Reducing the Charge Carrier Transport Barrier in Functionally Layer‐Graded Electrodes

Lithium‐ion batteries (LIBs) are primary energy storage devices to power consumer electronics and electric vehicles, but their capacity is dramatically decreased at ultrahigh charging/discharging rates. This mainly originates from a high Li‐ion/electron transport barrier within a traditional electrode, resulting in reaction polarization issues. To address this limitation, a functionally layer‐graded electrode was designed and fabricated to decrease the charge carrier transport barrier within the electrode. As a proof‐of‐concept, functionally layer‐graded electrodes composing of TiO₂(B) and reduced graphene oxide (RGO) exhibit a remarkable capacity of 128 mAh g⁻¹ at a high charging/discharging rate of 20 C (6.7 A g⁻¹), which is much higher than that of a traditionally homogeneous electrode (74 mAh g⁻¹) with the same composition. This is evidenced by the improvement of effective Li ion diffusivity as well as electronic conductivity in the functionally layer‐graded electrodes.     

Hierarchical Carbon Nanowire/Ni@MnO2 Nanocomposites for High-Performance Asymmetric Supercapacitors

A 3D hierarchical carbon cloth/nitrogen-doped carbon nanowires/Ni@MnO₂ (CC/N-CNWs/Ni@MnO₂) nanocomposite electrode was rationally designed and prepared by electrodeposition. The N-CNWs derived from polypyrrole (PPy) nanowires on the carbon cloth have an open framework structure, which greatly increases the contact area between the electrode and electrolyte and provides short diffusion paths. The incorporation of the Ni layer between the N-CNWs and MnO₂ is beneficial for significantly enhancing the electrical conductivity and boosting fast charge transfer as well as improving the charge-collection capacity. Thus, the as-prepared 3D hierarchical CC/N-CNWs/Ni@MnO₂ electrode exhibits a higher specific capacitance of 571.4 F g⁻¹ compared with those of CC/N-CNWs@MnO₂ (311 F g⁻¹), CC/Ni@MnO₂ (196.6 F g⁻¹), and CC@MnO₂ (186.1 F g⁻¹) at 1 A g⁻¹ and remarkable rate capability (367.5 F g⁻¹ at 10 A g⁻¹). Moreover, asymmetric supercapacitors constructed with CC/N-CNWs/Ni@MnO₂ as cathode material and activated carbon as anode material deliver an impressive energy density of 36.4 W h kg⁻¹ at a power density of 900 W kg⁻¹ and a good cycling life (72.8 % capacitance retention after 3500 cycles). This study paves a low-cost and simple way to design a hierarchical nanocomposite electrode with large surface area and superior electrical conductivity, which has wide application prospects in high-performance supercapacitors.     

A Porphyrin Complex as a Self‐Conditioned Electrode Material for High‐Performance Energy Storage

The novel functionalized porphyrin [5,15‐bis(ethynyl)‐10,20‐diphenylporphinato]copper(II) (CuDEPP) was used as electrodes for rechargeable energy‐storage systems with an extraordinary combination of storage capacity, rate capability, and cycling stability. The ability of CuDEPP to serve as an electron donor or acceptor supports various energy‐storage applications. Combined with a lithium negative electrode, the CuDEPP electrode exhibited a long cycle life of several thousand cycles and fast charge–discharge rates up to 53 C and a specific energy density of 345 Wh kg⁻¹ at a specific power density of 29 kW kg⁻¹. Coupled with a graphite cathode, the CuDEPP anode delivered a specific power density of 14 kW kg⁻¹. Whereas the capacity is in the range of that of ordinary lithium‐ion batteries, the CuDEPP electrode has a power density in the range of that of supercapacitors, thus opening a pathway toward new organic electrodes with excellent rate capability and cyclic stability.     

Perovskite SrCo0.9Nb0.1O3−δ as an Anion‐Intercalated Electrode Material for Supercapacitors with Ultrahigh Volumetric Energy Density

We have synthesized and characterized perovskite‐type SrCo_0.9Nb_0.1O_3−δ (SCN) as a novel anion‐intercalated electrode material for supercapacitors in an aqueous KOH electrolyte, demonstrating a very high volumetric capacitance of about 2034.6 F cm⁻³ (and gravimetric capacitance of ca. 773.6 F g⁻¹) at a current density of 0.5 A g⁻¹ while maintaining excellent cycling stability with a capacity retention of 95.7 % after 3000 cycles. When coupled with an activated carbon (AC) electrode, the SCN/AC asymmetric supercapacitor delivered a specific energy density as high as 37.6 Wh kg⁻¹ with robust long‐term stability.     

Intertwined Titanium Carbide MXene within a 3 D Tangled Polypyrrole Nanowires Matrix for Enhanced Supercapacitor Performances

The exploration of the rational design and synthesis of unique and robust architectured electrodes for the high capacitance, rate capability, and stability of supercapacitors is crucial to the future of energy storage technology. Herein, an in situ synthesis of multilayered titanium carbide MXene tightly caging within a 3 D conducting tangled polypyrrole (PPy) nanowire (NW) network is proposed as an effective strategy to prevent the aggregation of MXene, profoundly enhancing the electrochemical performance of the supercapacitor. Owing to the beneficial effects of an ideal 3 D interconnected porous structure and high electrical conductivity, the obtained electrode exhibits fast charge and ion transport kinetics as well as full usage of active material. As expected, the 3 D Ti₃C₂T_x@PPY NW exhibits a specific capacitance five times higher than that of pristine MXene (610 F g⁻¹), a good rate capability up to a current density of 25 A g⁻¹, and excellent stability with 100 % retention after 14 000 cycles at 4 A g⁻¹, outperforming the known state-of-the-art MXene-based supercapacitor. Our work provides a facile method for enhancing the performance of MXene-based energy storage devices.     

An Insoluble Benzoquinone‐Based Organic Cathode for Use in Rechargeable Lithium‐Ion Batteries

Application of organic electrode materials in rechargeable batteries has attracted great interest because such materials contain abundant carbon, hydrogen, and oxygen elements. However, organic electrodes are highly soluble in organic electrolytes. An organic electrode of 2,3,5,6‐tetraphthalimido‐1,4‐benzoquinone (TPB) is reported in which rigid groups coordinate to a molecular benzoquinone skeleton. The material is insoluble in aprotic electrolyte, and demonstrates a high capacity retention of 91.4 % (204 mA h g⁻¹) over 100 cycles at 0.2 C. The extended π‐conjugation of the material contributes to enhancement of the electrochemical performance (155 mA h g⁻¹ at 10 C). Moreover, density functional theory calculations suggest that favorable synergistic reactions between multiple carbonyl groups and lithium ions can enhance the initial lithium ion intercalation potential. The described approach may provide a novel entry to next‐generation organic electrode materials with relevance to lithium‐ion batteries.     

Design and green synthesis of 1-(4-ferrocenylbutyl)piperazine chemically grafted reduced graphene oxide for supercapacitor application

In this paper, we report the green synthesis of 1-(4-ferrocenylbutyl)piperazine chemically grafted rGO (P.Fc/rGO) as a battery-type supercapacitor electrode material. For this purpose, initially, the ability of the aqueous Damson fruit extract is investigated in the reduction reaction of graphene oxide (GO). 1-(4-ferrocenylbutyl)piperazine (P.Fc) is synthesized via nucleophilic substitution reaction of piperazine with as-synthesized 4-chlorobutylferrocene. In continue, P. Fc is incorporated to GO by ring-opening reaction of epoxide groups on the GO surface. In the next step, the modified reduction method by aqueous Damson fruit extract was used to prepare the P.Fc/rGO from P.Fc/GO. The prepared materials were characterized by various techniques including FT-IR, Uv–vis, XRD, SEM, EDX, and BET. N₂ adsorption–desorption data of P.Fc/rGO nanocomposite shows that the surface area is 37.746 m² g⁻¹. The capability of P.Fc/rGO nanocomposite for using as an energy storage electrode material in battery-type supercapacitor was examined by investigation of its electrochemical behavior by CV, EIS, and GCD measurements. The charge storage capacity of 1,102 mAh g⁻¹ is achieved at 2.5 A g⁻¹. This nanocomposite shows 89% retention of charge storage capacity after 2000 CV cycles.     

Implementation of a Simple Nanostructured Bio‐electrode with Immobilized Rhus Vernicifera Laccase for Oxygen Sensing Applications

In this work a simple nanostructured direct‐electron transfer bio‐electrode based on tree laccase from Rhus vernicifera is described. The electrode was implemented on a 2 mm diameter graphite mine casted with a reduced graphene surface presenting the specific capacitance of 195.8 F g⁻¹. About 10 μl of mixture between 25 mg mL⁻¹ laccase suspension and 5 mg mL⁻¹ single‐walled carbon nanotubes in 2 % SDS is dropped over the surface followed by 5 μl of the biological friendly tetrakis(2,3‐dihydroxypropyl)‐silane monomer sol to provide physical entrapment in a silica matrix after gelation. The rigidity of enzyme encapsulation allowed to obtain a constant enzyme turnover of about 16 min⁻¹ in the extended pH range of 6.0‐7.5, being the activity almost proportional to the temperature used in the interval between 25 and 40 °C. The graphite‐graphene/SWCNT‐laccase/sol‐gel electrode enabled a proportional response to molecular oxygen up to the concentration of 0.45 mmol L⁻¹ and is capable to generate the maximum power of 4.5 μW cm⁻² at 0.250 V vs the AgCl/Ag reference electrode in quiescent oxygen saturated solution.     

Polyaniline‐Stabilized Intertwined Network‐like Ferrocene/Graphene Nanoarchitecture for Supercapacitor Application

The present work highlights the effective H–π interaction between metallocenes (ferrocene; Fc) and graphene and their stabilization in the presence of polyaniline (PANI) through π–π interactions. The PANI‐stabilized Fc@graphene nanocomposite (FcGA) resembled an intertwined network‐like morphology with high surface area and porosity, which could make it a potential candidate for energy‐storage applications. The relative interactions between the components were assessed through theoretical (DFT) calculations. The specific capacitance calculated from galvanostatic charging/discharging indicated that the PANI‐stabilized ternary nanocomposite exhibited a maximum specific capacitance of 960 F g⁻ at an energy density of 85 Wh Kg⁻¹ and a current density of 1 A g⁻. Furthermore, electrochemical impedance spectroscopy (EIS) analysis confirmed the low internal resistance of the as‐prepared nanocomposites, which showed improved charge‐transfer properties of graphene after incorporation of Fc and stabilization with PANI. Additionally, all electrodes were found to be stable up to 5000 cycles with a specific capacitance retention of 86 %, thus demonstrating the good reversibility and durability of the electrode material.     

Electrochemical Evaluation of Titanium (IV) Oxide/Polyacrylonitrile Electrospun Discharged Battery Coals as Supercapacitor Electrodes

The TiO₂ nanoparticles are electrospun with polyacrylonitrile (PAN) polymer solution onto the discharged battery coal (DBC) electrode and the results are evaluated as a supercapacitor. The morphology and chemical composition of the synthesized TiO₂ nanoparticles and PAN+TiO₂ nanocomposite fibers were characterized by Scanning electron microscopy, thermogravimetry and FTIR analysis. Supercapacitor measurements and electrochemical characterizations of the electrodes examined by cyclic voltammetry and electrochemical impedance spectroscopy. Electrochemical measurements showed that the best current value was obtained from PAN and TiO₂ coated DBC. The performances of both PAN and PAN+TiO₂ coated DBC electrodes were investigated as supercapacitors. PAN+TiO₂/DBC showed the best specific capacitance value of 156.00 F g⁻¹ and PAN/DBC showed 74.93 F g⁻¹. In addition, PAN+TiO₂/DBC exhibited reliable stability performance over 2000.00 cycles.     

Pitch-Based Laminated Carbon Formed by Pressure Driving at Low Temperature as High-Capacity Anodes for Lithium Energy Storage Systems

Pitch has been used to prepare electrodes by high-temperature heat treatments for supercapacitors, lithium-ion batteries, on account of its rich aromatic ring structure. Here, the toluene-soluble component of pitch is used to prepare a kind of laminated carbon. This was realized by a template-free synthesis at low temperature with the addition of pressure. The toluene-soluble component has a small molecular weight, which makes the thermal deformation ability stronger and then enhances the orientation of the carbon layer with the help of pressure. The prepared anode exhibits a splendid electrochemical performance compared with the traditional graphite anode. A high stable capacity of approximately 550 mAh g⁻¹ at 50 mA g⁻¹, which is much higher than graphite (372 mAh g⁻¹), is obtained. Also, when the current density is up to 2 A g⁻¹, the capacity is about 150 mAh g⁻¹. Surprisingly, it also delivers a superior cycling performance. And when used as the anode/cathode electrode for lithium-ion capacitors, a high energy density can be obtained. The present work offers an opportunity to utilize the pitch source in lithium energy storage with promising cycle life, high energy/power density, and low cost.     

Electrodeposition of MnO2 nanowires on carbon nanotube paper as free-standing,flexible electrode for supercapacitors

MnO₂ nanowires were electrodeposited onto carbon nanotube (CNT) paper by a cyclic voltammetric technique. The as-prepared MnO₂ nanowire/CNT composite paper (MNCCP) can be used as a flexible electrode for electrochemical supercapacitors. Electrochemical measurements showed that the MNCCP electrode displayed specific capacitances as high as 167.5 F g⁻¹ at a current density of 77 mA g⁻¹. After 3000 cycles, the composite paper can retain more than 88% of initial capacitance, showing good cyclability. The CNT paper in the composite acted as a good conductive and active substrate for flexible electrodes in supercapacitors, and the nanowire structure of the MnO₂ could facilitate the contact of the electrolyte with the active materials, and thus increase the capacitance.     

β‐Co(OH)2 Nanosheets: A Superior Pseudocapacitive Electrode for High‐Energy Supercapacitors

In this work, β‐Co(OH)₂ nanosheets are explored as efficient pseudocapacitive materials for the fabrication of 1.6 V class high‐energy supercapacitors in asymmetric fashion. The as‐synthesized β‐Co(OH)₂ nanosheets displayed an excellent electrochemical performance owing to their unique structure, morphology, and reversible reaction kinetics (fast faradic reaction) in both the three‐electrode and asymmetric configuration (with activated carbon, AC). For example, in the three‐electrode set‐up, β‐Co(OH)₂ exhibits a high specific capacitance of ∼675 F g⁻¹ at a scan rate of 1 mV s⁻¹. In the asymmetric supercapacitor, the β‐Co(OH)₂∥AC cell delivers a maximum energy density of 37.3 Wh kg⁻¹ at a power density of 800 W kg⁻¹. Even at harsh conditions (8 kW kg⁻¹), an energy density of 15.64 Wh kg⁻¹ is registered for the β‐Co(OH)₂∥AC assembly. Such an impressive performance of β‐Co(OH)₂ nanosheets in the asymmetric configuration reveals the emergence of pseudocapacitive electrodes towards the fabrication of high‐energy electrochemical charge storage systems.     

One-Pot Hydrothermal Synthesis of Ternary 1T-MoS2/Hexa-WO3/Graphene Composites for High-Performance Supercapacitors

A new ternary composite of 1T-molybdenum disulfide, hexagonal tungsten trioxide, and reduced graphene oxide (M-W-rGO) is synthesized by using a one-pot hydrothermal process. The synergetic effect of 1T-MoS₂ and hexa-WO₃ nanoflowers improves the electrochemical performance for supercapacitors by inducing additional active sites and hexagonal tunnels, respectively, which lead to high storage capacity and easy transfer of electrolyte ions. The ternary M-W-rGO composite has a high specific capacitance of 836 F g⁻¹ at 1 A g⁻¹, which is nearly twice that of binary composites of M-rGO and W-rGO with high capacitance retention of 86.35 % after 3000 cycles at a high current density of 5 A g⁻¹. This study provides a new ternary composite that can be used as an electrode material for high-performance supercapacitors.     

A Microwave Synthesis of Mesoporous NiCo2O4 Nanosheets as Electrode Materials for Lithium‐Ion Batteries and Supercapacitors

A facile microwave method was employed to synthesize NiCo₂O₄ nanosheets as electrode materials for lithium‐ion batteries and supercapacitors. The structure and morphology of the materials were characterized by X‐ray diffraction, field‐emission scanning electron microscopy, transmission electron microscopy and Brunauer–Emmett–Teller methods. Owing to the porous nanosheet structure, the NiCo₂O₄ electrodes exhibited a high reversible capacity of 891 mA h g^?1 at a current density of 100 mA g^?1, good rate capability and stable cycling performance. When used as electrode materials for supercapacitors, NiCo₂O₄ nanosheets demonstrated a specific capacitance of 400 F g^?1 at a current density of 20 A g^?1 and superior cycling stability over 5000 cycles. The excellent electrochemical performance could be ascribed to the thin porous structure of the nanosheets, which provides a high specific surface area to increase the electrode–electrolyte contact area and facilitate rapid ion transport.     

Oxygen Vacancies-rich Manganese Oxide with Flower-like Nanosheets for High Performance Supercapacitors

Here, flower-like manganese oxide with enriched oxygen vacancies were reported for high performance supercapacitors. The moderate oxygen-vacancy were achieved by controlling annealing atmosphere. Benefiting from improving the conductivity and the density of active sites, MnO_x−Ar sample as an electrode material has remarkable specific capacity (339 mAh g⁻¹ at 0.5 A g⁻¹), extraordinary rate capability (90 % capacity retention at 1 A g⁻¹), and good cycling property (90 % capacity retention at 1 A g⁻¹ after 5000 cycles). Additionally, the asymmetric supercapacitor (ASC) was assembled which used the MnO_x−Ar sample as cathode and Kochen Black (KB) as anode, which displayed a remarkable energy density (16 Wh kg⁻¹) at a large power density (7593 W kg⁻¹). These results, on the one hand, further expand the application of MnO₂-based materials, and on the other hand, offer a new perspective for the oxygen non-stoichiometry in material electrochemistry.     

Electrochromic Poly(chalcogenoviologen)s as Anode Materials for High‐Performance Organic Radical Lithium‐Ion Batteries

A series of electrochromic electron‐accepting poly(chalcogenoviologen)s with multiple, stable, and reversible redox centers were used as anodic materials in organic radical lithium‐ion batteries (ORLIBs). The introduction of heavy atoms (S, Se, and Te) into the viologen scaffold significantly improved the capacity and cycling stability of the ORLIBs. Notably, the poly(Te‐BnV) anode was able to intercalate 20 Li ions and showed higher conductivity and insolubility in the electrolyte, thus contributing to a reversible capacity of 502 mAh g^?1 at 100 mA g^?1 when the Coulombic efficiency approached 100 %. The charged/discharged state of flexible electrochromic batteries fabricated from these anodic materials could be monitored visually owing to the unique electrochromic and redox properties of the materials. This study opens a promising avenue for the development of organic polymer‐based electrodes for flexible hybrid visual electronics.     

Organic Thiocarboxylate Electrodes for a Room‐Temperature Sodium‐Ion Battery Delivering an Ultrahigh Capacity

Organic room‐temperature sodium‐ion battery electrodes with carboxylate and carbonyl groups have been widely studied. Herein, for the first time, we report a family of sodium‐ion battery electrodes obtained by replacing stepwise the oxygen atoms with sulfur atoms in the carboxylate groups of sodium terephthalate which improves electron delocalization, electrical conductivity and sodium uptake capacity. The versatile strategy based on molecular engineering greatly enhances the specific capacity of organic electrodes with the same carbon scaffold. By introducing two sulfur atoms to a single carboxylate scaffold, the molecular solid reaches a reversible capacity of 466 mAh g⁻¹ at a current density of 50 mA g⁻¹. When four sulfur atoms are introduced, the capacity increases to 567 mAh g⁻¹ at a current density of 50 mA g⁻¹, which is the highest capacity value reported for organic sodium‐ion battery anodes until now.     

Comparative Study of the Supercapacitive Performance of Three Ferrocene-Based Structures: Targeted Design of a Conductive Ferrocene-Functionalized Coordination Polymer as a Supercapacitor Electrode

As redox-active based supercapacitors are known as highly desirable next-generation supercapacitor electrodes, the targeted design of two ferrocene-functionalized (Fc(COOH)₂) clusters based on coinage metals, [(PPh₃)₂AgO₂CFcCO₂Ag(PPh₃)₂]₂ ⋅ 7 CH₃OH (SC₁: super capacitor) and [(PPh₃)₃CuO₂CFcCO₂Cu(PPh₃)₃] ⋅ 3 CH₃OH (SC₂), is reported. Both structures are fully characterized by various techniques. The structures are utilized as energy storage electrode materials, giving 130 F g⁻¹ and 210 F g⁻¹ specific capacitance at 1.5 A g⁻¹ in Na₂SO₄ electrolyte, respectively. The obtained results show that the presence of Cu^I instead of Ag^I improves the supercapacitive performance of the cluster. Further, to improve the conductivity, the PSC₂ ([(PPh₃)₂CuO₂CFcCO₂]_∞), a polymeric structure of SC₂, was synthesized and used as an energy storage electrode. PSC₂ displays high conductivity and gives 455 F g⁻¹ capacitance at 3 A g⁻¹. The PSC₂ as a supercapacitor electrode presents a high power density (2416 W kg⁻¹), high energy density (161 Wh kg⁻¹), and long cycle life over 4000 cycles (93 %). These results could lead to the amplification of high-performance supercapacitors in new areas to develop real applications and stimulate the use of the targeted design of coordination polymers without hybridization or compositions with additive materials.     

A novel conjugated porous polymer based on triazine and imide as cathodes for sodium storage

Organic electrode materials have attracted more and more attention for sodium-ion batteries (SIBs) that are regarded as one of the most promising alternatives of lithium-ion batteries, because they can endure the storage of large sodium ions (with a larger radius than that of lithium ions) without obvious volume change. Herein, we report a novel conjugated porous polymer (TPIP) based on triazine and imide as cathodes material for SIBs. TPIP has abundant redox-active sites, good thermal stability (400°C) and large specific surface area (306 m² g⁻¹). As a result, TPIP electrode delivered a specific capacity of 120 mAh g⁻¹ after 50 cycles at a current density of 0.1 A g⁻¹ and 85 mAh g⁻¹ after 150 cycles at a current density of 1.0 A g⁻¹. Ex-situ X-ray photoelectron spectra and Fourier transform infrared spectra showed that the TPIP electrodes reversibly stored three sodium ions per unit through the triazine rings and half of the carbonyl groups. These results deepen our understanding of charge storage mechanisms of polymers with triazine and imide units and will provide guidance for the future design of electrode materials for high-performance SIBs.