Electrochemical Characteristics and Electrosensing of an Antiviral Drug,Entecavir via Synergic Effect of Graphene Oxide Nanoribbons and Ceria Nanorods

A sensitive electrochemical sensor was fabricated based on ceria‐graphene oxide nanoribbons composite (CeO₂‐GONRs) for an antiviral drug, entecavir (ETV). It was characterized by SEM, EDAX, AFM, IR and Raman spectroscopic techniques. The electrochemical behaviour of ETV was investigated by cyclic voltammetric, differential pulse voltammetric (DPV), linear sweep voltammetric (LSV) and square wave voltammetric (SWV) methods at CeO₂‐GONRs modified glassy carbon electrode. Good linearity was observed between the peak current and concentration of ETV in the range of 0.51 ‐ 100 μM with a detection limit of 0.042 μM in DPV method, 2.1 – 61.1 μM with a detection limit of 0.7 μM in LSV method and 0.1 ‐ 80 μM with a detection limit of 68.1 nM in SWV method. The proposed sensitive DPV method was successfully applied for the determination ETV in tablets and biological samples.     

Differential Pulse Voltammetric Determination and Application of Square‐Wave Voltammetry of yRNA on a CPB‐Cellulose Modified Electrode

Electrochemical behavior of remarkably low levels of Ribonucleic acid yeast (yRNA) is studied through differential pulse voltammetry (DPV), and kinetic parameters of the electrochemical reaction have also been calculated through square‐wave voltammetry (SWV), based on immobilization of yRNA on the surface of a CPB‐cellulose modified electrode. YRNA/ CPB‐cellulose/ITO conductive glass electrode is demonstrated by Infrared reflect (IR) and electrochemical impedance spectroscopy (EIS). The oxidation peak potential of yRNA shifts negatively with increasing pH. The peak currents decrease gradually in successive scans and no corresponding reduction peaks occur, indicating that oxidation process of yRNA is completely irreversible. Variables influencing DPV response of yRNA, such as pH, pulse amplitude and electrolyte concentration, are explored and optimized. Peak currents are proportional to the concentration of yRNA in the range of 0.1 μg mL^?1–1.0 μg mL^?1, and the linear regression coefficient equals 0.9923. The detection limit for yRNA is 1.0×10^?10 g mL^?1. Interferences of L ‐cysteine, L ‐alanine, Hemoglobin, Uridine 5′‐monophosphate, Guanosine 5′‐monophosphate, Adenosine 5′‐triphosphate and some metal ions (Co³⁺, Cr³⁺, Ni²⁺, Hg²⁺, Zn²⁺, etc) are negligible. The methods adopted here are more sensitive and selective than currently applied techniques and overcome the drawback of absorption spectroscopy arising from a strong interference due to other UV‐absorbing substances.     

Electrochemical Oxidation of Phenothiazine Derivatives at Glassy Carbon Electrodes and Their Differential Pulse and Square‐wave Voltammetric Determination in Pharmaceuticals

Abstract

Three 2,10‐disubstituted phenothiazines—chlorpromazine hydrochloride (CPM), thioridazine hydrochloride (TR) and propericiazine (PRC)—were electrochemically studied in various buffer systems at different pH values, using a glassy carbon electrode. The substances were electrochemically oxidized at potential range 0.55–0.75 V. The oxidation was reversible and exhibited diffusion‐controlled process. The mechanism of the oxidation process is discussed. According to the linear relation between peak current and concentration, differential pulse voltammetry (DPV) and square wave voltammetry (SWV) methods for quantitative determination of chlorpromazine and propericiazine in 0.1 M HClO₄, and thioridazine in pH 2 phosphate buffer, was applied. Both the repeatability and reproducibility of the methods were also determined for all studied substances. The developed procedures were successfully applied to the determination of chlorpromazine and thioridazine in pharmaceutical dosage forms.     

Determination of some β‐Blockers by Electrochemical Detection on Polycrstalline Gold Electrode after Solid Phase Extraction (SPE)

The electroanalytical characterization and determination of three selected β‐blocker agents, namely propranolol, atenolol and nadolol using cyclic voltammetry and differential pulse voltammetry (DPV) in phosphate buffer solution (pH 2.5) plus 22 % acetonitrile (ACN), was described. The analytes were characterized through their electrooxidation processes on polycrystalline gold electrodes. The analytical determination of the selected molecules was performed using the differential pulse voltammetry (DPV) at pH 2.5. Under DPV conditions, the detection limits (LODs) ranged between 5 μM and 20 μM for propranolol and atenolol, respectively. For all investigated molecules, two well‐defined ranges of linearity Ip vs analyte concentration have been identified which correspond to specific calibration parameters. Calibration graphs (Ip vs concentration) considered in the first interval of linearity, shown correlation coefficients >0.99. A solid phase extraction (SPE) procedure using a polymeric mixed‐mode cationic sorbent (Strata‐X‐C), was studied and optimized. The proposed DPV‐SPE method was successfully applied for the determination of propranolol in several pharmaceutical formulations and urine sample, with results in close agreement with those obtained using traditional liquid chromatography technique coupled with spectrophotometric detection.     

Voltammetric Reduction of a 4‐Nitroimidazole Derivative on a Multiwalled Carbon Nanotubes Modified Glassy Carbon Electrode

We report the electrochemical behavior of a 4‐nitroimidazole derivative, 1‐methyl‐4‐nitro‐2‐hydroxymethylimidazole (4‐NImMeOH), on glassy carbon electrode (GCE) modified with multiwalled carbon nanotubes (MWCNT). As dispersing agents, dimethylformamide (DMF) and water were used. The electrochemical response of the resulting electrodes was evaluated using linear sweep, cyclic and square‐wave voltammetry (LSV, CV and SWV). Several parameters such as medium pH, nature and concentration of the CNTs dispersion and accumulation time were tested. The optimal conditions determined for obtain better response were: pH 2, dispersion concentration=4 mg/mL of CNT in water, accumulation time=7 min. The MWCNT‐modified GCE exhibited attractive electrochemical properties producing enhanced currents with a significant reduction in the overpotential and good signal‐to‐noise characteristics, in comparison with the bare GCE. The modified electrode is highly repeatable for consecutive measurements, reaching a variation coefficient of 2.9% for ten consecutive runs.     

Determination of Quercetin and Luteolin in Paprika Samples by Voltammetry and Partial Least Squares Calibration

Quercetin and luteolin are flavonoids with beneficious properties, which are present in paprika. In this work, both have been determined in paprika by using electrochemistry combined with chemometrics. The electrochemical oxidation mechanisms of both analytes have been studied through sampled direct current (DC) voltammetry, differential pulse voltammetry (DPV) and Square Wave Voltammetry (SWV), making use of a glassy carbon electrode. The final technique selected for the quantification was DPV due to its high repeatability with respect SWV. The chemical variables and the instrumental parameters were optimized and the final conditions employed were ethanol: water (20 : 80), 0.75 mol dm⁻³ of HCl, and a pulse amplitude of 50 mV. Due to the facts that oxidation potential of both analytes were quite similar, their DPV peaks were overlapped, and also because the analytes interaction during the electrochemical process causes a non‐additivity of the signals, they could not be quantified separately by direct measurement of peak intensity. For this reason, a chemometric algorithm was applied (partial least squares (PLS) regression in its modality PLS‐2). In the case of validation samples, appropriate sets of calibration and validation were built and good results were obtained. This methodology was applied to real paprika samples and the results were similar to those obtained with a HPLC method previously reported.     

Study of a Catalytic Mechanism in Additive Differential Pulse Techniques

The new electrochemical double pulse technique, known as additive differential normal pulse voltammetry (ADNPV) when there is no restriction on the duration of both pulses, and additive differential pulse voltammetry (ADPV) when t₂?t₁, has been applied to a pseudo‐first‐order catalytic mechanism. The expressions obtained here are applicable to planar and spherical electrodes, of any radius. This is of great interest since the size of the electrode plays an important role in the preponderating of diffusive and kinetics processes. The signal obtained with this technique presents the same morphological characteristics as the triple pulse technique, double differential pulse voltammetry (DDPV) and is more advantageous than DDPV and than the double pulse one, differential pulse voltammetry (DPV).     

Voltammetric Determination of Pb(II) and Cd(II) Ions in Well Water Using a Sputtered Bismuth Screen‐Printed Electrode

A method using commercially available sputtered bismuth screen‐printed electrodes (Bi_spSPE), as substitute to mercury electrodes, for the determination of trace Pb(II) and Cd(II) ions in drinking well water samples collected in a contaminated area in The Republic of El Salvador by means of differential pulse anodic stripping voltammetry (DPASV) has been proposed. The comparable detection and quantification limits obtained for both Bi_spSPE and hanging mercury drop electrode (HMDE), together with the similar results with a high reproducibility obtained in these water samples analyses recommend the applicability of Bi_spSPE for the determination of low level of metal concentrations in natural samples.     

Mercury meniscus on solid silver amalgam electrode as a sensitive electrochemical sensor for tetrachlorvinphos

The in-house prepared mercury meniscus modified solid silver amalgam electrode (m-AgSAE) was successfully applied for the detection of organophosphate pesticide tetrachlorvinphos in pH 7 buffer solution. The electrochemical performance of m-AgSAE for the reduction of tetrachlorvinphos was evaluated using cyclic voltammetry (CV), differential pulse voltammetry (DPV), and square wave voltammetry (SWV), respectively. The surface morphology of solid silver electrode (AgE), as-amalgamated solid silver amalgam electrode (AgSAE), and polished solid silver amalgam electrode (p-AgSAE) was examined by field emission scanning electron microscopy (FESEM). Among the applied techniques, DPV and SWV analysis showed a remarkable increase in the reduction peak current and provided a simple, fast, and sensitive method for the determination of tetrachlorvinphos. The electrochemical impedance spectroscopy (EIS) was used to correlate the electrocatalytic activity of AgSAE, p-AgSAE and m-AgSAE with their interfacial charge transport capabilities. Under the optimized experimental conditions, the DPV and SWV responses were linear over the 1–9 μM and 10–50 μM concentration ranges with a detection limit of 0.06 μM for DPV and 0.04 for SWV. The estimation of tetrachlorvinphos in the ground and waste water samples with the proposed method was in good agreement with that of the added amount. The proposed electrochemical method not only extends the application of non-toxic m-AgSAE, but also offers new possibilities for fast and sensitive analysis of tetrachlorvinphos and its structural analogs in environmental samples.     

A Novel Electrochemical Sensor Based on Poly(1,5-diaminonaphthalene) and Poly(1,2-diaminoanthraquinone) Core-shell Composite Electrodes for Effective Voltammetric Determination of Nitrite

In this article, poly(1,2-diaminoanthraquinone) (pDAAQ) and poly(1,5-diaminonaphthalene) (pDAN) were electrochemically deposited layer by layer on a glassy carbon electrode (GCE) to generate pDAAQ/pDAN@GCE and pDAN/pDAAQ@GCE composite electrodes, respectively. The morphology and characteristics of the modified electrodes were investigated via electrochemical impedance spectroscopy)EIS), Fourier transform infrared spectroscopy (FT-IR), and scanning electron microscopy)SEM). The obtained results reveal the outstanding performance of the pDAN/pDAAQ@GCE electrode for electrochemical nitrite sensing where pDAAQ plays a vital role as the inner layer. Cyclic voltammetry (CV), linear sweep voltammetry (LSV), and differential pulse voltammetry (DPV) measurements revealed that the oxidation peak current of nitrite was proportional to its concentration. The best LSV results were obtained in a concentration range of 10–150 μM, with a limit of detection of 1.2 μM. Furthermore, the pDAN/pDAAQ@GCE composite electrode was used to determine nitrite ions in real water samples with good results.     

Determination of Azidothymidine – an Antiproliferative and Virostatic Drug by Square‐Wave Voltammetry

The 3′‐azido‐3′‐deoxythymidine (AZT, Zidovudine) is an antiproliferative and virostatic drug widely used in human immunodeficiency virus type 1 (HIV‐1) infection treatment. With respect to side effects of high doses and a short half‐life of AZT, a fast and simple detection method for this agent could be helpful. The aim of our study was to determine AZT levels in natural samples (urine, serum, whole blood, and cell cultures, such as the HaCaT line of keratinocytes) without their mineralization and/or purification, by means of electrochemical methods using hanging mercury drop electrode (HMDE). On this electrode, AZT undergoes irreversible reduction at the peak potential near E_p?1.1 V (vs. Ag/AgCl/3 M KCl). Reduction AZT signals were measured by cyclic voltammetry (CV), differential pulse voltammetry (DPV), square‐wave voltammetry (SWV), and constant current chronopotentiometric stripping analysis (CPSA). In phosphate buffer (pH 8) the SWV yielded the best AZT signal with the detection limit of 1 nM. The determination of AZT concentration in biological materials is affected by electroactive components, such as proteins and DNA. For monitoring the influence of these compounds, AZT reduction was performed in the presence of 10 μg/mL calf thymus ssDNA and/or 100 μg/mL bovine serum albumin. In these cases, the detection limit increased to 0.25 μM. Also studied was the AZT concentration in keratinocyte cells (HaCaT line) during cell cultivation. It has been shown that the SWV may be considered as a useful tool for the determination of AZT concentration in cell cultures, and for monitoring AZT pharmacokinetics.     

Voltammetric Determination of Bisphenol A in Water and Juice Using a Lanthanum (III)-Doped Cobalt (II,III) Nanocube Modified Carbon Screen-Printed Electrode

A La³⁺ doped Co₃O₄ nanocube modified graphite screen-printed electrode (La³⁺-doped Co₃O₄ nanocube/SPE) was prepared and utilized for the sensitive voltammetric determination of bisphenol A. In comparison with an unmodified electrode, the presence of the La³⁺ doped Co₃O₄ nanocubes caused a significant enhancement in the peak current. Differential pulse voltammetry (DPV), cyclic voltammetry (CV), and chronoamperometry approaches were utilized as diagnostic methods. The modified SPE was used to determine bisphenol A concentrations in the range from 0.5 to 900.0?μM with a limit of detection equal to 6.1?×?10^?8 M. Real samples were effectively analyzed with the modified electrode.     

Quantitative Analysis of Irbesartan in Pharmaceuticals and Human Biological Fluids by Voltammetry

Abstract

A differential pulse (DP) and square wave (SW) voltammetric techniques were developed for the determination of irbesartan. The electrochemical behavior of irbesartan was investigated by cyclic voltammetry (CV), differential pulse voltammetry (DPV), and square wave voltammetry (SWV) at the hanging mercury drop electrode (HMDE). Different parameters were tested to optimize the conditions of the determination. It was found that in the range of 8 × 10^?6–1 × 10^?4 M, the currents measured by both of methods presented a good linear property as a function of the concentration of irbesartan. In addition, validation parameters, such as reproducibility, sensitivity, and recovery were evaluated as well. The slope of the log Ip- log ν linear plot was 0.58 indicating the diffusion control for 0.5 M sulphuric acid without the need for separation or complex sample preparation, since there was no interference from the excipients and endogenous substances.

The methods were successfully applied to the analysis of irbesartan in the pharmaceutical tablet formulations and in human serum samples.     

Voltammetric Determination of α‐Tocopheryl Acetate in Pharmaceutical Dosage Forms

A simple and rapid voltammetric method has been developed for the quantitative determination of α‐tocopheryl acetate (α‐TOAc) in pharmaceutical preparations. Studies with linear scan (LSV), square‐wave (SQWV) and differential pulse voltammetry (DPV) were carried out using platinum microelectrodes. A well‐defined, irreversible oxidation wave/peak was obtained at 1.30 V (vs. Ag/AgCl reference electrode.) The use of SQWV or DPV technique provides a precise determination of α‐tocopheryl acetate using the multiple standard addition method. The statistical parameters and the recovery study data clearly indicate good reproducibility and accuracy of the method. Accuracy of the results assessed by recovery trials was found within the 99.3% to 103.5%, and 99.1% to 101.4%, for SQWV and DPV, respectively. The quantification limits for the both voltammetric techniques were found to be 6×10^?5 M (SQWV) and 7×10^?5 M (DPV). Analysis of the authentic samples containing α‐TOAc showed no interference with common additives and excipients, such as unsaturated fatty acids (co‐formulated as glycerine esters) and vitamin A (as retinol or β‐carotene). The method proposed does not require any pretreatment of the pharmaceutical dosage forms. A gas chromatography determination of α‐TOAc in real samples was also performed for comparison.     

Electrochemical and Spectroscopic Study of the Interaction of Indirubin with DNA

The interaction of indirubin with DNA was studied by differential pulse voltammetry (DPV) and linear sweep voltammetry (LSV) at the bare or DNA‐modified electrode and UV‐vis or IR spectra. As a result of intercalating of this drug into the double helical structure of DNA, the DPV of indirubin shows that peak potentials shift and peak currents decrease with the addition of DNA. UV‐vis spectra exhibits that the absorption intensity of indirubin at 538.7 nm^?1 decreases, which indicates that the anticancer herbal drug indirubin binds DNA. In addition, IR‐spectra of DNA and DNA‐indirubin adduct imply indirubin interacts with the phosphate groups of DNA by hydrogen bond or electrostatic interaction. Under our experiment conditions, the decrease of peak current is proportional to DNA concentration, which can be applied to estimate DNA concentration. The results indicate that the herbal drug indirubin can interfere with the DNA by intercalating into the double helix of DNA and interacting with the phosphate groups of DNA.     

Investigation of electrochemical behavior of lipid lowering agent atorvastatin calcium in aqueous media and its determination from pharmaceutical dosage forms and biological fluids using boron-doped diamond and glassy carbon electrodes

The electrochemical behavior of atorvastatin calcium at glassy carbon and boron-doped diamond electrodes has been studied using voltammetric techniques. The possible mechanism of oxidation was discussed with model compounds. The dependence of the peak current and potentials on pH, concentration, scan rate and nature of the buffer were investigated for both electrodes. The oxidation of atorvastatin was irreversible and exhibited a diffusion-controlled fashion on the diamond electrode. A linear response was obtained within the range of 9.65 x 10(-7) - 3.86 x 10(-5) M in 0.1 M H(2)SO(4) solution for both electrodes. The detection limits of a standard solution are estimated to be 2.11 x 10(-7) M with differential pulse voltammetry (DPV) and 2.05 x 10(-7)M with square wave voltammetry (SWV) for glassy carbon electrode, and 2.27 x 10(-7) M with DPV and 1.31 x 10(-7)M with SWV for diamond electrodes in 0.1 M H(2)SO(4) solution. The repeatability of the methods was found good for both electrodes. The methods were fully validated and successfully applied to the high-throughput determination of the drug in tablets, human serum and human urine with good recoveries.     

Voltammetric Determination of Neonicotinoid Pesticides at Disposable Screen‐Printed Sensors Featuring a Sputtered Bismuth Electrode

This work reports the determination of 5 neonicotinoid pesticides (Clothianidin, Imidacloprid, Thiamethoxam, Nitenpyram and Dinotefuran) in water samples by cathodic differential pulse (DP) voltammetry at screen‐printed disposable sensors featuring a sputtered bismuth thick‐film working electrode, a Ag reference electrode and a carbon counter electrode. The performance of the bismuth thick‐film electrodes was compared to that of a home‐made bismuth thin‐film electrode and a bismuth‐bulk electrode. The electrodes were further characterized by electrochemical and optical techniques. The effect of the pH of the supporting electrolyte on the DP reduction currents of the 5 pesticides was studied. The limits of quantification (LOQs) in 4 water matrices (distilled water, tap water, mineral water and surface water) were in the range 0.76 to 2.10 mg L^?1 but severe matrix effects were observed in the analysis of mineral and, especially, surface water samples. Using a solid‐phase extraction (SPE) procedure using Lichrolut EN cartridges and elution with methanol, the matrix effects were substantially reduced and the LOQs were in the range 9 to 17 µg L^?1_. The recoveries of surface water samples spiked with the 5 target neonicotinoids at two concentration levels (20 and 50 µg L^?1) were in the range 89 to 109 % and the % relative standard deviations ranged from 4.3 to 7.2 %.     

Electrocatalytic Determination of Nitrite on a Rigid Disk Electrode Having Cobalt Phthalocyanine Prepared In Situ

This work reports an in situ cobalt(II) phthalocyanine (CoPc) synthesis on a SiO₂/SnO₂ (SiSn) matrix surface obtained by the sol‐gel method and its electrocatalytic activity for oxidation of nitrite. A rigid disk electrode with SiSn/CoPc was used to study the electrooxidation of nitrite by the cyclic voltammetric, chronoamperometric techniques and differential pulse voltammetry (DPV). The adsorbed phthalocyanine electrocatalyzed nitrite oxidation at 0.73 V (versus SCE) using the DPV technique. The anodic peak current intensities, plotted from differential pulse voltammograms in 1 mol L^?1 KCl for the concentration range 0.002 to 3.85 mmol L^?1 of nitrite were linear, with a correlation coefficient of 0.998 and a detection limit of 0.95 μmol L^?1.     

Characterization of an electrochemical mercury sensor using alternating current,cyclic, square wave and differential pulse voltammetry

Here we report the characterization of an electrochemical mercury (Hg²⁺) sensor constructed with a methylene blue (MB)-modified and thymine-containing linear DNA probe. Similar to the linear probe electrochemical DNA sensor, the resultant sensor behaved as a “signal-off” sensor in alternating current voltammetry and cyclic voltammetry. However, depending on the applied frequency or pulse width, the sensor can behave as either a “signal-off” or “signal-on” sensor in square wave voltammetry (SWV) and differential pulse voltammetry (DPV). In SWV, the sensor showed “signal-on” behavior at low frequencies and “signal-off” behavior at high frequencies. In DPV, the sensor showed “signal-off” behavior at short pulse widths and “signal-on” behavior at long pulse widths. Independent of the sensor interrogation technique, the limit of detection was found to be 10 nM, with a linear dynamic range between 10 nM and 500 nM. In addition, the sensor responded to Hg²⁺ rather rapidly; majority of the signal change occurred in <20 min. Overall, the sensor retains all the characteristics of this class of sensors; it is reagentless, reusable, sensitive, specific and selective. This study also highlights the feasibility of using a MB-modified probe for real-time sensing of Hg²⁺, which has not been previously reported. More importantly, the observed “switching” behavior in SWV and DPV is potentially generalizable and should be applicable to most sensors in this class of dynamics-based electrochemical biosensors.     

DPV and SWV Determination of Estrone Using a Cathodically Pretreated Boron‐Doped Diamond Electrode

Voltammetric methods for estrone determination were developed using a cathodically pretreated BDD electrode with DPV or SWV. Analytical curves were obtained for estrone concentrations from 0.20 or 0.10 to 2.0 µmol L^?1, for DPV or SWV, with detection limits of 0.20 and 0.10 µmol L^?1, respectively. The SWV method was successfully applied in estrone recovery studies in different water matrices. Additionally, these recovery results were reasonably similar to those attained using HPLC/UV‐vis. Comparatively to other electroanalytical methods based on different carbon electrodes, the here‐reported novel methods yield very good results, being adequate for estrone determination in environmental samples.