pretreatment layers operate predominantly via barrier formation and adhesion promotion mechanisms and lack the self‐healing effect typical for Cr⁶⁺‐pretreatments. This sets new demands also for the formation and monitoring of these layers. The barrier thickness and chemical composition of Cr‐free pretreatment layers on hot dip galvanized steel were studied using cross sections from broad ion beam (BIB) sample preparation and ultramicrotome cutting. BIB milling provided finely polished cross sections of pretreated samples. Film thicknesses of 20–50 nm were accurately determined for Cr‐free pretreatments containing 4–10 mg Ti/m² using BIB milling and scanning electron microscopy imaging. Scanning transmission electron microscopy, integrated with aberration correctors and X‐ray energy dispersive spectrometry, of an ultramicrotome cut pretreated and painted samples provided detailed chemical information. Metal complexes were detected close to the pretreatment/zinc interface, while the polymeric part of the pretreatment layer prevailed closer to paint. Copyright © 2014 John Wiley & Sons, Ltd.     

Structural Study of Micro and Nanotubes Synthesized by Rapid Thermal Chemical Vapor Deposition

The structures of micro and nanotubes obtained by pyrolysis of hydrocarbons, hold onto silicon (Si) substrates, are reported in this work. The tubes fabrication experiments were carried out by Rapid Thermal Chemical Vapor Deposition (RTCVD) using propane (C₃H₈) as carbon (C) precursor. Selection of parameters such as temperature of deposition, vacuum conditions or surface cleaning leads to the creation of tubular structures. Transmission electron microscopy (TEM), scanning electron microscopy (SEM), selected area electron diffraction (SAED) and energy dispersive X-ray measurements (EDX) are the microbeam techniques that allow to characterize the tubes found in the studied specimens. Different tube configurations such as isolated nanorods, Y-type junctions or fiber-like layers are evidenced. Metallic catalysis seems to be the mechanism involved in the wires formation since Fe particles are present inside the CNT tubes. Other poly-crystalline inclusions are also evidenced by SAED. The composition of the nanotubes changes from tip to tail in an amorphous matrix. The growth mechanisms leading to tube formation are described.     

Effects of anodic oxidation on corrosion properties of Al coating by arc spraying in seawater

A layer of Al coatings was prepared on the S355 steel by arc spraying, which was conducted by anodic oxidation treatment; the morphologies, chemical element compositions and phases of Al coating, and anodic oxide layer were analyzed with field emission scanning electron microscope (FESEM), energy dispersive spectrometer (EDS) and X‐ray diffraction (XRD), respectively. The corrosion protections of Al coating before and after anodic oxidation were discussed with a seawater immersion test; the corrosion resistance mechanisms of Al coating and anodic oxide layer in the seawater were also investigated. The results show that the thickness of Al coating is about 300 µm by arc spraying, the sample surfaces become loose after seawater immersion corrosion and Cl^? and O^2? penetrate into the substrate from the cracks, destroying the binding properties of coating–substrate, and the coating fails. After anodic oxidation, the oxide layer is formed in the surface of Al coating with the thickness of about 30 µm; the corrosion products are mainly composed of Al(OH)₃, which barraged the holes caused by seawater corrosion. The corrosion cracks are formed during the corrosion, while the number and depth of cracks decrease obviously after anodic oxidation treatment. The corrosion of Al coating becomes the local corrosion after anodic oxidation treatment, and the grains are smaller, which are easily nucleated to form a new corrosion resistance layer. Copyright © 2015 John Wiley & Sons, Ltd.     

Investigation of copper patinas using ion beam analysis and scanning electron microscopy

Ion beam analysis (IBA) techniques were applied successfully to the investigation of non‐corroded and artificially corroded patina layers grown on copper substrates in order to explore their potential use in the study of degradation phenomena of copper and copper alloys subjected to chemical treatment and exposed to selected environmental conditions. Rutherford backscattering spectroscopy (RBS) with deuterons as projectiles and the nuclear reactions ¹⁶O(d,p)¹⁷O and ³²S(p,p′γ)³²S were applied to the investigation of the depth distribution of oxygen and sulphur in near‐surface layers of synthetic patina consisting of mineral phases corresponding to chalcanthite as well as to cuprite + chalcanthite and antlerite + brochantite + chalcanthite. Electrochemical techniques (potentiodynamic polarization and cyclic voltammetry in 0.5 M Na₂SO₄) were used for artificial acceleration and study of the corrosion processes, and scanning electron microscopy (SEM/EDS) was used for examination of the surface morphology of the samples. A patinated roof sample from the Vienna Hofburg also was investigated using the same techniques. The measurement showed that IBA can provide valuable information for the study of patina near‐surface layers of thickness up to a few micrometres and indicated that cuprite was the mineral phase primarily formed on the copper substrates and the main component of the interface between the patina layer and the metallic substrate. The investigated copper patinas looked rather heterogeneous and were characterized by high porosity. Mixed patinas exhibited considerable stability to further corrosive attack. Copyright © 2005 John Wiley & Sons, Ltd.     

Influence of a Second Cation (M = Ca2+, Mg2+) on the Phase Evolution of (BaxM1–x)F2 Starting from Amorphous Deposits

A second type of cation (Mg²⁺, Ca²⁺) was introduced into BaF₂ by low‐temperature atomic beam deposition. The structure evolution from low‐temperature (–150 °C) amorphous deposits to high‐temperature (< 1000 °C) annealed crystalline phases was studied by in‐situ transmission electron microscopy and X‐ray diffraction. Amorphous (Ba_0.5, Ca_0.5)F₂ crystallizes in a first step to metastable solid solution phase (fluorite‐type), which then decomposes into the pure phases of CaF₂ and BaF₂ at higher temperature. The crystallization behavior of amorphous (Ba_xMg_1–x)F₂ is completely different. When the Mg/Ba atomic ratio is around 1:1, the mixture transforms to the ternary compound BaMgF₄ at annealing, and no decomposition occurs by further heating up to 1000 °C. When the Ba concentration is below 15 % in atomic ratio (x < 0.15), the mixture forms a solid solution phase (rutile type) with the lattice expanded by +1 % compared to rutile type MgF₂. The difference between the phase evolutions of the two mixture systems is discussed.     

Irreversible Structural Changes of Copper Hexacyanoferrate Used as a Cathode in Zn-Ion Batteries

The structural changes of copper hexacyanoferrate (CuHCF), a Prussian blue analogue, which occur when used as a cathode in an aqueous Zn-ion battery, are investigated using electron microscopy techniques. The evolution of Zn_xCu_1−xHCF phases possessing wire and cubic morphologies from initial CuHCF nanoparticles are monitored after hundreds of cycles. Irreversible introduction of Zn ions to CuHCF is revealed locally using scanning transmission electron microscopy. A substitution mechanism is proposed to explain the increasing Zn content within the cathode material while simultaneously the Cu content is lowered during Zn-ion battery cycling. The present study demonstrates that the irreversible introduction of Zn ions is responsible for the decreasing Zn ion capacity of the CuHCF cathode in high electrolyte concentration.     

Convenient extraction method for quantification of thin zinc patina layers

Synthetic zinc patina was grown on galvanized steel sheets in supercritical carbon dioxide atmosphere. Different patina compounds were dissolved and quantified using a stepwise immersion and dissolution procedure. The distinct patina components, namely anhydrous zinc carbonate (a dense layer adjacent to metallic zinc) and zinc hydroxy carbonate (nanowires on the surface), were dissolved in glycine solutions, followed by quantification of Zn²⁺ in the solutes by X‐ray fluorescence. The zinc hydroxy carbonate nanowires were readily glycine soluble, and the anhydrous zinc carbonate showed scarce glycine solubility, which enabled their selective quantification. The amount of the remaining (anhydrous) zinc carbonate after glycine extraction was determined from the glycine‐soluble zinc oxide after calcination (heat treatment for 10 minutes at 350°C). The results were verified by scanning electron microscopy imaging and Fourier transform infrared spectroscopy measurements.     

Formation of Eu2O3 Nanorods through Solvothermal Routes by Surfactant Assistance

Eu₂O₃nanorods were synthesized and characterized. The crystallites of Eu₂O(CO₃)₂·H₂O nanorods and Eu₂O₃ nanorods were obtained by means of surfactant assistance, with aqueous butanol solution as the solvent and hexamethylene tetramine as the base. The characteristics of the nanorods were analyzed by transmission electron microscopy, high‐resolution transmission electron microscopy, scanning electron microscopy and X‐ray diffraction. The Eu₂O₃ nanorod is about 80–300 nm in diameter and 1–5 µm in length. The formation mechanism of the 1D products was also proposed.     

Synthesis and characterization of polypyrrole nanofibers with different dopants

Nanostructures of polypyrrole (PPy) were synthesized in the presence of different dopants including hydrochloric acid (HCl), ferric chloride (FeCl₃), p‐toluene sulfonic acid (p‐TSA), camphor sulfonic acid (CSA), and polystyrene sulfonic acid (PSSA), using a simple interfacial oxidative polymerization method. The method is a reliable non‐template approach with relatively simple instrumentation, ease of synthesis, and economic viability for synthesizing PPy nanostructures. Morphology of synthesized PPy structures was investigated using scanning electron microscopy (SEM) and transmission electron microscopy (TEM), which indicate the formation of one‐dimensional (1D) nanofibers with average diameter of 75–180 nm. Energy dispersive spectrum (EDS) of the PPy nanofibers indicates the attachment of the dopants to the PPy backbone; the fact is further confirmed by the Fourier transform infrared (FTIR) spectra of PPy nanostructures. Thermal stabilities of the nanostructures explored using thermal gravimetric analysis (TGA) follow the order PPy‐p‐TSA > CSA > HCl > FeCl₃ > PSSA. It is noticed that the electrical conductivity (EC) of PPy nanostructures depends upon the nature of dopant (PPy‐p‐TSA > CSA > HCl > FeCl₃ > PSSA), PPy‐p‐TSA nanofibers showing the highest EC of 6 × 10^?2 Scm^?1. Copyright © 2009 John Wiley & Sons, Ltd.