铜膜差分脉冲阳极溶出伏安法测定药物中铋的含量

研究了铜膜电极代替汞膜电极测定重金属铋的差分脉冲溶出伏安法。实验了同位镀膜法测定铋的条件。在最佳实验条件下,Bi3+浓度在5×10-8~2×10-5mol/L范围内,其溶出峰峰高与浓度呈线性关系,检出限达到1×10-8mol/L。测定了一些药物中铋的含量,结果准确。     

Voltammetric Detection of Captopril Using Copper(II) and an Unmodified Glassy Carbon Electrode

We report a simple, sensitive, and rapid detection of captopril using copper(II) and a bare glassy carbon electrode with cyclic voltammetry. The captopril is detected by the formation of a copper(II)‐captopril complex that is observed to have a characteristic oxidation potential at+0.24 V vs. Ag/AgCl. It is found that the peak current varies linearly with the concentration of captopril. The linear dynamic range is obtained for a captopril concentration of 1 µM to 10 µM, and the sensitivity is found to be 0.10±0.003 μA μM^?1. Importantly, the low limit of detection (n=3) of 0.10 μM and the precision of 3.2 %, are achieved using a simple, unmodified electrode. This is attributable to in situ adsorption of a copper(II)‐captopril complex on the electrode surface.     

Sub‐ppt Level Detection of Mercury(II) Based on Anodic Stripping Voltammetry with Prestripping Step at an In Situ Formed Bismuth Film Modified Glassy Carbon Electrode

Sensitive and selective detection of Hg²⁺ in solution is a challenging work. An anodic stripping voltammetry with prestripping step at an in situ formed bismuth film modified glassy carbon electrode was proposed for detection of mercury(II) in solution. This prestripping step was able to decrease the background and improve the signal‐to‐noise ratio and thus enhance the sensitivity. With this method, highly sensitive and selective detection of Hg²⁺ with a ppt‐level detection limit of 0.5 ng L^?1 could be achieved. Moreover, this method provides low interference, rapid and extreme simple and convenience, and hold great promise for in situ Hg²⁺ determination.     

金-钯双金属纳米颗粒修饰玻碳电极阳极溶出伏安法测定三价砷的方法研究

研究了金-钯双金属纳米颗粒修饰电极测定痕量砷的阳极溶出伏安法。采用紫外可见分光光度法、高分辨透射电镜及循环伏安法对颗粒的结构和电化学特性进行表征。采用方波伏安法测定三价砷,探讨了富集电位和方波伏安参数如频率、增幅、波幅以及干扰离子等对测定结果的影响。实验结果表明:金-钯双金属纳米颗粒呈壳-核结构;砷在0.30 V出现灵敏的阳极溶出伏安峰,峰电流与砷质量浓度在0.5～20μg/L范围内呈良好的线性关系,检出限为0.15μg/L;所制备的修饰电极重现性好,可用于三价砷的重复测定。共存离子Cu(Ⅱ)会影响三价砷的测定,而Pb(Ⅱ)、Cd(Ⅱ)、Zn(Ⅱ)等离子的存在对测定结果无影响。     

Square Wave Anodic Stripping Voltammetric Determination of Hg(II) with N1-Hydroxy-N1,N2-diphenylbenzamidine Modified Carbon Paste Electrode

Mercury is a highly toxic metal, of which even small doses (<200 ng mL⁻¹) can cause serious problems for humans, plants, animals and microorganisms, including marine species and freshwater organisms. Hence, a simple, fast, highly selective and sensitive and accurate method for the detection of mercury in the environmental, clinical or biological samples is necessary. A new, sensitive and selective method for the determination of Hg(II) with 5 % N¹-hydroxy-N¹,N²-diphenylbenzamidine modified carbon paste electrode has been developed. Hg(II) was accumulated for 210 s on the surface of the modified electrode using 0.1 M CH₃COONa of pH 7 at −0.8 V vs Ag/AgCl, followed by electrochemical stripping with SWASV in 0.1 M NH₄Cl at pH 4. The linear range is 0.02–10 μM Hg(II) with limit of detection of 1.28 nM. The method has RSDs of 3.7 %. The method was applied for the determination Hg(II) in five types of water samples. The recoveries were in the range 97.8–103 %. The proposed method was found to be highly selective and sensitive and has many attractive features compared to previous reports such as low cost, simplicity of electrode preparation, long term stability, fast response, easy renewable ability, and reasonable short accumulation time.     

Adsorptive Stripping Voltammetric Detection of Single‐Stranded DNA at Electrochemically Modified Glassy Carbon Electrode

Electrochemically modified glassy carbon electrode (GCE) was used to study the electrochemical oxidation and detection of denatured single‐stranded (ss) DNA by means of adsorptive stripping voltammetry. The modification of GCE, by electrochemical oxidation at +1.75 V (vs.SCE) for 10 min and cyclic sweep between +0.3 V and ?1.3 V for 20 cycles in pH 5.0 phosphate buffer, results in 100‐fold improvement in sensitivity for ssDNA detection. We speculated that the modified GCE has a high affinity to single‐stranded DNA through hydrogen bond (specific static adsorption). Single‐stranded DNA can accumulate at the GCE surface at open circuit and produce a well‐defined oxidation peak corresponding to the guanine residues at about +0.80 V in pH 5.0 phosphate buffer, while the native DNA gives no signal under the same condition. The peak currents are proportional to the ssDNA concentration in the range of 0–18.0 μg mL^?1. The detection limit of denatured ssDNA is ca. 0.2 μg mL^?1 when the accumulation time is 8 min at open circuit. The accumulation mechanism of ssDNA on the modified GCE was discussed.     

Over‐Oxidized Poly (Phenol Red) Film Modified Glassy Carbon Electrode for Anodic Stripping Voltammetric Determination of Ultra‐Trace Antimony (III)

In this study, we introduce a very sensitive and selective method for the differential pulse anodic stripping determination of Sb(III) ion on the over‐oxidized poly(phenol red) modified glassy carbon electrode (PPhRed_ox/GCE) in 0.1 mol L^‐1 HCl medium. The formation of both poly(phenol red) and over‐oxidized poly(phenol red) film on the electrode surfaces were characterized by electrochemical impedance spectroscopy, X‐ray photoelectron spectroscopy and scanning electron microscopy techniques. An anodic stripping peak of Sb(III) was observed at 0.015 V on the PPhRed_ox/GCE. Higher anodic stripping peak current of Sb(III) was obtained at PPhRed_ox/GCE compared with both bare GCE and poly(phenol red) film modified GCE (PPhRed/GCE). The calibration graph consisted of two linear segments of 0.044 ‐ 1.218 μg L⁻¹ and 3.40 – 18.26 μg L⁻¹ with a detection limit of 0.0075 μg L⁻¹. The proposed over‐oxidized polymer film modified electrode was applied successfully for the analysis of antimony in different spiked water samples. Spiked recoveries for water samples were obtained in the range of 93.0–103.0%. The accuracy of the method was also verified through the analysis of standard reference materials (SCP SCIENCE‐EnviroMAT™ EP−L‐2).     

Tellurium Film Electrodes Deposited on Carbon and Mesoporous Carbon Screen‐printed Substrates for Anodic Stripping Voltammetric Determination of Copper

The performance of screen‐printed electrodes modified in situ with tellurium film for the anodic stripping voltammetric (ASV) determination of Cu(II) is reported. It was found that two types of screen‐printed substrates, namely carbon and mesoporous carbon, were optimal for this application. The selected in situ tellurium film modified electrodes were applied for the square wave ASV determination of copper at μg L⁻¹ concentration levels. Well‐defined and reproducible Cu oxidation stripping peaks were produced at a potential more negative than the anodic dissolution of tellurium. The highest sensitivity of Cu determination was achieved in 0.05 M HCl containing 50 μg L⁻¹ Te(IV) after 300 s of accumulation at −0.5 V. Using the optimized procedure, a linear range from 2 to 35 μg L⁻¹ of Cu(II) was obtained with a detection limit of 0.5 μg L⁻¹ Cu(II) (S/N=3) for 300 s of deposition time. Both sensors, carbon TeF‐SPE and mesoporous carbon TeF‐SPE, were successfully applied for the quantification of Cu in a certified reference surface water sample.     

Sensitive Determination of Trace Pb2+ in Seawater Using Columnar Glassy Carbon Electrode

We herein report a mercury‐free approach for the sensitive determination of trace Pb²⁺ in seawater using differential pulse stripping voltammetric (DPSV) method with a novel columnar glassy carbon electrode (CGCE). Compared with the conventional disk glassy carbon electrode with the same diameter, it has much larger electrochemical area (0.627 ± 0.003 cm²). The CGCE shows good accumulation ability and consequently acceptable behavior which makes it suitable as a working electrode in the DPSV determination of Pb2+ with the great advantage of the avoidance of harmful mercury. Using acidified artificial seawater as supporting electrolyte, there was a good linear relationship between the peak currents and the concentration of Pb²⁺ in the range of 0.6～140.0 μg L^‐1 with a detection limit of 0.3 μg/L (S/N = 3) when the accumulation time was 300 s. The method was employed to determine trace levels of Pb²⁺ in real seawater samples successfully.     

Anodic Stripping Voltammetric Determination of Lead(II) Using Glassy Carbon Electrode Modified with Novel Calix[4]arene

Owingtothegrowingawarenessofleadpollutionandtoxicity,manytechniquesarecurrentlyemployedforthedeterminationoftracePbioninenvironmentalsamples .1Amongthem ,thedevelopmentofchemicallymodifiedelectrodes (CMEs)andapplicationsofanodicstrippingvoltammetry (ASV)havereceivedconsiderableattention .CMEsarecharacterizedbypurposefullyalteringtheirsur facecharacteristicstodisplaynewqualitiesthatcouldbeexploitedforanalyticalapplications .Thesekindsofelec trodesareinexpensiveandpossessmanyadvantagessuchas…     

Study on Cd2+ Determination Using Bud-like Poly-L-Tyrosine/Bi Composite Film Modified Glassy Carbon Electrode Combined with Eliminating of Cu2+ Interference by Electrodeposition

A bud-like poly-L-tyrosine/Bi modified glassy carbon electrode (p-Tyr/Bi/GC) was prepared by CV and in situ Bi plating, whose conductivity and membrane morphology were characterized by CV, EIS and SEM, respectively. The p-Tyr membrane can effectively promote the enrichment of Cd²⁺. The optimal Tyr concentration and scanning number for p-Tyr/GC preparation were 2.0 mmol ⋅ L⁻¹ and 35, while the optimal Bi³⁺ concentration, pH and Cd²⁺ accumulation potential in test medium were 3.0 μmol ⋅ L⁻¹, 6.5 and −1.3 V, respectively. The linear equation of p-Tyr/Bi/GC's response to Cd²⁺ (1.0 nmol ⋅ L⁻¹ to 2.0 μmol ⋅ L⁻¹) was i_p (μA) = −0.6809 + 100.2c (μmol ⋅ L⁻¹) (R² = 0.9985) with a detection limit of 0.11 nmol ⋅ L⁻¹ (3S/N). The elimination of interference caused by Cu²⁺ in sample was studied by electrodeposition. The p-Tyr/Bi/GC electrode was successfully used for detecting Cd in rice samples with good reliability and accuracy. The developed Cd²⁺ sensor exhibits high sensitivity, wide linear range and low detection limit, especially the designed method of eliminating Cu²⁺ interference has the characteristics of high selectivity, simple operation and wide application range.     

Anodic Stripping Voltammetric Determination of Lead（Ⅱ） Using Glassy Carbon Electrode Modified with Novel Calix[4] arene

A new glassy carbon electrode modified with novel calix[4]‐arene derivative was prepared and then applied to the selective recognition of lead ion in aqueous media by cyclic and square wave voltammetry. A new anodic stripping peak at ? 0.92 V (vs. Ag/Ag⁺) in square wave voltammogram can be obtained by scanning the potential from ? 1.5 to ? 0.6 V, of which the peak current is proportional to the concentration of Pb²⁺. The modified electrode in 0.1 mol/L HNO₃ solution showed a linear voltammetric response in the range of 2.0 × 10–⁸–1.0 × 10–⁶ mol/L and a detection limit of 6.1 × 10–⁹ mol/L. In the modified glassy carbon electrode no significant interference occurred from alkali, alkaline and transition metal ions except Hg²⁺, Ag⁺ and Cu²⁺ ions, which can be eliminated by the addition of KSCN. The proposed method was successfully applied to determine lead in aqueous samples.     

Determination of Copper(II) Through Anodic Stripping Voltammetry in Tartrate Buffer Using an Antimony Film Screen-printed Carbon Electrode

The voltammetric performance of an in situ plated antimony film screen-printed carbon electrode in hydrochloric acid, acetate buffer, and tartrate buffer was evaluated for the detection of copper(II) with differential pulse anodic stripping voltammetry. The tartrate buffer was superior, providing high sensitivity and good separation of copper and antimony stripping peaks. The analytical conditions for the determination of copper(II) were optimized. The detection limit was estimated to be 0.14?µg?L^?1 copper(II) and the relative standard deviation for 2.5?µg?L^?1 copper(II) was 3%. The applicability of the method was illustrated by the analysis of soil conditioner samples.     

Voltammetric Determination of Rutin Using a Carbon Composite Electrode Modified with Copper(II)-Resin

Abstract

The preparation and electrochemical characterization of a carbon composite electrode modified with copper(II)-resin as well as its behavior toward rutin were investigated using cyclic and linear sweep voltammetry. The best voltammetric response was observed for a composite composition of 20% (m/m) copper(II)-resin, 0.10 mol L^?1 KNO₃/10^?6 mol L^?1 HNO₃ solution (pH 6.0) as the supporting electrolyte, and a scan rate of 50 mVs^?1. A linear voltammetric response for rutin was obtained in the concentration range from 9.90 × 10^?7 to 8.07 × 10^?6 mol L^?1, with a detection limit of 2.65 × 10^?8 mol L^?1. The proposed electrode was useful for the quality control and routine analysis of rutin in pharmaceutical formulations.     

Differential Pulse Anodic Stripping Voltammetric Simultaneous Determination of Copper(II) and Silver(I) with Bis(2‐hydroxyacetophenone) Butane‐2,3‐dihydrazone Modified Carbon Paste Electrodes

The behavior of a modified carbon paste electrode (CPE) for simultaneous determination of copper(II) and silver(I) by anodic adsorptive stripping voltammetry (ASV) was studied. The electrode was built incorporating the bis(2‐hydroxyacetophenone) butane‐2,3‐dihydrazone (BHAB) as a complexing agent to a Nujol‐graphite base paste. The resulting electrode demonstrated linear responses over the range of Cu(II) and Ag(I) concentrations 0.1–20 and 0.01–2.0 µM respectively. The relative standard deviation (RSD) for the determination of 5.0 µM of both metal ions were 2.9 and 3.1 % for Cu(II) and Ag(I), respectively. The method has been applied to the analysis of copper in wheat and barley seed samples and silver in developed radiological film.     

Determination of Atrazine in Natural Water Samples by Differential Pulse Adsorptive Stripping Voltammetry Using a Bismuth Film Electrode

A new method using differential pulse adsorptive stripping voltammetry for the determination of atrazine (ATZ) in natural water samples using a bismuth film electrode (BiFE) is proposed. The calibration curve was linear in the atrazine concentration range from 6.7×10^?7 to 2.0×10^?5 mol L^?1, with a limit of detection (LOD) of 1.4×10^?7 mol L^?1. The proposed electrode was applied for atrazine determination with satisfactory results compared with a high‐performance liquid chromatography method (HPLC).     

Anodic Stripping Voltammetric Determination of Aurothiomalate in Urine Using a Screen‐Printed Carbon Electrode

This work describes an electroanalytical method for determining gold(I) thiomalate, aurothiomalate, widely used for treatment of reumatoid arthiritis, using a screen‐printed carbon electrode (SPCE). Aurothiomalate (AuTM) was determined indirectly at the same electrode by accumulating it first at ?1.5 V vs. printed carbon. At this potential in the adsorbed state, the AuTM is reduced to Au(0), which is then oxidized at two steps at ?0.22 V and +0.54 V on SPCE. Using optimized conditions of 60 s deposition time, ?1.5 V (vs. printed carbon) accumulation potential, 100 mV s^?1 scan rate, linear calibration graphs can be obtained by monitoring the peak at +0.54 V for AuTM in HCl 0.1 mol L^?1 from 1.43×10^?6 to 1.55×10^?4 mol L^?1. A limit of detection obtained was 6.50×10^?7 mol L^?1, and the relative standard deviation from five measurements of 3.0×10^?5 mol L^?1 AuTM is 4.5%. The method was successfully applied for AuTM determination in human urine sample.     

Anodic Stripping Voltammetry Determination of Pb(II) and Cd(II) at a Bismuth/Poly(aniline) Film Electrode

Abstract

A novel voltammetric method—anodic—using a bismuth/poly(aniline) film electrode has been developed for simultaneous measurement of Pb(II) and Cd(II) at low µg L^?1 concentration levels by stripping voltammetry. The results confirmed that the bismuth/poly(aniline) film electrode offered high‐quality stripping performance compared with the bismuth film electrode. Well‐defined sharp stripping peaks were observed for Pb(II) and Cd(II), along with an extremely low baseline. The detection limits of Pb(II) and Cd(II) are 1.03 µg L^?1 and 1.48 µg L^?1, respectively. The bismuth/poly (aniline) electrode has been applied to the determination of Pb(II) in tap water samples with satisfactory results.     

Anodic Stripping Voltammetric Determination of Mercury(II) in Water Using a 4‐Tert‐Butyl‐1‐(Ethoxycarbonylmethoxy)Thiacalix[4]Arene Modified Glassy Carbon Electrode

A glassy carbon electrode coated the film of 4‐tert‐butyl‐1‐(ethoxycarbonylmethoxy)thiacalix[4]arene is designed for the determination of trace amounts of Hg²⁺. Compared with bare glassy carbon electrode, the modified electrode can improve the measuring sensitivity of Hg²⁺. Under the optimum experimental condition, the modified electrode in 0.1 mol L^?1 H₂SO₄ + 0.01 mol L^?1 KCl solution shows a linear voltammetric response in the range of 8.0 × 10^?9 ～ 3.0 × 10^?6 mol L^?1 with detection limit 5.0 × 10^?9 mol L^?1 for Hg²⁺. The high sensitivity, selectivity, and stability of modified electrode also prove its practical application for a simple, rapid and economical determination of Hg²⁺ in water samples.     

Differential Pulse Anodic Stripping Voltammetric Determination of Bismuth(III) with 1‐(2‐Pyridylazo)‐2‐naphthol and Ionic Liquid Modified Carbon Paste Electrode

In this paper 1‐(2‐pyridylazo)‐2‐naphthol (PAN) and ionic liquid 1‐ethyl‐3‐methylimidazolium tetrafluoroborate (EMIMBF₄) were mixed with graphite powder to get a modified carbon paste electrode (PAN‐IL‐CPE), which was further used for the sensitive determination of bismuth(III). By the co‐contribution of the formation of PAN‐Bi complex and the accumulation effect of IL, more bismuth(III) was electrodeposited on the surface of the PAN‐IL‐CPE. Then the reduced Bi was oxidized and detected by differential pulse anodic stripping voltammetry (DPASV) with the oxidation peak appeared at 0.17 V (vs. SCE). Under the optimal conditions the oxidation peak current was proportional to the bismuth(III) concentration in the range from 0.04 to 7.5 μmol L^?1 with the detection limit as 3.9 nmol L^?1. The proposed method was successfully applied to the stomach medicine sample detection with good recovery.