Highly selective separation and detection of cyromazine from seawater using graphene oxide based molecularly imprinted solid‐phase extraction

A novel molecularly imprinted polymer based on graphene oxide was prepared as a solid‐phase extraction adsorbent for the selective adsorption and extraction of cyromazine from seawater samples. The obtained graphene oxide molecularly imprinted polymer and non‐imprinted polymer were nanoparticles and characterized by scanning electron microscopy. The imprinted polymer showed higher adsorption capacity and better selectivity than non‐imprinted polymer, and the maximum adsorption capacity was 14.5 mg/g. The optimal washing and elution solvents for molecularly imprinted solid phase extraction procedure were 2 mL of acetonitrile/water (80:20, v/v) and methanol/acetic acid (70:30, v/v), respectively. The recoveries of cyromazine in the spiked seawater samples were in the range of 90.3–104.1%, and the relative standard deviation was <5% (n = 3) under the optimal procedure and detection conditions. The limit of detection of the proposed method was 0.7 μg/L, and the limit of quantitation was 2.3 μg/L. Moreover, the imprinted polymer could keep high adsorption capacity for cyromazine after being reused six times at least. Finally, the synthesized graphene oxide molecularly imprinted polymer was successfully used as a satisfied sorbent for high selectivity separation and detection of cyromazine from seawater coupled with high‐performance liquid chromatography.     

An efficient strategy based on liquid‐liquid extraction and pH‐zone‐refining counter‐current chromatography for selective enrichment,separation, and purification of alkaloids and organic Acids from natural products

This study presents an efficient strategy based on liquid‐liquid extraction and pH‐zone‐refining counter‐current chromatography for selective enrichment, separation, and purification of alkaloids and organic acids from natural products. First, an acid or base modified two‐phase solvent system with maximum or minimum partition coefficient was developed for the liquid‐liquid extraction of the crude extract. As a result, alkaloids or organic acids could be selectively enriched in the upper or lower phase. Then pH‐zone‐refining counter‐current chromatography was employed to separate and purify the selectively enriched alkaloids or organic acids efficiently. The selective enrichment and separation of five bufadienolide from toad venom of Bufo marinus was used as an example to show the advantage of this strategy. As a result, 759 mg of selectively enriched bufadienolide was obtained from 2 g of crude extract and the total content of five targets was increased from 14.64 to 83%. A total of 31 mg of marinobufagin‐3‐adipoyl‐l ‐arginine, 42 mg of telocinobufagin‐3‐pimeloyl‐l ‐arginine, 51 mg of telocinobufagin‐3‐suberoyl‐l ‐arginine, 132 mg of marinobufagin‐3‐suberoyl‐l ‐arginine, and 57 mg of bufalin‐3‐suberoyl‐l ‐arginine were all simultaneously separated from 500 mg of selectively enriched sample, with the purity of 92.4, 97.5, 90.3, 92.1, and 92.8%, respectively.     

Facile synthesis of magnetic zinc metal‐organic framework for extraction of nitrogen‐containing heterocyclic fungicides from lettuce vegetable samples

We present a simple method for the fabrication of a magnetic amino‐functionalized zinc metal‐organic framework based on a magnetic graphene oxide composite. The resultant framework exhibited a porous 3D structure, high surface area and good adsorption properties for nitrogen‐containing heterocyclic fungicides. The adsorption process and capacity indicated that the primary adsorption mechanism might be hydrogen bonding and π‐π conjugation. In addition, an optimized protocol for magnetic solid phase extraction was developed (such as adsorbent content, pH, and desorption solvent), and utilized for the extraction of nitrogen‐containing heterocyclic fungicides from vegetable samples. Quantitation by high performance liquid chromatography coupled with tandem mass spectrometry offered a detection limit of 0.21–1.0 μg/L (S/N = 3) with correlation coefficients larger than 0.9975. These results demonstrate that magnetic amino‐functionalized zinc metal‐organic framewor is a promising adsorbent for the extraction and quantitation of nitrogen‐containing heterocyclic fungicides.     

Reversed‐phase liquid chromatography method for the determination of total plasma thiols after derivatization with 1‐benzyl‐2‐chloropyridinium bromide

A high‐performance liquid chromatography method was developed for simultaneous detection and quantitation of total cysteine, glutathione, homocysteine and cysteinylglycine in human plasma. The two key steps in the analysis are reduction of disulfides and treatment with 1‐benzyl‐2‐chloropyridinium bromide, which rapidly and quantitatively reacts with thiol groups to form stable S‐pyridinium derivatives with intense UV absorption. The derivatives are well separated on a Zorbax SB C₁₈ column using reversed‐phase high‐performance liquid chromatography and monitored at 315 nm. The calibration graphs were linear over concentration ranges covering most experimental and clinical cases with a regression coefficients better than 0.999. The detection and quantitation limits for all analytes were 0.2 and 0.5 µmol/L, respectively. The recoveries were 99.25–101.68%. The intra‐ and interassay imprecisions were 0.88–4.24 and 1.68–5.14%, respectively. The method was applied for plasma samples donated by apparently healthy volunteers. Copyright © 2009 John Wiley & Sons, Ltd.     

Syringe‐to‐syringe dispersive liquid‐phase microextraction solidified floating organic drop combined with high‐performance liquid chromatography for the separation and quantification of ochratoxin A in food samples

A new, simple, and rapid syringe‐to‐syringe dispersive liquid‐phase microextraction with solidified floating organic drop was used for the separation and preconcentration of ochratoxin A from grain and juice samples before its quantification using high‐performance liquid chromatography and fluorescence detection. Factors influencing the microextraction efficiency of ochratoxin A, such as sample solution pH, type and volume of organic extractant, salt concentration, number of injections, and volume of the sample, were studied and optimized. Under the optimum properties, the calibration graph showed linearity in the range of 65.0–700.0 ng/L (coefficient of determination = 0.9991). The limit of detection was 20.0 ng/L. The inter‐day and intra‐day relative standard deviations were in the range of 5.0–8.5%. This method was successfully applied for the quantification of ochratoxin A in grain and juice samples.     

Combination of ultrasound‐assisted ethyl chloroformate derivatization and switchable solvent liquid‐phase microextraction for the sensitive determination of l‐methionine in human plasma by GC–MS

A green and fast analytical method for the determination of l ‐methionine in human plasma is presented in this study. Preconcentration of the analyte was carried out by switchable solvent liquid phase microextraction after ethyl chloroformate derivatization reaction. Instrumental detection of the analyte was performed by means of gas chromatography–mass spectrometry. N,N‐Dimethyl benzylamine was used in the synthesis of switchable solvent. Protonated N,N‐dimethyl benzylamine volume, volume/concentration of sodium hydroxide, and vortex period were meticulously fixed to their optimum values. Besides, ethyl chloroformate, pyridine, and ethanol volumes were optimized in order to get high derivatization yield. After the optimization studies, limit of detection and quantitation values were attained as 3.30 and 11.0 ng/g, respectively, by the developed switchable solvent liquid phase microextraction gas chromatography–mass spectrometry method that corresponding to 76.7‐folds enhancement in detection power of the gas chromatography–mass spectrometry system. Applicability and accuracy of the switchable solvent liquid phase microextraction–gas chromatography–mass spectrometry method were also checked by spiking experiments. Percent recovery results were ranged from 97.8 to 100.5% showing that human plasma samples could be analyzed for its l ‐methionine level by the proposed method.     

Magnetic solid‐phase extraction or dispersive liquid–liquid microextraction for pyrethroid determination in environmental samples

The determination of 15 pyrethroids in soil and water samples was carried out by gas chromatography with mass spectrometry. Compounds were extracted from the soil samples (4 g) using solid–liquid extraction and then salting‐out assisted liquid–liquid extraction. The acetonitrile phase obtained (0.8 mL) was used as a dispersant solvent, to which 75 μL of chloroform was added as an extractant solvent, submitting the mixture to dispersive liquid–liquid microextraction. For the analysis of water samples (40 mL), magnetic solid‐phase extraction was performed using nanocomposites of magnetic nanoparticles and multiwalled carbon nanotubes as sorbent material (10 mg). The mixture was shaken for 45 min at room temperature before separation with a magnet and desorption with 3 mL of acetone using ultrasounds for 5 min. The solvent was evaporated and reconstituted with 100 μL acetonitrile before injection. Matrix‐matched calibration is recommended for quantification of soil samples, while water samples can be quantified by standards calibration. The limits of detection were in the range of 0.03–0.5 ng/g (soil) and 0.09–0.24 ng/mL (water), depending on the analyte. The analyzed environmental samples did not contain the studied pyrethroids, at least above the corresponding limits of detection.     

Separation and purification of two taxanes and one xylosyl‐containing taxane from Taxus wallichiana Zucc.: A comparison between high‐speed countercurrent chromatography and reversed‐phase flash chromatography

10‐Deacetylbaccatin III, an important semisynthetic precursor of paclitaxel and docetaxel, can be extracted from Taxus wallichiana Zucc. A process for the isolation and purification of 10‐deacetylbaccatin III ( 1 ), baccatin III ( 2 ), and 7β‐xylosyl‐10‐deacetyltaxol ( 3 ) from the leaves and branches of Taxus wallichiana Zucc. via macroporous resin column chromatography combined with high‐speed countercurrent chromatography or reversed‐phase flash chromatography was developed in this study. After fractionation by macroporous resin column chromatography, 80% methanol fraction was selected based on high‐performance liquid chromatography and liquid chromatography with mass spectrometry qualitative analysis. A solvent system composed of n‐hexane, ethyl acetate, methanol, and water (1.6:2.5:1.6:2.5, v/v/v/v) was used for the high‐speed countercurrent chromatography separation at a flow rate of 2.5 mL/min. The reversed‐phase flash chromatography separation was performed using methanol/water as the mobile phase at a flow rate of 3 mL/min. The high‐speed countercurrent chromatography separation produced compounds 1 (10.2 mg, 94.4%), 2 (2.1 mg, 98.0%), and 3 (4.6 mg, 98.8%) from 100 mg of sample within 110 min, while the reversed‐phase flash chromatography separation purified compounds 1 (9.8 mg, 95.6%) and 3 (4.9 mg, 97.9%) from 100 mg of sample within 120 min.     

Combination of ultracentrifugation and solid‐phase extraction with subsequent chromatographic analysis of α‐tocopherol in erythrocyte membranes

A novel and rapid sample pretreatment technique based on a combination of ultracentrifugation and solid‐phase extraction for the determination of α‐tocopherol in human erythrocyte membranes by high‐performance liquid chromatography with ultraviolet detection is presented in this work. Red blood cell samples were ultracentrifuged (288 000 × g, 3 min, 4°C) in the presence of d ‐mannitol, 4‐(2‐hydroxyethyl)‐1‐piperazineethanesulfonic acid and calcium chloride. The α‐tocopherol was then extracted from the erythrocyte membranes by solid‐phase extraction with n‐hexane in the presence of ascorbic acid. Tocopherol acetate was used as the internal standard. The extract was dissolved in methanol and separated on the monolithic column Chromolith Performance RP‐18e (100 × 4.6 mm) using 100% methanol as the mobile phase. The absorbance of α‐tocopherol was measured at a wavelength of 295 nm. The method was validated and showed sufficient accuracy and precision, ranging from 96.4 to 100.8% and from 4.5 to 6.3%, respectively. Moreover, the developed method was applied to the determination of erythrocyte α‐tocopherol in real samples from patients. The combined ultracentrifugation and solid‐phase extraction technique substantially decreased the time for the sample pretreatment step compared to liquid–liquid extraction and could be applicable for the quantitation of other analytes in erythrocyte membranes.     

Ionic liquids as mobile phase additives for determination of thiocyanate and iodide by liquid chromatography

An analytical method was developed for the simultaneous determination of thiocyanate and iodide by reversed‐phase liquid chromatography with UV detection using imidazolium ionic liquids as mobile phase additives. The chromatographic behaviors of the two anions on a C₁₈ column were studied and compared with four types of reagents including imidazolium ionic liquids, pyridinium ionic liquids, 4‐aminophenol hydrochloride and tetrabutylammonium as mobile phase additives. The effects of the concentrations of imidazolium ionic liquids, organic solvents and detection wavelength on separation and detection of the anions were investigated. The role of ionic liquids, retention rules and mechanisms were discussed. The separation of the anions was performed on the C₁₈ reserved‐phase column using acetonitrile‐0.3 mmol/L 1‐amyl‐3‐methylimidazolium tetrafluoroborate (10:90, v/v) as mobile phase, with column temperature of 35°C, flow rate of 1 mL/min and detection wavelength of 210 nm. Under these conditions, the two anions can be completely separated within 6 min. The limits of detection were 0.05 mg/L. The method was applied for the determination of thiocyanate and iodide in ionic liquid samples and iodide drugs, and the spiked recoveries ranged from 97 to 101%. The method is simple, accurate and meets the requirements of quantitative analysis for thiocyanate and iodide.     

An improved HPLC method for the investigation of L‐selenomethionine metabolism in rat gut contents

Selenomethionine (SeMet) is a widely used nutritional supplement that has potential benefit for people living in selenium‐deficient areas. Previous research has shown that selenium administered as SeMet undergoes significant enterohepatic recycling which may involve the gut microflora. In order to investigate this we have developed a simple method for the quantitation of l ‐SeMet in rat gut content suspensions prepared from jejunum, ileum, caecum and colon. After incubation of l ‐SeMet with gut content suspensions, samples were deproteinized with sulfosalicylic acid and derivatized with o‐phthaldialdehyde (OPA) and N‐acetyl‐l ‐cysteine (NAC). Mass spectrometry confirmed the formation of a 1:1:1 derivative of l ‐SeMet with OPA and NAC. Samples were analysed by reversed‐phase high‐performance liquid chromatography with fluorescence detection. The assay was linear in the concentration range 0.5–100 µg/mL (r² = 0.9992) with a limit of detection of 0.025 µg/mL (signal‐to‐noise ratio of 5). Intra‐day and inter‐day accuracies were 91.1–92.8 and 91.7–95.5%, respectively with corresponding precisions as relative standard deviation of <5%. Incubation of l ‐SeMet with gut content suspensions from different parts of the rat intestine showed that l ‐SeMet metabolism occurs mainly in the caecum. Copyright © 2009 John Wiley & Sons, Ltd.     

Simultaneous separation and determination of thallium in water samples by high‐performance liquid chromatography with inductively coupled plasma mass spectrometry

An analytical method for separation and determination of thallium species in water using high‐performance liquid chromatography with inductively coupled plasma mass spectrometry was developed. The composition and concentration of mobile phase, injection volume, and pH value were optimized respectively with an anion or cation exchange column. The results showed that Tl(I) and Tl(III) were effectively separated using anion exchange column Hamilton PRP‐X100, with the mobile phase consisting of 200 mmol/L ammonium acetate and 10 mmol/L diethylenetriaminepentaacetic acid (pH = 4.2). When using a Dionex cation exchange guard column, CS12A, 15 mmol/L HNO₃, and 3 mmol/L diethylenetriaminepentaacetic acid as the mobile phase, Tl(I) and Tl(III) could be effectively separated. The detection limits of the methods were 3–6 and 9–12 ng/L, respectively. In a solution containing Fe ions and oxalic acid, a significant quantity of Tl(I) was oxidized. Fe ions and oxalic acid in the water samples did not interfere with high‐performance liquid chromatography‐inductively coupled plasma mass spectrometry measurement results.     

Switchable‐hydrophilicity solvent liquid‐liquid microextraction versus dispersive liquid‐liquid microextraction prior to HPLC‐UV for the determination and isolation of piperine from Piper nigrum L

Switchable‐hydrophilicity solvent liquid‐liquid microextraction and dispersive liquid‐liquid microextraction were compared for the extraction of piperine from Piper nigrum L. prior to its analysis by using high‐performance liquid chromatography with UV detection. Under optimum conditions, limits of detection and quantitation were found as 0.2–0.6 and 0.7–2.0 μg/mg with the two methods, respectively. Calibration graphs showed good linearity with coefficients of determination (R²) higher than 0.9962 and percentage relative standard deviations lower than 6.8%. Both methods were efficiently used for the extraction of piperine from black and white pepper samples from different origins and percentage relative recoveries ranged between 90.0 and 106.0%. The results showed that switchable‐hydrophilicity solvent liquid‐liquid microextraction is a better alternative to dispersive liquid‐liquid microextraction for the routine analysis of piperine in food samples. A novel scaled‐up dispersive liquid‐liquid microextraction method was also proposed for the isolation of piperine providing a yield of 102.9 ± 4.9% and purity higher than 98.0% as revealed by NMR spectroscopy.     

Simultaneous quantification and rat pharmacokinetics of formononetin‐7‐O‐β‐d‐glucoside and its metabolite formononetin by high‐performance liquid chromatography–tandem mass spectrometry

Formononetin‐7‐O‐β‐d ‐glucoside has been proved to have significant anti‐inflammatory effect. To evaluate its rat pharmacokinetics, a rapid, sensitive, and specific liquid chromatography–tandem mass spectrometry method has been developed and validated for the quantification of formononetin‐7‐O‐β‐d ‐glucoside and its main metabolite formononetin in rat plasma. Samples were pretreated using a simple protein precipitation and the chromatographic separation was performed on a C₁₈ column by a gradient elution using a mobile phase consisting of water and acetonitrile both containing 0.1% formic acid. Both analytes were detected using a tandem mass spectrometer in positive multiple reaction monitoring mode. The assay showed wide linear dynamic ranges of both 0.10–100 ng/mL, with acceptable intra‐ and inter‐batch accuracy and precision. The lower limits of quantification were both 0.10 ng/mL using 50 μL of rat plasma for two analytes. The method has been successfully used to investigate the oral pharmacokinetic profiles of both analytes in rats. After oral administration of formononetin‐7‐O‐β‐d ‐glucoside at the dose of 50 mg/kg, it was rapidly absorbed in vivo and metabolized to its metabolite formononetin. The plasma concentration‐time profiles both showed double‐peak phenomena, which would be attributed to the strong enterohepatic circulation of formononetin‐7‐O‐β‐d ‐glucoside.     

Primary secondary amine as a sorbent material in dispersive solid‐phase extraction clean‐up for the determination of indicator polychlorinated biphenyls in environmental water samples by gas chromatography with electron capture detection

A simple, rapid, and novel method has been developed and validated for determination of seven indicator polychlorinated biphenyls in water samples by gas chromatography with electron capture detection. 1 L of water samples containing 30 g of anhydrous sodium sulfate was first liquid–liquid extracted with an automated Jipad‐6XB vertical oscillator using n‐hexane/dichloromethane (1:1, v/v). The concentrated extract was cleaned up by dispersive solid‐phase extraction with 100 mg of primary secondary amine as sorbent material. The linearity of this method ranged from 1.25 to 100 μg/L, with regression coefficients ranging between 0.9994 and 0.9999. The limits of detection were in the ng/L level, ranging between 0.2 and 0.3 ng/L. The recoveries of seven spiked polychlorinated biphenyls with external calibration method at different concentration levels in tap water, lake water, and sea water were in the ranges of 85–112, 76–116, and 72–108%, respectively, and with relative standard deviations of 3.3–4.5, 3.4–5.6, and 3.1–4.8% (n =  5), respectively. The performance of the proposed method was compared with traditional liquid–liquid extraction and solid‐phase extraction clean‐up methods, and comparable efficiencies were obtained. It is concluded that this method can be successfully applied for the determination of polychlorinated biphenyls in different water samples.     

Quantitative analysis of ripasudil hydrochloride hydrate and its impurities by reversed‐phase high‐performance liquid chromatography after precolumn derivatization: Identification of four impurities

We report the development and validation of a stability‐indicating reversed‐phase high‐performance liquid chromatography method with precolumn derivatization for the separation and identification of the impurities of ripasudil hydrochloride hydrate, a novel protein kinase inhibitor. 2,3,4,6‐Tetra‐O‐acetyl‐β‐d ‐glucopyranosyl isothiocyanate was chosen as the derivatizing reagent and triethylamine was added as catalyst. 200 μL sample solution (1 mg/mL), 600 μL derivatizing reagent (1 mg/mL), and 200 μL triethylamine solution (1%, v/v) were mixed and reacted at 40°C for 30 min. The separation was achieved on an Inertsil C₁₈ ODS‐3 (250 mm × 4.6 mm, 5 μm) column using mobile phases including 10 mmol monopotassium phosphate buffer (pH 3.0) and methanol in gradient mode. The column temperature was adjusted at 25°C and the flow rate at 1 mL/min. The detection was carried out at 220 nm. Different precolumn derivatization conditions as well as the high‐performance liquid chromatography conditions were optimized. Ripasudil hydrochloride hydrate and its four impurities were detected and quantitated, among which two new compounds were characterized. The proposed method was validated and proven to be selective, accurate, and precise and suitable for the quantitative analysis of ripasudil hydrochloride hydrate.     

Determination of methyl methanesulfonate and ethyl methanesulfonate in methanesulfonic acid by derivatization followed by high‐performance liquid chromatography with ultraviolet detection

Methanesulfonic acid is routinely used in pharmaceuticals but can contain potentially genotoxic impurities such as methyl methanesulfonate and ethyl methanesulfonate. The aim of this study was to develop a simple high‐performance liquid chromatography with ultraviolet detection method for determining methyl methanesulfonate and ethyl methanesulfonate in methanesulfonic acid. Samples (250 mg) in water/acetonitrile (200 μL) were first combined with 10.0 mol/L sodium hydroxide solution (270 μL). Then they were mixed with 2.0 mg/mL N ,N‐diethyldithiocarbamate (500 μL), diluted to 5 mL with N ,N‐dimethylacetamide and allowed to react at 80°C for 1 h. The derivatives were analyzed using gradient high‐performance liquid chromatography with ultraviolet detection (277 nm) and structurally elucidated by liquid chromatography with mass spectrometry. With acetonitrile/5 mmol/L ammonium acetate solution as the eluent and 1 mL/min as the flow rate on a C18 column, the derivatives were eluted at 10.6 and 14.8 min. Good linearity (correlation coefficients > 0.999) and low limits of quantitation (0.6 ppm) were obtained. The recoveries were in the range of 80–115% with relative standard deviation < 5.0%. Finally, the established method was successfully used for the determination of methyl methanesulfonate and ethyl methanesulfonate in methanesulfonic acid.     

Determination of major phenolic compounds in apples: Part I—Optimization of high‐performance liquid chromatography separation with diode array detection

The separation of seven phenolic compounds including gallic acid, chlorogenic acid, epicatechin, quercitrin, rutin, phloridzin, and phloretin present in apple peel and pulp and differing in elution properties has been optimized using high‐performance liquid chromatography with diode array detection. Several stationary phases were tested to achieve the efficient separation of phenolic compounds in fruit extracts and C18 was found to be the most efficient. Core–shell and fully porous C18 packings were assessed with respect to the complex composition of the fruit extracts. The developed high‐performance liquid chromatography method comprised gradient elution in which mobile phase A was water at pH 2.8 adjusted with acetic acid and B was acetonitrile. The gradient shape was the following: 0 min 95% A/5% B, 2.5 min 85% A/15% B, 12 min 50% A/50% B, 15 min 95% A/5% B. The flow rate was 1 mL/min, injection volume 10 μL, and UV detection at 255, 280, 320, and 365 nm was applied. Our method was validated for both C18 core–shell and fully porous packings. The resolution 6.2–14.8, symmetry 0.99–1.34, peak capacity 18–60, peak area repeatability 0.45–1.00% relative standard deviation, calibration range 0.125–5 mg/mL (0.25–10 mg/mL for chlorogenic acid and rutin), correlation coefficients of calibration curve 0.9976–0.9997, and accuracy evaluated as recovery 95.56–107.54% were determined for the core–shell column.     

Pressurized liquid extraction of cyclitols and sugars: optimization of extraction parameters and selective separation

Cyclitols and sugars were obtained as a mixture from Medicago sativa L., in a comparative study by using maceration, and pressurized liquid extraction, as a modern and green extraction techniques. The influence of extraction parameters including: extraction temperature, time and number of cycles on the content of sugars and cyclitols was investigated based on response surface methodology. The highest total amount of sugars and cyclitols (62.27 ± 2.30 and 50.35 ± 0.77 mg/g of dry material, respectively) was obtained when extraction was performed at 88°C, for 22 min, in two cycles. The methodology used involved extraction, purification, selective separation (using yeast and anion exchange resin) and derivatization, followed by gas chromatography ‐mass spectrometry analysis. The use of yeast treatment realized an effective fractionation of cyclitols and sugars, which allowed the removal of most sugars. The involvement of anion exchange resin after yeast allowed the removal of sugar alcohols and lactose, together with other sugar traces remained and to obtain a solution containing six cyclitols. The recrystallization of dry residue after solvent evaporation, from ethanol, allowed us to obtain 14.65 mg of white pure crystals identified with NMR spectroscopy, liquid chromatography with mass spectrometry, gas chromatography with mass spectrometry, optical rotation and melting point as analysis D‐pinitol.     

Preparative enantioseparation of loxoprofen precursor by recycling countercurrent chromatography with hydroxypropyl‐β‐cyclodextrin as a chiral selector

Recycling countercurrent chromatography was successfully applied to the resolution of 2‐(4‐bromomethylphenyl)propionic acid, a key synthetic intermediate for synthesis of nonsteroidal anti‐inflammatory drug loxoprofen, using hydroxypropyl‐β‐cyclodextrin as chiral selector. The two‐phase solvent system composed of n‐hexane/n‐butyl acetate/0.1 mol/L citrate buffer solution with pH 2.4 (8:2:10, v/v/v) was selected. Influence factors for the enantioseparation were optimized, including type of substituted β‐cyclodextrin, concentration of hydroxypropyl‐β‐cyclodextrin, separation temperature, and pH of aqueous phase. Under optimized separation conditions, 50 mg of 2‐(4‐bromomethylphenyl)propionic acid was enantioseparated using preparative recycling countercurrent chromatography. Technical details for recycling elution mode were discussed. The purities of both the S and R enantiomers were over 99.0% as determined by high‐performance liquid chromatography. The enantiomeric excess of the S and R enantiomers reached 98.0%. The recovery of the enantiomers from eluted fractions was 40.8–65.6%, yielding 16.4 mg of the S enantiomer and 10.2 mg of the R enantiomer. At the same time, we attempted to enantioseparate the anti‐inflammatory drug loxoprofen by countercurrent chromatography and high‐performance liquid chromatography using a chiral mobile phase additive. However, no successful enantioseparation was achieved so far.