Surface functionalization of ordered mesoporous carbons--a comparative study

Hexagonally structured mesoporous carbons C15 and CMK-5 and cubically structured carbon C48 were synthesized using ordered silica SBA-15 and MCM-48 as templates and carbon precursors of different structures. The surfaces of these ordered carbons were chemically functionalized by employing an approach, in which the selected diazonium compounds were in situ generated and reacted with the carbon frameworks of the mesoporous carbons. The aromatic organic molecules containing chlorine, ester, and alkyl groups were covalently attached to the surface of these ordered mesoporous carbons. The presence of functional groups on the modified carbons was confirmed with Fourier transform infrared spectroscopy, thermogravimetric analysis, and nitrogen adsorption. The BET-specific surface area and the pore width of ordered carbons were significantly reduced, whereas the primary structure of these ordered carbons and their unit cells were intact. Basically, the density of grafted functional groups is related to the specific surface area of the sample, particularly the surface area of mesopores. The surface functionalization reaction takes place only on the external surface of carbon C15, while it occurs on both of the internal and external surface of CMK-5 carbon with the nanopipe structure. The presence of the micropores in CMK-5 carbon should be responsible for its lower grafting density because the small micropores are inaccessible in the reaction. It was also proposed that the preferred adsorption/reaction in C48 may be related to the observed unsymmetrical degradation of the XRD patterns for the functionalized C48 samples. The chemical modification process considerably reduced the primary mesopores in these ordered carbons by approximately 1-1.5 nm, affording carbons with micropores in the cases of C15 and C48, and mixed micropores and small mesopores in the case of CMK-5. A grafting density of approximately 0.9-1.5 micromol/m(2) was achieved under current research.     

In situ small angle X-ray scattering and benzene adsorption on polymer-based carbon hollow fiber membranes

The structural changes and the mechanism of benzene adsorption on microporous carbon hollow fiber membranes with different surface and pore network properties have been investigated by in situ small-angle X-ray scattering (SAXS) and benzene adsorption. Benzene adsorption measurements have been carried out in situ with SAXS alongside an adsorption/desorption isotherm cycle at 293 K with the aid of a specially constructed adsorption sample cell. In addition low-pressure C₆H₆ and high-pressure CO₂, CH₄ and N₂ adsorption isotherms have been performed. Two carbon hollow fiber membranes, both prepared by controlled pyrolysis procedures of polyimide membrane precursor, were under study. During benzene adsorption the intensity of the SAXS curves changes in a way that depends on how the pores are filled and the contrast fluctuations occur. The SAXS data have been modeled by evaluating the form factor of lamellar micropores upon filling with C₆H₆. The existence of ultra micropores within the surrounding matrix was also taken into account. The results suggest that the arrangement of the ultra micropores on the non-activated membrane is in such a way that the access of benzene to the micropores is restricted, resulting in an incomplete filling. On the other hand, the activation process generates a more accessible pore network where the micropores are completely filled.     

Morphological investigation of chemically treated poly(ethylene terephthalate)-based activated carbons

Complementary techniques, including low-temperature nitrogen adsorption and small-angle X-ray scattering (SAXS), are applied to detect the effects of surface functionalization on the morphology of activated carbon derived from poly(ethylene terephthalate) (PET). Scanning electron microscopy (SEM) is also employed as an auxiliary method to visualize the surface below the micron scale. The SEM images reveal a micron-sized ridgelike texture. Room temperature acid treatment makes the ridges become more pronounced, while treatment with boiling acid uncovers fiberlike structures of roughly 1 microm diameter. All samples display an apparent surface fractal dimension of Ds = 2.4 in the wave vector range 0.001-0.02 A(-1). Nitric acid at room temperature increases the surface oxygen content only by 3 at. %, while all the adsorption properties and structural parameters reported in this paper are virtually unaffected. Significant differences in the morphology at submicron scales appear only after boiling acid treatment. The resulting carbon remains highly microporous, but the loss of Brunauer-Emmett-Teller (BET) surface area from about 1150 to 304 m2/g is approximately 75%. In addition to the principal peak at around 8 A, fresh peaks appear in the polydisperse Horvath-Kawazoe (HK) pore size distribution owing to the burnoff of intervening walls. The average width of the slitlike pores calculated from the Dubinin-Radushkevich (DR) plot increases from 8.4 to 11 A. The minimum slit width where the applied probe molecules, that is, nitrogen and hexane, can enter increases from about 5 to about 5.4 A. The separation distance of the basic structural units is practically unchanged. When, however, this carbon is in contact with hexane, this distance expands from about 19 to 27 A. The swelling is consistent with the deformable nature of this sample also illustrated by the low-pressure hysteresis and the reduced helium density. Particular attention was paid to the surface areas derived from low-temperature nitrogen adsorption and X-ray measurements. Owing to the wide spatial range of the structures in these samples, estimates of the specific surface area of activated carbons can be substantially in error unless both upper and lower q ranges of the SAXS spectra are taken into account. Surface areas derived from the adsorption data either by the BET or the DR approaches were always below the values obtained by standard SAXS. As an example, the carbon sample functionalized at room temperature gave surface area values of 1114, 1293, and 1970 m2/g, respectively. The possibility that this difference is caused by inaccessible pores was excluded by contrast variation measurements with hexane.     

Surface area and microporosity of carbon aerogels from gas adsorption and small- and wide-angle X-ray scattering measurements

A carbon aerogel was obtained by carbonization of an organic aerogel prepared by sol-gel polymerization of resorcinol and formaldehyde in water. The carbon aerogel was then CO(2) activated at 800 degrees C to increase its surface area and widen its microporosity. Evolution of these parameters was followed by gas adsorption and small- and wide-angle X-ray scattering (SAXS and WAXS, respectively) with contrast variation by using dry and wet (immersion in benzene and m-xylene) samples. For the original carbon aerogel, the surface area, S(SAXS), obtained by SAXS, is larger than that obtained by gas adsorption (S(ads)). The values become nearly the same as the degree of activation of the carbon aerogel increases. This feature is due to the widening of the narrow microporosity in the carbon aerogel as the degree of activation is increased. In addition, WAXS results show that the short-range spatial correlations into the assemblies of hydrocarbon molecules confined inside the micropores are different from those existing in the liquid phase.     

The effect of the physical and chemical characteristics of activated carbons on the adsorption energy and affinity coefficient of Dubinin equation

The dependency of adsorption energy (E) and affinity coefficient (beta) of Dubinin equations (Dubinin-Radushkevich (DR) or Dubinin-Astakhov (DA)) on surface chemistry and porosity of activated carbons was investigated by analyzing adsorption of nitrogen, benzene, trichloroethylene (TCE), and water vapor by several surface-modified activated carbons and carbon fibers. For all studied nonpolar adsorbates, carbons with smaller average micropores showed higher adsorption energies independent of their surface chemistry. For water vapor, carbons with higher surface polarities showed higher adsorption energies due to specific adsorbate-adsorbent interactions. Adsorption energies increased with decreasing average micropore widths. betaN2,DR for different carbons were observed to vary in the 0.292-0.539 range. Carbons with higher degrees of mesoporosity had higher betaN2,DR values, while no dependency was observed between betaN2,DR and surface chemistry. A comparison of DR and DA cases indicates that: (1) the average value of betaN2,DA is considerably above the classical value of this parameter; and (2) the range of betaN2,DA values were smaller compared to betaN2,DR, despite a wide range of mesoporosity of carbons examined. Obtained beta(TCE,DR) values varied in the 0.952-1.243 range, with an average value of 1.085+/-0.083, independent of surface chemistry or porosity of activated carbons. A similar result was observed for beta(TCE,DA). betaH2O,DR values of different granular and fibrous activated carbons changed in the range of 0.081-0.271. They depended more on the carbon surface chemistry and less on the porosity. A similar result was obtained when DA equation was considered.     

Surface modification of activated carbon and fullerene black by Diels–Alder reaction

Activated carbon and fullerene black react with cyclopentadiene at room temperature or slightly elevated temperature. At higher temperature a retro-Diels–Alder reaction takes place. The reaction with the diene and the retro-Diels–Alder reaction could be repeated. As a consequence of the reaction with cyclopentadiene or other suitable dienes and the retro reaction, the surface structure of different carbons changed considerably. The surface area of micropores on fullerene black was much higher than for the original sample. The influence on the surface area of porosity is reported for two different types of carbon.     

Interaction of phenol and dopamine with commercial MWCNTs

We report the adsorption of phenol and dopamine probe molecules, from aqueous solution with NaCl, on commercial multiwall carbon nanotubes (MWCNT) and on their carboxylated derivative. The nanotubes were fully characterized by high resolution transmission electron microscopy (HRTEM), small angle X-ray scattering (SAXS), potentiometric titration, electrophoretic mobility, and nitrogen adsorption (77K) measurements. The experimental pollutant isotherms, evaluated using the Langmuir model, showed that only 8-12% and 21-32% of the BET surface area was available for phenol and dopamine, respectively, which is far below the performance of activated carbons. Influence of the pH was more pronounced for the oxidized MWCNT, particularly with dopamine. The strongest interaction and the highest adsorption capacity occurred at pH 3 with both model pollutants on both types of nanotubes. Although the surface area available for adsorption is far lower in MWCNTs than in activated carbons, it is nonetheless substantial. In particular, delayed release of toxic molecules that are either adsorbed on the surface or trapped in the inner bore of such systems could constitute an environmental hazard. The need for further adsorption studies with regard to their environmental aspects is therefore pressing, particularly for MWCNTs in their functionalized state.     

Enhanced hydrogen storage capacity of high surface area zeolite-like carbon materials

We report the synthesis of zeolite-like carbon materials that exhibit well-resolved powder XRD patterns and very high surface area. The zeolite-like carbons are prepared via chemical vapor deposition (CVD) at 800 or 850 degrees C using zeolite beta as solid template and acetonitrile as carbon precursor. The zeolite-like structural ordering of the carbon materials is indicated by powder XRD patterns with at least two well-resolved diffraction peaks and TEM images that reveal well-ordered micropore channels. The carbons possess surface area of up to 3200 m2/g and pore volume of up to 2.41 cm3/g. A significant proportion of the porosity in the carbons (up to 76% and 56% for surface area and pore volume, respectively) is from micropores. Both TEM and nitrogen sorption data indicate that porosity is dominated by pores of size 0.6-0.8 nm. The carbon materials exhibit enhanced (and reversible) hydrogen storage capacity, with measured uptake of up to 6.9 wt % and estimated maximum of 8.33 wt % at -196 degrees C and 20 bar. At 1 bar, hydrogen uptake capacity as high as 2.6 wt % is achieved. Isosteric heat of adsorption of 8.2 kJ/mol indicates a favorable interaction between hydrogen and the surface of the carbons. The hydrogen uptake capacity observed for the zeolite-like carbon materials is among the highest ever reported for carbon (activated carbon, mesoporous carbon, CNTs) or any other (MOFs, zeolites) porous material.     

On the mechanisms of phenol adsorption by carbons

The removal of phenol and related compounds from dilute aqueous solutions by activated carbons corresponds to the coating of the micropore walls and of the external surface by a monolayer. This process is described by an analog of the Dubinin—Radushkevich—Kaganer equation. On the other hand, as suggested by immersion calorimetry at 293 K, in the case of concentrated solutions, the mechanism corresponds to the volume filling of the micropores, as observed for the adsorption of phenol from the vapor phase. The equilibrium is described by the Dubinin—Astakhov equation. It follows that the removal of phenol from mixtures with water depends on the relative concentrations, and the limiting factor for adsorption is either the effective surface area of the carbon, or the micropore volume.     

Negative thermal expansion of water in hydrophobic nanospaces

The density and intermolecular structure of water in carbon micropores (w = 1.36 nm) are investigated by small-angle X-ray scattering (SAXS) and X-ray diffraction (XRD) measurements between 20 K and 298 K. The SAXS results suggest that the density of the water in the micropores increased with increasing temperature over a wide temperature range (20-277 K). The density changed by 10%, which is comparable to the density change of 7% between bulk ice (I(c)) at 20 K and water at 277 K. The results of XRD at low temperatures (less than 200 K) show that the water forms the cubic ice (I(c)) structure, although its peak shape and radial distribution functions changed continuously to those of a liquid-like structure with increasing temperature. The SAXS and XRD results both showed that the water in the hydrophobic nanospaces had no phase transition point. The continuous structural change from ice I(c) to liquid with increasing temperature suggests that water shows negative thermal expansion over a wide temperature range in hydrophobic nanospaces. The combination of XRD and SAXS measurements makes it possible to describe confined systems in nanospaces with intermolecular structure and density of adsorbed molecular assemblies.     

Mesoporous Carbons of Well-Organized Structure in the Removal of Dyes from Aqueous Solutions

Mesoporous carbons with differentiated properties were synthesized by using the method of impregnation of mesoporous well-organized silicas. The obtained carbonaceous materials and microporous activated carbon were investigated by applying different methods in order to determine their structural, surface and adsorption properties towards selected dyes from aqueous solutions. In order to verify applicability of adsorbents for removing dyes the equilibrium and kinetic experimental data were measured and analyzed by applying various equations and models. The structural and acid-base properties of the investigated carbons were evaluated by Small-Angle X-ray Scattering (SAXS) technique, adsorption/desorption of nitrogen, potentiometric titration, and Transmission Electron Microscopy (TEM). The results of these techniques are complementary, indicating the type of porosity and structural ordering, e.g., the pore sizes determined from the SAXS data are in good agreement with those obtained from nitrogen sorption data. The SAXS and TEM data confirm the regularity of mesoporous carbon structure. The adsorption experiment, especially kinetic measurements, reveals the utility of mesoporous carbons in dye removing, taking into account not only the adsorption uptake but also the adsorption rate.     

Surface morphology of nanostructured polymer-based activated carbons

Complementary techniques, including nitrogen adsorption, small-angle X-ray scattering (SAXS), and atomic force microscopy (AFM), have been utilized to characterize the surface features of highly microporous carbon materials prepared from highly aromatic polymers. Nitrogen adsorption measurement interpreted by BET, DR, HK, and NLDFT methods reveals these nanostructured activated carbons exhibit a high surface area of up to 4000 m2/g, a micropore volume up to approximately 1.75 mL/g, and an average pore size of approximately 10-20 angstroms. A modified equation, based on Porod's law, the Debye-Bueche equation, and fractal dimension theories, has been proposed and successfully applied to analyze the SAXS spectra and to extract the porous texture of these unique activated carbons. AFM 3D imaging combined with the Fourier transform technique has been applied to statistically quantify pore sizes on the carbon surface.     

CO2 adsorption by activated templated carbons

Highly porous carbons have been prepared by the chemical activation of two mesoporous carbons obtained by using hexagonal- (SBA-15) and cubic (KIT-6)-ordered mesostructured silica as hard templates. These materials were investigated as sorbents for CO(2) capture. The activation process was carried out with KOH at different temperatures in the 600-800°C range. Textural characterization of these activated carbons shows that they have a dual porosity made up of mesopores derived from the templated carbons and micropores generated during the chemical activation step. As a result of the activation process, there is an increase in the surface area and pore volume from 1020 m(2)g(-1) and 0.91 cm(3)g(-1) for the CMK-8 carbon to a maximum of 2660 m(2)g(-1) and 1.38 cm(3)g(-1) for a sample activated at 800°C (KOH/CMK-8 mass ratio of 4). Irrespective of the type of templated carbon used as precursor or the operational conditions used for the synthesis, the activated samples exhibit similar CO(2) uptake capacities, of around 3.2 mmol CO(2)g(-1) at 25°C. The CO(2) capture capacity seems to depend on the presence of narrow micropores (<1 nm) rather than on the surface area or pore volume of activated carbons. Furthermore, it was found that these porous carbons exhibit a high CO(2) adsorption rate, a good selectivity for CO(2)-N(2) separation and they can be easily regenerated.     

由微孔棒状羟基磷灰石为模板合成的新型层次孔炭材料的电化学电容性能

电化学电容器已经成为极具潜力的可满足高功率需求的储能系统器件. 多孔炭具有大比表面积、高导电性、化学惰性、廉价及可调孔结构等优势, 因此成为电化学电容器最为常用的电极材料. 本文报道由微孔棒状羟基磷灰石为模板及蔗糖为碳源合成的新型具有层次孔道结构的孔炭材料的电化学电容器的性能. 采用X射线衍射分析仪、扫描电子显微镜、透射电子显微镜、X射线光电子能谱及BET表面分析仪表征了合成的多孔炭的形貌及表面特性. 采用循环伏安法、交流阻抗图谱分析及恒流充放电评价多孔炭材料在1 mol·L^-1硫酸中的电化学电容性能. 多孔炭具有高的比表面积(719.7 m²·g^-1)和大的孔容(1.32 cm³·g^-1), 其无序的孔道由任意分布的微孔、坍塌的中孔及类模板形状的相互交织的棒状中孔组成. 随着炭化温度的增加, 微孔及棒状中孔的密度随之降低, 在炭化温度高达900℃时, 孔径分布图上出现了三个峰. 正是由于这些特殊的结构特征, 由900℃炭化得到的多孔炭制成的电极展示出很好的电化学电容性能.     

Carbon materials as electrodes for electrosorption of NaCl in aqueous solutions

Different porous carbons (MWCNT, a carbon aerogel, an activated carbon cloth and a chemically activated carbon) were evaluated as electrode material for the electrosorption of NaCl. The results obtained from the chronoamperometric experiments were correlated to the surface area and the size of the pores present in each carbon. These results indicate that all the surfaces are equivalent for the electrosorption process, demonstrating that both, mesopores and micropores, are equally effective. Nevertheless, the kinetics of the process is influenced by the pore size distribution of the carbon, although it is rather fast for all the carbons studied. The chemically activated carbon seems to be the most suitable carbon material for electrosorption of NaCl due to the combination of a high surface area and an appropriate pore size distribution.     

Prediction of the micropore structure parameters and adsorption properties of activated carbons

A regularity govering variations of volume and linear size of micropores in carbon adsorbents during their vapor-gas activation was found. A parameter was proposed that characterizes the degree of development of the micropore system in activating carbons and an initial carbonized material. The parameter is defined as the number (or surface area) of micropores in the volume unit of the micropore zones. This parameter allows one to rationalize the choice of carbonized materials for the preparation of activated carbons with specified adsorption properties and to establish the range of activation beyond which the structure of the micropores loses stability. Furthermore, the parameter serves to predict how activation affects micropore structure parameters and adsorption properties of carbons. This in turn indicates the optimal degrees of microporosity of carbons needed to attain required adsorption properties.     

A simple method to prepare high surface area activated carbon from carboxyl methyl cellulose by low temperature physical activation

Activated carbon with high surface area was prepared from sodium salt of carboxyl methyl cellulose by physical activation at 400 °C followed by treatment in boiling water. The carbon was characterized by XRD, SEM, EPR, TG, IR, surface areas and porosity measurements. The carbon showed alkaline reaction in aqueous solution. It showed high surface area and pore volume in comparison to two commercially available carbons.     

Cluster-Mediated Water Adsorption on Carbon Nanopores

The adsorption isotherms of water at 303 K and N2 at 77 K on various kinds of porous carbons were compared with each other. The saturated amounts of water adsorbed on carbons almost coincided with amounts of N2 adsorption in micropores. Although carbon aerogel samples have mesopores of the great pore volume, the saturated amount of adsorbed water was close to the micropore volume which is much small than the mesopore volume. These adsorption data on carbon aerogels indicated that the water molecules are not adsorbed in mesopores, but in micropores only. The adsorption isotherms of water on activated carbon having micropores of smaller than 0.7 nm in width had no clear adsorption hysteresis, while the water adsorption isotherms on micropores of greater than 0.7 nm had a remarkable adsorption hysteresis above P/P0 = 0.5. The disappearance of the clear hysteresis for smaller micropores suggested that the cluster of water molecules of about 0.7 nm in size gives rise to the water adsorption on the hydrophobic micropores; the formation and the structure of clusters of water molecules were associated with the adsorption mechanism. The cluster-mediated pore filling mechanism was proposed with a special relevance to the evidence on the formation of the ordered water molecular assembly in the carbon micropores by in situ X-ray diffraction.     

多孔碳材料的化学气相后处理及其超级电容性能

以廉价的椰壳为原料制备了高比表面积的多孔碳材料,然后在密闭的反应釜中以硝酸蒸汽对多孔碳材料进行了后处理,制备了亲水性更好的多孔碳材料。采用扫描透射电子显微镜(TEM)、物理吸附、X射线粉末衍射(XRD)、拉曼光谱(Raman)和接触角测试对材料的微观形貌、孔道结构、组成和亲水性进行了表征,探究了不同温度下硝酸蒸汽对多孔碳材料的形貌、结构的影响,并采用循环伏安法、恒电流充放电法和交流阻抗法考察了多孔碳材料的超级电容性能。结果表明,经过硝酸蒸汽处理后的多孔碳材料的比表面积和孔体积均有所降低,且随着处理温度的升高,降低得更加明显,而亲水性却越来越好。电化学测试结果表明,经过100℃硝酸蒸汽处理的多孔碳材料(CSC-100)具有最佳的超级电容性能。在以6 mol·L^-1 KOH为电解液的三电极体系中,当电流密度为0.5 A·g^-1时CSC-100的比电容可达452.9 F·g^-1,而未经硝酸蒸汽处理的多孔碳材料(CSC)的比电容仅为350.4 F·g^-1。电容贡献分析表明CSC-100良好的亲水性和表面官能团不仅提高了双电层电容,也提高了赝电容。     

A Study of the Influence of Hydrophobicity of Activated Carbon on the Adsorption Equilibrium of Aromatics in Non-Aqueous Media

The effect of hydrophobicity on the adsorption of aromatics on metal-free activated carbons was studied. Adsorption isotherms for phenol, aniline, benzene, and xylene were generated in cyclohexane and heptane media, using seven carbons with different surface heterogeneity. The hydrophobicity of these carbons was probed using flow microcalorimetry (FMC). Surface polarity and solvent and adsorbate hydrophobicity were found to influence the adsorption capacity. For adsorbates that do not form hydrogen bonds with oxygen on the carbon surface, higher surface acidity lowers adsorption capacity due to increased polarity. In contrast, for adsorbates that can form hydrogen bonds with surface oxygen, the capacity is enhanced at higher surface acidities. A higher solvent hydrophobicity was found to decrease capacity for all the aromatic adsorbates studied, except at high surface polarity, where the effect of the solvent was found to be minimal.