A promising dehydrogenase-based bioanode for a glucose biosensor and glucose/O2 biofuel cell

A new type of dehydrogenase-based amperometric glucose biosensor was constructed using glucose dehydrogenase (GDH) which was immobilized on the edge-plane pyrolytic graphite (EPPG) electrode modified with poly(phenosafranin)-functionalized single-walled carbon nanotubes (PPS-SWCNTs). The PPS-SWCNT-modified EPPG electrode was prepared by electropolymerization of phenosafranin on the EPPG electrode which had been previously coated with SWCNTs. The performance of the GDH/PPS-SWCNT/EPPG bioanode was evaluated using cyclic voltammetry and amperometry in the presence of glucose. The GDH/PPS-SWCNT/EPPG electrode possesses promising characteristics as a glucose sensor: a wide linear dynamic range of 50 to 700 μM, low detection limit of 0.3 μM, fast response time (1-2 s), high sensitivity (96.5 μA cm(-2) mM(-1)), and anti-interference and anti-fouling abilities. Moreover, the performance of the GDH/PPS-SWCNT/EPPG bioanode was tested in a glucose/O(2) biofuel cell. The maximum power density delivered by the assembled glucose/O(2) biofuel cell could reach 64.0 μW cm(-2) at a cell voltage of 0.3 V with 40 mM glucose.     

Determination of hydroxylamine using a carbon paste electrode modified with graphene oxide nano sheets

A carbon paste electrode that was chemically modified with 3-(4'-amino-3'-hydroxy-biphenyl-4-yl)-acrylic acid (3,4-AA) was used as a selective electrochemical sensor for the detection of hydroxylamine. Cyclic voltammetry (CV), choronoamperometry (CHA) and square wave voltammetry (SWV) were used to investigate oxidation of hydroxylamine in aqueous solution. Under optimized concentration the electrocatalytic oxidation current peak for hydroxylamine increased linearly with concentration in the range of 0.025–10.0 μM. The detection limits for hydroxylamine was 0.012 μM. Finally, the modified electrode was applied to detection hydroxylamine in water samples.     

Nafion-graphene composite film modified glassy carbon electrode for voltammetric determination of p-aminophenol

A Nafion-graphene (Nafion-GR) nanocomposite film modified glassy carbon electrode was fabricated by a simple drop-casting method, and used in the electrochemical detection of p-aminophenol (4-AP). Owing to the large surface area, good conductivity of GR and good affinity of Nafion, the sensor exhibited excellent electrocatalytic activity for the oxidation of 4-AP. The electrochemical behaviors of 4-AP on Nafion/GR film modified glassy carbon electrodes were investigated by cyclic voltammetry and differential pulse voltammetry. A calibration curve is constructed in the same matrix, urine, as the unknown samples to be analyzed. The Nafion-GR film modified electrode was linearly dependent on the 4-AP concentration and the linear analytical curve was obtained in the ranges of 0.5–200 μM with differential pulse voltammetry (DPV) and the detection limit was 0.051 μM. The Nafion-graphene nanocomposite modified electrode exhibited good reusability than pure graphene modified GCE. This procedure can be used for the determination of p-aminophenol in the presence of its degradation products and paracetamol. Finally, the proposed method was successfully used to determine p-aminophenol in local tap water samples in urine samples and pharmaceutical preparations.     

Electrochemical modification of a carbon paste electrode with poly (1,5-diaminonaphthalene) and copper-cobalt nanostructures for the determination of thioctic acid in real samples

This study used square-wave voltammetry and cyclic voltammetry to investigate the electrochemical oxidation of Thioctic Acid (TA) on a Carbon Paste Electrode (CPE) modified with copper-cobalt nanostructures and poly (1,5-Diaminonaphthalene). The voltammetric sensor was sensitive to the oxidation of TA. In addition, we optimized the effects of multiple cycles of deposition of Cu-Co nanostructures, and electro-polymerization of monomer 1,5-DAN, scan rate, and pH. The sensor showed good identification capabilities for TA. The linear responses obtained ranged from 0.6 μM to 150 μM with a detection limit of 0.48 μM for the modified CPE. The adsorption process controlled the oxidation of TA. We used the proposed sensor and method to determine TA in real samples.     

Application of nanosized MCM-41 to fabrication of a nanostructured electrochemical sensor for the simultaneous determination of levodopa and carbidopa

A novel carbon paste electrode modified with nanosized mesoporous MCM-41 was prepared, and used as an electrochemical sensor to study the electro oxidation of levodopa (LD), carbidopa (CD) and their mixtures. Using differential pulse voltammetry (DPV), a highly selective and simultaneous determination of LD and CD has been explored at the modified electrode. The electrochemical sensor displayed a good resolving function for the overlapping voltammetric responses of LD and CD into two separate peaks with a potential difference of 370 mV. DPV peak currents of LD increased linearly with concentration over the 0.13 μM to 1250.00 μM range and exhibited a detection limit of 0.072 μM. Also, the proposed electrochemical sensor was used for the determination of LD and CD in some real samples, using the standard addition method.     

A Novel Hybrid Nano‐composite Grafted Electrochemically Reduced Graphene Oxide Based Sensor for Sensitive Determination of Efavirenz

A novel, facile fabrication, based on electrochemically reduced graphene oxide (ErGO), grafted with Pt nanoparticles and Nafion hybrid nano‐composite (ErGO‐Pt/Nafion) on the surface of edge plane pyrolytic graphite (EPPG) has been reported. The fabricated sensor has been used for the sensitive and selective determination of efavirenz (EFZ), a well‐known drug for HIV infections. The ErGO‐Pt/Nafion film was characterized by Field Emission Scanning Electron Microscopy (FE‐SEM), Energy‐dispersive X‐ray spectrometry (EDS) and Electrochemical Impedance Spectroscopy (EIS). The experimental results reveal that the modified sensor displays an excellent electrocatalytic activity towards the oxidation of EFZ and exhibits a large linear dynamic relationship in the range of 0.05 μM to 150 μM, with a detection limit of 1.8 nM. Practical utility of the developed sensor has been demonstrated by determining the EFZ in biological fluids and pharmaceutical samples and a low detection limit with high sensitivity observed makes it valuable for the clinical diagnosis.     

Enhanced Performance of Edge‐Plane Pyrolytic Graphite (EPPG) Electrodes over Glassy Carbon (GC) Electrodes in the Presence of Surfactants: Application to the Stripping Voltammetry of Copper

The voltammetric performance of glassy carbon (GC) and edge‐plane pyrolytic graphite (EPPG) electrodes was investigated for the oxidation of potassium ferrocyanide in aqueous solution both with and without the addition of surfactant (sodium dodecyl sulfate and Triton X‐100). The heterogeneous electron transfer kinetics were determined for all cases, and it was found that the GC electrode surface was far more sensitive to the presence of surfactant than the more hydrophilic EPPG surface. This result was then applied to the electroanalysis of copper via adsorptive stripping voltammetry in the presence of Triton X‐100 and it was observed that the EPPG electrode response was unaffected by up to 100 μM of surfactant, whilst the voltammetry on the GC electrode was significantly affected by only 10 μM.     

Voltammetric Determination of Neotame by Using Chitosan/Nickelnanoparticles/Multi Walled Carbon Nanotubes Biocomposite as a Modifier

A selective and simple biosensor was prepared by immobilizing chitosan/nickelnanoparticles/multi-walled carbon nanotubes biocomposite on the glassy carbon electrode surface for voltammetric quantification of neotame. The properties and morphology of the modified electrode surfaces were characterized by scanning electron microscope (SEM), energy dispersive X-ray analysis (EDX). Electro oxidation of neotame on this modified surface was examined through cyclic voltammetry (CV) and square wave voltammetry (SWV) techniques. The biocomposite modified surface (Chi/NiNPs/MWCNTs/GCE) proposed in this study showed good electrocatalytic activity for neotame with an improved voltammetric peak current at 1.004 V, unlike the bare glassy carbon electrode (GCE) surface and several other modified surfaces. Under optimum conditions, Chi/NiNPs/MWCNTs/GCE gave linear SWV responses at the range of 2 μM ∼50 μM for neotame with 0.84 μM determination limit. This voltammetric sensor was successfully employed for the quantification of neotame on food samples and showed long-term stability, advanced voltammetric behavior, and good repeatability. Selective, accurate, and precise determination of neotame highlight the importance of this electrode in monitoring the control of food additives and ensures attract a great deal of attention.     

Nickel and Tungsten Bimetallic Nanoparticles Modified Pencil Graphite Electrode: A High-performance Electrochemical Sensor for Detection of Endocrine Disruptor Bisphenol A

In this work, an economically viable, very low cost, indigenous, ubiquitously available electrochemical sensor based on bimetallic nickel and tungsten nanoparticles modified pencil graphite electrode (NiNP-WNP@PGE) was fabricated for the sensitive and selective detection of bisphenol A (BPA). The NiNP-WNP@PGE sensor was prepared by a facile electrochemical one step co-deposition method. The prepared nanocomposite was morphologically characterized by scanning electron microscopy (SEM), energy dispersive X-ray (EDX), X-ray diffraction (XRD), electrochemically by cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). The proposed sensor displayed high electrocatalytic activity towards electro-oxidation of BPA with one irreversible peak. The fabricated sensor displayed a wide detection window between 0.025 μM and 250 μM with a limit of detection of 0.012 μM. PGE sensor was successfully engaged for the detection of BPA in bottled water, biological, and baby glass samples.     

A Sensitive Electrochemical Sensor for Voltammetric Determination of Ganciclovir Based on Au‐ZnS Nanocomposite

An electrode modified with ZnS and gold nanoparticles (Au‐ZnS NPs) is introduced for highly sensitive voltammetric determination of ganciclovir (GCV). Surface structure and topography of the modified electrode was studied by SEM, EDX and XRD techniques. Electrochemical oxidation of GCV was investigated by cyclic (CV) and square wave voltammetry (SWV) in Briton‐Robinson buffer solution (pH 1.5). The results showed that electrochemical oxidation of GCV at the Au‐ZnS modified glassy carbon electrode (GCE) is irreversible and exhibited diffusion controlled electrode process over the pH range from 1.0 to 6.0. The oxidation potential peak and pH relationship showed that electrons and protons were transferred simultaneously over the electrochemical oxidation process. Using the proposed sensor, the linear calibration curves were obtained in the ranges of 0.04–1.50 μM and 1.5–70.0 μM with detection limit of 0.01 μM GCV by SWV technique. The modified electrode was successfully applied as a sensitive, reproducible and repeatable sensor for determination of the trace amount of GCV in human serum, urine and cymevene vials. Reasonable results were obtained from comparing the measurements of the real samples by the new sensor to high performance liquid chromatography (HPLC) as a standard method.     

Room-Temperature Ionic Liquid and Multi-Walled Carbon Nanotube Composite Modified Carbon-Ceramic Electrode as a Sensitive Voltammetric Sensor for Indomethacin

The electrochemical behavior of indomethacin on the surface of a carbon-ceramic electrode modified with multi-walled carbon nanotubes and an ionic liquid composite film is reported. The results show that the nano-structured film exhibited excellent enhancement effects on the electrochemical oxidation of indomethacin. The developed sensor presented a linear response to indomethacin over the concentration range from 1 to 50 µM with a detection limit of 0.26 µM. The proposed modified electrode was employed for the determination of indomethacin in biological and pharmaceutical samples using differential pulse voltammetry.     

A non‐covalent functionalization of copper tetraphenylporphyrin/chemically reduced graphene oxide nanocomposite for the selective determination of dopamine

A non‐covalent functionalization based on a copper tetraphenylporphyrin/chemically reduced graphene oxide (Cu‐TPP/CRGO) nanocomposite is demonstrated for selective determination of dopamine (DA) in pharmaceutical and biological samples. A homogeneous electron‐rich environment can be created on the graphene surface by Cu‐TPP due to the π–π non‐covalent stacking interaction. The synthesized Cu‐TPP/CRGO nanocomposite was characterized using scanning electron microscopy NMR, ultraviolet–visible and electrochemical impedance spectroscopies. The electrocatalytic activity of DA was evaluated using cyclic voltammetry and differential pulse voltammetry. The oxidation peak current (I_pa) of DA increased linearly with increasing concentration of DA in the range 2–200 μM. The detection limit was calculated as 0.76 μM with a high sensitivity of 2.46 μA μM^?1 cm ^{? 2}. The practicality of the proposed DA sensor was evaluated in DA hydrochloride injection, human urine and saliva, and showed satisfactory recovery results for the detection of DA. In addition, the Cu‐TPP/CRGO nanocomposite‐modified electrode showed excellent stability, repeatability and reproducibility towards the detection of DA. Copyright © 2015 John Wiley & Sons, Ltd.     

Electrocatalytic oxidation of hydrazine at poly(4,5-dihydroxy-1,3-benzenedisulfonic acid) multiwall carbon nanotubes modified-glassy carbon electrode: Improvement of the catalytic activity

A stable electroactive thin film of poly(4,5-dihydroxy-1,3-benzenedisulfonic acid) was electrochemically deposited at the surface of multiwall carbon nanotubes-glassy carbon electrode. The electrocatalytic oxidation of hydrazine has been studied at the surface of the modified electrode using cyclic voltammetry, chronoamperometry and linear sweep voltammetry as diagnostic techniques. The modified electrode exhibits good electrocatalytic activity for the oxidation of hydrazine with a good sensitivity. Linear calibration range was in the wide concentration range of 10–3540 μM hydrazine with a detection limit of 1.8 μM and a sensitivity of 85.3 nA/μM. A Tafel plot, derived from voltammograms, indicated a one-electron transfer process to be the rate-limiting step and the overall number of electrons involved in the catalytic oxidation of hydrazine was found to be four. The influences of potentially interfering substances were studied. The diffusion coefficient of hydrazine was also evaluated. Finally, the proposed modified electrode was used for the determination of hydrazine in spiked water samples.     

Determination of Tyrosine in the Presence of Sodium Dodecyl Sulfate Using a Gold Nanoparticle Modified Carbon Paste Electrode

A carbon paste electrode modified with gold nanoparticles (AuMCPE) was used as a highly sensitive sensor for determination of Tyrosine (Tyr), in the presence of an anionic surfactant, sodium dodecyl sulfate (SDS), in aqueous solution. The measurements were carried out by using of differential pulse voltammetry (DPV), cyclic voltammetry (CV), amd chronocoulometry and chronoamperometry methods. The prepared electrode shows voltammetric responses with high sensitivity and selectivity for Tyr in the presence of SDS. The relationship between the oxidation peak current of Tyr and its concentration was obtained linearly and it was 1.0 × 10^?7 to 1.0 × 10^?5 M with a detection limit of 5.5 × 10^?8 M in the absence of SDS. On the other hand the oxidation peak current of Tyr increased significantly at AuMCPE in the presence of SDS and its detection limit was reduced to 2.7 × 10^?9 M. The proposed voltammetric approach was also applied to the determination of Tyr concentration in human serum.     

Non‐enzymatic Electrochemical Sensor for the Simultaneous Determination of Xanthine,its Methyl Derivatives Theophylline and Caffeine as well as its Metabolite Uric Acid

Xanthine and its methyl derivatives, theophylline and caffeine are purines which find important roles in biological systems. The simultaneous voltammetric behaviour of these purines has been studied on a glassy carbon electrode modified with an electropolymerised film of para amino benzene sulfonic acid. Well defined and well separated peaks were obtained for the oxidation of xanthine, theophylline and caffeine on the polymer modified electrode in the square wave mode. The experimental requirements to obtain the best results for individual as well as simultaneous determination were optimised. The signal for the electro‐oxidation was found to be free of interferences from each other in the range 0.9 – 100 μM in the case of xanthine and from 10–100 μM in the case of theophylline and caffeine with detection limits 0.35 μM, 7.02 μM and 11.95 μM respectively. The simultaneous determination of uric acid, the final metabolic product of xanthine oxidation in biological systems could also be accomplished along with xanthine, theophylline and caffeine atphysiological pH. The mechanistic aspects of the electro‐oxidation on the polymer modified electrode was also studied using linear sweep voltammetry. Chronoamperometry was employed to determine the diffusion coefficient of these xanthines. The developed sensor has been successfully demonstrated to be suitable for the determination of these compounds in real samples without much pre‐treatment.     

Selective and Sensitive Nitrite Sensor Based on Glassy Carbon Electrode Modified by Silver Nanochains

Herein, we report a facile method for the synthesis of silver nanochains (Ag nanochains) using pyridine as growth directing agent and citrate ions as capping agents in alkaline medium. The characterization of the synthesized high aspect ratio Ag nanochains was accomplished with the help of Transmission Electron Microscopy (TEM) and High Resolution Transmission Electron Microscopy (HRTEM) which demonstrates the thickness below 100 nm. Crystalline nature of the synthesized Ag nanochains was investigated using X‐ray diffractrometry. A sensitive electrochemical nitrite sensor was assembled using synthesized Ag nanochains as electrode modifier. An improved cyclic voltammetric response for the oxidation of nitrite ions was witnessed at the modified GCE surface in comparison to bare GCE in Britton Robinson (BR) buffer (pH 4). The influence of pH on the oxidation peak current of nitrite ions was also examined using cyclic voltammetry. The electrocatalytic oxidation currents attained through amperometric measurements at Ag nanochains modified GCE were linearly dependent on the concentration of nitrite ions in the two ranges of 0.5–7.5 µM, 5–480 µM. Linear calibration plots of Ip vs. concentration of nitrite were also constructed at the proposed sensor using square wave voltammetry and differential pulse voltammetry. The proposed sensing strategy was successfully employed for the determination of nitrite in water samples with excellent recoveries.     

Application of Carbon Paste Electrode Modified with Carbon Nanofibres/Polyaniline/Platinum Nanoparticles as an Electrochemical Sensor for the Determination of Bezafibrate

The present study deals with the development of an electrochemical sensor for quantitative determination of Bezafibrate (BZF) based on carbon nanofibers/polyaniline/platinum nanoparticles modified carbon paste electrode (CNF/PANI/Pt/CPE). BZF is a fibric acid derivative and is used largely in the treatment of lipid disorders. The nanocomposite was synthesized by in situ polymerization of aniline using ammonium persulphate and platinum nanoparticles were uniformly decorated on the CNF/PANI surface by reducing hexachloroplatinic acid using sodium borohydride. The electrochemical response of BZF at CNF/PANI/Pt/CPE was studied using cyclic voltammetry (CV), differential pulse voltammetry (DPV) and electrochemical impedance spectroscopy (EIS). The above study resulted into significant improvement of the electrochemical signal towards the oxidation of BZF, revealing that the oxidation process is highly favorable at the surface of modified electrode. The anodic peak current I_p (μA) is found to be linearly dependent on BZF concentration in the range of 0.025 μM to 100 μM with a detection limit of 2.46 nM. The practical analytical utilities of the sensor were investigated by performing the experiments on synthetic pharmaceutical formulations, human blood serum and urine samples which offered good recovery, suggesting the high efficacy and authenticity of CNF/PANI/Pt/CPE sensor for BZF determination.     

Highly Sensitive Nanostructured Electrochemical Sensor Based on Carbon Nanotubes-Pt Nanoparticles Paste Electrode for Simultaneous Determination of Levodopa and Tyramine

A multicomponent electrochemical sensor, with two nanometer-scale components in sensing matrix/electrode, was used to simultaneous determination of levodopa (LD) and tyramine (TR) in pharmaceutical and diet samples. Multiwall carbon nanotubes (MWCNTs) were used as carbonaceous materials in the electrode construction. 5-amino-3',4'-dimethoxy-biphenyl-2-ol (5ADMB) was used as electron mediator and Pt nanoparticles (nPt) as a catalyst. The 5ADMB catalyzes the oxidation of LD to the corresponding catecholamine, which is electrochemically reduced back to LD. Preparation of this electrode was very simple and modified electrode showed good properties at electrocatalytic oxidization of LD and TR. Using differential pulse voltammetry (DPV), a highly selective and simultaneous determination of LD and TR has been explored at the modified electrode. Differential pulse voltammetry peak currents of LD and TR increased linearly with their concentrations at the ranges of 0.50–100.0 μM and 0.60–100.0 μM, respectively. Also, the detection limits for LD and TR were 0.31 and 0.52 μM, respectively. The electrode exhibited an efficient catalytic response with good reproducibility and stability.     

Development of Pen-type Portable Electrochemical Sensor Based on Au-W Bimetallic Nanoparticles Decorated Graphene-chitosan Nanocomposite Film for the Detection of Nitrite in Water,Milk and Fruit Juices

The development and fabrication of a simple, portable, and sensitive detection tool to precisely monitor nitrite level is of growing importance in electrochemistry research, given the strong interest in the protection of drinking water quality, treatment of wastewater, food production, and control of remediation processes. This work describes the fabrication of a simple, cost-effective, pen-type electrochemical sensor based on bimetallic gold and tungsten nanoparticles electrochemically decorated on graphene-chitosan modified pencil graphite electrode (PGE) for the trace detection of nitrite in real samples. The prepared nanocomposite was characterized using XRD, SEM, and EDS. The electrochemical behavior of the sensor was evaluated by cyclic voltammetry (CV) and impedance electrochemical spectroscopy (EIS). Results revealed that the proposed sensor displayed excellent electrocatalytic activity towards electro-oxidation of nitrite with an irreversible redox reaction. The AuNPs-WNPs@Gr-Chi/PGE sensor exhibited excellent analytical performance with a wide linear range from 10 to 250 μM towards nitrite. The LOD and LOQ were calculated to be 0.12 μM and 0.44 μM, respectively. The designed electrochemical sensor was successfully applied for the detection of nitrite in water, milk, and natural fruit juice samples.     

Sensitive determination of diuron on zinc oxide nanoparticles modified carbon paste electrode in soil and water samples

An electrochemical sensor based on Zinc oxide nanoparticles (ZnONPs) modified carbon paste electrode was designed for the toxic diuron pesticide detection. The ZnONPs were synthesized through the hydrothermal route and their structural properties were investigated via scanning electron microscopy (SEM) and X-ray diffraction powder (XRD). The designed ZnONPs-modified carbon paste electrode (ZnONPs-CPE) was characterized using cyclic voltammetry and electrochemical impedance spectroscopy. The sensor showed significantly enhanced sensitivity on the diuron oxidation peak current, compared to the bare carbon paste electrode. Qualitative and quantitative analysis were performed using cyclic voltammetry (CV) and square wave voltammetry (SWV). Experimental parameters such as pH, amount of ZnONPs and frequency were evaluated and the optimized conditions were obtained with 0.1 M phosphate buffer solution at pH=8, a frequency of 50 Hz and a quantity of 5 mg of ZnONPs. Under these conditions, linear responses ranging from 1.3 to 7.7 μM and 8.6 to 30 μM of diuron were obtained, with correlation coefficients of R²=0.994 and 0.996 respectively. Detection and quantification limits of 0.22 μM and 0.84 μM (S/N=3) were respectively achieved based on the 3σ method. The interference of some ions on the oxidation peak of diuron on ZnONPs-CPE was also evaluated and no interference was observed, therefore demonstrating the selectivity of the sensor. The proposed sensor, designed with ecofriendly materials, is sensitive, selective and was effectively used for diuron determination in soils and water samples with recoveries ranging from 98 % to 101.5 %.