等浓度的氯化铵和硫酸铵溶液哪个pH高

有中学化学参考资料题:0.10 mol/L的NH4Cl和(NH4)2SO4溶液哪个pH值高?这似乎是个中学生可做的简单题目,仔细考虑不是如此.如果简单地认为盐酸和硫酸都是强酸,而硫酸是二元酸,硫酸铵溶液中铵盐浓度为0.20 mol/L,那么NH4Cl溶液pH高,那是不妥的.硫酸是二元酸,第一个氢离子能完全电离,第二个氢离子部分电离,如此考虑情况怎么样呢?是不是答案发生变化?这要通过计算来说明.     

Enhanced efficiency and stability in Sn-based perovskite solar cells with secondary crystallization growth

The conversion efficiencies reported for Tin(Sn)halide-based perovskite solar cells(PSCs)fall a large gap behind those of lead halide-based PSCs,mainly because of poor film quality of the former.Here we report an efficient strategy based on a simple secondary crystallization growth(SCG)technique to improve film quality for tin halide-based PSCs by applying a series of functional amine chlorides on the perovskite surface.They were discovered to enhance the film crystallinity and suppress the oxidation of Sn²⁺remarkably,hence reduce trap state density and non-irradiative recombination in the absorber films.Furthermore,the SCG film holds the band levels matching better with carrier transport layers and herein favoring charge extraction at the device interfaces.Consequently,a champion device efficiency of 8.07% was achieved alo ng with significant enhancements in VOC and JSC,in contrast to 5.35% of the control device value.Moreover,the SCG film-based devices also exhibit superior stability comparing with the control one.This work explicitly paves a novel and general strategy for developing high performance lead-free PSCs.     

Energy level engineering of charge selective contact and halide perovskite by modulating band offset:Mechanistic insights

Mixed cation and anion based perovskites solar cells exhibited enhanced stability under outdoor conditions,however,it yielded limited power conversion efficiency when TiO₂ and Spiro-OMeTAD were employed as electron and hole transport layer(ETL/HTL)respectively.The inevitable interfacial recombination of charge carriers at ETL/perovskite and perovskite/HTL interface diminished the efficiency in planar(n-i-p)perovskite solar cells.By employing computational approach for uni-dimensional device simulator,the effect of band offset on charge recombination at both interfaces was investigated.We noted that it acquired cliff structure when the conduction band minimum of the ETL was lower than that of the perovskite,and thus maximized interfacial recombination.However,if the conduction band minimum of ETL is higher than perovskite,a spike structure is formed,which improve the performance of solar cell.An optimum value of conduction band offset allows to reach performance of 25.21%,with an open circuit voltage(VOC)of 1231 mV,a current density JSC of 24.57 mA/cm² and a fill factor of 83.28%.Additionally,we found that beyond the optimum offset value,large spike structure could decrease the performance.With an optimized energy level of Spiro-OMeTAD and the thickness of mixed-perovskite layer performance of 26.56% can be attained.Our results demonstrate a detailed understanding about the energy level tuning between the charge selective layers and perovskite and how the improvement in PV performance can be achieved by adjusting the energy level offset.     

Recent Advances of Pure Organic Room Temperature Phosphorescence Materials for Bioimaging Applications

Bioimaging,as a powerful and helpful tool,which allows people to investigate deeply within living organisms,has contributed a lot for both clinical theranostics and scientific research.Pure organic room temperature phosphorescence(RTP)materials with the unique features of ultralong luminescence lifetime and large Stokes shift,can efficiently avoid biological autofluorescence and scattered light through a time-resolved imaging modality,and thus are attracting increasing attention.This review classifies pure organic RTP materials into three categories,including small molecule RTP materials,polymer RTP materials and supramolecular RTP materials,and summarizes the recent advances of pure organic RTP materials for bioimaging applications.     

A new strategy to access Co/N co-doped carbon nanotubes as oxygen reduction reaction catalysts

Carbon nanotubes(CNTs),as one-dimensional nanomaterials,show great potential in energy conversion and storage due to their efficient electrical conductivity and mass transfer.However,the security risks,time-consuming and high cost of the preparation process hinder its further application.Here,we develop that a negative pressure rather than a following gas environment can promote the generation of cobalt and nitrogen co-doped CNTs(Co/N-CNTs) by using cobalt zeolitic imidazolate framework(ZIF-67) as a precursor,in which the negative pressure plays a key role in adjusting the size of cobalt nanoparticles and stimulating the rearragement of carbon atoms for forming CNTs.Importantly,the obtained Co/N-CNTs,with high content of pyridinic nitrogen and abundant graphitized structure,exhibit superior catalytic activity for oxygen reduction reaction(ORR) with half-wave potential(E_1/2) of 0.85 V and durability in terms of the minimum current loss(2%) after the 30,000 s test.Our development provides a new pathway for large-scale and cost-effective preparation of metal-doped CNTs for various applications.     

Stabilizing High-voltage Cathode Materials for Next-generation Li-ion Batteries

The pressing demand for high-energy/power lithium-ion batteries requires the deployment of cathode materials with higher capacity and output voltage.Despite more than ten years of research,high-voltage cathode mate-rials,such as high-voltage layered oxides,spinel LiNi0.5Mn1.5O4,and high-voltage polyanionic compounds still cannot be commercially viable due to the instabilities of standard electrolytes,cathode materials,and cathode electrolyte interphases under high-voltage operation.This paper summarizes the recent advances in addressing the surface and interface issues haunting the application of high-voltage cathode materials.The understanding of the limitations and advantages of different modification protocols will direct the future endeavours on advancing high-energy/power lithium-ion batteries.     

Suppressing trap states and energy loss by optimizing vertical phase distribution through ternary strategy in organic solar cells

Suppressing the trap-state density and the energy loss via ternary strategy was demonstrated.Favorable vertical phase distribution with donors(acceptors)accumulated(depleted)at the interface of active layer and charge extraction layer can be obtained by introducing appropriate amount of polymer acceptor N2200 into the systems of PBDB-T:IT-M and PBDB-TF:Y6.In addition,N2200 is gradiently distributed in the vertical direction in the ternary blend film.Various measurements were carried out to study the effects of N2200 on the binary systems.It was found that the optimized morphology especially in vertical direction can significantly decrease the trap state density of the binary blend films,which is beneficial for the charge transport and collection.All these features enable an obvious decrease in charge recombination in both PBDB-T:IT-M and PBDB-TF:Y6 based organic solar cells(OSCs),and power conversion efficiencies(PCEs)of 12.5%and 16.42%were obtained for the ternary OSCs,respectively.This work indicates that it is an effective method to suppress the trap state density and thus improve the device performance through ternary strategy.     

Conformational Properties of Comb-shaped Polyelectrolytes with Negatively Charged Backbone and Neutral Side Chains Studied by a Generic Coarse-grained Bead-and-Spring Model

A generic coarse-grained bead-and-spring model,mapped onto comb-shaped polycarboxylate-based(PCE)superplasticizers,is developed and studied by Langevin molecular dynamics simulations with implicit solvent and explicit counterions.The agreement on the radius of gyration of the PCEs with experiments shows that our model can be useful in studying the equilibrium sizes of PCEs in solution.The effects of ionic strength,side-chain number,and side-chain length on the conformational behavior of PCEs in solution are explored.Single-chain equilibrium properties,including the radius of gyration,end-to-end distance and persistenee length of the polymer backbone,shape-asphericity parameter,and the mean span dimension,are determined.It is found that with the increase of ionic strength,the equilibrium sizes of the polymers decrease only slightly,and a linear dependenew of the persistence length of backbone on the Debye screening length is found,in good agreement with the theory developed by Dobrynin.Increasing side-chain numbers and/or side-chain lengths increases not only the equilibrium sizes(radius of gyration and mean span)of the polymer as a whole,but also the persistence length of the backbone due to excluded volume interactions.     

Three-dimensionalization via control of laser-structuring parameters for high energy and high power lithium-ion battery under various operating conditions

Laser-structuring is an effective method to promote ion diffusion and improve the performance of lithium-ion battery(LIB)electrodes.In this work,the effects of laser structuring parameters(groove pitch and depth)on the fundamental characteristics of LIB electrode,such as interfacial area,internal resistances,material loss and electrochemical performance,are investigated,LiNi_0.5Co_0.2Mn_0.3O₂ cathodes were structured by a femtosecond laser by varying groove depth and pitch,which resulted in a material loss of 5%-14%and an increase of 140%-260%in the in terfacial area between electrode surface and electrolyte.It is shown that the importance of groove depth and pitch on the electrochemical performance(specific capacity and areal discharge capacity)of laser-structured electrode varies with current rates.Groove pitch is more im porta nt at low current rate but groove depth is at high curre nt rate.From the mapping of lithium concentration within the electrodes of varying groove depth and pitch by laser-induced breakdown spectroscopy,it is verified that the groove functions as a diffusion path for lithium ions.The ionic,electronic,and charge transfer resistances measured with symmetric and half cells showed that these internal resistances are differently affected by laser structuring parameters and the changes in porosity,ionic diffusion and electronic pathways.It is demonstrated that the laser structuring parameters for maximum electrode performance and minimum capacity loss should be determined in consideration of the main operating conditions of LIBs.     

Mesh-like vertical structures enable both high areal capacity and excellent rate capability

In order to balance electrochemical kinetics with loading level for achieving efficient energy storage with high areal capacity and good rate capability simultaneously for wearable electronics,herein,2 D meshlike vertical structures(NiCo_2 S_4@Ni(OH)_2) with a high mass loading of 2.17 mg cm^-2 and combined merits of both 1 D nanowires and 2 D nanosheets are designed for fabricating flexible hybrid supercapacitors.Particularly,the seamlessly interconnected NiCo_2 S_4 core not only provides high capacity of 287.5 μAh cm^-2 but also functions as conductive skeleton for fast electron transport;Ni(OH)_2 sheath occupying the voids in NiCo_2 S_4 meshes contributes extra capacity of 248.4 μAh cm^-2;the holey features guarantee rapid ion diffusion along and across NiCO_2 S_4@Ni(OH)_2 meshes.The resultant flexible electrode exhibits a high areal capacity of 535.9 μAh cm^-2(246.9 mAh g^-1) at 3 mA cm^-2 and outstanding rate performance with 84.7% retention at 30 mA cm^-2,suggesting efficient utilization of both NiCo_2 S_4 and Ni(OH)_2 with specific capacities approaching to their theoretical values.The flexible solid-state hybrid device based on NiCo_2 S_4@Ni(OH)_2 cathode and Fe_2 O_3 anode delivers a high energy density of 315 μWh cm^-2 at the power density of 2.14 mW cm^-2 with excellent electrochemical cycling stability.     

V2O5/SiO2催化剂的异丁烷选择氧化反应性能

 采用溶胶－凝胶法和浸渍法制备了V2O5／SiO2催化剂,并用XRD,IR,TPD和活性评价等手段对催化剂的表面构造、化学吸附性能和异丁烷选择氧化反应性能进行了研究．结果表明：催化剂表面由Lewis碱位V＝O双键的端氧和Lewis酸位V5＋构成,异丁烷分子主要通过甲基中的H双位吸附在催化剂表面的Lewis碱位上,异丁烯分子可通过甲基的H吸附在催化剂表面的Lewis碱位,也可通过C＝C双键吸附在催化剂表面的Lewis酸位上．在常压条件下,异丁烷选择氧化产物主要有异丁烯、甲基丙烯醛和甲基丙烯酸,其中深度氧化产物CO2主要由通过C＝C吸附的异丁烯继续反应生成．     

MoO3/SiO2催化剂的异丁烷选择氧化反应性能

分别采用浸渍法和溶胶－凝胶法制备了MoO3/SiO2催化剂，用XRD，TPR，IR，TPD和活性评价等手段对催化剂的影响，晶格氧活泼性，化学吸附性能和异丁烷选择氧化反应性能进行了研究。结果表明，催化剂表面由Lewis碱位Mo=M,Mo-O-Mo中的晶格氧和Lewis酸位Mo^6 构成，在MoO3/SiO2催化剂上，异丁烷主要通过甲基的H双位吸附在表面的Lewis碱位Mo=O上；在常压条件下，异丁烷选择氧化产物主要为异丁烷，甲基丙烯醛和甲基丙烯酸，其中深度氧化产物CO2主要由吸附的异丁烯继续反应生成；采用溶胶－凝胶法制备的MoO3/SiO2催化剂，可得到较高的异丁烷转化率和含氧有机物选择性。     

Mo-P-O/SiO2催化剂上的异丁烷选择氧化反应

 采用溶胶－凝胶法制备了MoO3／SiO2和Mo－P－O／SiO2催化剂，用X射线衍射、红外光谱、程序升温还原、程序升温脱附和活性评价等手段研究了催化剂的表面结构、晶格氧活泼性、化学吸附性能以及异丁烷选择氧化反应性能．结果表明，活性组分在催化剂表面分散较好；异丁烷吸附在催化剂表面Lewis碱位的MoO端氧上形成分子吸附态；MoO3／SiO2和Mo－P－O／SiO2两种催化剂对异丁烷选择氧化都有较好的选择性，将PO3－4引入到MoO3／SiO2催化剂中可提高含氧化合物的选择性     

激光促进甲醇氧化偶联表面反应的规律

用沉淀法制备了Ｌｉ３ＰＯ４、ＢｉＰＯ４和Ｌｉ３ＰＯ４、ＢｉＰＯ４三种固体表面材料,并用ＸＲＤ、ＩＲ、ＴＰＤ和激光促进表面反应（ＬＳＳＲ）等技术研究了这些固体表面上甲醇氧化偶联生成乙二醇的反应规律。实验结果表明：甲醇在固体材料表面的Ｐ＝９键上产生Ｃ－Ｈ端的分子态吸附,在表面的Ｌｅｗｉｓ酸位（金属离子）上产生解离态吸附。Ｌｉ３ＰＯ４和ＢｉＰＯ４的相互作用可促进甲醇在固体表面上的分子态吸附而抑制解离态吸     

乙烷部分氧化超细Fe－Mo－O催化剂的研究

采用溶胶-凝胶法制备了Fe－Mo－O催化剂，用XRD、TEM、BET、IR、TPR、TPD和微反等技术研究了催化剂晶体结构、表面构造、晶格氧活泼性、化学吸附和乙烷部分氧化反应性能。Fe－Mo－O复合氧化物催化剂是由超细微粒组成，微粒粒径约10 nm～20 nm，比表面积为48.1 m2/g。催化剂表面由Lewis碱位（Mo=O键的端氧和Fe－O－Mo键中的桥氧）及Lewis酸位构成。乙烷能以甲基中的H原子吸附在催化剂表面Lewis碱位Mo=O的端氧上形成分子吸附态，其部分氧化产物主要是C2H4和少量的CH3CHO。     

Direct gas-phase epoxidation of propylene to propylene oxide using air as oxidant on supported gold catalyst

Gold catalysts supported on SiO2, TiO2, TiO2-SiO2, and ZrO2-SiO2 supports were prepared by impregnating each support with a basic solution of tetrachloroauric acid. X-ray diffraction （XRD）, transmission electron microscopy （TEM）, and X-ray photoelectron spectroscopy （XPS） techniques were used to characterize their structure and surface composition. The results indicated that the size of gold particles could be controlled to below 10 nm by this method of preparation. Washing gold catalysts with water could markedly enhance the dispersion of metallic gold particles on the surface, but it could not completely remove the chloride ions left on the surface. The catalytic performance of direct vapor-phase epoxidation of propylene using air as an oxidant over these catalysts was evaluated at atmospheric pressure. The selectivity to propylene oxide （PO） was found to vary with reaction time on the stream. At the reaction conditions of atmosphere pressure, temperature 325 ℃, feed gas ratio V（C3H6）/V（O2）= 1/2, and GHSV =6000h^-1, 17.9% PO selectivity with 0.9% propylene conversion were obtained at initial 10 min for Au/SiO2 catalyst. After reacting 60 min only 8.9% PO selectivity were detected, but the propylene conversion rises to 1.4% and the main product is transferred to acrolein （72% selectivity）. Washing Au/TiO2-SiO2 and Aa/ZrO2-SiO2 samples with magnesium citrate solution could markedly enhance the activity and PO selectivity because smaller gold particles were obtained.     

CO2和CH3OH直接合成碳酸二甲酯Cu-Ni/V2O5-SiO2催化剂

采用表面反应改性法制备了V2O5 SiO2(VSiO)表面复合物 ,用等体积浸渍法制备了VSiO担载的Cu Ni双金属催化剂 ,用IR、TPD、TPSR和微反技术研究了CO2 和CH3OH在催化剂表面上的化学吸附与反应性能.结果表明,在Cu Ni/VSiO催化剂上存在着金属位Cu Ni合金、Lewis酸位Vn 和Lewis碱位V=O三类活性中心 ;CO2 在金属位和Lewis酸位协同作用下可生成CO2卧式吸附态M -(CO) -O→Vn ,此吸附态在138℃左右可解离成M -CO和V=O ;CH3OH在Lewis酸位和Lewis碱位协同作用下可形成解离吸附态V -OCH3和V -OH ;CO2 和CH3OH在Cu Ni/VSiO催化剂表面上的反应产物主要为碳酸二甲酯(DMC)、CH2O、CO和H2O ,其生成DMC的选择性在85%以上.     

CO2和CH3OH直接合成碳酸二甲酯Cu-Ni/V2O5-SiO2催化剂

采用表面反应改性法制备了Ｖ２Ｏ５－ＳｉＯ２（ＶＳｉＯ）表面复合物,用等体积浸渍法制备了ＶＳｉＯ担载的Ｃｕ－Ｎｉ双金属催化剂,用ＩＲ,ＴＰＤ,ＴＰＳＲ和微反技术研究了ＣＯ２和ＣＨ３ＯＨ在催化剂表面上的化学吸附与反应性能。结果表明,在Ｃｕ－Ｎｉ／ＶＳｉＯ催化剂上存在着金属位Ｃｕ－Ｎｉ合金,Ｌｅｗｉｓ酸位Ｖ＾ｎ＋和Ｌｅｗｉｓ碱位Ｖ＝Ｏ三类活性中心;ＣＯ２在金属位和Ｌｅｗｉｓ酸位协同作用下可生成ＣＯ２卧式     

Investigation of Mechanisms About Effects of Promoters P_2O_5,K_2O and A1_2O_3 on Oxidation of o-Xylene to Phthalic Anhydride

We succeeded in designing an effective catalyst, V2O5-P2O5-K2O/Al2O3. SiO2, by which a high yield of PA,105wt% can be gained in middle-sized industrial fluidized bed apparatus without addition of any promoting gas.The mechanisms of effects of P2O5, K2O and Al2O3 on the surface properties of V2O5 were investigated by means of TPD and XRD. And the selectivity of oxidation are explained.Addition of a great deal of P2O5 restrains the activity of donating surface oxygen from V2O5, but increases the number of sites which donate surface oxygen. Addition of K2O promotes donation of surface oxygen from V2O6, and decreases the number of sites of donating oxygen, on the other hand, addition of K|O makes the surface structure of V2O5 catalysts more stable. Coating a small amount of Al2O2 onto support, SiO2, restrains the activity of donating oxygen and increases the number of sites of donating surface oxygen from V2O5.     

ZSM-5型分子筛的表面酸性与催化活性

合成了一批不同硅铝比的HZSM－5沸石分子筛，并用CO62 ,Fe^3 离子对其进行改性，测定了它们在醛氨缩合反应合成吡啶中的活性和选择性。对照它们的NH3－TPD，吡啶吸附红外光谱，研究了催化剂的表面酸性与醛氨缩合催化活性的关系。研究表明，硅铝比较小时，HZSM－5的酸中心较多，但过多的酸中心会引发其它的裂解反应和缩合反应，从而降低催化剂的活性和选择性；当硅铝比为120左右时，催化活性达到最大，吡啶碱产率达60％；若继续增大硅铝比，则无足够的酸中心进行反应，用Co^2 ,Fe^3 离子对HZSM进行改性，其B酸中心变化不明显，L酸中心减少，对氨气的吸附能力有所下降，从而保证了适当的酸中心暴露，有利于反应，采用CoZSM-5催化剂，吡啶碱产率可达78％。