Synthesis,photochemical and phase behavior of linear and hyperbranched photoactive benzylidene liquid‐crystalline polyesters

Photoactive hyperbranched benzylidene liquid‐crystalline polyester (PAHBP) and photoactive linear benzylidene liquid‐crystalline polyester (PALBP) were synthesized by solution polycondensation with pyridine as an acid acceptor. PAHBP and PALBP were thoroughly characterized with Fourier transform infrared, ¹H and ¹³C NMR, ultraviolet–visible spectrophotometry, fluorescent spectrophotometry, gel permeation chromatography, thermogravimetric analysis, differential scanning calorimetry, and polarized optical microscopy. Both polymers exhibited nematic mesophase. The glass‐transition temperature and liquid‐crystalline isotropic temperature of PAHBP were higher than those of PALBP. During photolysis under ultraviolet light, both polymers underwent an intermolecular photocycloaddition reaction, and the photoactivity of PAHBP was faster than that of PALBP; this was further confirmed by photoviscosity studies. PALBP and PAHBP were fluorescent in nature. An increase in the fluorescence intensity with the time of ultraviolet‐light irradiation was observed for both PAHBP and PALBP. The rate of increase in the fluorescence intensity of the linear analogue (PALBP) was higher than that of the hyperbranched polymer (PAHBP). This behavior could be attributed to the attainment of better planarity in the case of the linear one but not in the case of PAHBP because of the rapid crosslinking of PAHBP leading to an irregular architecture. This behavior was further confirmed by the calculation of the steric energy from corresponding model compounds. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3986–3994, 2006     

Effect of molecular architecture and size of mesogen on phase behavior and photoactive properties of photoactive liquid crystalline hyperbranched polyester epoxies containing benzylidene moiety

A series of photoactive liquid crystalline linear and hyperbranched polyester epoxies were synthesized by polyaddition of photoactive bis benzylidene alkanone diol monomers and terephthalic acid and trimesic acid respectively with good yield. The effect of molecular architecture (linear and hyperbranched), size of mesogenic unit (cyclic and acyclic units) on the physicochemical, thermal, mesogenic, and photoactive properties of hyperbranched polymers were studied and compared. Degree of branching of hyperbranched polymers was found to be in the range of 0.46–0.49. Monomers containing cyclic moieties only exhibited nematic mesophase, while all polymers exhibited typical nematic mesophase. Intermolecular photo cycloaddition reaction was studied by ultraviolet–visible spectra (UV–vis) and NMR spectroscopy and photo viscosity measurement of UV irradiated polymer solutions. Faster photo induced behavior of hyperbranched polymers containing acyclic alkanone moiety, as compared to polymers containing cycloalkanone moieties, was observed. The change in the refractive index was found to be in the range of 0.02–0.024. Substantial variation of refractive index indicates that this polymer could be used for optical recording. All the polymers were also found to be fluorescent in nature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 552–563, 2008     

Hydroxyl‐terminated hyperbranched aromatic poly(ether‐ester)s: Synthesis,characterization, end‐group modification,and optical properties

Novel AB₂‐type monomers such as 3,5‐bis(4‐methylolphenoxy)benzoic acid ( monomer 1 ), methyl 3,5‐bis(4‐methylolphenoxy) benzoate ( monomer 2 ), and 3,5‐bis(4‐methylolphenoxy)benzoyl chloride ( monomer 3 ) were synthesized. Solution polymerization and melt self‐polycondensation of these monomers yielded hydroxyl‐terminated hyperbranched aromatic poly(ether‐ester)s. The structure of these polymers was established using FTIR and ¹H NMR spectroscopy. The molecular weights (M_w) of the polymers were found to vary from 2.0 × 10³ to 1.49 × 10⁴ depending on the polymerization techniques and the experimental conditions used. Suitable model compounds that mimic exactly the dendritic, linear, and terminal units present in the hyperbranched polymer were synthesized for the calculation of degree of branching (DB) and the values ranged from 52 to 93%. The thermal stability of the polymers was evaluated by thermogravimetric analysis, which showed no virtual weight loss up to 200 °C. The inherent viscosities of the polymers in DMF ranged from 0.010 to 0.120 dL/g. End‐group modification of the hyperbranched polymer was carried out with phenyl isocyanate, 4‐(decyloxy)benzoic acid and methyl red dye. The end‐capping groups were found to change the thermal properties of the polymers such as T_g. The optical properties of hyperbranched polymer and the dye‐capped hyperbranched polymer were investigated using ultraviolet‐absorption and fluorescence spectroscopy. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5414–5430, 2008     

Molecular engineering of photoactive liquid crystalline polyester epoxies containing benzylidene moiety

A series of photoactive liquid crystalline polyester epoxies incorporating bisbenzylidene segments as photoactive mesogenic cores were synthesized by polyaddition of diepoxy monomers and terephthalic acid/trimesic acid. To investigate the influence of structural parameters such as, molecular architecture, structural rigidity of mesogenic unit and substituents on thermal, mesogenic, and photoactive properties, the bisbenzylidene segment was incorporated into one acyclic and two cycloalkanone units with two and four substituents, respectively in both linear and hyperbranched architectures. Degree of branching of hyperbranched polymers was found to be in the range of 0.49–0.62. All polymers exhibited nematic mesophase (nematic droplets). Photo induced (2π + 2π) cycloaddition reaction, upon exposure to light at 365 nm, was examined. Inter molecular photocycloaddition was confirmed by photoviscosity measurement of UV irradiated polymer solutions. Faster photo induced reactivity of polymers in hyperbranched architecture was observed when compared to linear structure. Acyclic units facilitated photocycloaddition, and five‐membered ring showed higher photoactivity compared to six‐membered ring. The steric hindrance caused by substituents decreased the photoactivity of polymers. Refractive index change was found to be in the range of 0.015–0.024. Substantial variation of refractive index indicates that these polymers could be used for optical recording. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7637–7655, 2008     

Hyperbranched photo responsive and liquid crystalline azo‐siloxane polymers synthesized by click chemistry

Three new types of hyperbranched photoactive liquid crystalline siloxane polymers containing azo moieties were synthesized using click chemistry methodology. The polymers were soluble in most of the polar solvents like chloroform, tetrahydrofuran, dimethylformamide, dimethyl sulphoxide and dichloromethane. The molecular weights of the polymers were in the range of 9000–12,000 g mol^?1. The trans‐cis photoisomerization of the polymer were studied both under UV radiation and dark. The isomerization rate constants were found to be in the range of 0.7–1.4 × 10^?2 sec^?1 and 7.0 × ?2.5 × 10^?5 sec^?1. The thermotropic behavior of the polymers was studied by using polarizing optical microscopy and differential scanning calorimetry, respectively. The polymers P1 and P2 showed liquid crystalline texture characteristic of nematic phase. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Acid chloride‐functionalized hyperbranched polyester for facile and quantitative chain‐end modification: One‐pot synthesis and structure characterization

Carboxylic acid chloride end‐functionalized all‐aromatic hyperbranched polyesters were prepared from the bulk polycondensation of the AB₂ monomer 5‐(trimethylsiloxy)isophthaloyl dichloride. The acid chloride end functionality of the hyperbranched polyester was modified in situ with methanol and yielded methyl ester ends in a one‐pot process. Chain‐end functionalization and esterification were quantitative according to both potentiometric titration and ¹H NMR analysis. The signals of ¹H and ¹³C NMR spectra of the esterified hyperbranched polyester were fully assigned from model compounds of the focal, linear, dendritic, and terminal units. The degree of branching and molecular weight averages measured by ¹H and ¹³C NMR spectroscopy and multidetector size exclusion chromatography increased systematically with increasing polymerization temperatures between 80 and 200 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2855–2867, 2002     

Tuning the optical properties of hyperbranched polymers through the modification of the end groups

Dye‐capped, hyperbranched, conjugated polymers were prepared by the modification of the peripheral bromo end groups of the hyperbranched polymer core with a palladium‐catalyzed Suzuki–Miyaura cross‐coupling reaction. The dye‐modified, hyperbranched polymers had high molecular weights and displayed good solubility in common organic solvents such as tetrahydrofuran, toluene, and chloroform. The structure of the dye‐modified, hyperbranched polymers was characterized by ¹H and ¹³C NMR and elemental analysis. The thermal properties of five kinds of hyperbranched polymers were investigated with thermogravimetric analysis and differential scanning calorimetry. The optical properties of the dye‐capped, hyperbranched polymers were investigated with ultraviolet‐absorption and fluorescence spectroscopy. The hyperbranched structure could effectively reduce the aggregation of the peripheral dyes. The emission colors of the hyperbranched polymers could be easily tuned by end‐group modification. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 111–124, 2007     

Synthesis of imidazole‐terminated hyperbranched polymers with POSS‐branching points and their pH responsive and coordination properties

An imidazole‐terminated hyperbranched polymer with octafunctional POSS branching units denoted as POSS‐HYPAM‐Im was prepared by the polymerization of excess amounts of tris(2‐aminoethyl)amine with the first‐generation methyl ester‐terminated POSS‐core poly(amidoamine)‐typed dendrimer, reacting with methyl acrylate, and ester‐amide exchange reaction with 3‐aminopropylimidazole. The imidazole‐terminated hyperbranched poly(amidoamine) denoted as HYPAM‐Im was also synthesized with 1‐(3‐aminopropyl)imidazole from a methyl ester‐terminated hyperbranched poly(amidoamine) by the ester‐amide exchange reaction. The transmittance of the POSS‐HYPAM‐Im solution drastically decreased when the solution pH was greater than 8.2. On the other hand, the transmittance of the HYPAM‐Im solution gradually decreased when the solution pH at 8.5 and was greater than 9. Spectrophotometric titrations of the hyperbranched polymer aqueous solutions with Cu²⁺ ions indicated the variation of the coordination modes of POSS‐HYPAM‐Im from the Cu²⁺–N₄ complex to the Cu²⁺–N₂O₂ complex and the existence of the only one complexation mode of Cu²⁺–N₄ between Cu²⁺ ion and HYPAM‐Im with increasing the concentrations. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2695–2701     

Direct synthesis of terminally “clickable” linear and hyperbranched polyesters

1,3‐Dipolar cycloaddition of an organic azide and an acetylenic unit, often referred to as the “click reaction”, has become an important ligation tool both in the context of materials chemistry and biology. Thus, development of simple approaches to directly generate polymers that bear either an azide or an alkyne unit has gained considerable importance. We describe here a straightforward approach to directly prepare linear and hyperbranched polyesters that carry terminal propargyl groups. To achieve the former, we designed an AB‐type monomer that carries a hydroxyl group and a propargyl ester, which upon self‐condensation under standard transesterification conditions yielded a polyester that carries a single propargyl group at one of its chain‐ends. Similarly, an AB₂ type monomer that carries one hydroxyl group and two propargyl ester groups, when polymerized under the same conditions yielded a hyperbranched polymer with numerous “clickable” propargyl groups at its molecular periphery. These propargyl groups can be readily clicked with different organic azides, such as benzyl azide, ω‐azido heptaethyleneglycol monomethylether or 9‐azidomethyl anthracene. When an anthracene chromophore is clicked, the molecular weight of the linear polyester could be readily estimated using both UV–visible and fluorescence spectroscopic measurements. Furthermore, the reactive propargyl end group could also provide an opportunity to prepare block copolymers in the case of linear polyesters and to generate nanodimensional scaffolds to anchor a variety of functional units, in the case of the hyperbranched polymer. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3200–3208, 2010     

Synthesis,characterization, and electrical properties of a diazodiphenylene‐bridged Cu–phthalocyanine polymer

A diazodiphenylene‐bridged Cu–phthalocyanine polymer was synthesized from the diazonium salt of bensidine and the Cu(II) 1,8,15,22‐tetraaminophthalocyanine complex and characterized with Fourier transform infrared, ultraviolet–visible spectroscopy, and elemental analysis. The polymer was partially soluble in organic solvents such as dimethylformamide and tetrahydrofuran. The molecular weight of the soluble part of the polymer was investigated with ebullioscopy and viscosimetry methods in tetrahydrofuran. Both methods showed that the molecular weight of the polymer was much larger than that of the complex. The conductivity of the samples was measured with a four‐prop conductivity measuring device. Iodine and hydrogen chloride were doped to the polymer, and an increase of about 10⁴ S cm^?1 in the electrical conductivity was observed. The cyclic voltammogram of the diazodiphenylene‐bridged Cu–phthalocyanine polymer in contact with a LiClO₄ electrolyte exhibited two reductions and two reoxidations with high reversibility and electrochemical stability. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5692–5698, 2006     

Synthesis of hyperbranched poly(ether nitrile)s by one‐step polycondensation of an AB2 monomer

Hyperbranched poly(ether nitrile)s were prepared from a novel AB₂ type monomer, 2‐chloro‐4‐(3,5‐dihydroxyphenoxy)benzonitrile, via nucleophilic aromatic substitution. Soluble and low‐viscous hyperbranched polymers with molecular weights upto 233,600 (M_w) were isolated. According to the ¹H NMR and GPC data, the unique polymerization behavior was observed, which implies that the weight average molecular weight increased after the number average molecular weight reached plateau region. Model compounds were prepared to characterize the branching structure. Spectroscopic measurements of the model compounds and the resulting polymers, such as ¹H, DEPT ¹³C NMR, and MS, strongly suggest that the ether exchange reaction and cyclization are involved in the propagation reaction. The side reactions would affect the unique polymerization behavior. The resulting polymers showed a good solubility in organic solvents similar to other hyperbranched aromatic polymers. The hydroxy‐terminated polymer was even soluble in basic water. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5835–5844, 2009     

Synthesis and application as polymer electrolyte of hyperbranched polyether made by cationic ring‐opening polymerization of 3‐{2‐[2‐(2‐hydroxyethoxy)ethoxy]ethoxymethyl}‐3′‐methyl‐oxetane

A novel cyclic ether monomer 3‐{2‐[2‐(2‐hydroxyethoxy)ethoxy]ethoxy‐methyl}‐3′‐methyloxetane (HEMO) was prepared from the reaction of 3‐hydroxymethyl‐3′‐methyloxetane tosylate with triethylene glycol. The corresponding hyperbranched polyether (PHEMO) was synthesized using BF₃·Et₂O as initiator through cationic ring‐opening polymerization. The evidence from ¹H and ¹³C NMR analyses revealed that the hyperbranched structure is constructed by the competition between two chain propagation mechanisms, i.e. active chain end and activated monomer mechanism. The terminal structure of PHEMO with a cyclic fragment was definitely detected by MALDI‐TOF measurement. A DSC test implied that the resulting polyether has excellent segment motion performance potentially beneficial for the ion transport of polymer electrolytes. Moreover, a TGA assay showed that this hyperbranched polymer possesses high thermostability as compared to its liquid counterpart. The ion conductivity was measured to reach 5.6 × 10^?5 S/cm at room temperature and 6.3 × 10^?4 S/cm at 80 °C after doped with LiTFSI at a ratio of Li:O = 0.05, presenting the promise to meet the practical requirement of lithium ion batteries for polymer electrolytes. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3650–3665, 2006     

Photoactive liquid crystalline polymers: A comprehensive study of linear and hyperbranched polymers synthesized by A2B2, A2B3, A3B2, and A3B3 approaches

A series of linear and hyperbranched polyester epoxies, with varied structural parameters such as kinked structure and different dendritic architectures, were synthesized by A₂ + B₂, A₂ + B₃, A₃ + B₂, and A₃ + B₃ approaches. The structures of synthesized monomers and polymers were confirmed by Fourier transform infrared, ¹H NMR, and ¹³C NMR spectroscopic techniques. The effect of varied structural parameters on phase behavior and photoresponsive properties was investigated by using differential scanning calorimeter, thermal optical polarized microscope, UV–visible spectroscopy, photoviscosity, and refractive index studies. The transition temperatures of hyperbranched polymers were higher than that of the corresponding linear analogues. All the polymers showed nematic phase (nematic droplets) over a broad temperature range. The effect of kinked structural unit on photoresponsive property is less in both linear and hyperbranched architectures. Although the effect of architectural nature is highly considerable within the hyperbranched architectures, the polymer (HPE–33) synthesized by A₃ + B₃ approach showed highest rate of photocrosslinking, followed by HPE–I 32; HPE–T 32, and HPE–23, which were synthesized by A₃ + B₂ and A₂ + B₃ approaches, respectively. The findings in photoresponsive properties were further supported by molecular modeling studies. Substantial variation of refractive index (0.015–0.024) indicates that these polymers could be used for optical recording. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Design,synthesis, photophysical,and electrochemical properties of DCM‐based conjugated polymers for light‐emitting devices

A series of conjugated hyperbranched polymers, hyperbranched copolymers, and linear polymers containing 2‐pyran‐4‐ylidenemalononitrile (acceptor) and triphenylamine/fluorene (donor) units were synthesized and characterized by FTIR, ¹H NMR, thermogravimetric analyses, differential scanning calorimetry, gel permeation chromatography, UV–visible, photoluminescence, and cyclic voltammetry measurements. All the polymers show red‐light emission in the range of 566–656 nm both in solution and in solid state. The quantum efficiency of the polymers was in the range of 56–82%. Among the six polymers synthesized, only polymers containing fluorene units show T_g and polymers based on triphenylamine not exhibit T_g. The band gap of these polymers were found to be reasonably low; hyperbranched copolymer containing fluorene unit shows lowest band gap of 2.18 eV due to the stabilization of LUMO energy level by the electron withdrawing ? CN groups. The thermal and solubility behavior of the polymers were found to be good. All the EL spectra of the devices (indium‐tin oxide/poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate)/polymer/2,9‐dimethyl‐4,7‐diphenyl‐1,10‐phenanthroline/tris(8‐hydroxyquinoline)aluminum)/LiF/Al) show red‐light emission, and the device fabricated with P3 and P4 shows maximum luminance and luminous efficiency of 4104 cd m^?2 and 0.55 cd Å^?1 and 3696 cd m^?2 and 0.47 cd Å^?1, respectively, indicates that they had the best carrier balance. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Linear and A2+B3‐type hyperbranched polyesters comprising phenylbenzothiazole unit: Preparation,liquid crystalline,and optical properties

Novel liquid crystalline (LC) hyperbranched (HB) polyesters comprising phenylbenzothiazole (PBT) unit as mesogen in the interiors were prepared at various feed mole ratios (A₂/B₃) by solution polycondensation of a dioxydiundecanol derivative of PBT (A₂ monomer) with trimesic acid trimethyl ester (B₃ monomer) via A₂+B₃ approach and their LC and optical properties were investigated. Analogous linear polyesters containing the PBT unit in the main chains were also prepared by the solution polycondensation of A₂ monomer with aromatic or aliphatic dimethyl esters. FTIR and ¹H‐NMR spectroscopies indicated that the HB polyesters are produced without gelation during the polycondensation and have degree of branching (DB) of 7–46%. The structures of HB polymers changed depending on the feed mole ratios and the polymer prepared in the mole ratio of A₂/B₃ = 3/2 had the highest inherent viscosity and DB. Acetylation of terminal OH group‐having HB polyesters prepared in excess mole ratios of A₂/B₃ afforded ones bearing acetoxy groups in the terminals. DSC measurements, polarizing microscope observations of textures, and X‐ray analyses suggested that only the terminal OH group‐having HB polymer prepared in the mole ratio of A₂/B₃ = 3/1 form smectic C phase. In the linear polymers, the polymers derived by using the aromatic dimethyl esters had no LC melt, but those from the aliphatic dimethyl esters formed LC smectic C phase. The acetoxy group‐bearing HB polymers showed more stable smectic A or C phase than those with the OH terminals. Solution UV‐vis and photoluminescent (PL) spectra indicated that the linear and the HB polymers have analogous optical properties and display maximum absorbances and blue‐light emission on the basis of the PBT unit, where the Stokes shifts were observed because of intermolecular aggregation effects, but there is a large difference between the optical behaviors of the linear and the HB polymers in film, whose E_g values of the linear polymers decreased and those of the HB polymers vice versa. Quantum efficiencies (Φ) had a tendency of increase in the linear polymers and the HB polymers forming LC phases. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6688–6702, 2008     

A hyperbranched,rotaxane‐type mechanically interlocked polymer

Based on the dibenzo‐24‐crown‐8/1,2‐bis(pyridinium)ethane recognition motif, a hyperbranched mechanically interlocked polymer was prepared by polyesterification of an easily available dynamic trifunctional AB₂ pseudorotaxane monomer. It was characterized by various techniques including ¹H NMR, COSY, NOESY, GPC, viscosity, TGA, dynamic laser light scattering, AFM, and SEM. Its GPC M_n was determined to be 191 kDa with polydispersity 1.7 and its hydrodynamic diameter in a dilute solution in acetone was about 70 nm. This measured M_n value corresponds to about 93 repeating units. The study reported here presents not only a new polymer topology but also a novel and convenient way to prepare mechanically interlocked polymers. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4067–4073, 2010     

Hyperbranched copolyfluorene from a 2,4,7‐trifunctional fluorene monomer

A new hyperbranched ( P1 ) and linear copolyfluorene ( P2 ) were prepared from 2,4,7‐trifunctional (branching) and 2,7‐bifunctional fluorene monomer, respectively, by the Wittig reaction, followed with end‐capping by aromatic oxadiazole groups, to study the effect of hyperbranch structure. The weight‐average molecular weights (M_w) of P1 and P2 , determined by gel permeation chromatography using polystyrene as standard, were 33,000 and 25,700, respectively. The polymers were readily soluble in common organic solvents and exhibited good thermal stability (T_d > 400 °C). Optical properties, both in solution and film state, were investigated using absorption and photoluminescence (PL) spectra. In film state, the absorption and PL spectra peaked at 401–425 nm and 480–495 nm, respectively. The P1 showed energy funnel effect and enhanced fluorescence efficiency owing to hyperbranched structure and terminal oxadiazole groups. The HOMO and LUMO levels of P1 ( P2) , estimated from cyclic voltammograms, are ?5.34 (?5.25) eV and ?2.94 (?2.94) eV, respectively. Two‐layer polymer light‐emitting diodes devices (ITO/PEDOT/ P1 /Ca/Al) exhibited maximal luminance and luminous efficiency of 3630 cd/m² and 0.78 cd/A, respectively, which are superior to its linear counterpart P2 (598 cd/m², 0.11 cd/A). © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5541–5551, 2007     

Synthesis of a hyperbranched polythioketal with 100% degree of branching

A 100% hyperbranched polymer was successfully prepared by using 2‐[4‐(4‐mercaptobutoxy)phenoxy]‐9H‐fluoren‐9‐one as an AB₂ monomer in trifluoroacetic acid. The kinetics of the model reaction between 9‐fluorenone and 3‐mercaptopropionic acid was investigated. The reaction obeyed the second‐order kinetics, indicating that the first reaction, that is, the formation of the intermediate from 9‐fluorenone and 3‐mercaptopropionic acid, is considerably slower than the second one, that is, the reaction of the intermediate with 3‐mercaptopropionic acid. On the basis of this finding, a new monomer expected to produce a 100% branched hyperbranched polymer, 2‐[4‐(4‐mercaptobutoxy)phenoxy]‐9H‐fluoren‐9‐one, was designed and prepared. The obtained polymer was characterized by ¹H and ¹³C‐NMR spectroscopy, which confirmed that the polymer was a 100% branched hyperbranched polymer. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2689–2700, 2008     

Ionic conductivity probed in main chain liquid crystalline azobenzene polyesters

Three main chain thermotropic liquid crystalline (LC) azobenzene polymers were synthesized using the azobenzene twin molecule (P4P) having the structure Phenylazobenzene‐tetraethyleneglycol‐Phenylazobenzene as the AA monomer and diols like diethylene glycol, tetraethylene glycol (TEG), and hexaethylene glycol as the BB comonomer. Terminal ? C(O)OMe units on P4P facilitated transesterification with diols to form polyesters. All polymers exhibited stable smectic mesophases. One of the polymers, Poly(P4PTEG) was chosen to prepare composite polymer electrolytes with LiCF₃SO₃ and ionic conductivity was measured by ac impedance spectroscopy. The polymer/0.3 Li salt complex exhibited a maximum ionic conductivity in the range of 10^?5 S cm^?1 at room temperature (25 °C), which increased to 10^?4 S cm^?1 above 65 °C. The temperature dependence of ionic conductivity was compared with the phase transitions occurring in the sample and it was observed that the glass transition had a higher influence on the ionic conductivity compared to the ordered LC phase. Reversible ionic conductivity switching was observed upon irradiation of the polymer/0.3 Li salt complex with alternate UV and visible irradiation. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 629–641     

Thermoresponsive hyperbranched polymers via In Situ RAFT copolymerization of peg‐based monomethacrylate and dimethacrylate monomers

Here we report the preparation of PEG‐based thermoresponsive hyperbranched polymers via a facile in situ reversible addition‐fragmentation chain transfer (RAFT) copolymerization using bis(thiobenzoyl) disulphide to form 2‐cyanoprop‐2‐yl dithiobenzoate in situ. This novel one‐pot in situ RAFT approach was studied firstly using methyl methacrylate (MMA) monomer, then was used to prepare thermoresponsive hyperbranched polymers by copolymerization of poly(ethylene glycol) methyl ether methacrylate (PEGMEMA, M_n = 475), poly(propylene glycol) methacrylate (PPGMA, M_n = 375) and up to 30 % of ethylene glycol dimethacrylate (EGDMA) as the branching agent. The resultant PEGMEMA‐PPGMA‐EGDMA copolymers from in situ RAFT were characterized by Gel Permeation Chromatography (GPC) and ¹H‐NMR analysis. The results confirmed the copolymers with multiple methacrylate groups and hyperbranched structure as well as RAFT functional residues. These water‐soluble copolymers with tailored compositions demonstrated tuneable lower critical solution temperature (LCST) from 22 °C to 32 °C. The phase transition temperature can be further altered by post functionalization via aminolysis of RAFT agent residues in polymer chains. Moreover, it was demonstrated by rheological studies and particle size measurements that these copolymers can form either micro‐ or macro photocrosslinked gels at suitable concentrations due to the presence of multiple methacrylate groups. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3751–3761