Novel Sn Doped Co3O4 Thin Film for Nonenzymatic Glucose Bio‐Sensor and Fuel Cell

A facile chemical solution deposition via two‐step spin coating technique was used to fabricate nano‐particulate novel Sn doped Co₃O₄ thin film for glucose sensor and fuel cell applications. Substitution of Sn into Co₃O₄ host lattice lead to a remarkable increase in the electrocatalytic activity of the Co₃O₄ electrode material. Film thickness played a significant role in enhancing the charge transferability of the electrode as was observed from electrochemical impedance spectroscopy (EIS). The best sensor exhibited two wide linear response ranges (2 μM up to ∼0.5 mM and 0.6 mM up to ∼5.5 mM respectively) with sensitivities of 921 and 265 μA cm⁻² mM⁻¹ respectively and low limit of detection of 100 nM (S/N=3). The sensor was very selective towards glucose in the presence of various interference and showed long term stability. Moreover, the developed thin film modified electrode could generate one electron current in nonenzymatic fuel cell setup at room temperature.     

Binderless Solution Processed Zn Doped Co3O4 Film on FTO for Rapid and Selective Non‐enzymatic Glucose Detection

A simple solution based deposition process has been used to fabricate Zn doped Co₃O₄ electrode as an electrocatalyst for non‐enzymatic oxidation of glucose. XRD, HRTEM, SEM, EELS, AFM, EIS was used to characterise the electrode. The addition of Zn as dopant on Co₃O₄ resulted in enhanced electrochemical performance of Zn:Co₃O₄ material compared to pristine Co₃O₄ due to increased charge transferability. The as prepared electrode showed fast response (<7 s) time, good sensitivity (193 μA mM⁻¹ cm⁻²) in the linear range of 5 μM–0.62 mM, good selectivity towards glucose at a relatively lower applied potential of +0.52 V in 0.1 M NaOH solution. A detection limit of ∼2 μM was measured for the Zn:Co₃O₄ electrode. The applied fabrication method resulted in good inter and intra electrode reproducibility as was shown by the lower relative standard deviation values (R.S.D). The electrode retained 70 % of initial current response after 30 days. Although the as prepared Zn:Co₃O₄ electrodes did not result in highest reported sensitivity, and lowest limit of detection; the ease of fabrication and scalability of production, good inter and intra electrode reproducibility makes it a potential candidate for commercial application as glucose sensor.     

Electrochemical Fabrication of Cobalt Oxides/Nanoporous Gold Composite Electrode and its Nonenzymatic Glucose Sensing Performance

A nonenzymatic glucose sensor was successfully established by electrochemically decorating cobalt oxides (CoO_x) on a nanoporous gold electrode (NPG) using cobalt hexacyanoferrate (CoHCF) as a precursor. It exhibited high sensitivity and long‐term stability as well as satisfactory quantification of glucose concentration in human serum samples. The morphology and surface analysis of the resulting CoO_x/NPG were carefully characterized. Two detection methods, cyclic voltammetry and amperometry, were employed to evaluate the performance of CoO_x/NPG towards glucose sensing in alkaline solution. Using cyclic voltammetry, at ?0.5 V, the glucose partial oxidation peak current is linear to the glucose concentration up to 14 mM with a sensitivity of 283.7 µA mM^?1 cm^?2. A linear amperometric response at 0.55 V was obtained in the glucose concentration range from 2 µM to 2 mM with a sensitivity of 2025 µA mM^?1 cm^?2 and a response time <3 s.     

A Novel Enzymatic Glucose Biosensor and Nonenzymatic Hydrogen Peroxide Sensor Based on (3‐Aminopropyl) Triethoxysilane Functionalized Reduced Graphene Oxide

In the present study, a novel enzymatic glucose biosensor using glucose oxidase (GOx) immobilized into (3‐aminopropyl) triethoxysilane (APTES) functionalized reduced graphene oxide (rGO‐APTES) and hydrogen peroxide sensor based on rGO‐APTES modified glassy carbon (GC) electrode were fabricated. Nafion (Nf) was used as a protective membrane. For the characterization of the composites, Fourier transform infrared spectroscopy (FTIR), X‐ray powder diffractometer (XRD), and transmission electron microscopy (TEM) were used. The electrochemical properties of the modified electrodes were investigated using electrochemical impedance spectroscopy, cyclic voltammetry, and amperometry. The resulting Nf/rGO‐APTES/GOx/GC and Nf/rGO‐APTES/GC composites showed good electrocatalytical activity toward glucose and H₂O₂, respectively. The Nf/rGO‐APTES/GC electrode exhibited a linear range of H₂O₂ concentration from 0.05 to 15.25 mM with a detection limit (LOD) of 0.017 mM and sensitivity of 124.87 μA mM⁻¹ cm⁻². The Nf/rGO‐APTES/GOx/GC electrode showed a linear range of glucose from 0.02 to 4.340 mM with a LOD of 9 μM and sensitivity of 75.26 μA mM⁻¹ cm⁻². Also, the sensor and biosensor had notable selectivity, repeatability, reproducibility, and storage stability.     

Facile synthesis of ultrafine Co3O4 nanocrystals embedded carbon matrices with specific skeletal structures as efficient non-enzymatic glucose sensors

A facile, effective, and environmentally friendly method has been adopted for the first time to prepare tiny Co₃O₄ nanocrystals embedded carbon matrices without using surfactants, harmful organic reagents or extreme conditions. Structural characterizations reveal that the size-controlled Co₃O₄ nanocrystals are uniformly dispersed on carbon matrices. Electrochemical measurements reveal that Co₃O₄-ordered mesoporous carbon (OMC) can more efficiently catalyze glucose oxidation and acquire better detection parameters compared with those for the Co₃O₄-macroporous carbon, Co₃O₄-reduced graphene oxide, and free Co₃O₄ nanoparticles (NPs) (such as: the large sensitivity (2597.5 μA cm⁻² mM⁻¹ between 0 and 0.8 mM and 955.9 μA cm⁻² mM⁻¹ between 0.9 and 7.0 mM), fast response time, wide linear range, good stability, and surpassingly selective capability to electroactive molecules or Cl⁻). Such excellent performances are attributed to the synergistic effect of the following three factors: (1) the high catalytic sites provided by the uniformly dispersed and size-controlled Co₃O₄ nanocrystals embedded on OMC; (2) the excellent reactant transport efficiency caused by the abundant mesoporous structures of OMC matrix: (3) the improved electron transport in high electron transfer rate (confinement of the Co₃O₄ NPs in nanoscale spaces ensured intimate contact between Co₃O₄ nanocrystals and the conducting OMC matrix). The superior catalytic activity and selectivity make Co₃O₄-OMC very promising for application in direct detection of glucose.     

Highly Oriented Nitrogen-doped Carbon Nanotube Integrated Bimetallic Cobalt Copper Organic Framework for Non-enzymatic Electrochemical Glucose and Hydrogen Peroxide Sensor

The hierarchical three-dimensional nitrogen-doped carbon nanotube anchored bimetallic cobalt copper organic framework (NCNT MOF CoCu) is successfully synthesized by the direct growth approach using the high-temperature carbonization of bimetallic cobalt copper organic framework (MOF CoCu-500). The as-prepared NCNT MOF CoCu nanostructure possesses high-level activity for both glucose and hydrogen peroxide (H₂O₂) sensing molecules. The cyclic voltammetry (CV) and chronoamperometry (CA) studies demonstrate excellent electrocatalytic performance for the oxidation of glucose with a linear range of 0.05 to 2.5 mM, high sensitivity of 1027 μA mM⁻¹cm⁻², and the lowest detection limit of 0.15 μM. Similarly, the NCNT MOF CoCu nanostructure showed significantly higher H₂O₂ activity with a linear range of 0.05 to 3.5 mM, high sensitivity of 639.5 μA mM⁻¹cm⁻², and the lowest detection limit of 0.206 μM. Thanks to its special hierarchical nanoarchitecture, homogeneous nitrogen-doped carbon nanotubes, and highly graphitized carbon, which may be increased the synergistic effect between bimetallic CoCu and NCNT in the organic framework. The potentially effective fabricated sensor was also used as a suitable probe for the detection of glucose and H₂O₂ in the analysis of the real samples.     

Nitrogen‐doped Hollow Co3O4 Nanofibers for both Solid‐state pH Sensing and Improved Non‐enzymatic Glucose Sensing

Nitrogen‐doped hollow cobalt oxide nanofibers (Co₃O₄ NFs) with both glucose catalytic activity and pH sensitivity were fabricated through core‐sheath electrospinning technique, followed by calcination. The as‐developed nitrogen‐doped hollow Co₃O₄ NFs were thoroughly characterized using various techniques, and then employed to fabricate a dual electrochemical sensor for both pH sensing and glucose sensing. The pH sensitivity of the developed nitrogen‐doped hollow Co₃O₄ NFs demonstrated a Nernst constant of 12.9–15.9 mV/pH in the pH range of 3.0～9.0 and 6.8–10.7 mV/pH in the pH range of 9.0～13.0, respectively. The developed hollow cobalt oxides nanofibers sensor also possesses glucose sensitivity of 87.67 μA mM^?1 cm^?2, the limit of detection of 0.38 μM (S/N=3), and an acceptable selectivity against several common interferents in non‐enzymatic glucose determination. High accuracy for monitoring glucose in human serum sample was also demonstrated. These features indicate that the as‐synthesized nitrogen‐doped hollow cobalt oxides nanofibers hold great potential in the development of a unique dual sensor for both solid‐state pH sensing and superior non‐enzymatic glucose sensing.     

Nanostructured NiCu LDHs/polypyrrole nanotubes composite for nonenzymatic glucose sensing in human serum

Nanostructured NiCu layered double hydroxides (NiCu LDHs) are synthesized in situ on polypyrrole nanotubes through convenient co-precipitation and hydrothermal synthesis. The nanostructured composite (NiCu LDHs/PPy) shows high electrocatalytic activities towards the glucose oxidation reaction in alkaline electrolyte so that a nonenzymatic glucose sensor is developed. It is demonstrated that the sensor offers a wide linear range from 1.5 μM to 1.0 mM with a high sensitivity of 525.8 μA mM⁻¹ cm⁻² and a low limit of detection of 66 nM (S/N = 3). The nonenzymatic sensor has been successfully applied to real blood samples for glucose monitoring with high accuracy.     

A Highly Sensitive and Selective Non-enzymatic Hydrogen Peroxide Sensor Based on Nanostructured Co3O4 Thin Films Using the Sol-gel Method

In this work we report an easy and efficient way to fabricate nanostructured cobalt oxide (Co₃O₄) thin films as a non-enzymatic sensor for H₂O₂ detection. Co₃O₄ thin films were grown on ITO glass substrates via the sol-gel method and characterized with several techniques including X-ray diffraction, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and optical absorbance. The Co₃O₄ thin films’ performance regarding hydrogen peroxide detection was studied in a 0.1 M NaOH solution using two techniques, cyclic voltammetry (CV) and amperometry. The films exhibited a high sensitivity of 1450 μA.mM⁻¹.cm⁻², a wide linear range from 0.05 μM to 1.1 mM, and a very low detection limit of 18 nM. Likewise, the Co₃O₄ thin films produced showed an exceptional stability and a high selectivity.     

Real‐time Selective Detection of Hydrogen Peroxide Based on a Tantalum Deposited Pencil Lead Electrode for Evaluation of Enzyme Activities

In this study, we have carried out electrodeposition of tantalum (Ta) nanostructures on pencil lead electrode in non‐aqueous media at room temperature by applying a constant potential. The deposited Ta on pencil lead was examined for the catalytic effect regarding hydrogen peroxide (H₂O₂) reduction with voltammetry and amperometry. Ta/pencil lead electrode exhibited amperometric sensitivity of 0.317 μA mM⁻¹ cm⁻² and fast response time of 0.75 s, where selective detection of H₂O₂ was fulfilled without interruption from common electroactive biomaterials such as O₂, uric acid, ascorbic acid, dopamine, acetamidophenol, and glucose. For practical applications, the dynamic concentration changes of H₂O₂ during catalase and glucose oxidase‐involved reactions, either eliminating or producing H₂O₂, were successfully traced in real time with as‐prepared electrode. From the kinetics study for catalase and glucose oxidase, we evaluated Michaelis constants (K _m^app) as 7.8 mM for catalase and 37 mM for glucose oxidase, respectively.     

Non‐enzymatic Fructose Sensor Based on Co3O4 Thin Film

In this study, we report on the selective of fructose on Co₃O₄ thin film electrode surface. A facile chemical solution deposition technique was used to fabricate Co₃O₄ thin film on fluorine doped tin oxide, FTO, glass. Electrode characterization was done using XRD, HRTEM, SEM, AFM, and EIS. The constructed sensor exhibited two distinctive linear ranges (0.021–1.74 mM; 1.74–∼15 mM) covering a wide linear range of up to ∼15 mM at an applied potential of +0.6 V vs Ag/AgCl in 0.1 M NaOH solution. The sensor demonstrated high, reproducible and repeatable (R.S.D of <5 %) sensitivity of 495 (lower concentration range) & 53 (higher concentration range) μA cm⁻² mM⁻¹. The sensor produced a low detection limit of ∼1.7 μM (S/N =3). The electrode was characterised by a fast response time of <6 s and long term stability. The repeatability and stability of the electrode resulted from the chemical stability of Co₃O₄ thin film. The sensor was highly selective towards fructose compared to the presence of other key interferences i. e. AA, AC, UA. The ease of the electrode fabrication coupled with good electrochemical activity makes Co₃O₄ thin film, a promising candidate for non‐enzymatic fructose detection.     

Facile Synthesis of Graphene/Cobalt Oxide Nanohexagons for the Selective Detection of Dopamine

This work presents a simple green approach for the chemical synthesis of cobalt oxide nano hexagons (Co₃O₄ NHs) with an average size of 160±40 nm incorporated graphene nanosheets (GR). The techniques used to confirm the formation of GR−Co₃O₄ NHs are transmission electron microscopy (TEM), energy‐dispersive X‐ray spectroscopy (EDX), and X‐ray diffraction spectroscopy (XRD). The dopamine (DA) sensor was fabricated by drop casting GR−Co₃O₄ NHs on the pre‐cleaned glassy carbon electrode (GCE). GR−Co₃O₄ modified GCE displayed a sensitive and selective electrochemical determination of DA compared to only GR and Co₃O₄ NHs modified GCE. Our fabricated sensor showed a wide linear range from 0.2 to 3443 μM with low limit of detection (84 nM) towards the determination of DA. The sensitivity of our fabricated sensor was calculated to be 108 μA mM⁻¹ cm⁻². As well, a significant storage stability, repeatability and reproducibility were attained by GR−Co₃O₄ NHs modified GCE. Human urine samples were targeted for the demonstration of practicality of our sensor.     

Glucose Biosensors Based on Electrodes Modified with Ferrocene Derivatives Intercalated into Mg/Al Layered Double Hydroxides

Two amperometric biosensors based on glassy carbon electrodes (GC) modified with Mg/Al layered double hydroxides (LDHs) containing ferrocene‐carboxylate (Fc? CO₂H) or ferrocene‐sulfonate (Fc? SO₃H), as interlayer anions, and glucose oxidase (GOx) are presented. Amperometric detection of glucose involves the electrochemical oxidation of H₂O₂ mediated by the ferrocene derivative. Optimization of the biosensors construction and of the operative conditions was investigated and is discussed herein. The performances of the two biosensors were evaluated by chronoamperometry, working at low anodic potentials (+0.400 V for Fc? CO₂H and +0.500 V for Fc? SO₃H vs. SCE). The linearity extended up to 1.5 mM and 10.0 mM in batch and in flow conditions, respectively, for both biosensors, whereas the sensitivity was higher for the one based on Fc? CO₂H (4.8±0.3 versus 2.0±0.3 μA mM^?1cm^?2 in batch mode, and 63.9±0.4 versus 25.8±0.4 μA mM^?1cm^?2 in flow mode). The biosensors display rapid response time (less than 20 s), good reproducibility, as well as good operational stability. Glucose can be accurately determined in the presence of the most common interferences that coexist in blood serum if an oxidative membrane containing nanoparticles of MnO₂ is applied on the biosensors' surface.     

NiMoO4 nanofibres designed by electrospining technique for glucose electrocatalytic oxidation

Electrochemical oxidation of glucose is the guarantee to realize nonenzymatic sensing of glucose, but greatly hindered by the slow kinetics of its oxidation process. Herein, various nanomaterials were designed as catalysts to accelerate glucose oxidation reaction. However, how to effectively build an excellent platform for promoting the glucose oxidation is still a great challenge. In our work, 1D CaMoO₄ and NiMoO₄ nanofibres with same morphologies and sub-microstructures were fabricated by electrospinning technique in the first time, and explored to modify the detection electrodes of nonenzymatic glucose sensors. The electrochemical results indicated that the NiMoO₄ based sensor exhibited a good catalytic activity toward glucose including the low response potential (0.5 V), high sensitivity(193.8 μA mM⁻¹ cm⁻²) with a linear response region of 0.01–8 mM, low detection limit (4.6 μM) and fast response time (2 s), all of which are superior to the corresponding values of CaMoO₄ nanofibres and even higher than those of most reported NiO and Co₃O₄ catalysts, which is due to the NiMoO₄ nanofibres are not only advantageous to electron transfer, but can mediated the electrocatalytic reaction of glucose. This work should provide a new pathway for the design of advanced glucose catalysts for nonenzymatic sensor.     

The Hybrid of Gold Nanoparticles and 3D Flower‐like MnO2 Nanostructure with Enhanced Activity for Detection of Hydrogen Peroxide

3D Flower‐like manganese dioxide (MnO₂) nanostructure with the ability of catalysis for hydrogen peroxide (H₂O₂) and super large area that can support gold nanoparticles (AuNPs) with enhanced activity of electron transfer have been developed. The nanostructure of hybrids was prepared by directly mixing citric‐capped AuNPs and 3‐aminopropyltriethoxysilane (3‐APTES)‐capped nano‐MnO₂ using an electrostatic adsorption strategy. The Au‐MnO₂ composite was extensively characterized by scanning electron microscope (SEM), X‐ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), the Brunauer‐Emmett‐Teller (BET) method and X‐ray photoemission spectroscopy (XPS). Electrochemical properties were evaluated through cyclic voltammetry (CV) and amperometric method. The prepared sensor showed excellent electrochemical properties towards H₂O₂ with a wide linear range from 2.5×10⁻³∼1.39 mM and 3.89∼13.89 mM. The detection limit is 0.34 μM (S/N=3) with the sensitivities of 169.43 μA mM⁻¹ cm⁻² and 55.72 μA mM⁻¹ cm⁻². The detection of real samples was also studied. The result exhibited that the prepared sensor can be used for H₂O₂ detection in real samples.     

MOF‐Derived Spinel NiCo2O4 Hollow Nanocages for the Construction of Non‐enzymatic Electrochemical Glucose Sensor

Non‐enzymatic glucose sensor is greatly expected to take over its enzymatic counterpart in the future. In this paper, we reported on a facile strategy to construct a non‐enzymatic glucose sensor by use of NiCo₂O₄ hollow nanocages (NiCo₂O₄ HNCs) as catalyst, which was derived from Co‐based zeolite imidazole frame (ZIF‐67). The NiCo₂O₄ HNCs modified glassy carbon electrode (NiCo₂O₄ HNCs/GCE), the key component of the glucose sensor, showed highly electrochemical catalytic activity towards the oxidation of glucose in alkaline media. As a result, the proposed non‐enzymatic glucose sensor afforded excellent analytical performances assessed with the aid of cyclic voltammetry and amperometry (i–t). A wide linear range spanning from 0.18 μΜ to 5.1 mM was achieved at the NiCo₂O₄ HNCs/GCE with a high sensitivity of 1306 μA mM^?1 cm^?2 and a fast response time of 1 s. The calculated limit of detection (LOD) of the sensor was as low as 27 nM (S/N=3). Furthermore, it was demonstrated that the non‐enzymatic glucose sensor showed considerable anti‐interference ability and excellent stability. The practical application of the sensor was also evaluated by determination of glucose levels in real serum samples.     

Facile synthesis of cobalt oxide/reduced graphene oxide composites for electrochemical capacitor and sensor applications

Reduced graphene oxide sheets decorated with cobalt oxide nanoparticles (Co₃O₄/rGO) were produced using a hydrothermal method without surfactants. Both the reduction of GO and the formation of Co₃O₄ nanoparticles occurred simultaneously under this condition. At the same current density of 0.5 A g⁻¹, the Co₃O₄/rGO nanocomposites exhibited much a higher specific capacitance (545 F g⁻¹) than that of bare Co₃O₄ (100 F g⁻¹). On the other hand, for the detection of H₂O₂, the peak current of Co₃O₄/rGO was 4 times higher than that of Co₃O₄. Moreover, the resulting composite displayed a low detection limit of 0.62 μM and a high sensitivity of 28,500 μA mM⁻¹cm⁻² for the H₂O₂ sensor. These results suggest that the Co₃O₄/rGO nanocomposite is a promising material for both supercapacitor and non-enzymatic H₂O₂ sensor applications.     

α‐Fe2O3 Film with Highly Photoactivity for Non‐enzymatic Photoelectrochemical Detection of Glucose

A non‐enzyme photoelectrochemical (PEC) glucose sensor based on α‐Fe₂O₃ film is investigated. The α‐Fe₂O₃ film was fabricated via a simple spin coating method. The proposed glucose sensor exhibits good selectivity, a fast response time of <5 s, a linear range of 0.05 to 6.0 mM, sensitivity of 17.23 μA mM^?1 cm^?2 and a detection limit of 0.05 μM. Meanwhile, the excellent performances of the α‐Fe₂O₃ sensor were obtained in reproducibility and the long‐term stability under ambient condition. The linear amperometric response of the sensor covers the glucose levels in physiological and clinical for diabetic patients. Therefore, this non‐enzyme PEC sensor based on α‐Fe₂O₃ film has a great potential application in the development of glucose sensors.     

Bimetallic CuCo Derived from Prussian Blue Analogue for Nonenzymatic Glucose Sensing

Bimetallic CuCo composites are prepared by calcinating copper hexacyanocobaltate precursor in N₂ atmosphere. The CuCo modified electrodes are fabricated for nonenzymatic glucose sensing in the alkaline electrolyte. The glucose can be directly electro-oxidized on the surface of the electrode catalyst mediated by the redox couples of Cu and Co. The optimal glucose sensor exhibits a high sensitivity (567 μA ⋅ mM⁻¹ ⋅ cm⁻²) in the range up to 825 μM with a detection limit of 3 μM and acceptable selectivity. The sensor can also be applied in serum samples. This work provides a facile and easily-scalable synthesis method of electrocatalysts for nonenzymatic glucose sensors.     

Novel Nonenzymatic Hydrogen Peroxide Sensor Based on Ag/Cu2O Nanocomposites

The nanocomposites of Ag nanoparticles supported on Cu₂O were prepared and used for fabricating a novel nonenzymatic H₂O₂ sensor. The morphology and composition of the nanocomposites were characterized using the scanning electron microscope (SEM), transmission electron microscope (TEM), energy‐dispersive X‐ray spectrum (EDX) and X‐ray diffraction spectrum (XRD). The electrochemical investigations indicate that the sensor possesses an excellent performance toward H₂O₂. The linear range is estimated to be from 2.0 μM to 13.0 mM with a sensitivity of 88.9 μA mM^?1 cm^?2, a response time of 3 s and a low detection limit of 0.7 μM at a signal‐to‐noise ratio of 3. Additionally, the sensor exhibits good anti‐interference.