Preparation and electromagnetic interference shielding characteristics of novel carbon‐nanotube/siloxane/poly‐(urea urethane) nanocomposites

Poly(urea urethane) (PUU) with a poly(dimethylsiloxane) soft segment was synthesized. Different types of conductive fillers—carbon nanotube (CNT), silver‐coated carbon nanotube (CNT–Ag), and nickel‐coated carbon nanotube (CNT–Ni)—were blended with PUU to form partially conductive polymer composites. The results showed that highly conductive metals could improve the conductivity of CNTs significantly. When the filler contents were 3, 4, and 5 parts per hundred parts of resin (phr), the PUU/CNT composites possessed electromagnetic interference shielding effectiveness (SE) at 8.5, 28.4, and 26.0 dB as the electromagnetic wave frequencies were 12.3, 16.2, and 15.9 GHz, respectively. SE of the composites that contained CNT–Ni and CNT–Ag increased with the filler loading. At the same modified‐CNT loading, the CNT–Ni‐filled composites had a higher SE than those filled with CNT–Ag. Tensile stresses ranged from 5.7 to 15.6 MPa (a 177.3% increase) when the CNT concentration reached 8 phr. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 345–358, 2005     

Microstructure,electrical, and electromagnetic interference shielding properties of carbon nanotube/acrylonitrile–butadiene–styrene nanocomposites

Processing, electrical, and electromagnetic interference (EMI) shielding behaviors of carbon nanotube (CNT)/acrylonitrile–butadiene–styrene (ABS) nanocomposites were studied as function of CNT concentration. The nanocomposites were prepared by melt mixing followed by compression molding. The selective and good level of dispersion of CNT in the styrene–acrylonitrile section of the ABS polymer was found to create conductive networks in the ABS matrix at a nanofiller loading of 0.75 wt %. At this nanofiller loading, the nanocomposite electrical conductivity was 10^?5 S/m. This conductivity makes the nanocomposite suitable for electrostatic discharge protection applications. The EMI shielding effectiveness of the nanocomposites increased with the increase in nanofiller concentration. In the 100–1500 MHz frequency range, 1.1 mm thick plates made of ABS nanocomposite filled with 5 wt % CNT exhibit an EMI shielding effectiveness of 24 dB. At this shielding level, the nanocomposite is suitable for a broad range of applications. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

A review on the mechanical,electrical and EMI shielding properties of carbon nanotubes and graphene reinforced polycarbonate nanocomposites

Recently, it has been found that carbon nanotubes (CNTs) and graphene could prove to be the most promising carbonaceous fillers in polymers nanocomposites field because of their better structural and functional properties. Their uniform dispersion in polymer matrix leads to significant improvements in their several properties. This paper reviews the effect of nanofillers, ie, CNTs, derivatized CNTs, and graphene on the polycarbonate nanocomposite and its application in aerospace, automobile, sports, electronic sectors, and various industries. The comparative analysis of carbon‐based fillers on the different properties of polycarbonate nanocomposites is also included.     

Significantly enhanced electromagnetic interference shielding effectiveness of montmorillonite nanoclay and copper oxide nanoparticles based polyvinylchloride nanocomposites

In the present study, montmorillonite (MMT) nanoclay and copper oxide (CuO) nanoparticles (NPs) reinforced polyvinylchloride (PVC) based flexible nanocomposite films were prepared via solvent casting technique. Using Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Scanning electron microscopy (SEM) and thermo-gravimetric analysis (TGA), the structural, morphological and thermal properties of PVC/MMT/CuO nanocomposite films with various loadings of CuO NPs and MMT were investigated. These studies suggested that by the addition of dual nanofillers in the polymer matrix some structural modifications occurred owing to the homogenous dispersion of MMT and CuO NPs within the PVC matrix. The TGA results reveal that the addition of CuO NPs and MMT considerably improved the thermal stability of the nanocomposites. The EMI shielding effectiveness (SE) of nanocomposites was examined in the X-band (8–12 GHz) and Ku-band (12–18 GHz) frequency regions. The EMI SE values were found to be −30 dB (X-band) and −35 dB (Ku-band) for nanocomposites containing 0.3 wt% of CuO NPs and 4.7 wt% of MMT respectively while the shielding was found to be absorption dominant. These results emphasize that PVC/MMT/CuO nanocomposite films can be used as a potential EMI shielding material.     

Molecular mobility of free‐radical‐functionalized carbon‐nanotube/siloxane/poly(urea urethane) nanocomposites

Multiwalled carbon nanotubes (MWNTs) were functionalized by a free‐radical reaction of vinyltriethoxysilane and were blended with poly(urea urethane) (PUU) containing poly(dimethylsiloxane) as a soft segment. PUU was end‐capped with aminopropyltriethoxysilane (A‐silane) or phenyltriethoxysilane (P‐silane).A‐silane‐end‐capped PUU was covalently bonded to functionalized MWNTs, whereas P‐silane‐end‐capped PUU was noncovalently bonded to pristine MWNTs by a π–π interaction. Fourier transform infrared, Raman spectra, and thermogravimetric analysis confirmed the functionalization of MWNTs. The results showed that the optimal reaction time of the functionalization of MWNT was 8 h, and the organic content of the modified carbon nanotubes reached 35.22%. Solid‐state nuclear magnetic resonance and dynamic mechanical analysis were used to investigate the molecular structure and molecular mobility of the carbon‐nanotube/PUU nanocomposites. A‐silane PUU covalently bonded to MWNTs showed a considerable reduction in the molecular motion of the soft segment, which led to the glass‐transition temperature decreasing from ?117 to ?127 °C as MWNTs were incorporated. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6084–6094, 2005     

Influences of poly(lactic acid)‐grafted carbon nanotube on thermal,mechanical, and electrical properties of poly(lactic acid)

Poly(lactic acid)‐grafted multiwalled carbon nanotubes (MWNT‐g‐PLA) were prepared by the direct melt‐polycondensation of L ‐lactic acid with carboxylic acid‐functionalized MWNT (MWNT‐COOH) and then mixed with a commercially available neat PLA to prepare PLA/MWNT‐g‐PLA nanocomposites. Morphological, thermal, mechanical, and electrical characteristics of PLA/MWNT‐g‐PLA nanocomposites were investigated as a function of the MWNT content and compared with those of the neat PLA, PLA/MWNT, and PLA/MWNT‐COOH nanocomposites. It was identified from FE‐SEM images that PLA/MWNT‐g‐PLA nanocomposites exhibit good dispersion of MWNT‐g‐PLA in the PLA matrix, while PLA/MWNT and PLA/MWNT‐COOH nanocomposites display MWNT aggregates. As a result, initial moduli and tensile strengths of PLA/MWNT‐g‐PLA composites are much higher than those of neat PLA, PLA/MWNT, and PLA/MWNT‐COOH, which stems from the efficient reinforcing effect of MWNT‐g‐PLA in the PLA matrix. In addition, the crystallization rate of PLA/MWNT‐g‐PLA nanocomposites is faster than those of neat PLA, PLA/MWNT, and PLA/MWNT‐COOH, since MWNT‐g‐PLA dispersed in the PLA matrix serves efficiently as a nucleating agent. It is interesting that, unlike PLA/MWNT nanocomposites, surface resistivities of PLA/MWNT‐g‐PLA nanocomposites did not change noticeably depending on the MWNT content, demonstrating that MWNTs in PLA/MWNT‐g‐PLA are wrapped with the PLA chains of MWNT‐g‐PLA. Copyright © 2008 John Wiley & Sons, Ltd.     

Enhanced electrical and mechanical properties of multiwall carbon nanotube rubber composites

Multiwall carbon nanotube‐filled elastomers are prepared by solution blending using a sonication process. It is shown that the processing conditions have a strong effect on the composite properties especially on electrical properties, which are very sensitive to nanotube dispersion within the elastomeric matrix. The percolation threshold is seen to be shifted to a lower nanotube content than that previously reported. With regard to the unfilled elastomer, large increases in the elastic and tensile moduli are obtained with the nanotube loading, thus highlighting the potential of this type of particles as reinforcing fillers for elastomeric matrices. Raman spectroscopy under strain has been used to evaluate the strength of the polymer–filler interface. Weak interfacial interactions are deduced, but the debundling of the nanotubes and the orientational effects of the polymeric chains are observed when the composite is submitted to a uniaxial deformation. Copyright © 2012 John Wiley & Sons, Ltd.     

Effect of oxyfluorination on electromagnetic interference shielding behavior of MWCNT/PVA/PAAc composite microcapsules

Composite microcapsules of poly(vinyl alcohol)/poly(acrylic acid)/multi-walled carbon nanotubes were prepared and the electromagnetic interference shielding behavior was evaluated for the composite microcapsules. The dispersion and adhesion of multi-walled carbon nanotubes in microcapsules were improved by the surface modification through direct oxyfluorination which introduced polar groups on the multi-walled carbon nanotubes. The composite microcapsules containing the oxyfluorinated multi-walled carbon nanotubes showed significant increases in permittivity, permeability, and electromagnetic interference shielding efficiency. The electromagnetic interference shielding efficiency of composite microcapsule increased up to 51 dB mainly base on the absorption mechanism.     

Multiwalled carbon nanotube/polymer nanocomposites: Processing and properties

Nanocomposite materials were prepared with an amorphous poly(styrene‐co‐butyl acrylate) latex as a matrix with multiwalled carbon nanotubes (MWNTs) as fillers. The microstructure of the related films was observed by transmission electron microscopy, which showed that a good dispersion of MWNTs within the matrix was obtained. The linear and nonlinear mechanical behavior and the electrical properties were analyzed. Mechanical characterization showed a mechanical reinforcement effect of the MWNTs with a relatively small decrease of the elongation at break. The composite materials exhibited an elastic behavior with increasing temperature, although the matrix alone became viscous under the same conditions. The electrical conductivity of the composite filled with 3 vol % MWNTs was studied during a tensile test, which highlighted the late damage of the material. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1186–1197, 2005     

Aspect ratio effects of multi‐walled carbon nanotubes on electrical,mechanical, and thermal properties of polycarbonate/MWCNT composites

Two multi‐walled carbon nanotubes (MWCNTs) having relatively high aspect ratios of 313 and 474 with approximately the same diameter were melt mixed with polycarbonate (PC) in a twin‐screw conical micro compounder. The effects of aspect ratio on the electrical, mechanical, and thermal properties of the PC/MWCNT composites were investigated. Electrical conductivities and storage moduli of the filled samples are found to be independent of the starting aspect ratio for these high aspect ratio tubes; although the conductivities and storage moduli are still significantly higher than values of composites made with nanotubes having more commercially common aspect ratios of ～100. Transmission electron microscopy results suggest that melt‐mixing reduces these longer nanotubes to the same length, but still approximately two times longer than the length of commercially common aspect ratio tubes after melt‐mixing. Molecular weight measurements show that during melt‐mixing the longer nanotubes significantly degrade the molecular weight of the polymer as compared to very similar nanotubes with aspect ratio ～100. Because of the molecular weight reduction glass transition temperatures predictably show a large decrease with increasing nanotube concentration. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 73–83     

Synthesis of poly(urethane urea) by in situ polymerization inside stone

The first synthesis of poly(urethane urea) by in situ polymerization inside stone was successfully carried out. Poly(propylene glycol), isophorondiisocyanate, and a catalyst [tin(II) ethyl hexanoate, aluminum acetylacetonate, or zirconium acetylacetonate] were mixed with acetone in petri dishes, and tuff samples were placed in the dishes at room temperature. The effects of the comonomer ratio, catalyst, and catalyst concentration on the chemical structure of the synthesized poly(urethane urea) were investigated. The poly(urethane urea) distribution inside the tuff and the related morphology were also analyzed, as well as the reversibility of the performed treatments. Finally, the effects of the in situ polymerization polymer on the properties of the stone, such as water capillary absorption and permeability to water vapor, were assessed. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 542–552, 2005     

The mechanical and electrical properties of carbon nanotube‐grafted polyimide nanocomposites

Polyimide (PI)‐based nanocomposites containing aminophenyl functionalized multiwalled carbon nanotubes (AP‐MWCNTs) obtained through a diazonium salt reaction was successfully prepared by in situ polymerization. PI composites with different loadings of AP‐MWCNTs were fabricated by the thermal conversion of poly(amic acid) (PAA)/AP‐MWCNTs. The mechanical and electrical properties of the AP‐MWCNTs/PI composites were improved compared with those of pure PI due to the homogeneous dispersion of AP‐MWCNTs and the strong interfacial covalent bonds between AP‐MWNTs and the PI matrix. The conductivity of AP‐MWNTs/PI composites (5:95 w/w) was 9.32 × 10^?1 S/cm which was about 10¹⁵ times higher than that of Pure PI. The tensile strength and tensile modules of the AP‐MWCNTs/PI composites with 0.5 wt % of AP‐MWCNTs were increased by about 77% (316.9 ± 10.5 MPa) and 25% (8.30 ± 1.10 GPa) compared to those of pure PI, respectively. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 960–966     

Investigation of the dielectric,mechanical, and thermal properties of noncovalent functionalized MWCNTs/polyvinylidene fluoride (PVDF) composites

To improve the dispersion of multi‐walled walled carbon nanotubes (MWCNTs) and investigate the effect of dispersant for MWCNTs functionalization on the dielectric, mechanical, and thermal properties of Polyvinylidene fluoride (PVDF) composites, two different dispersants (Chitosan and TritonX‐100) with different dispersion capability and dielectric properties were used to noncovalently functionalize MWCNTs and prepare PVDF composites via solution blending. Fourier transform infrared, X‐Ray diffraction, and Raman spectroscopy indicated that TritonX‐100 and Chitosan were noncovalent functionalized successfully on the surface of MWCNTs. With the functionalization of Chitosan and TritonX‐100, the dispersion of MWCNTs changed in different extent, which was investigated by dynamic light scattering and confocal laser scan microscopy. The dielectric, mechanical, and thermal properties of PVDF composites were also improved. Meanwhile, it was also found that the dielectric properties of PVDF composites are closely related to the dielectric properties of dispersant. High dielectric constant of dispersant contributes to the grant dielectric constant of PVDF composites. The mechanical and thermal properties of MWCNTs/PVDF composites largely depend on the dispersion of MWCNTs in PVDF, interfacial interactions and the residual solvent. Copyright © 2016 John Wiley & Sons, Ltd.     

Multiwalled carbon nanotubes reinforced poly (ether‐ketone) nanocomposites: Assessment of rheological,mechanical, and electromagnetic shielding properties

This study investigates the effect of multiwalled carbon nanotubes (MWCNTs) content on rheological, mechanical, and EMI shielding properties in Ka band (26.5‐40 GHz) of poly (ether‐ketone) [PEK] prepared by melt compounding using twin screw extruder. Transmission electron microscopy (TEM) and field emission gun scanning electron microscopy (FEG‐SEM) studies were adopted to identify dispersion of nanotubes in PEK matrix. TEM and SEM images showed uniform dispersion of MWCNTs in PEK/MWCNT composites even at loading of 5 wt%. The rheological studies showed that the material experiences viscous (fluid) to elastic (solid) transition at 1 wt% loading beyond which nanotubes form continuous network throughout the matrix which in turn promotes reinforcement. Additionally, Van‐Gurp Palmen plot (phase angle vs complex modulus) and values of damping factor further confirm that the material undergoes viscous to elastic transition at 1 wt% loading. This reinforcement effect of nanotubes is reflected in enhanced mechanical properties (flexural strength and flexural modulus). Flexural strength and flexural modulus of PEK showed an increment of 17% upon incorporation of 5 wt% of MWCNTs. Total shielding effectiveness (SE_T) of −38 dB with very high shielding effectiveness due to absorption (SE_A ~ −34 dB) was observed at 5 wt% loading of MWCNTs in PEK matrix in the frequency range of 26.5‐40 GHz (Ka band).     

Synergistic effects of functionalized graphene and functionalized multi-walled carbon nanotubes on the electrical and mechanical properties of poly(ether sulfone) composites

Mixed fillers composed of functionalized graphene (f-G) and functionalized multi-walled carbon nanotubes (f-CNTs) (f-G-f-CNTs) were prepared and their synergistic effects in terms of enhancing the electrical conductivity and tensile modulus of poly(ether sulfone) (PES) composites were investigated. The results indicate that the electrical conductivity of the 5 wt% f-G-f-CNTs(W_f-G/W_f-CNTs = 1:1)/PES composite was 2.2 times higher than that of the 5 wt% f-G/PES composite and 8.9 times higher than that of the 5 wt% f-CNTs/PES composite. Moreover, the tensile modulus of the 5 wt% f-G-f-CNTs(W_f-G/W_f-CNTs = 1:1)/PES composite relative to that of the 5 wt% f-G/PES composite and 5 wt% f-CNTs/PES composite increased by 16.5% and 50.6%, respectively. Additionally, enhancements in the electrical conductivity and tensile modulus of the PES composite depended on the weight ratio of f-G and f-CNTs in the mixed fillers. The electrical conductivity and tensile modulus exhibited maximum values when the weight ratios of f-G and f-CNTs were 1:3 and 1:1, respectively. When the weight ratio of f-G and f-CNTs was fixed at 1:1, the f-G-f-CNTs(W_f-G/W_f-CNTs = 1:1)/PES composite showed a percolation threshold of 0.22 vol%, much lower than that of the f-G/PES composite.     

Synthesis,characterization and properties of multifunctional poly(arylene ether nitriles) (PEN)/CNTs/Fe3O4 nanocomposites

In this study, a novel multifunctional poly(arylene ether nitriles)(PEN)/carbon nanotubes/Fe₃O₄ nanocomposite with high tensile strength, magnetic, and electrical properties was investigated. First, we synthesized the monodisperse Fe₃O₄ nanoparticles on the surface of the multiwalled carbon nanotubes and then the hybrid material was compounded with PEN through the solution‐casting method. The SEM and TEM images indicated that the monodisperse Fe₃O₄ nanoparticles, with the diameters of 70∼80 nm, were self‐assembled along CNTs via the covalent bond method, which was confirmed by FTIR and XRD. The results of tensile properties showed that the tensile strength and modulus reached their highest values at the CNTs/Fe₃O₄ loading content of 1 wt % and both were greatly enhanced after heat treatment. Electrical conductivity of the polymer was dramatically enhanced at the low loading level of CNTs/Fe₃O₄; the electrical percolation of was in the range of 5∼8 wt % of CNTs/Fe₃O₄. The magnetic study showed that the saturation magnetization (M_s) of PEN/CNTs/Fe₃O₄ nanocomposites increased with the increase of CNTs/Fe₃O₄ loading content, and the coercive force (H_c) of the nanocomposite was independent of the CNTs/Fe₃O₄ content. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Tunable microstructures and mechanical deformation in transparent poly(urethane urea)s

Transparent poly(urethane urea) (TPUU) materials offer an avenue to enable material designs with potential to achieve simultaneous enhancements in both physical and mechanical properties. To optimize the performance required for each application, the molecular features that influence the microstructure, the glass transition temperature (T_g), the deformation mechanisms, and the mechanical deformation behavior must be understood and exploited. In this work, a comprehensive materials characterization of select model PUUs with tunable microstructures is addressed. Increasing the hard segment (HS) content increases the stiffness and flow stress levels, whereas altering the soft segment (SS) molecular weight from 2000 to 1000 g/mol leads to an enhanced phase mixing with a SS T_g shifted ～17 °K toward higher temperatures as well as broadening of the SS relaxation closer to room temperature. As a result, the 1K TPUU materials display greater rate‐dependent stiffening and strain hardening on mechanical deformation over the broad range of strain rates covered in this work (10^?3 to 10⁴ s^?1). In such case of similar urea‐based HS content, the molar content of the urethane linkages, per stoichiometric requirements, is much higher in the 1K TPUUs than the 2K TPUUs. These additional urethane moieties lead to an increase in the extent of intermolecular interactions, via hydrogen bonding between the HS and the SS, providing not only further phase mixing and stronger rate sensitivity but also provide 1K TPUUs with drastically improved barrier properties. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Effect of carbon nanotubes on mechanical and electrical properties of polyimide/carbon nanotubes nanocomposites

Multi-walled carbon nanotubes (MWNTs) reinforced polyimide nanocomposites were synthesized by in situ polymerization using 4,4′-oxydianilline, MWNTs, and pyromellitic dianhydride followed by casting, evaporation and thermal imidization. A homogeneous dispersion of chemically modified MWNTs was achieved in polyimide matrix as evidenced by scanning electron microscopy and atomic force microscopy. The incorporation of the modified MWNTs enhanced the mechanical properties of the polyimide due to the presence of strong interfacial interaction between the polymer matrix and the nanotubes in polymer composites. The resultant polyimide/MWNTs nanocomposites were electrically conductive with significant conductivity enhancement at 3 wt% MWNTs, which is favorable for many practical uses.     

Comparative study on the properties of poly(trimethylene terephthalate) ‐based nanocomposites containing multi‐walled carbon (MWCNT) and tungsten disulfide (INT‐WS2) nanotubes

Multi‐walled carbon (MWCNT) and tungsten disulfide (INT‐WS₂) nanotubes are materials with excellent mechanical properties, high electrical and thermal conductivity. These special properties make them excellent candidates for high strength and electrically conductive polymer nanocomposite applications. In this work, the possibility of the improvement of mechanical, thermal and electrical properties of poly(trimethylene terephthalate) (PTT) by the introduction of MWCNT and INT‐WS₂ nanotubes was investigated. The PTT nanocomposites with low loading of nanotubes were prepared by in situ polymerization method. Analysis of the nanocomposites' morphology carried out by SEM and TEM has confirmed that well‐dispersed nanotubes in the PTT matrix were obtained at low loading (<0.5 wt%). Thermal and thermo‐oxidative stability of nanocomposites was not affected by the presence of nanotubes in PTT matrix. Loading with INT‐WS₂ up to 0.5 wt% was insufficient to ensure electrical conductivity of PTT nanocomposite films. In the case of nanocomposites filled with MWCNT, it was found that nanotube incorporation leads to increase of electrical conductivity of PTT films by 10 orders of magnitude, approaching a value of 10^?3 S/cm at loading of 0.3 wt%. Tensile properties of amorphous and semicrystalline (annealed samples) nanocomposites were affected by the presence of nanotubes. Moreover, the increase in the brittleness of semicrystalline nanocomposites with the increase in MWCNT loading was observed, while the nanocomposites filled with INT‐WS₂ were less brittle than neat PTT. Copyright © 2016 John Wiley & Sons, Ltd.     

Morphology evolution of nanocomposites based on poly(phenylene sulfide)/poly(butylene terephthalate) blend

Poly(phenylene sulfide) (PPS)/poly(butylene terephthalate) (PBT) (60/40 w/w) blend nanocomposites (PPS/PBTs) were prepared by direct melt compounding of PPS, PBT, and organoclay. The morphology and rheology of PPS/PBTs were investigated using scanning electron microscope and transmission electron microscope as well as parallel plate rheometer. The intercalated clay tactoids are selectively located in the continuous PBT phase due to their nice affinity. A novel morphology evolution of the immiscible blend matrices is observed with increase of clay loadings. Small addition of clay increases the discrete PPS spherulite domain size. With increasing loading levels, the PPS phase transform to the fibrous structure and finally, to the partial laminar structure at the high loading levels, in which shows a characteristic of large‐scaled phase separation. The presence of clay, however, does not impede the coalescence of the PPS phase because the phase size increases with increasing clay loadings. The elasticity and blend ratio of two matrices are proposed as the important roles on the morphological evolution. Moreover, the laminar structure of PPS phase is very sensitive to the steady shear flow and is easy to be broken down to spherulite droplet at the low shear rate. However, high shear level is likely to facilitate the coalescence of those PPS phase and finally to phase inversion, both contributing to increases of the dynamic modulus after steady shear flow. In conclusion, the morphology of the immiscible polymer blend nanocomposites depends strongly on both the clay loadings and shear history. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1265–1279, 2008