基于压缩感知的差分关联成像方案研究

关联成像可提供一种运用常规手段难以获得清晰图像的方法, 能够解决一些常规成像技术不易解决的问题, 是近些年来量子光学领域的前沿和热点之一.本文提出一种基于压缩感知的差分关联成像方案(简称, 差分压缩关联成像方案), 将高斯分布的热光源强度分布作为压缩感知的测量矩阵, 差分物体信息作为被成像物体信息, 利用差分关联成像方案的高成像信噪比和压缩感知技术的低采样次数, 通过正交匹配追踪算法, 高质量地恢复出物体信息. 并以二灰度“双缝”、“NUPT”, 多灰度Lena图和Boats图为例, 数值仿真差分压缩关联成像过程; 同时将本方案350次测量的结果与差分关联成像方案30000次测量的结果进行对比, 研究结果表明针对不同的被成像物体(二灰度“双缝”、“NUPT”, 以及多灰度Lena图和Boats图), 10次成像的均方误差平均值分别降低了97.7%, 93.9%, 92.5%和71.4%; 与压缩鬼成像方案相比, 同样测量次数条件下均方误差值对于二灰度双缝和多灰度Lena图、Boats图等目标物 体分别有50.4%, 72.9%和66.8%的降低. 差分压缩关联成像方案极大地提高了成像信噪比, 降低了成像时间. 关键词： 关联成像 差分 压缩感知 均方误差     

基于迭代的傅里叶望远镜图像重构方法

为了提高最终图像的质量,结合传统的直接重构算法和相位重构算法,提出了一种基于迭代的傅里叶望远镜图像重构方法。对反演得到的傅里叶频谱进行逆傅里叶变换得到直接重构图像,取直接重构图像的阈值图像作为相位重构算法的初始输入,通过迭代能够获得质量更高的图像。成像仿真实验结果表明,成像信噪比为50倍时,与直接重构图像相比,迭代重构图像斯特列尔比从0.82提高到0.88,峰值信噪比从17dB提高到19dB;在成像信噪比为100倍时,迭代重构图像斯特列尔比从0.89提高到0.93,峰值信噪比从20dB提高到22dB。     

关于轴向距离误差对PIE成像质量影响的研究

在对拓展重叠关联迭代引擎算法(ePIE)成像的轴向距离偏差问题进行详细分析的基础上指出,轴向距离偏差对再现图像所造成的影响在本质上和横向扫描步长误差所造成的影响完全一样;用含有位置搜索的ePIE算法进行图像重建时,轴向距离偏差所造成的影响理论上可以自动得以更正。     

关联成像目标重构的伪逆迭代降噪方法

结合伪逆关联成像和迭代去噪关联成像,提出了关联成像目标重构的伪逆迭代方法.该方法以伪逆关联成像重构结果为初始值,选取合适的与噪声干扰相关的阈值,通过迭代运算逼近实际的噪声干扰,最终抑制噪声并提高重构图像的峰值信噪比.以峰值信噪比和相关系数为衡量标准,将伪逆迭代关联成像的重构结果与差分关联成像、伪逆关联成像进行对比分析.仿真实验结果表明,伪逆迭代方法的峰值信噪比较伪逆关联成像方法、差分关联成像方法分别高出约1.0dB、3.1dB,同时其相关系数、视觉效果也有所改善,验证了该方法的有效性.     

基于非均匀快速傅里叶变换的干涉合成孔径显微算法

在频域光学相干层析(SDOCT)系统中,样品仅在焦深范围内有高横向分辨率,在焦外分辨率降低。干涉合成孔径显微术(ISAM)是一种三维图像重构算法,可以改善离焦区的图像模糊状况,达到在所有成像深度中都可以获得焦平面处横向分辨率的效果,同时可以解决SDOCT中系统的横向分辨率和成像深度之间的矛盾。介绍了ISAM重构算法的原理和适用的范围,对比分析了传统SDOCT成像算法和经过ISAM重构算法处理的成像图像结果。将非均匀快速傅里叶变换引入ISAM算法,实验结果表明该方法极大地节省了运算时间,提升了实时成像高分辨率SDOCT系统的性能。     

离焦模糊图像的维纳滤波恢复

为消除离焦误差产生的图像模糊,介绍了基于逆滤波和维纳滤波的离焦模糊图像复原方法。从光学成像原理出发,根据高斯方程计算离焦误差,建立离焦误差与光学传递函数之间的关系。讨论了离焦误差对光学成像系统传递函数的影响。通过建立线性空间不变的模糊模型,构建点扩散函数和光学传递函数,采用与模糊过程相反的处理方法进行图像复原,消除离焦误差造成的图像模糊。测试实验中,对标准样本Lena图像进行了离焦模糊处理,采用维纳滤波算法复原图像,选择不同的离焦半径和维纳滤波参数进行对比。实验结果表明:维纳滤波方法可有效消除离焦模糊;抑制噪声干扰和"振铃效应";可把图像峰值信噪比提高到6dB以上。     

基于Bootstrap方法的鬼成像系统图像信息重构不确定度估计

提出使用统计分析中的Bootstrap方法对鬼成像中图像信息重构的不确定度进行估计。仿真结果表明,Bootstrap方法估计的标准误差分布图与强度关联重构的标准误差理论计算结果一致;用标准Bootstrap方法估计的标准误差和置信区间分布能够很好地解释压缩感知算法得到的重构结果误差,并且使用相应的Bootstrap方法的变种能够更为准确地描述从原始样本中重构图像信息的偏差和绝对误差。所提方案适用于估计无真实参考图像的实际应用场景的重构图像的不确定度。     

基于卷积神经网络的深度图超分辨率重建

针对传统深度图超分辨率重建算法需要人工提取特征、计算复杂度较高且不容易得到合适表示特征的问题,提出一种基于卷积神经网络(CNN)的深度图超分辨率重建算法。该算法不需要提前对特定的任务从图像中提取具体的手工特征,而是模拟人类的视觉系统对原始深度图进行层次化的抽象处理以自主地提取特征。该算法直接进行从低分辨率深度图到高分辨率深度图的映射学习。映射由7个卷积层和1个反卷积层联合实现。卷积操作学习丰富的图像特征,而反卷积实现上采样重建高分辨率的深度图。Middlebury RGBD数据集的实验结果表明,该模型得到的峰值信噪比(PSNR)较传统双三次插值算法平均提高了2.7235dB,均方根误差(RMSE)平均降低了0.098;与经典CNN算法相比,PSNR平均提高了1.5244dB,RMSE平均降低了0.043。     

基于图像信息熵的ptychography轴向距离误差校正

在轴向距离参与运算的ptychography算法中,轴向距离误差会使重建图像变模糊并降低图像的分辨率.本文基于菲涅耳衍射理论建立了轴向距离误差模型,根据不同轴向距离误差对重构图像清晰度的影响,提出用图像信息熵确定图像最清晰时的轴向距离,并重建出清晰的ptychography图像.比较了图像能量变化、Tamura系数和图像信息熵这三种图像清晰度评价函数在轴向距离误差校正过程中的分布情况,发现它们均具有单峰性,且峰值确定的轴向距离相同.图像信息熵相比其他两种图像清晰度评价函数具有更高的灵敏性.仿真以及实验均证明了基于图像信息熵的ptychography轴向误差校正的可行性.     

基于阈值分割的并行压缩鬼成像方法

为了提高鬼成像的速度,提出了基于阈值分割的并行压缩差分鬼成像方法。首先通过设置合理的阈值筛选出涨落较为明显的数据进行采样;然后再通过并行分块降低图像维度,提高整体运算速度;最后通过压缩感知重构算法重构图像。通过对图"BUAA"的半物理仿真以及透射物体"光"的实验结果表明,与普通的二阶赝热光关联成像相比,该方法能以更少的采样次数和运行时间重构图像,可提升成像信噪比。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.