Preparation and enhanced properties of poly(propylene)/ silica‐grafted‐hyperbranched polyester nanocomposites

A series of poly(propylene) silica‐grafted‐hyperbranched polyester nanocomposites by grafting the modified hyperbranched polyester (Boltorn? H20), possessing theoretically 50% end carboxylic groups and 50% end hydroxyl groups, which endcapped with octadecyl isocyanate (C19), onto the surface of SiO₂ particles (30 nm) through 3‐glycidoxy‐propyltrimethoxysilane (GPTS) was prepared. The effect of silica‐grafted‐modified Boltorn? H20 on the mechanical properties of polypropylene (PP) was investigated by tensile and impact tests. The morphological structure of impact fracture surface and thermal behavior of the composites were determined by scanning electron microscopy (SEM) and differential scanning calorimetry (DSC), respectively. The melt viscosity of composites was investigated by melt flow index (MFI). The obtained results showed that: (1) the modified Boltorn? H20 was successfully grafted onto the SiO₂ surface confirmed by FT‐IR and X‐ray photoelectron spectroscopy (XPS) analysis; (2) the incorporation of silica‐grafted‐modified Boltorn? H20 (3–5 wt% SiO₂) greatly enhanced the notched impact strength as well the tensile strength of the composites; (3) the incorporation of silica‐grafted‐modified Boltorn? H20 had no influence on the melting temperature and crystallinity of PP phase; (4) the MFI of PP composites increased when the silica‐grafted‐modified Boltorn? H20 particles were added compared with PP/SiO₂ or PP/SiO₂‐GPTS composites. Copyright © 2004 John Wiley & Sons, Ltd.     

Preparation of poly(styrene‐co‐acrylonitrile)‐grafted multiwalled carbon nanotubes via surface‐initiated atom transfer radical polymerization

The in situ grafting‐from approach via atom transfer radical polymerization was successfully applied to polystyrene, poly(styrene‐co‐acrylonitrile), and polyacrylonitrile grafted onto the convex surfaces of multiwalled carbon nanotubes (MWCNTs) with (2‐hydroxyethyl 2‐bromoisobutyrate) as an initiator. Thermogravimetric analysis showed that effective functionalization was achieved with the grafting approach. The grafted polymers on the MWCNT surface were characterized and confirmed with Fourier transform infrared spectroscopy and nuclear magnetic resonance. Raman and near‐infrared spectroscopy revealed that the grafting of polystyrene, poly(styrene‐co‐acrylonitrile), and polyacrylonitrile slightly affected the side‐wall structures. Field emission scanning electron microscopy showed that the carbon nanotube surface became rough because of the grafting of the polymers. Differential scanning calorimetry results indicated that the polymers grafted onto MWCNTs showed higher glass‐transition temperatures. The polymer‐grafted MWCNTs exhibited relatively good dispersibility in an organic solvent such as tetrahydrofuran. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 460–470, 2007     

Poly(styrene‐b‐tetrahydrofuran)/clay nanocomposites by mechanistic transformation

Synthesis of poly(styrene‐block‐tetrahydrofuran) (PSt‐b‐PTHF) block copolymer on the surfaces of intercalated and exfoliated silicate (clay) layers by mechanistic transformation was described. First, the polystyrene/montmorillonite (PSt/MMT) nanocomposite was synthesized by in situ atom transfer radical polymerization (ATRP) from initiator moieties immobilized within the silicate galleries of the clay particles. Transmission electron microscopy (TEM) analysis showed the existence of both intercalated and exfoliated structures in the nanocomposite. Then, the PSt‐b‐PTHF/MMT nanocomposite was prepared by mechanistic transformation from ATRP to cationic ring opening polymerization (CROP). The TGA thermogram of the PSt‐b‐PTHF/MMT nanocomposite has two decomposition stages corresponding to PTHF and PSt segments. All nanocomposites exhibit enhanced thermal stabilities compared with the virgin polymer segments. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2190–2197, 2009     

Influence of multiwall carbon nanotube on physical properties of poly(ethylene 2,6‐naphthalate) nanocomposites

Polymer nanocomposites consisting of multiwall carbon nanotube (MWCNT) and poly(ethylene 2,6‐naphthalate) (PEN) were prepared by a melt blending process in a twin‐screw extruder. The storage modulus (G′) and loss modulus (G″) of the PEN/MWCNT nanocomposites increased with increasing frequency, and this increment being more significant at low frequency. The terminal zone slope of G′ for the PEN/MWCNT nanocomposites decreased with increasing MWCNT content, and the nonterminal behavior of those was related to the dominant nanotube–nanotube interactions at higher MWCNT content, leading to the formation of the interconnected or network‐like structures of MWCNT in the polymer nanocomposites. The decrease in the slope of the plot of log G′ versus log G″ for the PEN/MWCNT nanocomposites with increasing MWCNT content suggested the changes in the microstructures of the polymer nanocomposites by incorporating MWCNT. The incorporation of very small quantity of MWCNT significantly improved the mechanical properties of the PEN/MWCNT nanocomposites. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1062–1071, 2006     

Preparation and properties of poly(vinyl alcohol)–vermiculite nanocomposites

A vermiculite (VMT) dispersion in water was blended with aqueous poly(vinyl alcohol) (PVA). The properties of the PVA–VMT nanocomposites greatly depended on the preparation procedure because of the chemical reactions and physical interactions involved. The samples were prepared in two steps to investigate the properties of the PVA–VMT nanocomposites. The VMT was first pretreated and delaminated with hydrochloric acid. The delaminated VMT was then added to the PVA solution with various mixing times. The structure and properties of the films were investigated. From X‐ray diffraction and transmission electron microscopy, the VMT layers were found to be well dispersed individually in the PVA–VMT blends. The effect of the VMT content on the thermal behavior of the PVA–VMT blends was also studied with differential scanning calorimetry. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 749–755, 2003     

Rheological properties of diblock copolymer/layered‐silicate nanocomposites

The melt‐state viscoelastic properties of nanocomposites prepared with a symmetrical polystyrene–polyisoprene block copolymer and organically modified layered silicates are examined. Nanocomposites based on three thermodynamically equivalent organically modified layered silicates, primarily differing in lateral disk diameter (d), are studied with small‐amplitude oscillatory shear. The effects of the domain structure of the ordered block copolymer and the mesoscale dispersion of the layered silicates on the rheological properties are examined via a comparison of data for the nanocomposites in the ordered and disordered states of the block copolymer. Hybrids prepared with 5 wt % organically modified fluorohectorite (d ～ 10 μm) and montmorillonite (d ～ 1 μm) demonstrate a notable decrease in the frequency dependence of the moduli at low frequencies and a significant enhancement in the complex viscosity at low frequencies in the disordered state. This behavior is understood in terms of the development of a percolated layered‐silicate network structure. However, the viscoelastic properties in the disordered state with 5 wt % organically modified laponite (d ～ 30 nm) and in the ordered state of the block copolymer for all layered silicates demonstrate only minor changes from those observed for the unfilled polymer. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1434–1443, 2002     

Nanocomposites of vinyl chloride–acrylonitrile copolymer and silica

Vinyl chloride–acrylonitrile (VC–AN) copolymer was synthesized through emulsion copolymerization. VC–AN copolymer/silica nanocomposites were prepared by solution blending of copolymer and silica in a common solvent, N,N‐dimethylformamide (DMF). The rheology studies show that the shear‐thinning behavior of the VC–AN copolymer solution becomes less distinct as nano particles are introduced. It was also found that the viscosity of the copolymer solution decreases with adding small amount of nano particles. Transmission electron microscopy observations indicate that the UV‐treated silica could disperse well in the copolymer matrix. Differential scanning calorimeter studies suggest that the presence of the silica suppresses crystallization of the AN segments in the copolymers. Because of the interactions between copolymer chains and inorganic particles, the thermal stability and mechanical strength of the VC–AN copolymers are improved considerably. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3127–3134, 2005     

Study on synthesis of poly(N‐isopropylacrylamide) grafted carbon black and temperature‐dependence conductivity of grafted carbon black/epoxy composites

Carbon black nanoparticle grafted with poly(N‐isopropylacrylamide) (CB‐g‐PNIPAAm) was synthesized by surface‐initiated atom transfer radical polymerization (SI‐ATRP). The temperature‐responsive behavior of CB‐g‐PNIPAAm was proved by temperature‐variable ¹H NMR. A temperature‐dependent conductive composite was prepared by blending CB‐g‐PNIPAAm with epoxy resin. The relationship between temperature and resistivity of the composite was studied: the composite exhibited a negative temperature coefficient (NTC) phenomenon. Possible mechanism for the NTC phenomenon was suggested. The results showed that resultant composites can be used in intelligent temperature‐switching. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1529–1535, 2008     

Mesoporous silica particles grafted with poly(ethyleneoxide‐block‐N‐vinylcaprolactam)

Mesoporous silica particles were grafted with thermoresponsive poly(ethyleneoxide‐b‐N‐vinylcaprolactam), PEO‐b‐PVCL. N‐vinylcaprolactam was first polymerized on particle surfaces using surface initiated atom transfer radical polymerization (SI‐ATRP) and then, the poly(ethyleneoxide) blocks were attached to the PVCL chain ends with click chemistry. The sizes, thermoresponsiviness, and colloidal stability of SiO₂‐PVCL and SiO₂‐PVCL‐b‐PEO particles and their aqueous dispersions were studied by scanning electron microscopy, turbidimetry, dynamic light scattering, zeta sizer, and microcalorimetry. The phase separation temperature of the PEO‐b‐PVCL grafted particles did not considerably differ from that of the SiO₂‐PVCL particles. The zeta potential of the grafted particles was close to zero at room temperature but decreased strongly upon heating. The decrease is related to the collapse of the PVCL blocks and correspondingly, the exposure of the silica surface toward the aqueous phase. The colloidal stability of the particles could be enhanced by adding PEO blocks to the chain ends of the PVCL grafts. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5012–5020     

Branched poly(styrene‐b‐tert‐butyl acrylate) and poly(styrene‐b‐acrylic acid) by ATRP from a dendritic poly(propylene imine)(NH2)64 core

With the aim of creating highly branched amphiphilic block copolymers, the primary amine end groups of the poly(propylene imine) dendrimers DAB‐dendr‐(NH₂)₈ and DAB‐dendr‐(NH₂)₆₄ were converted to 2‐bromoisobutyramide groups. Poly (styrene‐b‐tert‐butyl methacrylate) (PS‐b‐PtBMA) was synthesized by ATRP from the eight end group initiator, and poly(styrene‐b‐tert‐butyl acrylate) (PS‐b‐PtBA) was synthesized from the 64 end group initiator. The tert‐butyl groups were removed to produce poly(styrene‐b‐methacrylic acid) (PS‐b‐PMAA) and poly(styrene‐b‐acrylic acid) (PS‐b‐PAA). Comparison of size exclusion chromatography (SEC) absolute molecular weight analyses of the polystyrenes with calculated molecular weights showed that the eight end group initiator produced a polystyrene with about eight branches, and that the 64 end group initiator produced polystyrene with many fewer than 64 branches. The PS‐b‐PtBA materials also have many fewer than 64 branches. The PS‐b‐PAA samples dissolved molecularly in DMF but formed aggregates in water even at pH 10. AFM images of the PS‐b‐PtBAs spin coated from THF and DMF onto mica showed aggregates. AFM images of the PS‐b‐PAAs spin coated from various mixtures of DMF and water at pH 10 showed flat disks and worm‐like images similar to those observed with linear PS‐b‐PAAs. Use of a PS‐b‐PAA and a PS‐b‐PMAA as templates for emulsion polymerization of styrene produced latexes 100–200 nm in diameter. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4623–4634, 2007     

Viscoelastic properties of poly(ε‐caprolactone) – hydroxyapatite micro‐ and nano‐composites

Various composites have been proposed in the literature for the fabrication of bioscaffolds for bone tissue engineering. These materials include poly(ε‐caprolactone) (PCL) with hydroxyapatite (HA). Since the biomaterial acts as the medium that transfers mechanical signals from the body to the cells, the fundamental properties of the biomaterials should be characterized. Furthermore, in order to control the processing of these materials into scaffolds, the characterization of the fundamental properties is also necessary. In this study, the physical, thermal, mechanical, and viscoelastic properties of the PCL‐HA micro‐ and nano‐composites were characterized. Although the addition of filler particles increased the compressive modulus by up to 450%, the thermal and viscoelastic properties were unaffected. Furthermore, although the presence of water plasticized the polymer, the viscoelastic behavior was only minimally affected. Testing the composites under various conditions showed that the addition of HA can strengthen PCL without changing its viscoelastic response. The results found in this study can be used to further understand and approximate the time‐dependent behavior of scaffolds for bone tissue engineering. Copyright © 2012 John Wiley & Sons, Ltd.     

Mechanical properties of clay–polyimide (BTDA–ODA) nanocomposites via ODA‐modified organoclay

Clay–polyimide [3,3′, 4,4′‐benzophenone tetracarboxylic dianhydride–4,4′‐oxydianiline (BTDA–ODA)] nanocomposites were synthesized from ODA‐modified montmorillonite (organoclay) and poly(amic acid). The layered silicates of organoclay were intercalated by polyimide (BTDA–ODA), as confirmed by X‐ray diffraction and by transmission electron microscopy, and the tensile mechanical properties of the nanocomposites were measured. It was found that the modulus and the maximum stress of these organoclay/BTDA–ODA nanocomposites were much higher than those of pure BTDA–ODA: a twofold increase in the modulus and a one‐half‐fold increase in the maximum stress in the case of 7/93 organoclay–BTDA‐ODA. In addition, the elongation‐for‐break of organoclay/BTDA–ODA nanocomposites is even slightly higher than that of pure BTDA–ODA, which is a sharp contrast to that of conventional inorganics‐filled polymer composites. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2873–2878, 2000     

Phase behavior of modified montmorillonite– poly(ϵ‐caprolactone) nanocomposites

The thermal behavior and overall isothermal crystallization kinetics of a series of organophilic modified montmorillonite–poly(?‐caprolactone) nanocomposites were investigated. In general, the thermal behavior was influenced more by the type of dispersion than by the clay content. For nanocomposites in which silicate platelets were predominantly dispersed in the polymer matrix to give exfoliated structures, the thermal properties were improved with respect to those of neat poly(?‐caprolactone), whereas in those cases in which simply intercalated structures were attained, the thermal properties regularly decayed as the clay content increased. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1321–1332, 2004     

Filler‐polymer interactions of styrene and butadiene units in silica‐filled styrene–butadiene rubber compounds

Styrene–butadiene rubber (SBR) is a copolymer of styrene and butadiene, and the butadiene unit is composed of cis‐1,4‐, trans‐1,4‐, and 1,2‐components. Filler‐polymer interactions of each component of SBR in silica‐filled SBR compounds were examined by microstructure analysis of the bound and unbound rubbers. The composition ratio of butadiene and styrene units (butadiene/styrene) of the bound rubber was higher than that of the compounded rubber. Of the butadiene units, the 1,2‐component of the bound rubber was more abundant than the cis‐1,4‐ and trans‐1,4‐components. The filler‐polymer interaction of the butadiene unit with silica was stronger than that of the styrene unit, and the interaction of the 1,2‐component was stronger as compared with the others. The butadiene–styrene ratio of the bound rubber of the compounds containing the silane coupling agent was lower than for the compounds without the silane. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 577–584, 2004     

Morphology evolution of nanocomposites based on poly(phenylene sulfide)/poly(butylene terephthalate) blend

Poly(phenylene sulfide) (PPS)/poly(butylene terephthalate) (PBT) (60/40 w/w) blend nanocomposites (PPS/PBTs) were prepared by direct melt compounding of PPS, PBT, and organoclay. The morphology and rheology of PPS/PBTs were investigated using scanning electron microscope and transmission electron microscope as well as parallel plate rheometer. The intercalated clay tactoids are selectively located in the continuous PBT phase due to their nice affinity. A novel morphology evolution of the immiscible blend matrices is observed with increase of clay loadings. Small addition of clay increases the discrete PPS spherulite domain size. With increasing loading levels, the PPS phase transform to the fibrous structure and finally, to the partial laminar structure at the high loading levels, in which shows a characteristic of large‐scaled phase separation. The presence of clay, however, does not impede the coalescence of the PPS phase because the phase size increases with increasing clay loadings. The elasticity and blend ratio of two matrices are proposed as the important roles on the morphological evolution. Moreover, the laminar structure of PPS phase is very sensitive to the steady shear flow and is easy to be broken down to spherulite droplet at the low shear rate. However, high shear level is likely to facilitate the coalescence of those PPS phase and finally to phase inversion, both contributing to increases of the dynamic modulus after steady shear flow. In conclusion, the morphology of the immiscible polymer blend nanocomposites depends strongly on both the clay loadings and shear history. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1265–1279, 2008     

Templated synthesis of silver nanoparticles in amphiphilic poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) comb copolymer

In this study, poly(vinylidene fluoride‐co‐chlorotrifluoroethylene)‐graft‐poly(oxyethylene methacrylate), P(VDF‐co‐CTFE)‐g‐POEM, an amphiphilic comb copolymer with hydrophobic P(VDF‐co‐CTFE) backbone and hydrophilic POEM side chains at 73:27 wt % was synthesized. The POEM side chains were grafted from the P(VDF‐co‐CTFE) mainchain backbone via atom transfer radical polymerization (ATRP) using direct initiation of the chlorine atoms in CTFE units. Synthesis of microphase‐separated P(VDF‐co‐CTFE)‐g‐POEM comb copolymer was successful, as confirmed by nuclear magnetic resonance (¹H NMR), FTIR spectroscopy, and transmission electron microscopy (TEM). Nanocomposite films were prepared using the comb copolymer as a template film and the in situ reduction of AgCF₃SO₃ precursor to silver nanoparticles under UV irradiation. Silver nanoparticles with 4–8 nm in average size were in situ created in the solid state template film, as revealed by TEM, UV–visible spectroscopy, and wide angle X‐ray scattering (WAXS). Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) presented the selective incorporation and the in situ growth of silver nanoparticles within the hydrophilic POEM domains of microphase‐separated comb copolymer film. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 702–709, 2008     

ASAXS study of styrene‐grafted sulfonated poly(vinylidene fluoride) membranes

Small‐angle and wide‐angle X‐ray scattering and anomalous small‐angle X‐ray scattering were used to investigate proton‐conducting membranes prepared by radiation‐induced styrene grafting and sulfonation of commercial poly(vinylidene fluoride) (PVDF‐g‐PS) films. The membranes retain the lamellar and highly oriented structure of the original PVDF films even through excessive grafting and sulfonation. The sulfonate groups aggregate in the central part of the amorphous layers, where they form a weakly ordered structure that does not show any preferred orientation. This structure is suggested to be lamellar with alternate metal‐sulfonated hydrate and PVDF‐g‐PS layers. The lamellar period is 15.1 Å. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1734–1748, 2000     

Synthesis,stereocomplex crystallization and properties of poly(l‐lactide)/four‐armed star poly(d‐lactide) functionalized carbon nanotubes nanocomposites

Functionalized carbon nanotubes (F‐CNTs) were synthesized through the nucleophilic substitution reaction between four‐armed star poly(d ‐lactide) (4PDLA) and acryl chloride of carbon nanotubes and were characterized using Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy and thermogravimetric analysis. The results indicated that the 4PDLA was successfully grafted onto carbon nanotubes, and it contained 45.5 wt% of 4PDLA. Poly(l ‐lactide) (PLLA) nanocomposites with different F‐CNTs content were prepared by solution casting. Optical microscopy and scanning electron microscopy results showed that F‐CNTs were uniformly dispersed in the nanocomposites. Crystallization behavior and crystal structure of PLLA nanocomposites were investigated using differential scanning calorimetry, polarizing microscope and X‐ray diffraction. The results found that poly(lactide) stereocomplex crystal could be formed between PLLA and F‐CNTs. F‐CNTs played different roles in the process of solution casting and melting crystallization. Polarizing microscope also revealed that crystallization temperature had a significant effect on the nucleation and spherulites growth of PLLA. Thermal stability and mechanical properties of the nanocomposites were also investigated by thermogravimetric analysis, dynamic mechanical analysis and tensile testing. These results demonstrated that the addition of F‐CNTs obviously improved thermal stability and tensile strength of PLLA. The results showed that PLLA/F‐CNTs would have potential values in engineering fields. Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis of SiO2/poly(styrene‐co‐butyl acrylate) nanocomposite microspheres via miniemulsion polymerization

A series of SiO₂/poly(styrene‐co‐butyl acrylate) nanocomposite microspheres with various morphologies (e.g., multicore–shell, normal core–shell, and raspberry‐like) were synthesized via miniemulsion polymerization. The results showed that the morphology of the composite latex particles was strongly influenced by the presence or absence of the soft monomer (butyl acrylate), the particle sizes of the silica, and the emulsifier concentrations. The incorporation of the soft monomer helped in forming the multicore–shell structure. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3202–3209, 2006     

Effect of flocculated structure on rheology of poly(butylene terephthalate)/clay nanocomposites

The microstructure and rheological property of poly(butylene terephthalate) (PBT)/epoxy/montmorillonite nanocomposites (PCNs) were investigated. For the study, PCNs were prepared by melt intercalation in clay content of 4 wt % and, epoxy loadings were varied from 2 to 4 wt %. The intercalated PCNs are characterized by different techniques such as transmission electron microscopy, Fourier transform infrared and rheology. It is interesting that the percolated tactoids network in the ternary hybrids becomes insensitive to the shear deformation with the addition of epoxy in contrast to that in the sample without epoxy, which can be attributed to the formation of a flocculated structure of clay tactoids because of the chain‐extension reactions between PBT matrix and epoxy and possible hydrogen bonding. The flocculated structure has influence on the rheological behavior of the hybrids remarkably, strengthening the percolated strong‐associated‐tactoids network and reducing the percolation threshold, while not changing the strain‐scaling. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2807–2818, 2005