Thickness of the soft layer on glassy polystyrene surfaces

The flow behavior of the near-surface region of polystyrene films was studied via the decay kinetics of imprinted corrugation gratings at elevated temperatures. The speed of the decay is the result of a balance between surface tension, on the one hand, and viscous drag, on the other. Depth profiling is possible because the penetration depth of a surface wave is proportional to its wavelength. From the dependence of the decay rate on the penetration depth one concludes that the surface region displays an increased molecular mobility. The soft surface layer has a thickness of about 20 nm. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3031–3036, 2006     

Relation between the adhesion strength and interfacial width for symmetric polystyrene bilayers

Polystyrene (PS) bilayers were prepared and were adhered at a temperature between the surface and bulk glass-transition temperatures for a given time. Then, the interfacial adhesion strength (G_L) was examined with a conventional lap-shear measurement. G_L first increased with increasing adhesion time and then reached a constant value. This result implied that the segments moved across the interface, to a certain depth, even at a temperature below the bulk glass-transition temperature. To confirm this, the interfacial evolution for the PS/deuterated PS bilayers was examined with dynamic secondary-ion mass spectrometry. The G_L value was linearly proportional to the thickness of the interfacial adhesion layer. Finally, we propose a strategy for regulating the adhesion strength based on the chain-end chemistry. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3598–3604, 2006     

Surface and interface morphology of polystyrene/poly(methyl methacrylate) thin‐film blends and bilayers

The surface and interface morphologies of polystyrene (PS)/poly(methyl methacrylate) (PMMA) thin‐film blends and bilayers were investigated by means of atomic force microscopy (AFM) and X‐ray photoelectron spectroscopy. Spin‐coating a drop of a PS solution directly onto a PMMA bottom layer from a common solvent for both polymers yielded lateral domains that exhibited a well‐defined topographical structure. Two common solvents were used in this study. The structure of the films changed progressively as the concentration of the PS solution was varied. The formation of the blend morphology could be explained by the difference in the solubility of the two polymers in the solvent and the dewetting of PS‐rich domains from the PMMA‐rich phase. Films of the PS/PMMA blend and bilayer were annealed at temperatures above their glass‐transition temperatures for up to 70 h. All samples investigated with AFM were covered with PS droplets of various size distributions. Moreover, we investigated the evolution of the annealed PS/PMMA thin‐film blend and bilayer and gave a proper explanation for the formation of a relatively complicated interface inside a larger PS droplet. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 9–21, 2006     

Surface mobility and diffusion at interfaces of polystyrene in the vicinity of the glass transition

Symmetric polydisperse (M_w = 23 × 10⁴, M_w/M_n = 2.84) and monodisperse (M_w = 21 × 10⁴, M_w/M_n < 1.05) polystyrene (PS), and asymmetric polydisperse PS/poly(2,6-dimethyl 1,4-phenylene oxide) (PPO) interfaces have been bonded in the vicinity of the glass transition temperature (T_g) of PS. In a lap-shear joint geometry, strength develops in all cases with time to the fourth power, which indicates that it is diffusion controlled. Strength developing at short times at the polydisperse PS/PS interface, at 90°C, is higher than that at the monodisperse interface, at 92°C (at T_g − 13°C in both cases), presumably due to the contribution of the low molecular weight species. The decrease of strength at the PS/PPO interface when the bonding temperature decreases from 113 to 70°C, i.e., from T_g + 10°C to T_g − 33°C of the bulk PS, indicates a high molecular mobility at the surface as compared to that in the bulk, and can be expressed by a classical diffusion equation, which is valid above T_g (of the surface layer). © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 567–572, 1998     

Molecular dynamics simulations of the effects of carbon dioxide on the interfacial bonding of polystyrene thin films

Fabrication of nanoscale polymer‐based devices, especially in biomedical applications, is a challenging process due to requirements of precise dimensions. Methods that involve elevated temperature or chemical adhesives are not practicable due to the fragility of the device components and associated deformation. To effectively fabricate devices for lab‐on‐a‐chip or drug delivery applications, a process is required that permits bonding at low temperatures. The use of carbon dioxide (CO₂) to assist the bonding process shows promise in reaching this goal. It is now well established that CO₂ can be used to depress the glass transition temperature (T_g) of a polymer, allowing bonding to occur at lower temperatures. Furthermore, it has been shown that CO₂ can preferentially soften a polymer surface, which should allow for effective bonding at temperatures even below the bulk T_g. However, the impact of this effect on bonding has not been quantified, and the optimal bonding temperature and CO₂ pressure conditions are unknown. In this study, a molecular dynamics model is used to examine the atomic scale behavior of polystyrene in an effort to develop understanding of the physical mechanisms of bonding and to quantify how the process is impacted by CO₂. The final result is the identification of a range of CO₂ pressure conditions which produce the strongest bonding between PS thin films at room temperature. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Confinement of polystyrene at interfaces: Consequences on chain orientation

The knowledge of the structure and orientation of polymer chains adsorbed at an interface could be of major importance to predict the level of interfacial interactions and adhesion that depend strongly on the properties of the interface formed between the two materials (polymer and substrate) brought into contact. In this work, we were interested to study thin films of atactic polystyrene after adsorption (spin‐coating) on two chemically different substrates (inert and OH‐grafted gold substrates). The main aim is to analyze the resulting anisotropy due to the confinement in a quasi‐bidimensional geometry, as well as to investigate the incidence of the interfacial interactions, potentially established between the polymer and the surface, on the chain organization. Our infrared spectroscopy results allowed us to access the adsorption model of polystyrene chains and to highlight the relation between chain orientation and interfacial acid–base interactions. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1268–1276, 2006     

In Situ polymerization functionalization of single‐walled carbon nanotubes with polystyrene

The in situ polymerization functionalization of single‐walled carbon nanotubes (SWNT) with polystyrene (PS) is demonstrated utilizing stabilized nanotubes reduced by dissolution of excess lithium in ammonia. Short PS chains are tethered to SWNT sidewalls to facilitate a robust compatibilization strategy for nanotube dispersion. To augment extents of functionalization, while maintaining in situ dispersion stability, the effects of multiple monomer addition steps and varied carbon to lithium ratio are studied. The developed functionalization scheme is also effective for the reductive alkylation of SWNT with dodecyl surface groups. By studying the dodecylated SWNT, the molecular weight of grafted PS chains is estimated. The discovery of a general experimental artifact has implications for all functionalization routes utilizing reduction with lithium in ammonia. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3716–3725     

Graft copolymers having hydrophobic backbone and hydrophilic branches. XI. Preparation and thermosensitive properties of polystyrene microspheres having poly (N-isopropylacrylamide) branches on their surfaces

Thermosensitive microspheres with 0.4–1.2 μm diameter consisting of a polystyrene core and poly(N-isopropylacrylamide) (polyNIPAAm) branches on their surfaces were prepared by the free radical polymerization of a polyNIPAAm macromonomer and styrene in ethanol. Electron spectroscopy for chemical analysis (ESCA) of the microsphere surface suggested that polyNIPAAm chains were favorably located on the surface of the microspheres. The morphology of the microspheres was observed by transmission electron micrograph (TEM) and the particle size of was estimated by submicron particle analyzer. The molecular weight of the polyNIPAAm macromonomer, the ratio of the macromonomer and styrene, and the polymerization temperature affected the particle size. Thermosensitive properties of polyNIPAAm-coated polystyrene microspheres were evaluated by the turbidity of their dispersion solutions and the hydrodynamic size of the miocrospheres. The transmittance in dispersion solutions changed clearly, similar to oligoNIPAAm and polyNIPAAm macromonomers. In addition, the particle size of microspheres decreased with rising temperature. These results were explained by the thermosensitivity of polyNIPAAm branches on the microsphere surface. © 1996 John Wiley & Sons, Inc.     

Interactions between a polystyrene particle and hydrophilic and hydrophobic surfaces in aqueous solutions

The interaction between a colloidal polystyrene particle mounted on an AFM cantilever and a hydrophilic and a hydrophobic surface in aqueous solution is investigated. Despite the apparent simplicity of these two types of systems a variety of different types of interactions are observed. The system containing the polystyrene particle and a hydrophilic surface shows DLVO-like interactions characteristic of forces between charged surfaces. However, when the surface is hydrophobized the interaction changes dramatically and shows evidence of a bridging air bubble being formed between the particle and the surface. For both sets of systems, plateaus of constant force in the force curves are obtained when the particle is retracted from the surface after being in contact. These events are interpreted as a number of individual polystyrene molecules that are bridging the polystyrene particle and the surface. The plateaus of constant force are expected for pulling a hydrophobic polymer in a bad (hydrophilic) solvent. The plateau heights are found to be of uniform spacing and independent of the type of surface, which suggests a model by which collapsed polymers are extended into the aqueous medium. This model is supported by a full stretching curve showing also the backbone elasticity and a stretching curve obtained in pentanol, where the plateau changes to a nonlinear force response, which is typical for a polymer in a good or neutral solvent. We suggest that these polymer bridges are important in particular for the interaction between polystyrene and the hydrophilic surface, where they to some extent counteract the long-range electrostatic repulsion.     

Graft copolymers having hydrophobic backbone and hydrophilic branches. XXIII. Particle size control of poly(ethylene glycol)-coated polystyrene nanoparticles prepared by macromonomer method

Monodisperse polymeric nanospheres, which consist of polystyrene cores and poly(ethylene glycol) (PEG) branches on their surfaces, were prepared by the dispersion copolymerization of styrene (St) with PEG macromonomers that had a methacryloyl (MMA-PEG) or p-vinylbenzyl (St-PEG) end group in various organic solvent/water media. Electron spectroscopy for chemical analysis (ESCA) of the nanosphere surfaces indicated that PEG macromonomer chains were favorably located on their surfaces. The morphologies of the nanospheres were observed via a scanning electron micrograph (SEM), and particle sizes were estimated by a submicron particle analyzer. When both the concentration of macromonomers and molecular weight were higher, small nanospheres in diameter were obtained. Larger nanospheres in diameter were obtained using macromonomers with low molecular weight at lower concentration. The functions that correlate the diameter (D_n) on different concentration units were D_n = K[St]^0.64[MMA-PEG]^{−0.53±0.01}[I]^−0.49 and D_n = K[St]^0.80[St-PEG]^{−0.69±0.01}[I]^−0.22, where [I], [St], [MMA-PEG], and [St-PEG] are initiator, styrene, MMA-PEG, and St-PEG macromonomer concentration in feed, respectively. When the reaction parameters such as the molecular weight of the macromonomers were properly chosen, the particle size could be controlled in a range from ca. 80 to 3100 nm. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2155–2166, 1999     

Acid and basic functionalities of nitrogen and carbon dioxide plasma‐treated polystyrene

The choice of plasma gas can determine the interaction between material and plasma and therefore the applications of the treated materials. Nitrogen plasma can integrate functional groups such as primary amines and carbon dioxide plasma can incorporate carboxylic groups on the surface of polymers. For specific adhesion such as bio‐adhesion, polar groups must be attached to the surface to enhance bio‐film formation but the acidic or basic character also controls the adhesion mechanism. Nitrogen and carbon dioxide plasmas are chosen to treat the surface of polystyrene and to show the effects of different functionalizations, i.e. attachment of acid or basic groups and degradation are compared in the present work. Nitrogen‐containing plasma induces mainly weak degradation at a rate of ～0.13 µg cm^?2s^?1. The roughness of the treated surface remains mostly unchanged. Functionalization leads to amino group attachment at a concentration of 1.2 sites nm^?2. We found that carbon dioxide plasma treatment shows more drastic degradation with a rate three times higher than that of nitrogen plasma and can create more functional groups (4.5 sites nm^?2) at mild plasma treatment. However, the roughness of the surface is altered. In both cases the aromatic groups are degraded through the plasma treatment (again this is more evident with the CO₂ plasma) and the induced functionalization was shown to be quick (the upper monolayer of polystyrene film can be functionalized rapidly). Copyright © 2005 John Wiley & Sons, Ltd.     

Combined effect of fibers and PTFE nanoparticles on improving the fretting wear resistance of UHMWPE‐matrix composites

Ultra‐high molecular weight polyethylene composites reinforced with carbon fibers (CF) and polytetrafluoroethylene (PTFE) were prepared. The effects of fillers on the microstructure and fretting wear behavior of composites were investigated. The results of X‐ray diffraction and scanning electron microscopy measurements indicated that the microstructure of composites were greatly changed, and the distinct interface between fillers and matrix had been formed with the incorporation of CF and PTFE. In addition, results also showed that the simultaneously filled with CF and PTFE at a proper weight fraction contributed to dramatically improving the friction reducing and wear resistance of ultra‐high molecular weight polyethylene. It can be found that there exists synergism between fillers. Copyright © 2015 John Wiley & Sons, Ltd.     

Analysis of polystyrene surface properties on thin film bonding under carbon dioxide pressure using nanoparticle embedding technique

A gold nanoparticle embedding technique is used to determine how vacuum and pressured carbon dioxide (CO₂) affect polystyrene (PS) thin film properties. The pressured CO₂ greatly increased the gold nanoparticle embedding depth, possibly due to a low cohesive energy density near the film surface. For the monodisperse PS used in this study (M_n = 214,000), two spin‐coated thin films with intimate contact can be bonded below the bulk glass transition temperature (T_g) under CO₂ pressure when the embedded depth is larger than half of the gyration radius of PS molecules. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1535–1542, 2009     

Structural anisotropy in friction‐deposited layers of polystyrene

Friction‐deposited layers of atactic polystyrene (PS) on inert and OH‐grafted gold substrates were the subject of this study to establish a relationship between the friction process and the resulting anisotropy of the transferred polymer chains. We show, by using polarization‐modulation infrared reflection‐absorption spectroscopy that the deposited PS chains involve an anisotropy in which PS main backbone is rather perpendicular to the friction support, fact that is surprising when compared with the majority of polymers where the anisotropy is along the sliding direction. Moreover, our calculation of the orientation angles revealed that PS chains are more perpendicular in the transferred layers than in spin‐coated films. This particular anisotropy is probably due to a parallel reorientation of the phenyl ring on the friction support whatever the surface chemistry is. On the other hand, this study was useful to rectify the assignment of infrared bands unclearly reported in the literature. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3272–3281, 2006     

稀土对镁合金AZ91D摩擦磨损性能的影响

研究了不同稀土含量对AZ91D镁合金摩擦磨损性能的影响，结果表明：在所研究的范围内，稀土镁合金的摩擦磨损特性明显优于基体合金，含与不含稀土镁合金的磨损速率都随载荷的增加而增加，磨损机制均发生了由轻微磨损向严重磨损的转变，稀土的加入细化了合金组织，改善了镁合金的综合性能，增强了磨损表面氧化膜的稳定性，提高了稀土镁合金的承载能力，有效地延迟了由轻微磨损向严重磨损的转变过程。     

Friction and wear behavior of PI and PTFE composites for ultrasonic motors

High‐performance polymer‐based frictional materials have become increasingly important to improve the mechanical output properties of ultrasonic motors. This study discussed the friction and wear behavior of 2 dominating frictional materials of polymer composites for ultrasonic motors, polyimide (PI), and polytetrafluoroethylene (PTFE) filled by aramid fibers (AF) and molybdenum disulfide (MoS₂). To explore the wear mechanisms, the tribo‐pair contact stress was theoretically characterized, and the interface temperature rise was numerically predicted. The predictions showed that the flash temperature on asperity tips could reach the glass transition temperature of the polymer materials. The experimental results indicated that the contact stress and sliding speed have a small effect on the friction of the PI composite but influence considerably the friction of the PTFE composite. A higher contact stress brings about a higher specific wear rate, but a higher sliding speed reduces the wear rate. Compared with AF/MoS₂/PTFE, the AF/MoS₂/PI has much better tribological performance under high loads and speeds.     

稀土/MoSi2复合材料的干摩擦磨损性能

运用M－2型摩擦磨损试验机测定了不同载荷条件下稀土／MoSi2复合材料与45钢配对件的干摩擦磨损性能，采用SEM观察了摩擦副表面的形貌和X射线分析了磨屑相组成，并探讨了其磨损机制。结果表明：稀土／MoSi2和MoSi2与45钢干摩擦时，在负荷不超过150N的范围内，其摩擦系数μ和磨损率W与负荷p间较好地满足关系式：W（或μ）＝a bp cp^2 p^3 ep^4，两种均具有优异的耐磨性能，在80－120N范围，稀土／MoSi2复合材料的磨损率比纯MoSi2材料的至少降低了65％；稀土／MoSi2材料的磨损机制主要是粘着磨损。     

Tribological properties of hydrophilic polymer brushes under wet conditions

This article demonstrates a water‐lubrication system using high‐density hydrophilic polymer brushes consisting of 2,3‐dehydroxypropyl methacrylate (DHMA), vinyl alcohol, oligo(ethylene glycol)methyl ether methacrylate, 2‐(methacryloyloxy)ethyltrimethylammonium chloride (MTAC), 3‐sulfopropyl methacrylate potassium salt (SPMK), and 2‐methacryloyloxyethyl phosphorylcholine (MPC) prepared by surface‐initiated controlled radical polymerization. Macroscopic frictional properties of brush surfaces were characterized by sliding a glass ball probe in water using a ball‐on‐plate type tribotester under the load of 0.1–0.49 N at the sliding velocity of 10^?5–10^?1 m s^?1 at 298 K. A poly(DHMA) brush showed a relatively larger friction coefficient in water, whereas the polyelectrolyte brushes, such as poly(SPMK) and poly(MPC), revealed significantly low friction coefficients below 0.02 in water and in humid air conditions. A drastic reduction in the friction coefficient of polyelectrolyte brushes in aqueous solution was observed at around 10^?3–10^?2 m s^?1 owing to the hydrodynamic lubrication effect, however, an increase in salt concentration in the aqueous solution led to the increase in the friction coefficients of poly(MTAC) and poly(SPMK) brushes. The poly(SPMK) brush showed a stable and low friction coefficient in water even after sliding over 450 friction cycles, indicating a good wear resistance of the brush film. © 2010 The Japan Chemical Journal Forum and Wiley Periodicals, Inc. Chem Rec 10: 208–216; 2010: Published online in Wiley InterScience ( www.interscience.wiley.com ) DOI 10.1002/tcr.201000001