基于肠道微生物代谢产物的人结直肠癌诊断方法研究

建立气相色谱简单快速测定人粪便样品中短链脂肪酸( Short-chain fatty acids, SCFAs)的方法。粪便样品经1% HCl-75%乙醇溶液提取、高速离心,即用于GC测定。采用DB-FFAP毛细管柱(30 m ×0.25 mm ×0.25μm),升温程序洗脱(初始温度50℃保持1 min,以10℃/min升至190℃);气化室温度为250℃;载气(高纯氮)线速度为1.0 mL/min;分流比为50：1,采用氢火焰离子化检测器检测。经系统方法学验证,证实本方法简单灵敏、准确可靠。采用多元统计分析方法成功区分健康志愿者和结直肠癌患者。与健康志愿者相比,结直肠癌患者粪便中乙酸、丁酸降低较为明显,提示SCFAs特别是丁酸可成为结直肠癌诊断的潜在标志物。本方法可用于结直肠癌患者和健康志愿者粪便中SCFAs的快速测定,并有望成为一种快速筛查和诊断结直肠癌的方法。     

高效液相色谱-电喷雾离子阱串联质谱法检测芥子气经皮肤染毒SD大鼠肺中的DNA加合物

运用高效液相色谱-电喷雾离子阱串联质谱(HPLC-ESI-MS/MS)技术,建立了快速、简单、灵敏的SD大鼠肺中N7-(2-羟乙基硫代乙基)鸟嘌呤(N7-HETEG)的检测方法。以N7-苯甲基鸟嘌呤为内标,用甲醇和水为流动相进行梯度洗脱,正离子模式检测,方法的检出限(信噪比(S/N)≥10)为300 pg/mL,定量限(S/N≥20)为850 pg/mL。在300 pg/mL～1.28 μg/mL的质量浓度范围内,N7-HETEG浓度与N7-HETEG和内标的峰面积比呈良好的线性关系(线性相关系数为0.9929)。高、中、低3个添加水平的日内测定精密度(以相对标准偏差(RSD)计)和日间测定精密度均小于10%(n=7),回收率为100%～132%。对SD大鼠背部皮肤染芥子气,剂量分别为5.5、11、22和45 mg/kg,染毒4 d后检测大鼠肺脏中N7-HETEG的含量。各个不同染毒剂量下,每克组织中分别检测到（0.56±0.16）、（0.67±0.12）、（1.36±0.68）和(5.14±0.92) ng N7-HETEG, N7-HETEG的含量随着染毒剂量的增大而增大,表明N7-HETEG可用作芥子气暴露的体内生物标志物。     

全二维气相色谱-电子捕获检测器法分析土壤中毒杀芬同类物的残留

建立了全二维气相色谱-电子捕获检测器(GC× GC-μECD)检测土壤中毒杀芬同类物的分析方法.以非极性的DB- XLB(20 m×0.25 mm×0.25 μm)为第一色谱柱,中等极性的BPX-50(2 m×0.1 mm×0.1 μm)为第二色谱柱,对土壤中23种高关注毒杀芬同类物进行了分离鉴定,并采用基质曲线外标法进行定量分析.本方法在1～200,μg/L浓度范围内,毒杀芬同类物的线性相关系数(r2)均大于0.99,方法检出限(S/N=3)为0.039～0.482 μg/L,基质加标毒杀芬同类物的回收率为55％～115％,相对标准偏差(RSD)均小于30％(n=5).利用本方法对毒杀芬污染的土壤样品进行了测定,获得了较好的分离效果.     

加速溶剂萃取气相色谱质谱法测定污泥、底泥及土壤样品中的合成麝香

建立了污泥、底泥及土壤样品中7种合成麝香的分析方法.采用加速溶剂萃取(ASE)提取,经硅胶/中性氧化铝复合层析柱净化后,浓缩并定容洗脱液,用GC-SIM-MS进行检测.本方法对替代物标样荧蒽-d10的回收率为89.7%～110.9%.以六氯苯-c13为内标,7种合成麝香的线性范围为0.6～100.0 μg/kg.底泥和土壤中麝香的检出限为0.25～0.33 μg/kg(S/N=3); 污泥中的检出限为2.9～3.3 μg/kg(S/N=3).基质加标回收实验的平均回收率为83.6%～105.1%; RSD为3.2%～9.8%.本方法准确、快速,可用于实际样品的检测.     

气相色谱/氢火焰离子化检测法分析烷基化物料中的C4氟代烃

以实验室合成的氟代叔丁烷、氟代仲丁烷、氟代正丁烷为参考,建立了烷基化物料中C4氟代烃的气相色谱/氢火焰离子化检测(GC/FID)分析方法。提出了利用气相色谱/原子发射光谱(GC/AED)按元素响应的特点求算C4氟代烃在GC/FID上相对校正因子的方法。方法采用OV-225(50 m×0.25 mm i.d.×0.25 μm)和SE-54(44 m×0.22 mm i.d.×0.25 μm)串联柱为分析柱,FID为检测器,校正归一化或间接外标方法进行定量,具有重复性好、应用移植便利、操作简单等特点,对氟代叔     

气相色谱-串联质谱法测定沉积物中有机磷酸酯

比较了不同提取方法、净化方法对沉积物样品中有机磷酸酯(Organophosphate esters,OPEs)的富集、净化效果,建立了气相色谱-串联质谱法(GC-MS/MS)检测沉积物中8种OPEs的分析方法.用20 mL正己烷-丙酮混合液(1∶1,V/V)、涡流振荡+超声提取两次,Florisil固相萃取柱净化、8 mL乙酸乙酯洗脱,浓缩后将溶剂置换成正己烷,采用DB-5MS毛细管柱(30 m×0.25 mm ×0.25 μm)进行分离,质谱检测器在选择反应监测模式(SRM)下进行分析,内标法定量.结果表明,此前处理方法操作简单、溶剂耗量少;在3个添加浓度水平下,OPEs(除TEP外)的回收率在80％～ 120％之间,检出限为0.31 ～ 65 ng/L,且有良好的精密度与准确度.     

超高效液相色谱-串联质谱法同时测定鱼制品中残留的7种性激素

以电喷雾离子源(ESI)为电离源,在正离子采集模式下建立了鱼制品中7种性激素（甲基炔诺酮、甲基睾酮、丙酸睾酮、醋酸甲羟孕酮、醋酸甲地孕酮、醋酸氯地孕酮、诺龙）的超高效液相色谱-质谱/质谱(UPLC-MS/MS)检测方法。样品被酶解后用甲醇提取,提取液经氯化锌(ZnCl2)去脂、LC-C18和LC-NH2固相萃取柱净化、Waters ACQUITYTM UPLC BEH-C18色谱柱(100 mm×2.1 mm, 1.7 μm)分离,在多反应监测模式下进行UPLC-MS/MS分析。7种性激素的方法检出限(S/N=3)为0.08～0.17 μg/kg,定量限(S/N=10)为0.24～0.58 μg/kg。考察了内标法和基质匹配外标法对7种性激素进行定量的回收率与精密度: 添加水平为1, 4 μg/kg时,以内标法定量,7种性激素的平均回收率为76%～118%,相对标准偏差（RSD）为5.0%～11.3%;以基质匹配外标法定量,7种性激素的平均回收率为66%～94%,RSD为4.5%～10.7%。该结果表明两种方法均能够满足鱼制品中7种性激素的多残留检测要求。应用建立的方法对市售脱脂大黄鱼及烤鱼片进行检测,未发现7种目标违禁性激素。     

液相色谱-串联质谱法测定肉及肉制品中利谷隆及其代谢产物3,4-二氯苯胺残留

建立了液相色谱-串联质谱分析多种肉及肉制品中利谷隆及其代谢产物3,4-二氯苯胺残留的方法。样品用丙酮-乙腈(5:95, v/v)提取,冷冻去脂,经弗罗里硅土固相萃取柱净化后进行液相色谱-串联质谱检测,采用内标法定量。利谷隆及3,4-二氯苯胺在1～500 μg/L范围内呈良好的线性关系,相关系数(r)均大于0.998,方法的定量限(信噪比(S/N)＞10)为10 μg/kg,检出限(S/N＞3)为5 μg/kg。在各种肉及肉制品基质中添加低、中、高3种不同水平的利谷隆及3,4-二氯苯胺,其回收率范围分别为88.3%～101.2%和91.6%～101.6%,相对标准偏差(RSD)分别为4.8%～13.7%和4.7%～11.8%。结果表明所建立的方法可以满足肉及肉制品中利谷隆和3,4-二氯苯胺残留量的检测需要。     

高效液相色谱检测大麻中Δ9-四氢大麻酚的分析方法研究

建立了大麻毒品中主要有效成分Δ9-四氢大麻酚的液相色谱分析方法.选择甲醇作为大麻植物或大麻树脂的提取溶剂.采用岛津ODS-SP型(150 mm×4.6 mm,5μm)色谱柱作为定量方法的标准柱,紫外检测器主定量波长为210 nm,辅定量波长为195 nm或220 nm.以水-乙腈为流动相进行梯度洗脱,流速1mL/min,柱温40℃,进样量10 μL.在优化条件下,△9-四氢大麻酚在0.5～ 100.0 mg/L范围内线性良好,外标法及内标法的相关系数(r2)均大于0.99999.方法的检出限(S/N≥3.3)和定量下限(S/N≥ 10)分别为0.12 mg/L和0.40 mg/L.用该方法检测某大麻树脂样本,△9-四氢大麻酚含量的不确定度评定结果为5.32％±0.17％,k=2.实验结果表明,该方法快速、灵敏、准确、可靠,适用于大麻植物及树脂的定量测定.     

气相色谱/质谱法测定植物油中脂肪酸氯丙醇酯

采用苯基硼酸(PBA)衍生化-气相色谱/质谱(GC-MS)联用技术,建立了同时检测植物油中脂肪酸3-氯-1,2-丙二醇酯和脂肪酸2-氯-1,3-丙二醇酯(MCPD酯)的方法.对样品前处理过程中各因素进行了优化,获得了最佳条件,即称取0.1 g左右的食用油样品,加入内标后,经0.5 mL甲醇钠/甲醇(0.5 mol/L)水解1 min,中和后用3.0 mL正己烷脱脂净化两次;以0.25 mL PBA液衍生净化液后,用2.0 mL乙酸乙酯萃取衍生物3次,萃取液经氮气吹干后,用0.5 mL异辛烷溶解,离心后取上清液用GC-MS测定,内标法定量.在此条件下,样品中MCPD酯响应是德国DGF法响应的15～33倍;杂质相对去除率高达99.1％;有关方法学指标均较为理想.在MCPD酯为25～500 ng(以MCPD计)范围内,MCPD与内标峰面积的比值和浓度呈线性相关,相关系数大于0.9990.以花生油为加标基质,在250～1000 μg/kg范围内,进行3个水平的重复加标回收实验(n=6),3-MCPD酯和2-MCPD酯的加标回收率分别为81.1％～92.3％和103％～120％;相对标准偏差(RSD)分别为6.3％～12.4％和4.9％～9.4％;检出限分别为76.0和65.0 μg/kg.利用本方法测定2011年FAPAS考核样品(棕榈油)中3-MCPD酯的含量,测定值为4.01 mg/kg.结果表明,本方法灵敏度高,定量结果准确可靠,从根本上解决了仪器系统容易被污染的问题.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.