Amperometric Detection of Catecholamine Neurotransmitters Using Electrocatalytic Substrate Recycling at a Laccase Electrode

An enzyme electrode based on the coimmobilization of an osmium redox polymer and laccase on glassy carbon electrodes has been applied to ultra sensitive amperometric detection of the catecholamine neurotransmitters dopamine, epinephrine and norepinephrine, resulting in nanomolar detection limits, as low as 4 nM for dopamine. The sensitivity of the electrode is due to signal amplification via oxidation of the catecholamine by the immobilized laccase, which is regenerated by concomitant reduction of oxygen to water, coupled to the electrocatalytic re‐reduction of the oxidized catecholamine by the osmium redox complex: electrocatalytic substrate recycling. In addition because the sensor can be operated in reductive mode at ?0.2 V (vs. Ag/AgCl), noise and interferences are diminished. Combined with its high sensitivity this enzyme electrode also exhibited excellent selectivity allowing the detection of catecholamines in the presence of ascorbic acid. However, differentiation between the current responses achieved for the three catecholamines is not possible. The effective mode of constant recycling, resulting in amplification of the current response, of the laccase enzyme electrode sensor combined with the inherent advantages of using electrochemical techniques holds great promise for the future of catecholamine detection and monitoring.     

Simultaneous determination of ascorbic acid, uric acid and neurotransmitters with a carbon ceramic electrode prepared by sol-gel technique

A sol-gel carbon composite electrode (CCE) has been prepared by mixing a sol-gel precursor (e.g. methyltrimethoxysilane) and carbon powder without adding any electron transfer mediator or specific reagents. It was demonstrated that this sensor can be used for simultaneous determination ascorbic acid, neurotransmitters (dopamine and adrenaline) and uric acid. Direct electrochemical oxidation of ascorbic acid, uric acid and catecholamines at a carbon composite electrode was investigated. The experimental results were compared with other common carbon based electrodes, specifically, boron doped diamond, glassy carbon, graphite and carbon paste electrodes. It was found that the CCE shows a significantly higher of reversibility for dopamine. In addition, in comparison to the other electrodes used, for CCE the oxidation peaks of uric acid, ascorbic acid and catecholamines in cyclic and square wave voltammetry were well resolved at the low positive potential with good sensitivity. The advantages of this sensor were high sensitivity, inherent stability and simplicity and ability for simultaneous determination of uric acid, catecholamines and ascorbic acid without using any chromatography or separation systems. The analytical performance of this sensor has been evaluated for detection of biological molecules in urine and serum as real samples.     

A novel non-enzymatic glucose sensor based on Cu nanoparticle modified graphene sheets electrode

A novel, stable and sensitive non-enzymatic glucose sensor was developed by potentiostatically electrodepositing metallic Cu nanoparticles on graphene sheets. The electrochemical performance of the Cu-graphene sheets electrode for detection of glucose was investigated by cyclic voltammetry and chronamperometry. The Cu-graphene sheets electrode displayed a synergistic effect of copper nanoparticles and graphene sheets towards the oxidation of glucose in alkaline solution, showing higher oxidation current and negative shift in peak potential. At detection potential of 500 mV, the Cu-graphene electrode sensor presented a wide linear range up to 4.5 mM glucose with a detection limit of 0.5 μM (signal/noise = 3). In addition, the sensor responds very quickly (<2 s) with addition of glucose. Furthermore, the Cu-graphene sheets electrode exhibits high stability and selectivity to glucose, and the poisoning by chloride ion as well as interference from the oxidation of common interfering species (ascorbic, dopamine, uric acid and carbohydrate) are effectively avoided. The Cu-graphene sheets electrode allows highly selective and sensitive, stable and fast amperometric sensing of glucose, which is promising for the development of non-enzymatic glucose sensor.     

Gold-dendrimer Nanocomposite Based Electrochemical Sensor for Dopamine

An electrochemical sensor for dopamine was developed by electrodepositing poly(propylene imine) (PPI) dendrimer and gold nanoparticles (AuNPs) onto a glassy carbon electrode (GCE). Electrochemical characterisation of the sensor was carried out by cyclic voltammetry and electrochemical impedance spectroscopy in ferri/ferrocyanide electrolyte. The nanocomposite electrode (GCE-PPI-AuNPs) showed improved electroactive surface area and electrochemical response over bare GCE. The sensor recorded a detection limit of 0.16 μM over a concentration range of 0.1 μM to 125 μM. The sensor was applied for dopamine detection in human serum samples and in the presence of interfering substances such as ascorbic acid and epinephrine.     

Enhanced Electrocatalytic Activity of Ni‐CNT Nanocomposites for Simultaneous Determination of Epinephrine and Dopamine

A promising electrochemical sensor based nickel‐carbon nanotube (Ni‐CNT) modified on glassy carbon (GC) electrode had been developed and the properties of the modified electrode were characterized by multispectroscopic analysis. The fabricated sensor (GC/Ni‐CNT) electrode was utilized to determine the catecholamines such as epinephrine and dopamine simultaneously. Differential pulse voltammetry and amperometry were used to verify the electrochemical behavior of the studied compounds. The GC/Ni‐CNT based amperometric sensor showed a wide linear range and low detection limit with high analytical sensitivity of 8.31 and 6.61 μA μM^?1 for EP and DA, respectively which demonstrates better characteristics compared to other electrodes reported in the literature. Further, no significant change in amperometric current response was observed in presence of biological interference species such as glucose, cysteine, citric acid, uric acid and ascorbic acid in the detection of EP and DA. The utility of this GC/Ni‐CNT electrode was well established for the determination of EP and DA in human urine samples.     

Label-free photoelectric sensor for lactic acid determination in human sweat

A label-free lactic acid sensor has been successfully developed by using a Dysprosium single crystal-based photoelectric potential technique via Dy-SCN/FTO electrode. Interestingly, the proposed sensor demonstrated excellent performance for l-lactic acid analysis with a wide linear range of 0.0196～16.31 mmol/L, the detection limit of as low as 3.20 µmol/L as well as an advisable stability. The feasibility of this strategy was also verified by practical application towards human sweat samples. The mechanism studies indicated that lactic acid molecules specifically bind to the surface of semiconductor materials, which alters the charge distribution of the electrode surface and subsequently results in band bending/photoelectric potential changes. The theoretical formula for this photoelectric chemistry (PEC) strategy was then derived according to charge balance theory. We believe that the proposed Dy-SCN/FTO sensor would open a new way for rapid, non-invasive l-lactic acid level evaluation during human physical condition monitoring.     

Electroanalysis of Dopamine at RuO2 Modified Vertically Aligned Carbon Nanotube Electrode

Electrochemical behavior of dopamine at the RuO₂‐modified vertically aligned carbon nanotubes electrode was investigated by cyclic voltammetry, differential pulse voltammetry and chronoamperometry. The RuO₂‐modified carbon nanotube electrode showed higher electrocatalytic activity towards the oxidation of dopamine than the MWNTs electrode in 0.10 M phosphate buffer solution. At an applied potential of +0.4 V, the RuO₂/MWNTs electrode exhibited a wide detection range up to 3.6×10^?3 M with detection limit of 6.0×10^?8 M (signal/noise=3) for dopamine determination. Meanwhile, the optimized sensor for dopamine displayed a sensitivity of 83.8 μA mM^?1 and response time of 5 s with addition of 0.20 mM dopamine. In addition, DPV experiment revealed that interfering species such as ascorbic acid and uric acid could be effectively avoided. The RuO₂/MWNTs electrode presents stable, highly sensitive, favorable selectivity and fast amperometric response of dopamine.     

Nonenzymatic glucose sensor based on CuO microfibers composed of CuO nanoparticles

Fluorine tin oxide (FTO) electrode modified by copper oxide microfibers (CuO-MFs) composed of numerous interconnected CuO nanoparticles (CuO-NPs) for nonenzymatic glucose sensor was prepared by electrospinning precursor containing high percentage content of copper nitrate with subsequent calcination. The results of scanning electron microscope (SEM) showed the size of CuO particles composing CuO-MFs depended on the percentage content of copper nitrate in precursor solution. With increasing the percentage content of copper nitrate, the interconnected CuO-NPs would gradually replace the large-size CuO particles to accumulate the CuO-MFs, which have the potential to provide larger surface area and more reaction sites for electrocatalytic activity toward glucose. As a glucose sensor, the CuO-MFs modified FTO electrode prepared by 40 wt.% of copper nitrate exhibited a high sensitivity of 2321 μA mM⁻¹ cm⁻² with a low detection limit of 2.2 nM (signal/noise ratio (S/N) = 3). Additionally, the application of the CuO-MFs modified FTO electrode as a glucose sensor for biological samples was demonstrated with satisfactory results.     

Disposable amperometric sensor for neurotransmitters based on screen-printed electrodes modified with a thin iridium oxide film.

Potential cycling in the range from -0.2 to +1.2 V is used for the electrodeposition of hydrous iridium oxide films onto a screen-printed electrode from a saturated solution of alkaline iridium(III) solution. The iridium oxide redox couple shows a stable and obvious reversible redox, with the formal potential being pH dependent in the range 1-14. The properties, stability and electrochemical properties of iridium oxide films were investigated by cyclic voltammetry. A modified electrode showed excellent catalytic activity toward the oxidation of neurotransmitters (catecholamines) over a wide pH range (2-8). The electrocatalytic behavior is further exploited as a sensitive detection scheme for adrenaline and dopamine by hydrodynamic amperometry. Under the optimized conditions, the calibration curves are linear in the concentration range 0.1-70 and 0.1-15 microM for dopamine and adrenaline determination, respectively. The detection limit and sensitivity are 30 nM and 30 nA/microM for adrenaline and 15 nM and 80 nA/microM for dopamine. Finally, the analytical performance of the modified electrode was demonstrated for the elimination of interference by uric acid in catecholamines determination when present in a 1000-fold concentration excess.     

Single step modification of copper electrode for the highly sensitive and selective non-enzymatic determination of glucose

A non-enzymatic sensor was developed for the determination of glucose in alkaline medium by anodisation of copper in sodium potassium tartrate solution. The morphology of the modified copper electrode was studied by scanning electron microscopy, and its electrochemical behavior by cyclic voltammetry and electrochemical impedance spectroscopy. The electrode enables direct electrocatalytic oxidation of glucose on a CuO/Cu electrode at 0.7 V in 0.1 M sodium hydroxide. At this potential, the sensor is highly selective to glucose even in the presence of ascorbic acid, uric acid, or dopamine which are common interfering species. The sensor displays a sensitivity of 761.9 μA mM^?1 cm^?2, a linear detection range from 2 μM to 20 mM, a response time of <1 s, and a detection limit of 1 μM (S/N = 3). It was tested for determination of glucose level in blood serum.     

β-Sonogel-Carbon electrodes: A new alternative for the electrochemical determination of catecholamines

In this work, a new alternative for the electrochemical determination of catecholamines based on β-cyclodextrin-Sonogel-Carbon electrodes is reported. The incorporation of β-CD and graphite in the preparation of the Sonogel-Carbon material leads to a modification of the electrode surface properties which causes a significant increase in the oxidation peak current of biomolecules such as dopamine, l-epinephrine, d,l-norepinephrine and catechol. This phenomenon might be attributed to the formation of an inclusion complex between β-CD and the catecholamines. The amount of β-CD necessary to form the Sonogel electrode was studied and optimization of electrochemical parameters, perm selectivity and mechanical stability of the sensor are discussed. Scanning electron microscopy and electrochemical impedance spectroscopy measurements were employed to characterize the electrical parameters and the structural properties of the new electrode surface, respectively. Cyclic voltammetry (CV) and Adsorptive differential pulse voltammetry (AdDPV) measurements were also used to explore the electrochemical behaviour of the electrode versus the quoted catecholamines. The β-CD-Sonogel-Carbon electrode offers fast and linear responses towards dopamine, norepinephrine, epinephrine and catechol, with good and low detection limits: 0.164, 0.294, 0.699 and 0.059 μmol L⁻¹, respectively.     

镍钴双金属-卟啉有机框架复合纳米材料构建的无酶传感器检测多巴胺

以Ni、Co为金属节点,5,10,15,20-四（4-羧基苯基）卟啉（TCPP）为金属配体,合成了金属有机框架材料（MOFs）作催化材料,以还原氧化石墨烯（rGO）和乙炔黑（ACET）作信号放大材料,制备出一种灵敏度高、稳定性高、选择性好的无酶电化学传感器,用于检测多巴胺（DA）。通过一步水热法制成rGO-NiCoTCPP,再用滴涂法将其修饰在玻碳电极上,即得GCE/rGO-NiCoTCPP电极,最后将ACET滴涂在此电极上,得到GCE/rGO-NiCoTCPP/ACET电极。利用红外光谱、扫描电子显微镜和电化学阻抗对此电极进行了表征,并将不同修饰电极放在磷酸缓冲液中进行循环伏安表征。GCE/rGO-NiCoTCPP/ACET传感器对DA具有较宽线性范围（0.4 ~160 μmol/L）及较高的电流响应（检出限为0.198 μmol/L）,有望应用于实际样品中DA的检测。     

A sensitive determination of dopamine in the presence of ascorbic acid using a nafion-coated clinoptilolite-modified carbon paste electrode

A selective dopamine determination using a nafion-coated clinoptilolite-modified carbon paste electrode in the presence of ascorbic acid was studied. Both cyclic voltammetry (CV) and differential pulse anodic stripping voltammetry (DPASV) were used for measurements of dopamine. To improve the selectivity of the clinoptilolite-modified carbon paste electrode in presence of a high concentration of ascorbic acid, the electrode surface was coated with nafion membrane. Experimental parameters affecting the determination of dopamine, including the clinoptilolite ratio, nafion membrane thickness, preconcentration time, preconcentration solution pH, stripping solution pH and interferences are discussed. The developed sensor has a wide linear range, a low detection limit, and good stability and reproducibility. The sensor offers a good alternative to existing analytical methods for dopamine, permits a relatively short analysis time, and is simple, selective and inexpensive.     

Keggin 型磷钨酸盐修饰碳糊电极传感多巴胺的研究

多金属氧酸盐作为一类阴离子簇合物,由于其结构的多样性和尺寸大小的可调变性,在电化学、催化和药学等领域引起了人们的广泛关注.本文制备了多酸Co(C₁₅N₆H₁₂)₂[PW₁₂O₃₈]·5H₂O（Co[PW₁₂O₃₈]）修饰碳糊电极并通过电化学阻抗谱、循环伏安法以及差分脉冲伏安法对多巴胺的传感性能进行了研究.对其制备条件和检测条件分别进行了优化.在优化条件下,制备的传感器对多巴胺具有良好的选择性和灵敏度的检测能力.多巴胺的线性响应范围为8.0x10^-6 mol·L^-1至3x10^-5 mol·L^-1,灵敏度为0.039 μA·(μmol·L^-1)^-1,检出限（S/N=3）为5.4 x10^-6 mol·L^-1. 制备的多酸修饰碳糊电极用于检测多巴胺表现出良好的稳定性和重现性,并且对抗坏血酸、尿酸等常见的干扰物质,具有良好的抗干扰性. 多酸修饰的碳糊电极制备过程简单方便,成本低,传感性能良好,对应用于电化学传感器检测多巴胺具备潜在的应用前景.      

Third Generation ATP Sensor with Enzymatic Analyte Recycling

For the first time the direct electron transfer of an enzyme ‐ cellobiose dehydrogenase, CDH ‐ has been coupled with the hexokinase catalyzed competition for glucose in a sensor for ATP. To enhance the signal output for ATP, pyruvate kinase was coimmobilized to recycle ADP by the phosphoenolpyruvate driven reaction. The new sensor overcomes the limit of 1 : 1 stoichiometry of the sequential or competitive conversion of ATP by effective enzymatic recycling of the analyte. The anodic oxidation of the glucose converting CDH proceeds at electrode potentials below 0 mV vs. Ag|AgCl thus potentially interfering substances like ascorbic acid or catecholamines do not influence the measuring signal. The combination of direct electron transfer of CDH with the enzymatic recycling results in an interference‐free and oxygen‐independent measurement of ATP in the lower µmolar concentration range with a lower limit of detection of 63.3 nM (S/N=3).     

Voltammetric Detection of Catechol and Dopamine Based on a Supramolecular Composite Prepared from Multifarene[3,3] and Reduced Graphene Oxide

A selective and sensitive modified‐electrode for catechol and dopamine was presented with supramolecular recognition accomplished by making use of the macrocyclic host multifarene[3,3] that was used as a composite with reduced graphene oxide. The morphologies and electrochemical nature of the composite were characterized by atomic force microscopy, transmission electron microscopy, cyclic voltammetry and differential pulse anodic voltammetry. The modified electrode, best operated at a potential around 0.16 V vs. Ag/AgCl, displayed a differential pulse voltammetric response in the linear concentration range of 10–100 nM within a detection limit of 0.51 nM (at S/N=3). It was further applied to detect dopamine (at a working potential of 0.18 V vs. Ag/AgCl) in the linear concentration range of 10–100 nM with a detection limit of 0.62 nM. The modified electrode also exhibited satisfactory results to the determination of dopamine injections. The constructed modified electrode for dopamine detection was investigated in the presence of the interfering substances including glucose, urea and ascorbic acid, indicating a good selectivity.     

Amperometric Detection of Catechol and Catecholamines by Immobilized Laccase from DeniLite

DeniLite laccase immobilized Pt electrode was used for detection of catechol and catecholamines. The enzymatically oxidized substrates were measured amperometrically. The sensitivities are 210, 75, 60 and 45 nA/μM with the upper limits of linear ranges of 58, 40, 55 and 55 μM and the detection limits (S/N=3) of 0.07, 0.2, 0.3 and 0.4 μM for catechol, dopamine (DA), norepinephrine (NEPI) and epinephrine (EPI), respectively. The response time (t_90%) is about 2 seconds for each substrate and the long‐term stability is around 40–50 days with retaining 80% of initial activity. The very fast response and the remarkable long‐term stability are the principal advantages of this sensor. In case of catechol, the pH response of the sensor is mainly determined by enzyme's pH profile, however, in case of catecholamines, both enzyme's pH profile and reversibility of the substrate are operated and the optimal pHs for NEPI and EPI shift towards acidic range compared to that for DA. The presence of ascorbic acid (<50 μM) did not interfere with the measurement.     

Simple method for the simultaneous determination of acetylcholine, choline, noradrenaline, dopamine and serotonin in brain tissue by high-performance liquid chromatography with electrochemical detection

A simple method for the simultaneous determination of acetylcholine, choline, noradrenaline, dopamine and serotonin in brain tissue was developed by using high-performance liquid chromatography with electrochemical detection. These compounds are analysed in a single chromatographic run within 30 min with a simple sample clean-up procedure. The detection system consists of two electrochemical detector cells aligned in series: a glassy-carbon electrode for catecholamines and serotonin, and a platinum electrode for acetylcholine and choline. For the detection of the latter compounds, they were converted enzymatically into hydrogen peroxide through a column reactor with immobilized acetylcholinesterase and choline oxidase. A column of boronic acid gel was placed just ahead of the immobilized enzyme column to remove catecholamines, which caused interfering responses on the platinum electrode. Two equivalent analytical columns and a column switching were employed to speed up the serotonin assay. Simultaneous determination of these major neurotransmitters in rat brain regions was successfully carried out with the system described.     

Sensitive determination of dopamine in the presence of uric acid and ascorbic acid using TiO2 nanotubes modified with Pd, Pt and Au nanoparticles

A simple modified TiO(2) nanotubes electrode was fabricated by electrodeposition of Pd, Pt and Au nanoparticles. The TiO(2) nanotubes electrode was prepared using the anodizing method, followed by modifying Pd nanoparticles onto the tubes surface, offering a uniform conductive surface for electrodeposition of Pt and Au. The performance of the modified electrode was characterized by cyclic voltammetry and differential pulse voltammetry methods. The Au/Pt/Pd/TiO(2) NTs modified electrode represented a high sensitivity towards individual detection of dopamine as well as simultaneous detection of dopamine and uric acid using 0.1 M phosphate buffer solution (pH 7.00) as the base solution. In both case, electro-oxidation peak currents of dopamine were linearly related to accumulated concentration over a wide concentration range of 5.0 × 10(-8) to 3.0 × 10(-5) M. However in the same range of dopamine concentration, the sensitivity had a significant loss at Pt/Pd/TiO(2) NTs electrode, suggesting the necessity for Au nanoparticles in modified electrode. The limit of the detection was determined as 3 × 10(-8) M for dopamine at signal-to-noise ratio equal to 3. Furthermore, the Au/Pt/Pd/TiO(2) NTs modified electrode was able to distinguish the oxidation response of dopamine, uric acid and ascorbic acid in mixture solution of different acidity. It was shown that the modified electrode possessed a very good reproducibility and long-term stability. The method was also successfully applied for determination of DA in human urine samples with satisfactory results.     

Facile preparation of a cellulose microfibers–exfoliated graphite composite: a robust sensor for determining dopamine in biological samples

A simple and robust dopamine (DA) sensor was developed using a cellulose microfibers (CMF)–exfoliated graphite composite-modified screen-printed carbon electrode (SPCE) for the first time. The graphite-CMF composite was prepared by sonication of pristine graphite in CMF solution and was characterized by high-resolution scanning electron microscopy, Fourier transform, infrared, and Raman spectroscopy. The cyclic voltammetry results reveal that the graphite-CMF composite modified SPCE has superior electrocatalytic activity against oxidation of dopamine than SPCE modified with pristine graphite and CMF. The presence of large edge plane defects on exfoliated graphite and abundant oxygen functional groups of CMF enhance electrocatalytic activity and decrease potential to oxidize DA. Differential pulse voltammetry was used to quantify DA using the graphite-CMF composite-modified SPCE and demonstrated a linear response for DA detection in the range of 0.06–134.5 µM. The sensor shows a detection limit at 10 nM with an appropriate sensitivity and displays appropriate recovery of DA in human serum samples with good repeatability. Sensor selectivity is demonstrated in the presence of 50-fold concentrations of potentially active interfering compounds including ascorbic acid, uric acid, and dihydroxybenzene isomers.